AP2 2004–05 (F22C1, cable) → Speeduino Speeduino v0.4 (auto)
AP2 2004–05 (F22C1, cable) — Speeduino — Speeduino
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-04
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
OEM-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Coolant temp gauge drive | — | W37 | — | 0.5 | SPEEDUINO-A-30 | — | — | — |
| 2 | Air control valve solenoid | — | — | — | — | — | — | — | — |
| 3 | Evap bypass solenoid | — | — | — | — | — | — | — | — |
| 4 | Evap canister vent shut valve | — | — | — | — | — | — | — | — |
| 5 | NC | — | — | — | — | — | — | — | — |
| 6 | Evap canister purge valve | — | — | — | — | — | — | — | — |
| 7 | NC | — | — | — | — | — | — | — | — |
| 8 | NC | — | — | — | — | — | — | — | — |
| 9 | Vehicle speed sensor | — | W44 | — | 0.5 | SPEEDUINO-A-14 | — | — | — |
| 10 | Service check signal | — | — | — | — | — | — | — | — |
| 11 | NC | — | — | — | — | — | — | — | — |
| 12 | Immobilizer indicator light | — | — | — | — | — | — | — | — |
| 13 | Immobilizer enable signal | — | — | — | — | — | — | — | — |
| 14 | NC | — | — | — | — | — | — | — | — |
| 15 | Fuel pump relay (USDM) | — | W28 | — | 0.5 | SPEEDUINO-A-16 | — | — | — |
| 16 | Fuel pump relay (JDM) | — | W29 | — | 0.5 | SPEEDUINO-A-15 | — | — | — |
| 17 | A/C clutch relay | — | W30 | — | 0.5 | SPEEDUINO-A-36 | — | — | — |
| 18 | Check engine light (MIL) | — | — | — | — | — | — | — | — |
| 19 | Tacho output | — | W38 | — | 0.5 | SPEEDUINO-A-17 | — | — | — |
| 20 | Radiator fan relay | — | W31 | — | 0.5 | SPEEDUINO-A-35 | — | — | — |
| 21 | K-Line | — | — | — | — | — | — | — | — |
| 22 | NC | — | — | — | — | — | — | — | — |
| 23 | Secondary O2 sensor | — | W41 | — | 0.5 | SPEEDUINO-A-21 | — | — | — |
| 24 | Starter switch signal | — | — | — | — | — | — | — | — |
| 25 | Immobilizer code | — | — | — | — | — | — | — | — |
| 26 | Power steering load detect | — | — | — | — | — | — | — | — |
| 27 | A/C switch (request) | — | — | — | — | — | — | — | — |
| 28 | Air pump relay | — | W32 | — | 0.5 | SPEEDUINO-A-37 | — | — | — |
| 29 | Fuel tank pressure sensor | — | — | — | — | — | — | — | — |
| 30 | Electrical load detector | — | — | — | — | — | — | — | — |
| 31 | NC | — | — | — | — | — | — | — | — |
| 32 | Brake switch | — | — | — | — | — | — | — | — |
OEM-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Power source 1 (main relay) | — | — | — | — | — | — | — | — |
| 2 | Power ground 1 | — | W2 | — | 0.85 | SP-GND-1 | — | — | — |
| 3 | Injector 2 | — | W25 | — | 0.5 | SPEEDUINO-A-2 | — | — | — |
| 4 | Injector 3 | — | W26 | — | 0.5 | SPEEDUINO-A-3 | — | — | — |
| 5 | Injector 4 | — | W27 | — | 0.5 | SPEEDUINO-A-5 | — | — | — |
| 6 | NC | — | — | — | — | — | — | — | — |
| 7 | NC | — | — | — | — | — | — | — | — |
| 8 | NC | — | — | — | — | — | — | — | — |
| 9 | Power source 2 (main relay) | — | — | — | — | — | — | — | — |
| 10 | Power ground 2 | — | W1 | — | 0.85 | SP-GND-1 | — | — | — |
| 11 | Injector 1 | — | W24 | — | 0.5 | SPEEDUINO-A-1 | — | — | — |
| 12 | VTEC solenoid | — | W33 | — | 0.5 | SPEEDUINO-A-31 | — | — | — |
| 13 | NC | — | — | — | — | — | — | — | — |
| 14 | NC | — | — | — | — | — | — | — | — |
| 15 | NC | — | — | — | — | — | — | — | — |
| 16 | NC | — | — | — | — | — | — | — | — |
| 17 | NC | — | — | — | — | — | — | — | — |
| 18 | NC | — | — | — | — | — | — | — | — |
| 19 | NC | — | — | — | — | — | — | — | — |
| 20 | Ground | — | W3 | — | 0.85 | SP-GND-1 | — | — | — |
| 21 | Backup power (battery constant) | — | — | — | — | — | — | — | — |
| 22 | Ground | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| 23 | Idle air control valve | — | W36 | — | 0.5 | SPEEDUINO-A-29 | — | — | — |
| 24 | NC | — | — | — | — | — | — | — | — |
| 25 | NC | — | — | — | — | — | — | — | — |
