S2000 AP2 2006–09 DBW → Emtron SL8
AP2 2006–09 (F22C1, DBW) — Emtron — SL8
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-04
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
S2K-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Knock sensor | — | W25 | — | 0.5 | SL8-B-16 | — | — | — |
| 2 | Ignition power 2 | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 3 | Ignition power 1 | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 4 | Power ground 2 | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | Power ground 1 | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Cam position sensor (T2) | — | W24 | — | 0.5 | SL8-B-7 | — | — | — |
| 7 | Crank position sensor (T1) | — | W23 | — | 0.5 | SL8-B-5 | — | — | — |
| 8 | Logic ground 2 | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 9 | Logic ground 1 | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 10 | A/F sensor heater | — | — | — | — | — | — | — | — |
| 11 | Unused cavity | — | — | — | — | — | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Ignition coil 4 | — | W51 | — | 0.5 | SL8-A-29 | — | — | — |
| 14 | Ignition coil 3 | — | W50 | — | 0.5 | SL8-A-28 | — | — | — |
| 15 | Ignition coil 2 | — | W49 | — | 0.5 | SL8-A-27 | — | — | — |
| 16 | Ignition coil 1 | — | W48 | — | 0.5 | SL8-A-26 | — | — | — |
| 17 | Unused cavity | — | — | — | — | — | — | — | — |
| 18 | Vehicle speed sensor | — | W37 | — | 0.5 | SL8-A-20 | — | — | — |
| 19 | Unused cavity | — | — | — | — | — | — | — | — |
| 20 | Sensor voltage 2 | — | W19 | — | 0.5 | SP-5V-1 | — | — | — |
| 21 | Sensor voltage 1 | — | W20 | — | 0.5 | SP-5V-1 | — | — | — |
| 22 | Unused cavity | — | — | — | — | — | — | — | — |
| 23 | Sensor ground 2 | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | Sensor ground 1 | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 25 | Accelerator pedal position B | — | W33 | — | 0.5 | SL8-B-15 | — | — | — |
| 26 | Accelerator pedal position A | — | W32 | — | 0.5 | SL8-B-14 | — | — | — |
| 27 | Unused cavity | — | — | — | — | — | — | — | — |
| 28 | A/F sensor signal − | — | — | — | — | — | — | — | — |
| 29 | Unused cavity | — | — | — | — | — | — | — | — |
| 30 | MAP sensor | — | W26 | — | 0.5 | SL8-B-11 | — | — | — |
| 31 | A/F sensor signal + | — | — | — | — | — | — | — | — |
S2K-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Unused cavity | — | — | — | — | — | — | — | — |
| 2 | Injector 4 | — | W47 | — | 0.5 | SL8-A-4 | — | — | — |
| 3 | Injector 3 | — | W46 | — | 0.5 | SL8-A-3 | — | — | — |
| 4 | Injector 2 | — | W45 | — | 0.5 | SL8-A-2 | — | — | — |
| 5 | Injector 1 | — | W44 | — | 0.5 | SL8-A-1 | — | — | — |
| 6 | VTEC solenoid | — | W54 | — | 0.5 | SL8-A-10 | — | — | — |
| 7 | Unused cavity | — | — | — | — | — | — | — | — |
| 8 | Coolant temp sensor | — | W34 | — | 0.5 | SL8-B-20 | — | — | — |
| 9 | Unused cavity | — | — | — | — | — | — | — | — |
| 10 | Alternator L signal | — | — | — | — | — | — | — | — |
| 11 | VTEC oil pressure switch | — | W38 | — | 0.5 | SL8-A-21 | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Alternator FR signal | — | — | — | — | — | — | — | — |
| 14 | Unused cavity | — | — | — | — | — | — | — | — |
| 15 | Engine mount control solenoid | — | — | — | — | — | — | — | — |
| 16 | Unused cavity | — | — | — | — | — | — | — | — |
| 17 | Intake air temp sensor | — | W35 | — | 0.5 | SL8-B-21 | — | — | — |