OEM-C
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Primary O2 heater | — | W34 | — | 0.5 | SPEEDUINO-A-38 | — | — | — |
| 2 | Alternator control | — | — | — | — | — | — | — | — |
| 3 | Knock sensor | — | — | — | — | — | — | — | — |
| 4 | Ignition coil 1 | — | W20 | — | 0.5 | SPEEDUINO-A-7 | — | — | — |
| 5 | Alternator FR signal | — | W45 | — | 0.5 | SPEEDUINO-A-18 | — | — | — |
| 6 | NC | — | — | — | — | — | — | — | — |
| 7 | Sensor ground 1 | — | W10 | — | 0.5 | SP-0V-1 | — | — | — |
| 8 | Crank sensor + (CKP+) | — | W15 | — | 0.5 | SPEEDUINO-A-25 | — | — | — |
| 9 | Crank sensor − (CKP−) | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 10 | VTEC pressure switch | — | — | — | — | — | — | — | — |
| 11 | Secondary O2 heater control | — | W35 | — | 0.5 | SPEEDUINO-A-32 | — | — | — |
| 12 | Ignition coil 2 | — | W21 | — | 0.5 | SPEEDUINO-A-34 | — | — | — |
| 13 | Ignition coil 3 | — | W22 | — | 0.5 | SPEEDUINO-A-33 | — | — | — |
| 14 | Ignition coil 4 | — | W23 | — | 0.5 | SPEEDUINO-A-8 | — | — | — |
| 15 | Secondary O2 sensor | — | — | — | — | — | — | — | — |
| 16 | Primary O2 sensor | — | — | — | — | — | — | — | — |
| 17 | MAP sensor | — | W39 | — | 0.5 | SPEEDUINO-A-11 | — | — | — |
| 18 | Sensor ground 2 | — | W7 | — | 0.5 | SP-0V-1 | — | — | — |
| 19 | Sensor 5V supply 1 (MAP) | — | W13 | — | 0.5 | SPEEDUINO-A-13 | — | — | — |
| 20 | Cam (TDC1) sensor + | — | W17 | — | 0.5 | SPEEDUINO-A-24 | — | — | — |
| 21 | Cam (TDC1) sensor − | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | Knock sensor | — | — | — | — | — | — | — | — |
| 23 | NC | — | — | — | — | — | — | — | — |
| 24 | Air pump electric current sensor | — | — | — | — | — | — | — | — |
| 25 | Intake air temp sensor | — | W43 | — | 0.5 | SPEEDUINO-A-20 | — | — | — |
| 26 | Coolant temp sensor | — | W42 | — | 0.5 | SPEEDUINO-A-19 | — | — | — |
| 27 | Throttle position sensor | — | W40 | — | 0.5 | SPEEDUINO-A-22 | — | — | — |
| 28 | Sensor 5V supply 2 | — | W14 | — | 0.5 | SPEEDUINO-A-28 | — | — | — |
| 29 | Cam (TDC2) sensor + | — | W19 | — | 0.5 | SPEEDUINO-A-26 | — | — | — |
| 30 | Cam (TDC2) sensor − | — | W8 | — | 0.5 | SP-0V-1 | — | — | — |
| 31 | Timing ground | — | W9 | — | 0.5 | SP-0V-1 | — | — | — |
OEM-D
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | NC | — | — | — | — | — | — | — | — |
| 2 | NC | — | — | — | — | — | — | — | — |
| 3 | NC | — | — | — | — | — | — | — | — |
| 4 | NC | — | — | — | — | — | — | — | — |
| 5 | NC | — | — | — | — | — | — | — | — |
| 6 | NC | — | — | — | — | — | — | — | — |
| 7 | NC | — | — | — | — | — | — | — | — |
| 8 | NC | — | — | — | — | — | — | — | — |
| 9 | NC | — | — | — | — | — | — | — | — |
| 10 | NC | — | — | — | — | — | — | — | — |
| 11 | NC | — | — | — | — | — | — | — | — |
| 12 | NC | — | — | — | — | — | — | — | — |
| 13 | NC | — | — | — | — | — | — | — | — |
| 14 | NC | — | — | — | — | — | — | — | — |
| 15 | NC | — | — | — | — | — | — | — | — |
| 16 | NC | — | — | — | — | — | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W10 | — | 0.5 | OEM-C-7 | — | — | — |
| 1 | — | — | W7 | — | 0.5 | OEM-C-18 | — | — | — |
| 1 | — | — | W8 | — | 0.5 | OEM-C-30 | — | — | — |
| 1 | — | — | W9 | — | 0.5 | OEM-C-31 | — | — | — |
| 1 | — | — | W11 | — | 0.5 | SPEEDUINO-A-12 | — | — | — |
| 1 | — | — | W12 | — | 0.5 | SPEEDUINO-A-23 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-C-9 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | OEM-C-21 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-B-10 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-B-2 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | OEM-B-20 | — | — | — |
| 1 | — | — | W4 | — | 0.85 | OEM-B-22 | — | — | — |
| 1 | — | — | W5 | — | 0.85 | SPEEDUINO-A-10 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | SPEEDUINO-A-9 | — | — | — |
SPEEDUINO-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector 1 | — | W24 | — | 0.5 | OEM-B-11 | — | — | — |
| 10 | Ground | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 11 | MAP sensor (0-5V) | — | W39 | — | 0.5 | OEM-C-17 | — | — | — |
| 12 | Ground | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| 13 | 5V | — | W13 | — | 0.5 | OEM-C-19 | — | — | — |
| 14 | Proto area 1 (flex fuel) | — | W44 | — | 0.5 | OEM-A-9 | — | — | — |
| 15 | Proto area 2 (fan) | — | W29 | — | 0.5 | OEM-A-16 | — | — | — |
| 16 | Proto area 3 (fuel pump) | — | W28 | — | 0.5 | OEM-A-15 | — | — | — |
| 17 | Proto area 4 (tachometer) | — | W38 | — | 0.5 | OEM-A-19 | — | — | — |
| 18 | Proto area 5 (clutch) | — | W45 | — | 0.5 | OEM-C-5 | — | — | — |
| 19 | Coolant temp (CLT) | — | W42 | — | 0.5 | OEM-C-26 | — | — | — |
| 2 | Injector 2 | — | W25 | — | 0.5 | OEM-B-3 | — | — | — |
| 20 | Inlet air temp (IAT) | — | W43 | — | 0.5 | OEM-C-25 | — | — | — |
| 21 | O2 sensor | — | W41 | — | 0.5 | OEM-A-23 | — | — | — |
| 22 | TPS input | — | W40 | — | 0.5 | OEM-C-27 | — | — | — |
| 23 | Ground | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | Cam input / VR2+ | — | W17 | — | 0.5 | OEM-C-20 | — | — | — |
| 25 | Crank input / VR1+ | — | W15 | — | 0.5 | OEM-C-8 | — | — | — |
| 26 | VR2- | — | W19 | — | 0.5 | OEM-C-29 | — | — | — |
| 27 | VR1- | — | — | — | — | — | — | — | — |
| 28 | 5V | — | W14 | — | 0.5 | OEM-C-28 | — | — | — |
| 29 | Idle stepper 2B | — | W36 | — | 0.5 | OEM-B-23 | — | — | — |
| 3 | Injector 3 | — | W26 | — | 0.5 | OEM-B-4 | — | — | — |
| 30 | Idle stepper 2A | — | W37 | — | 0.5 | OEM-A-1 | — | — | — |
| 31 | Idle stepper 1A | — | W33 | — | 0.5 | OEM-B-12 | — | — | — |
| 32 | Idle stepper 1B | — | W35 | — | 0.5 | OEM-C-11 | — | — | — |
| 33 | Ignition 3 | — | W22 | — | 0.5 | OEM-C-13 | — | — | — |
| 34 | Ignition 2 | — | W21 | — | 0.5 | OEM-C-12 | — | — | — |
| 35 | Boost | — | W31 | — | 0.5 | OEM-A-20 | — | — | — |
| 36 | Idle 2 (3-wire idle) | — | W30 | — | 0.5 | OEM-A-17 | — | — | — |
| 37 | PWM idle | — | W32 | — | 0.5 | OEM-A-28 | — | — | — |
| 38 | VVT | — | W34 | — | 0.5 | OEM-C-1 | — | — | — |
| 5 | Injector 4 | — | W27 | — | 0.5 | OEM-B-5 | — | — | — |
| 7 | Ignition 1 | — | W20 | — | 0.5 | OEM-C-4 | — | — | — |
| 8 | Ignition 4 | — | W23 | — | 0.5 | OEM-C-14 | — | — | — |
| 9 | Ground | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-A-1 | Coolant temp gauge drive | low_side_out | SPEEDUINO-A-30 | Idle stepper 2A | hbridge_out | corroborated | |
| OEM-A-10 | Service check signal | — | — | — | — | single_source | |
| OEM-A-11 | NC | — | — | — | — | unverified | |
| OEM-A-12 | Immobilizer indicator light | low_side_out | — | — | — | single_source | |
| OEM-A-13 | Immobilizer enable signal | — | — | — | — | single_source | |
| OEM-A-14 | NC | — | — | — | — | unverified | |
| OEM-A-15 | Fuel pump relay (USDM) | low_side_out | SPEEDUINO-A-16 | Proto area 3 (fuel pump) | low_side_out | corroborated | |
| OEM-A-16 | Fuel pump relay (JDM) | low_side_out | SPEEDUINO-A-15 | Proto area 2 (fan) | low_side_out | single_source | |
| OEM-A-17 | A/C clutch relay | low_side_out | SPEEDUINO-A-36 | Idle 2 (3-wire idle) | low_side_out | corroborated | |
| OEM-A-18 | Check engine light (MIL) | low_side_out | — | — | — | corroborated | |
| OEM-A-19 | Tacho output | tacho_out | SPEEDUINO-A-17 | Proto area 4 (tachometer) | tacho_out | corroborated | |
| OEM-A-2 | Air control valve solenoid | low_side_out | — | — | — | single_source | |
| OEM-A-20 | Radiator fan relay | low_side_out | SPEEDUINO-A-35 | Boost | low_side_out | corroborated | |
| OEM-A-21 | K-Line | serial | — | — | — | single_source | |