| 18 | Alternator control | — | W62 | — | 0.5 | SL8-A-5 | — | — | — |
| 19 | Throttle actuator command to throttle control module (SEFD) | — | — | — | — | — | — | — | — |
| 20 | Throttle actuator command to throttle control module (SEDF) | — | — | — | — | — | — | — | — |
| 21 | Evap canister purge valve | — | W60 | — | 0.5 | SL8-A-17 | — | — | — |
| 22 | Unused cavity | — | — | — | — | — | — | — | — |
| 23 | Unused cavity | — | — | — | — | — | — | — | — |
| 24 | Unused cavity | — | — | — | — | — | — | — | — |
S2K-D
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Cruise set switch | — | — | — | — | — | — | — | — |
| 2 | Unused cavity | — | — | — | — | — | — | — | — |
| 3 | Unused cavity | — | — | — | — | — | — | — | — |
| 4 | Cruise main switch | — | — | — | — | — | — | — | — |
| 5 | Unused cavity | — | — | — | — | — | — | — | — |
| 6 | Unused cavity | — | — | — | — | — | — | — | — |
| 7 | Cruise resume switch | — | — | — | — | — | — | — | — |
| 8 | Brake pedal position switch | — | W39 | — | 0.5 | SL8-A-22 | — | — | — |
| 9 | Cruise clutch signal | — | W40 | — | 0.5 | SL8-A-23 | — | — | — |
| 10 | Unused cavity | — | — | — | — | — | — | — | — |
| 11 | Unused cavity | — | — | — | — | — | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Unused cavity | — | — | — | — | — | — | — | — |
| 14 | Unused cavity | — | — | — | — | — | — | — | — |
| 15 | Throttle actuator relay | — | — | — | — | — | — | — | — |
| 16 | Unused cavity | — | — | — | — | — | — | — | — |
| 17 | Unused cavity | — | — | — | — | — | — | — | — |
S2K-E
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Coolant temp sensor 2 | — | — | — | — | — | — | — | — |
| 2 | Unused cavity | — | — | — | — | — | — | — | — |
| 3 | Logic ground 3 | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 4 | Sensor ground 3 | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 5 | Sensor voltage 3 | — | W21 | — | 0.5 | SP-5V-1 | — | — | — |
| 6 | Unused cavity | — | — | — | — | — | — | — | — |
| 7 | Main relay control | — | W61 | — | 0.5 | SL8-B-3 | — | — | — |
| 8 | A/F sensor heater relay | — | — | — | — | — | — | — | — |
| 9 | Ignition signal | — | W5 | — | 0.5 | SL8-B-4 | — | — | — |
| 10 | Unused cavity | — | — | — | — | — | — | — | — |
| 11 | CAN H | — | W42 | — | 0.5 | SL8-B-27 | — | — | — |
| 12 | Radiator fan control | — | W56 | — | 0.5 | SL8-A-12 | — | — | — |
| 13 | Multiplex communication | — | — | — | — | — | — | — | — |
| 14 | Fuel tank pressure sensor | — | — | — | — | — | — | — | — |
| 15 | Electrical load detector | — | — | — | — | — | — | — | — |
| 16 | Power steering load detector | — | W31 | — | 0.5 | SL8-B-19 | — | — | — |
| 17 | Fuel pump relay | — | W55 | — | 0.5 | SL8-A-11 | — | — | — |
| 18 | A/C clutch relay | — | W57 | — | 0.5 | SL8-A-14 | — | — | — |
| 19 | Evap canister vent shut valve | — | W64 | — | 0.5 | SL8-A-7 | — | — | — |
| 20 | Secondary O2 sensor | — | W36 | — | 0.5 | SL8-B-22 | — | — | — |
| 21 | Secondary O2 heater | — | W63 | — | 0.5 | SL8-A-6 | — | — | — |
| 22 | Brake pedal switch | — | — | — | — | — | — | — | — |
| 23 | Unused cavity | — | — | — | — | — | — | — | — |
| 24 | CAN L | — | W43 | — | 0.5 | SL8-B-28 | — | — | — |
| 25 | Engine speed pulse (tacho) | — | W58 | — | 0.5 | SL8-A-15 | — | — | — |
| 26 | Vehicle speed output | — | W59 | — | 0.5 | SL8-A-16 | — | — | — |
| 27 | Immobilizer code | — | — | — | — | — | — | — | — |
| 28 | A/C switch signal | — | W41 | — | 0.5 | SL8-A-24 | — | — | — |