| OEM-A-22 | NC | — | — | — | — | unverified | |
| OEM-A-23 | Secondary O2 sensor | lambda_nb_in | SPEEDUINO-A-21 | O2 sensor | lambda_nb_in | single_source | |
| OEM-A-24 | Starter switch signal | digital_in | — | — | — | corroborated | |
| OEM-A-25 | Immobilizer code | — | — | — | — | single_source | |
| OEM-A-26 | Power steering load detect | digital_in | — | — | — | corroborated | |
| OEM-A-27 | A/C switch (request) | digital_in | — | — | — | corroborated | |
| OEM-A-28 | Air pump relay | low_side_out | SPEEDUINO-A-37 | PWM idle | low_side_out | corroborated | |
| OEM-A-29 | Fuel tank pressure sensor | analog_in | — | — | — | corroborated | |
| OEM-A-3 | Evap bypass solenoid | low_side_out | — | — | — | single_source | |
| OEM-A-30 | Electrical load detector | analog_in | — | — | — | corroborated | |
| OEM-A-31 | NC | — | — | — | — | unverified | |
| OEM-A-32 | Brake switch | digital_in | — | — | — | corroborated | |
| OEM-A-4 | Evap canister vent shut valve | low_side_out | — | — | — | single_source | |
| OEM-A-5 | NC | — | — | — | — | unverified | |
| OEM-A-6 | Evap canister purge valve | low_side_out | — | — | — | single_source | |
| OEM-A-7 | NC | — | — | — | — | unverified | |
| OEM-A-8 | NC | — | — | — | — | unverified | |
| OEM-A-9 | Vehicle speed sensor | digital_in | SPEEDUINO-A-14 | Proto area 1 (flex fuel) | digital_in | corroborated | |
| OEM-B-1 | Power source 1 (main relay) | power_in | — | — | — | corroborated | |
| OEM-B-10 | Power ground 2 | ground | SPEEDUINO-A-10 + SPEEDUINO-A-9 | Ground + Ground | ground | single_source | |
| OEM-B-11 | Injector 1 | injector_out | SPEEDUINO-A-1 | Injector 1 | injector_out | corroborated | |
| OEM-B-12 | VTEC solenoid | high_side_out | SPEEDUINO-A-31 | Idle stepper 1A | hbridge_out | corroborated | |
| OEM-B-13 | NC | — | — | — | — | unverified | |
| OEM-B-14 | NC | — | — | — | — | unverified | |
| OEM-B-15 | NC | — | — | — | — | unverified | |
| OEM-B-16 | NC | — | — | — | — | unverified | |
| OEM-B-17 | NC | — | — | — | — | unverified | |
| OEM-B-18 | NC | — | — | — | — | unverified | |
| OEM-B-19 | NC | — | — | — | — | unverified | |
| OEM-B-2 | Power ground 1 | ground | SPEEDUINO-A-10 + SPEEDUINO-A-9 | Ground + Ground | ground | corroborated | |
| OEM-B-20 | Ground | ground | SPEEDUINO-A-10 + SPEEDUINO-A-9 | Ground + Ground | ground | single_source | |
| OEM-B-21 | Backup power (battery constant) | power_in | — | — | — | single_source | |
| OEM-B-22 | Ground | ground | SPEEDUINO-A-10 + SPEEDUINO-A-9 | Ground + Ground | ground | single_source | |
| OEM-B-23 | Idle air control valve | low_side_out | SPEEDUINO-A-29 | Idle stepper 2B | hbridge_out | corroborated | |
| OEM-B-24 | NC | — | — | — | — | unverified | |
| OEM-B-25 | NC | — | — | — | — | unverified | |
| OEM-B-3 | Injector 2 | injector_out | SPEEDUINO-A-2 | Injector 2 | injector_out | corroborated | |
| OEM-B-4 | Injector 3 | injector_out | SPEEDUINO-A-3 | Injector 3 | injector_out | corroborated | |
| OEM-B-5 | Injector 4 | injector_out | SPEEDUINO-A-5 | Injector 4 | injector_out | corroborated | |
| OEM-B-6 | NC | — | — | — | — | unverified | |
| OEM-B-7 | NC | — | — | — | — | unverified | |
| OEM-B-8 | NC | — | — | — | — | unverified | |
| OEM-B-9 | Power source 2 (main relay) | power_in | — | — | — | corroborated | |
| OEM-C-1 | Primary O2 heater | low_side_out | SPEEDUINO-A-38 | VVT | low_side_out | corroborated | |
| OEM-C-10 | VTEC pressure switch | digital_in | — | — | — | corroborated | |
| OEM-C-11 | Secondary O2 heater control | low_side_out | SPEEDUINO-A-32 | Idle stepper 1B | hbridge_out | single_source | |
| OEM-C-12 | Ignition coil 2 | ignition_out | SPEEDUINO-A-34 | Ignition 2 | ignition_out | corroborated | |