| 29 | Service check signal | — | — | — | — | — | — | — | — |
| 30 | Write enable signal | — | — | — | — | — | — | — | — |
| 31 | Unused cavity | — | — | — | — | — | — | — | — |
SL8-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injection channel 1 | — | W44 | — | 0.5 | S2K-B-5 | — | — | — |
| 2 | Injection channel 2 | — | W45 | — | 0.5 | S2K-B-4 | — | — | — |
| 3 | Injection channel 3 | — | W46 | — | 0.5 | S2K-B-3 | — | — | — |
| 4 | Injection channel 4 | — | W47 | — | 0.5 | S2K-B-2 | — | — | — |
| 5 | Injection channel 5 | — | W62 | — | 0.5 | S2K-B-18 | — | — | — |
| 6 | Injection channel 6 | — | W63 | — | 0.5 | S2K-E-21 | — | — | — |
| 7 | Injection channel 7 | — | W64 | — | 0.5 | S2K-E-19 | — | — | — |
| 8 | Injection channel 8 | — | — | — | — | — | — | — | — |
| 9 | Sensor supply 8V | — | — | — | — | — | — | — | — |
| 10 | Auxiliary output 1 | — | W54 | — | 0.5 | S2K-B-6 | — | — | — |
| 11 | Auxiliary output 2 | — | W55 | — | 0.5 | S2K-E-17 | — | — | — |
| 12 | Auxiliary output 3 | — | W56 | — | 0.5 | S2K-E-12 | — | — | — |
| 13 | Auxiliary output 4 | — | — | — | — | — | — | — | — |
| 14 | Auxiliary output 5 | — | W57 | — | 0.5 | S2K-E-18 | — | — | — |
| 15 | Auxiliary output 6 | — | W58 | — | 0.5 | S2K-E-25 | — | — | — |
| 16 | Auxiliary output 7 | — | W59 | — | 0.5 | S2K-E-26 | — | — | — |
| 17 | Auxiliary output 8 | — | W60 | — | 0.5 | S2K-B-21 | — | — | — |
| 18 | Auxiliary output 9 | — | W52 | — | 0.5 | TB-J-M+ | — | — | — |
| 19 | Auxiliary output 10 | — | W53 | — | 0.5 | TB-J-M- | — | — | — |
| 20 | Digital input 1 | — | W37 | — | 0.5 | S2K-A-18 | — | — | — |
| 21 | Digital input 2 | — | W38 | — | 0.5 | S2K-B-11 | — | — | — |
| 22 | Digital input 3 | — | W39 | — | 0.5 | S2K-D-8 | — | — | — |
| 23 | Digital input 4 | — | W40 | — | 0.5 | S2K-D-9 | — | — | — |
| 24 | Digital input 5 | — | W41 | — | 0.5 | S2K-E-28 | — | — | — |
| 25 | Digital input 6 | — | — | — | — | — | — | — | — |
| 26 | Ignition channel 1 | — | W48 | — | 0.5 | S2K-A-16 | — | — | — |
| 27 | Ignition channel 2 | — | W49 | — | 0.5 | S2K-A-15 | — | — | — |
| 28 | Ignition channel 3 | — | W50 | — | 0.5 | S2K-A-14 | — | — | — |
| 29 | Ignition channel 4 | — | W51 | — | 0.5 | S2K-A-13 | — | — | — |
| 30 | Ignition channel 5 | — | — | — | — | — | — | — | — |
| 31 | Ignition channel 6 | — | — | — | — | — | — | — | — |
| 32 | Ignition channel 7 | — | — | — | — | — | — | — | — |
| 33 | Ignition channel 8 | — | — | — | — | — | — | — | — |
| 34 | Aux 9–10 14V supply | — | W4 | — | 0.85 | SP-14V-1 | — | — | — |
SL8-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | ECU 14V supply | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 2 | Sensor supply Vref1 5.0V | — | W22 | — | 0.5 | SP-5V-1 | — | — | — |
| 3 | EFI relay output (low side, 200 mA) | — | W61 | — | 0.5 | S2K-E-7 | — | — | — |
| 4 | Ignition switch input | — | W5 | — | 0.5 | S2K-E-9 | — | — | — |
| 5 | Crank index sensor + | — | W23 | — | 0.5 | S2K-A-7 | — | — | — |
| 6 | Crank index sensor − | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 7 | Sync sensor + | — | W24 | — | 0.5 | S2K-A-6 | — | — | — |
| 8 | Sync sensor − | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 9 | Shield (crank/sync/knock) | — | — | — | — | — | — | — | — |
| 10 | Analog sensor 0V reference | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 11 | Analog input 1 | — | W26 | — | 0.5 | S2K-A-30 | — | — | — |