| OEM-C-13 | Ignition coil 3 | ignition_out | SPEEDUINO-A-33 | Ignition 3 | ignition_out | corroborated | |
| OEM-C-14 | Ignition coil 4 | ignition_out | SPEEDUINO-A-8 | Ignition 4 | ignition_out | corroborated | |
| OEM-C-15 | Secondary O2 sensor | lambda_nb_in | — | — | — | corroborated | |
| OEM-C-16 | Primary O2 sensor | lambda_nb_in | — | — | — | corroborated | |
| OEM-C-17 | MAP sensor | analog_in | SPEEDUINO-A-11 | MAP sensor (0-5V) | analog_in | corroborated | |
| OEM-C-18 | Sensor ground 2 | sensor_ground | SPEEDUINO-A-12 + SPEEDUINO-A-23 | Ground + Ground | sensor_ground | corroborated | |
| OEM-C-19 | Sensor 5V supply 1 (MAP) | vref | SPEEDUINO-A-13 | 5V | vref | corroborated | |
| OEM-C-2 | Alternator control | low_side_out | — | — | — | single_source | |
| OEM-C-20 | Cam (TDC1) sensor + | trigger_in | SPEEDUINO-A-24 | Cam input / VR2+ | trigger_in | corroborated | |
| OEM-C-21 | Cam (TDC1) sensor − | trigger_in | SPEEDUINO-A-12 + SPEEDUINO-A-23 | Ground + Ground | sensor_ground | corroborated | |
| OEM-C-22 | Knock sensor | knock_in | — | — | — | conflict | |
| OEM-C-23 | NC | — | — | — | — | unverified | |
| OEM-C-24 | Air pump electric current sensor | analog_in | — | — | — | single_source | |
| OEM-C-25 | Intake air temp sensor | temp_in | SPEEDUINO-A-20 | Inlet air temp (IAT) | temp_in | corroborated | |
| OEM-C-26 | Coolant temp sensor | temp_in | SPEEDUINO-A-19 | Coolant temp (CLT) | temp_in | corroborated | |
| OEM-C-27 | Throttle position sensor | analog_in | SPEEDUINO-A-22 | TPS input | analog_in | corroborated | |
| OEM-C-28 | Sensor 5V supply 2 | vref | SPEEDUINO-A-28 | 5V | vref | corroborated | |
| OEM-C-29 | Cam (TDC2) sensor + | trigger_in | SPEEDUINO-A-26 | VR2- | trigger_in | corroborated | |
| OEM-C-3 | Knock sensor | knock_in | — | — | — | conflict | |
| OEM-C-30 | Cam (TDC2) sensor − | sensor_ground | SPEEDUINO-A-12 + SPEEDUINO-A-23 | Ground + Ground | sensor_ground | corroborated | |
| OEM-C-31 | Timing ground | sensor_ground | SPEEDUINO-A-12 + SPEEDUINO-A-23 | Ground + Ground | sensor_ground | single_source | |
| OEM-C-4 | Ignition coil 1 | ignition_out | SPEEDUINO-A-7 | Ignition 1 | ignition_out | corroborated | |
| OEM-C-5 | Alternator FR signal | digital_in | SPEEDUINO-A-18 | Proto area 5 (clutch) | digital_in | single_source | |
| OEM-C-6 | NC | — | — | — | — | unverified | |
| OEM-C-7 | Sensor ground 1 | sensor_ground | SPEEDUINO-A-12 + SPEEDUINO-A-23 | Ground + Ground | sensor_ground | corroborated | |
| OEM-C-8 | Crank sensor + (CKP+) | trigger_in | SPEEDUINO-A-25 | Crank input / VR1+ | trigger_in | corroborated | |
| OEM-C-9 | Crank sensor − (CKP−) | trigger_in | SPEEDUINO-A-12 + SPEEDUINO-A-23 | Ground + Ground | sensor_ground | corroborated | |
| OEM-D-1 | NC | — | — | — | — | unverified | |
| OEM-D-10 | NC | — | — | — | — | unverified | |
| OEM-D-11 | NC | — | — | — | — | unverified | |
| OEM-D-12 | NC | — | — | — | — | unverified | |
| OEM-D-13 | NC | — | — | — | — | unverified | |
| OEM-D-14 | NC | — | — | — | — | unverified | |
| OEM-D-15 | NC | — | — | — | — | unverified | |
| OEM-D-16 | NC | — | — | — | — | unverified | |
| OEM-D-2 | NC | — | — | — | — | unverified | |
| OEM-D-3 | NC | — | — | — | — | unverified | |
| OEM-D-4 | NC | — | — | — | — | unverified | |
| OEM-D-5 | NC | — | — | — | — | unverified | |
| OEM-D-6 | NC | — | — | — | — | unverified | |
| OEM-D-7 | NC | — | — | — | — | unverified | |
| OEM-D-8 | NC | — | — | — | — | unverified | |
| OEM-D-9 | NC | — | — | — | — | unverified |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-B-10 | SP-GND-1 | 0.85 | no route | Power ground 2 | — | |
| W2 | OEM-B-2 | SP-GND-1 | 0.85 | no route | Power ground 1 | — | |
| W3 | OEM-B-20 | SP-GND-1 | 0.85 | no route | Ground | — | |
| W4 | OEM-B-22 | SP-GND-1 | 0.85 | no route | Ground | — | |
| W5 | SP-GND-1 | SPEEDUINO-A-10 | 0.85 | no route | Ground | — | |
| W6 | SP-GND-1 | SPEEDUINO-A-9 | 0.85 | no route | Ground | — | |
| W7 | OEM-C-18 | SP-0V-1 | 0.5 | no route | Sensor ground 2 | — | |
| W8 | OEM-C-30 | SP-0V-1 | 0.5 | no route | Cam (TDC2) sensor − | — | |
| W9 | OEM-C-31 | SP-0V-1 | 0.5 | no route | Timing ground | — | |
| W10 | OEM-C-7 | SP-0V-1 | 0.5 | no route | Sensor ground 1 | — | |
| W11 | SP-0V-1 | SPEEDUINO-A-12 | 0.5 | no route | Ground | — | |
| W12 | SP-0V-1 | SPEEDUINO-A-23 | 0.5 | no route | Ground | — | |
| W13 | OEM-C-19 | SPEEDUINO-A-13 | 0.5 | no route | Sensor 5V supply 1 (MAP) | — | |
| W14 | OEM-C-28 | SPEEDUINO-A-28 | 0.5 | no route | Sensor 5V supply 2 | — | |
| W15 | OEM-C-8 | SPEEDUINO-A-25 | 0.5 | no route | Crank sensor + (CKP+) | — | |
| W16 | OEM-C-9 | SP-0V-1 | 0.5 | no route | Crank sensor − (CKP−) | — | |
| W17 | OEM-C-20 | SPEEDUINO-A-24 | 0.5 | no route | Cam (TDC1) sensor + | — | |
| W18 | OEM-C-21 | SP-0V-1 | 0.5 | no route | Cam (TDC1) sensor − | — | |
| W19 | OEM-C-29 | SPEEDUINO-A-26 | 0.5 | no route | Cam (TDC2) sensor + | — | |
| W20 | OEM-C-4 | SPEEDUINO-A-7 | 0.5 | no route | Ignition coil 1 | — | |
| W21 | OEM-C-12 | SPEEDUINO-A-34 | 0.5 | no route | Ignition coil 2 | — | |
| W22 | OEM-C-13 | SPEEDUINO-A-33 | 0.5 | no route | Ignition coil 3 | — | |
| W23 | OEM-C-14 | SPEEDUINO-A-8 | 0.5 | no route | Ignition coil 4 | — | |
| W24 | OEM-B-11 | SPEEDUINO-A-1 | 0.5 | no route | Injector 1 | — | |
| W25 | OEM-B-3 | SPEEDUINO-A-2 | 0.5 | no route | Injector 2 | — | |
| W26 | OEM-B-4 | SPEEDUINO-A-3 | 0.5 | no route | Injector 3 | — | |
| W27 | OEM-B-5 | SPEEDUINO-A-5 | 0.5 | no route | Injector 4 | — | |
| W28 | OEM-A-15 | SPEEDUINO-A-16 | 0.5 | no route | Fuel pump relay (USDM) | — | |
| W29 | OEM-A-16 | SPEEDUINO-A-15 | 0.5 | no route | Fuel pump relay (JDM) | — | |
| W30 | OEM-A-17 | SPEEDUINO-A-36 | 0.5 | no route | A/C clutch relay | — | |
| W31 | OEM-A-20 | SPEEDUINO-A-35 | 0.5 | no route | Radiator fan relay | — | |
| W32 | OEM-A-28 | SPEEDUINO-A-37 | 0.5 | no route | Air pump relay | — | |
| W33 | OEM-B-12 | SPEEDUINO-A-31 | 0.5 | no route | VTEC solenoid | — | |
| W34 | OEM-C-1 | SPEEDUINO-A-38 | 0.5 | no route | Primary O2 heater | — | |
| W35 | OEM-C-11 | SPEEDUINO-A-32 | 0.5 | no route | Secondary O2 heater control | — | |
| W36 | OEM-B-23 | SPEEDUINO-A-29 | 0.5 | no route | Idle air control valve | — | |
| W37 | OEM-A-1 | SPEEDUINO-A-30 | 0.5 | no route | Coolant temp gauge drive | — | |
| W38 | OEM-A-19 | SPEEDUINO-A-17 | 0.5 | no route | Tacho output | — | |
| W39 | OEM-C-17 | SPEEDUINO-A-11 | 0.5 | no route | MAP sensor | — | |
| W40 | OEM-C-27 | SPEEDUINO-A-22 | 0.5 | no route | Throttle position sensor | — | |
| W41 | OEM-A-23 | SPEEDUINO-A-21 | 0.5 | no route | Secondary O2 sensor | — | |
| W42 | OEM-C-26 | SPEEDUINO-A-19 | 0.5 | no route | Coolant temp sensor | — | |
| W43 | OEM-C-25 | SPEEDUINO-A-20 | 0.5 | no route | Intake air temp sensor | — | |
| W44 | OEM-A-9 | SPEEDUINO-A-14 | 0.5 | no route | Vehicle speed sensor | — | |
| W45 | OEM-C-5 | SPEEDUINO-A-18 | 0.5 | no route | Alternator FR signal | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 179679-6 | TE | S2000 2000–05 ECU harness plug B (25P, TE 040 Multi-Lock) | 1.000 | ea |
| connector | 179680-5 | TE | S2000 2000–05 ECU harness plug C (31P, TE 040 Multi-Lock) | 1.000 | ea |
| connector | 179681-6 | TE | S2000 2000–05 ECU harness plug A (32P, TE 040 Multi-Lock) | 1.000 | ea |