| 12 | Analog input 2 | — | W28 | — | 0.5 | TB-J-TPS1 | — | — | — |
| 13 | Analog input 3 | — | W29 | — | 0.5 | TB-J-TPS2 | — | — | — |
| 14 | Analog input 4 | — | W32 | — | 0.5 | S2K-A-26 | — | — | — |
| 15 | Analog input 5 | — | W33 | — | 0.5 | S2K-A-25 | — | — | — |
| 16 | Knock 1 + | — | W25 | — | 0.5 | S2K-A-1 | — | — | — |
| 17 | Knock 1 − | — | — | — | — | — | — | — | — |
| 18 | ECU ground | — | W11 | — | 0.85 | SP-GND-1 | — | — | — |
| 19 | Analog input 6 | — | W31 | — | 0.5 | S2K-E-16 | — | — | — |
| 20 | Analog input 7 (switchable 1k pull-up) | — | W34 | — | 0.5 | S2K-B-8 | — | — | — |
| 21 | Analog input 8 (switchable 1k pull-up) | — | W35 | — | 0.5 | S2K-B-17 | — | — | — |
| 22 | Analog input 9 (switchable 1k pull-up) | — | W36 | — | 0.5 | S2K-E-20 | — | — | — |
| 23 | Analog input 10 (switchable 1k pull-up) | — | — | — | — | — | — | — | — |
| 24 | Knock 2 + | — | — | — | — | — | — | — | — |
| 25 | Knock 2 − | — | — | — | — | — | — | — | — |
| 26 | ECU ground | — | W12 | — | 0.85 | SP-GND-1 | — | — | — |
| 27 | CAN 1 H | — | W42 | — | 0.5 | S2K-E-11 | — | — | — |
| 28 | CAN 1 L | — | W43 | — | 0.5 | S2K-E-24 | — | — | — |
| 29 | NC | — | — | — | — | — | — | — | — |
| 30 | NC | — | — | — | — | — | — | — | — |
| 31 | Ethernet Tx + | — | — | — | — | — | — | — | — |
| 32 | Ethernet Tx − | — | — | — | — | — | — | — | — |
| 33 | Ethernet Rx + | — | — | — | — | — | — | — | — |
| 34 | Ethernet Rx − | — | — | — | — | — | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W17 | — | 0.5 | SL8-B-6 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | S2K-A-23 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | S2K-A-24 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | S2K-E-4 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | SL8-B-10 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | SL8-B-8 | — | — | — |
| 1 | — | — | W30 | — | 0.5 | TB-J-GND | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W2 | — | 0.85 | S2K-A-3 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | SL8-B-1 | — | — | — |
| 1 | — | — | W1 | — | 0.85 | S2K-A-2 | — | — | — |
| 1 | — | — | W4 | — | 0.85 | SL8-A-34 | — | — | — |
SP-5V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W19 | — | 0.5 | S2K-A-20 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | S2K-A-21 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | S2K-E-5 | — | — | — |
| 1 | — | — | W22 | — | 0.5 | SL8-B-2 | — | — | — |
| 1 | — | — | W27 | — | 0.5 | TB-J-VCC | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W8 | — | 0.85 | S2K-A-8 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | S2K-A-4 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | S2K-A-5 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | S2K-A-9 | — | — | — |
| 1 | — | — | W10 | — | 0.85 | S2K-E-3 | — | — | — |
| 1 | — | — | W11 | — | 0.85 | SL8-B-18 | — | — | — |
| 1 | — | — | W12 | — | 0.85 | SL8-B-26 | — | — | — |
TB-J
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| M+ | Throttle motor + | — | W52 | — | 0.5 | SL8-A-18 | — | — | — |
| M- | Throttle motor − | — | W53 | — | 0.5 | SL8-A-19 | — | — | — |
| VCC | Throttle sensor 5V supply | — | W27 | — | 0.5 | SP-5V-1 | — | — | — |
| TPS1 | Throttle position 1 | — | W28 | — | 0.5 | SL8-B-12 | — | — | — |
| TPS2 | Throttle position 2 | — | W29 | — | 0.5 | SL8-B-13 | — | — | — |