| connector | S2K-0005-ECU-D | Honda | S2000 2000–05 ECU plug D (P/N unknown) | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (20)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | NET_MERGED | OEM-C-18 + OEM-C-21 + OEM-C-30 + OEM-C-31 + OEM-C-7 + OEM-C-9 + SP-0V-1 + SPEEDUINO-A-12 + SPEEDUINO-A-23 | 2 different OEM functions share one net: OEM-C-21 Cam (TDC1) sensor −; OEM-C-9 Crank sensor − (CKP−) |
| error | REQUIRED_UNMAPPED | OEM-B-1 | Required OEM function "Power source 1 (main relay)" (power_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-B-9 | Required OEM function "Power source 2 (main relay)" (power_in) is not connected to the new ECU. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-1 | SPEEDUINO-A-1 "Injector 1" drives OEM-B-11 Injector 1 (load 1.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-15 | SPEEDUINO-A-15 "Proto area 2 (fan)" drives OEM-A-16 Fuel pump relay (JDM) (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-16 | SPEEDUINO-A-16 "Proto area 3 (fuel pump)" drives OEM-A-15 Fuel pump relay (USDM) (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-2 | SPEEDUINO-A-2 "Injector 2" drives OEM-B-3 Injector 2 (load 1.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-29 | SPEEDUINO-A-29 "Idle stepper 2B" drives OEM-B-23 Idle air control valve (load 1.0 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-3 | SPEEDUINO-A-3 "Injector 3" drives OEM-B-4 Injector 3 (load 1.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-31 | SPEEDUINO-A-31 "Idle stepper 1A" drives OEM-B-12 VTEC solenoid (load 1.0 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-35 | SPEEDUINO-A-35 "Boost" drives OEM-A-20 Radiator fan relay (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-36 | SPEEDUINO-A-36 "Idle 2 (3-wire idle)" drives OEM-A-17 A/C clutch relay (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-37 | SPEEDUINO-A-37 "PWM idle" drives OEM-A-28 Air pump relay (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | SPEEDUINO-A-5 | SPEEDUINO-A-5 "Injector 4" drives OEM-B-5 Injector 4 (load 1.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | NET_FAMILY | OEM-A-1 ↔ SPEEDUINO-A-30 | OEM-A-1 "Coolant temp gauge drive" [low_side_out] is wired to SPEEDUINO-A-30 "Idle stepper 2A" [hbridge_out]. A half-bridge can act as a low-side switch only if configured that way. |
| warn | NET_FAMILY | OEM-B-12 ↔ SPEEDUINO-A-31 | OEM-B-12 "VTEC solenoid" [high_side_out] is wired to SPEEDUINO-A-31 "Idle stepper 1A" [hbridge_out]. A half-bridge can act as a high-side switch only if configured that way. |
| warn | NET_FAMILY | OEM-B-23 ↔ SPEEDUINO-A-29 | OEM-B-23 "Idle air control valve" [low_side_out] is wired to SPEEDUINO-A-29 "Idle stepper 2B" [hbridge_out]. A half-bridge can act as a low-side switch only if configured that way. |
| warn | NET_FAMILY | OEM-C-11 ↔ SPEEDUINO-A-32 | OEM-C-11 "Secondary O2 heater control" [low_side_out] is wired to SPEEDUINO-A-32 "Idle stepper 1B" [hbridge_out]. A half-bridge can act as a low-side switch only if configured that way. |
| info | NET_FAMILY | OEM-C-7 ↔ OEM-C-21 | OEM-C-7 "Sensor ground 1" [sensor_ground] is wired to OEM-C-21 "Cam (TDC1) sensor −" [trigger_in]. Trigger return tied to sensor/trigger ground: correct for single-ended trigger inputs. |
| info | UNMAPPED | OEM | 24 optional OEM pins are not mapped: OEM-A-10 Service check signal; OEM-A-12 Immobilizer indicator light; OEM-A-13 Immobilizer enable signal; OEM-A-18 Check engine light (MIL); OEM-A-2 Air control valve solenoid; OEM-A-21 K-Line; OEM-A-24 Starter switch signal; OEM-A-25 Immobilizer code; OEM-A-26 Power steering load detect; OEM-A-27 A/C switch (request); OEM-A-29 Fuel tank pressure sensor; OEM-A-3 Evap bypass solenoid; OEM-A-30 Electrical load detector; OEM-A-32 Brake switch; OEM-A-4 Evap canister vent shut valve; OEM-A-6 Evap canister purge valve; OEM-B-21 Backup power (battery constant); OEM-C-10 VTEC pressure switch; OEM-C-15 Secondary O2 sensor; OEM-C-16 Primary O2 sensor; OEM-C-2 Alternator control; OEM-C-22 Knock sensor; OEM-C-24 Air pump electric current sensor; OEM-C-3 Knock sensor |