| GND | Throttle sensor ground | — | W30 | — | 0.5 | SP-0V-1 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| S2K-A-1 | Knock sensor | knock_in | SL8-B-16 | Knock 1 + | knock_in | single_source | |
| S2K-A-10 | A/F sensor heater | low_side_out | — | — | — | single_source | |
| S2K-A-11 | Unused cavity | — | — | — | — | unverified | |
| S2K-A-12 | Unused cavity | — | — | — | — | unverified | |
| S2K-A-13 | Ignition coil 4 | ignition_out | SL8-A-29 | Ignition channel 4 | ignition_out | single_source | |
| S2K-A-14 | Ignition coil 3 | ignition_out | SL8-A-28 | Ignition channel 3 | ignition_out | single_source | |
| S2K-A-15 | Ignition coil 2 | ignition_out | SL8-A-27 | Ignition channel 2 | ignition_out | single_source | |
| S2K-A-16 | Ignition coil 1 | ignition_out | SL8-A-26 | Ignition channel 1 | ignition_out | single_source | |
| S2K-A-17 | Unused cavity | — | — | — | — | unverified | |
| S2K-A-18 | Vehicle speed sensor | digital_in | SL8-A-20 | Digital input 1 | digital_in | single_source | |
| S2K-A-19 | Unused cavity | — | — | — | — | unverified | |
| S2K-A-2 | Ignition power 2 | power_in | SL8-A-34 + SL8-B-1 | Aux 9–10 14V supply + ECU 14V supply | power_in | single_source | |
| S2K-A-20 | Sensor voltage 2 | vref | SL8-B-2 + TB-J-VCC | Sensor supply Vref1 5.0V + Throttle sensor 5V supply | power_in + vref | corroborated | |
| S2K-A-21 | Sensor voltage 1 | vref | SL8-B-2 + TB-J-VCC | Sensor supply Vref1 5.0V + Throttle sensor 5V supply | power_in + vref | single_source | |
| S2K-A-22 | Unused cavity | — | — | — | — | unverified | |
| S2K-A-23 | Sensor ground 2 | sensor_ground | SL8-B-10 + SL8-B-6 + SL8-B-8 + TB-J-GND | Analog sensor 0V reference + Crank index sensor − + Sync sensor − + Throttle sensor ground | sensor_ground + trigger_in | corroborated | |
| S2K-A-24 | Sensor ground 1 | sensor_ground | SL8-B-10 + SL8-B-6 + SL8-B-8 + TB-J-GND | Analog sensor 0V reference + Crank index sensor − + Sync sensor − + Throttle sensor ground | sensor_ground + trigger_in | single_source | |
| S2K-A-25 | Accelerator pedal position B | analog_in | SL8-B-15 | Analog input 5 | analog_in | corroborated | |
| S2K-A-26 | Accelerator pedal position A | analog_in | SL8-B-14 | Analog input 4 | analog_in | corroborated | |
| S2K-A-27 | Unused cavity | — | — | — | — | unverified | |
| S2K-A-28 | A/F sensor signal − | — | — | — | — | single_source | |
| S2K-A-29 | Unused cavity | — | — | — | — | unverified | |
| S2K-A-3 | Ignition power 1 | power_in | SL8-A-34 + SL8-B-1 | Aux 9–10 14V supply + ECU 14V supply | power_in | single_source | |
| S2K-A-30 | MAP sensor | analog_in | SL8-B-11 | Analog input 1 | analog_in | single_source | |
| S2K-A-31 | A/F sensor signal + | — | — | — | — | single_source | |
| S2K-A-4 | Power ground 2 | ground | SL8-B-18 + SL8-B-26 | ECU ground + ECU ground | ground | single_source | |
| S2K-A-5 | Power ground 1 | ground | SL8-B-18 + SL8-B-26 | ECU ground + ECU ground | ground | single_source | |
| S2K-A-6 | Cam position sensor (T2) | trigger_in | SL8-B-7 | Sync sensor + | trigger_in | single_source | |
| S2K-A-7 | Crank position sensor (T1) | trigger_in | SL8-B-5 | Crank index sensor + | trigger_in | single_source | |
| S2K-A-8 | Logic ground 2 | ground | SL8-B-18 + SL8-B-26 | ECU ground + ECU ground | ground | single_source | |
| S2K-A-9 | Logic ground 1 | ground | SL8-B-18 + SL8-B-26 | ECU ground + ECU ground | ground | single_source | |
| S2K-B-1 | Unused cavity | — | — | — | — | unverified | |
| S2K-B-10 | Alternator L signal | — | — | — | — | single_source | |
| S2K-B-11 | VTEC oil pressure switch | digital_in | SL8-A-21 | Digital input 2 | digital_in | single_source | |
| S2K-B-12 | Unused cavity | — | — | — | — | unverified | |
| S2K-B-13 | Alternator FR signal | analog_in | — | — | — | single_source | |
| S2K-B-14 | Unused cavity | — | — | — | — | unverified | |
| S2K-B-15 | Engine mount control solenoid | low_side_out | — | — | — | single_source | |
| S2K-B-16 | Unused cavity | — | — | — | — | unverified | |
| S2K-B-17 | Intake air temp sensor | temp_in | SL8-B-21 | Analog input 8 (switchable 1k pull-up) | analog_in | single_source | |
| S2K-B-18 | Alternator control | low_side_out | SL8-A-5 | Injection channel 5 | injector_out | single_source | |
| S2K-B-19 | Throttle actuator command to throttle control module (SEFD) | — | — | — | — | conflict | |
| S2K-B-2 | Injector 4 | injector_out | SL8-A-4 | Injection channel 4 | injector_out | single_source | |
| S2K-B-20 | Throttle actuator command to throttle control module (SEDF) | — | — | — | — | conflict | |
| S2K-B-21 | Evap canister purge valve | low_side_out | SL8-A-17 | Auxiliary output 8 | switch_out | single_source | |
| S2K-B-22 | Unused cavity | — | — | — | — | unverified | |
| S2K-B-23 | Unused cavity | — | — | — | — | unverified | |
| S2K-B-24 | Unused cavity | — | — | — | — | unverified | |
| S2K-B-3 | Injector 3 | injector_out | SL8-A-3 | Injection channel 3 | injector_out | single_source | |
| S2K-B-4 | Injector 2 | injector_out | SL8-A-2 | Injection channel 2 | injector_out | single_source | |
| S2K-B-5 | Injector 1 | injector_out | SL8-A-1 | Injection channel 1 | injector_out | single_source | |
| S2K-B-6 | VTEC solenoid | high_side_out | SL8-A-10 | Auxiliary output 1 | switch_out | single_source | |
| S2K-B-7 | Unused cavity | — | — | — | — | unverified | |
| S2K-B-8 | Coolant temp sensor | temp_in | SL8-B-20 | Analog input 7 (switchable 1k pull-up) | analog_in | single_source | |
| S2K-B-9 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-1 | Cruise set switch | digital_in | — | — | — | single_source | |
| S2K-D-10 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-11 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-12 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-13 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-14 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-15 | Throttle actuator relay | low_side_out | — | — | — | single_source | |
| S2K-D-16 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-17 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-2 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-3 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-4 | Cruise main switch | digital_in | — | — | — | single_source | |
| S2K-D-5 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-6 | Unused cavity | — | — | — | — | unverified | |
| S2K-D-7 | Cruise resume switch | digital_in | — | — | — | single_source | |
| S2K-D-8 | Brake pedal position switch | digital_in | SL8-A-22 | Digital input 3 | digital_in | single_source | |
| S2K-D-9 | Cruise clutch signal | digital_in | SL8-A-23 | Digital input 4 | digital_in | single_source | |
| S2K-E-1 | Coolant temp sensor 2 | temp_in | — | — | — | single_source | |
| S2K-E-10 | Unused cavity | — | — | — | — | unverified | |