Accepted (0)
| Code | Subject | Reason | By |
|---|
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-04. Review every wire against both manuals before building. Open items: - Main-relay feed: no ecu_main_power pin on the stock or the new ECU - OEM-B 1: Power source 1 (main relay): no rule for class ecu_main_power; wire by hand - OEM-B 9: Power source 2 (main relay): no rule for class ecu_main_power; wire by hand Not wired: - OEM-B 21: Backup power (battery constant): Speeduino Speeduino has no battery-constant input; not needed - OEM-C 3: Knock sensor: no free knock input on Speeduino Speeduino - OEM-C 22: Knock sensor: no free knock input on Speeduino Speeduino - OEM-A 12: Immobilizer indicator light: no free low_side/ls_hs/injector/hbridge on Speeduino Speeduino - OEM-A 18: Check engine light (MIL): no free low_side/ls_hs/injector/hbridge on Speeduino Speeduino - OEM-A 2: Air control valve solenoid: no free low_side/ls_hs/injector/hbridge on Speeduino Speeduino - OEM-A 3: Evap bypass solenoid: no free low_side/ls_hs/injector/hbridge on Speeduino Speeduino - OEM-A 4: Evap canister vent shut valve: no free low_side/ls_hs/injector/hbridge on Speeduino Speeduino - OEM-A 6: Evap canister purge valve: no free low_side/ls_hs/injector/hbridge on Speeduino Speeduino - OEM-C 2: Alternator control: no free low_side/ls_hs/injector/hbridge on Speeduino Speeduino - OEM-C 15: Secondary O2 sensor: no free o2_narrowband/analog_0_5 on Speeduino Speeduino - OEM-C 16: Primary O2 sensor: no free o2_narrowband/analog_0_5 on Speeduino Speeduino - OEM-A 29: Fuel tank pressure sensor: no free analog_0_5 on Speeduino Speeduino - OEM-A 30: Electrical load detector: no free analog_0_5 on Speeduino Speeduino - OEM-C 24: Air pump electric current sensor: no free analog_0_5 on Speeduino Speeduino - OEM-A 24: Starter switch signal: no free switch_in/frequency_in/analog_0_5 on Speeduino Speeduino - OEM-A 26: Power steering load detect: no free switch_in/frequency_in/analog_0_5 on Speeduino Speeduino - OEM-A 27: A/C switch (request): no free switch_in/frequency_in/analog_0_5 on Speeduino Speeduino - OEM-A 32: Brake switch: no free switch_in/frequency_in/analog_0_5 on Speeduino Speeduino - OEM-C 10: VTEC pressure switch: no free switch_in/frequency_in/analog_0_5 on Speeduino Speeduino - OEM-A 21: K-Line: no free k_line on Speeduino Speeduino - OEM-A 10: Service check signal: not classified in the library; wire by hand - OEM-A 13: Immobilizer enable signal: not classified in the library; wire by hand - OEM-A 25: Immobilizer code: not classified in the library; wire by hand
Sources
| Reliability | Kind | Title | URL |
|---|---|---|---|
| 4 | vendor_doc | AEM 30-6052 Series 2 Plug & Play EMS, 2000–2005 S2000 (original ECU pinout) | https://documents.aemelectronics.com/techlibrary_30-6052_series_2_plug___play_ems.pdf |
| 4 | vendor_doc | Haltech KB: F20C (AP1) engine | https://support.haltech.com/portal/en/kb/articles/f20c-ap1-engine |
| 4 | vendor_doc | Link S2000 AP1 PlugIn installation manual | https://linkecu.com/documentation/S2000X.pdf |
| 4 | vendor_doc | Speeduino Manual (08/04/25) — V0.4 board IDC40 pinout & features | https://speeduino.com/Speeduino_manual.pdf |
| 2 | forum | AllPinouts: 2000–2005 Honda S2000 ECU | https://allpinouts.org/pinouts/connectors/car/2000-2005-honda-s2000-ecu/ |
| 2 | forum | Autodata blog: ECU Pinout Honda S2000 2000-2004 | http://autodatas.blogspot.com/2012/11/ecu-pinout-honda-s2000-2000-2004.html |
| 2 | derived | Typical load estimates (relay coil ~0.2 A, high-Z injector ~1.2 A, VVT solenoid ~1 A) | — |