| S2K-E-11 | CAN H | can_h | SL8-B-27 | CAN 1 H | can_h | single_source | |
| S2K-E-12 | Radiator fan control | low_side_out | SL8-A-12 | Auxiliary output 3 | switch_out | single_source | |
| S2K-E-13 | Multiplex communication | serial | — | — | — | single_source | |
| S2K-E-14 | Fuel tank pressure sensor | analog_in | — | — | — | single_source | |
| S2K-E-15 | Electrical load detector | analog_in | — | — | — | single_source | |
| S2K-E-16 | Power steering load detector | analog_in | SL8-B-19 | Analog input 6 | analog_in | corroborated | |
| S2K-E-17 | Fuel pump relay | low_side_out | SL8-A-11 | Auxiliary output 2 | switch_out | single_source | |
| S2K-E-18 | A/C clutch relay | low_side_out | SL8-A-14 | Auxiliary output 5 | switch_out | single_source | |
| S2K-E-19 | Evap canister vent shut valve | low_side_out | SL8-A-7 | Injection channel 7 | injector_out | single_source | |
| S2K-E-2 | Unused cavity | — | — | — | — | unverified | |
| S2K-E-20 | Secondary O2 sensor | lambda_nb_in | SL8-B-22 | Analog input 9 (switchable 1k pull-up) | analog_in | single_source | |
| S2K-E-21 | Secondary O2 heater | low_side_out | SL8-A-6 | Injection channel 6 | injector_out | single_source | |
| S2K-E-22 | Brake pedal switch | digital_in | — | — | — | single_source | |
| S2K-E-23 | Unused cavity | — | — | — | — | unverified | |
| S2K-E-24 | CAN L | can_l | SL8-B-28 | CAN 1 L | can_l | single_source | |
| S2K-E-25 | Engine speed pulse (tacho) | tacho_out | SL8-A-15 | Auxiliary output 6 | switch_out | single_source | |
| S2K-E-26 | Vehicle speed output | tacho_out | SL8-A-16 | Auxiliary output 7 | switch_out | single_source | |
| S2K-E-27 | Immobilizer code | — | — | — | — | single_source | |
| S2K-E-28 | A/C switch signal | digital_in | SL8-A-24 | Digital input 5 | digital_in | single_source | |
| S2K-E-29 | Service check signal | — | — | — | — | single_source | |
| S2K-E-3 | Logic ground 3 | ground | SL8-B-18 + SL8-B-26 | ECU ground + ECU ground | ground | single_source | |
| S2K-E-30 | Write enable signal | — | — | — | — | single_source | |
| S2K-E-31 | Unused cavity | — | — | — | — | unverified | |
| S2K-E-4 | Sensor ground 3 | sensor_ground | SL8-B-10 + SL8-B-6 + SL8-B-8 + TB-J-GND | Analog sensor 0V reference + Crank index sensor − + Sync sensor − + Throttle sensor ground | sensor_ground + trigger_in | corroborated | |
| S2K-E-5 | Sensor voltage 3 | vref | SL8-B-2 + TB-J-VCC | Sensor supply Vref1 5.0V + Throttle sensor 5V supply | power_in + vref | corroborated | |
| S2K-E-6 | Unused cavity | — | — | — | — | unverified | |
| S2K-E-7 | Main relay control | low_side_out | SL8-B-3 | EFI relay output (low side, 200 mA) | low_side_out | single_source | |
| S2K-E-8 | A/F sensor heater relay | low_side_out | — | — | — | single_source | |
| S2K-E-9 | Ignition signal | digital_in | SL8-B-4 | Ignition switch input | digital_in | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | S2K-A-2 | SP-14V-1 | 0.85 | no route | Ignition power 2 | — | |
| W2 | S2K-A-3 | SP-14V-1 | 0.85 | no route | Ignition power 1 | — | |
| W3 | SP-14V-1 | SL8-B-1 | 0.85 | no route | ECU 14V supply | — | |
| W4 | SP-14V-1 | SL8-A-34 | 0.85 | no route | Aux 9–10 14V supply | — | |
| W5 | S2K-E-9 | SL8-B-4 | 0.5 | no route | Ignition signal | — | |
| W6 | S2K-A-4 | SP-GND-1 | 0.85 | no route | Power ground 2 | — | |
| W7 | S2K-A-5 | SP-GND-1 | 0.85 | no route | Power ground 1 | — | |
| W8 | S2K-A-8 | SP-GND-1 | 0.85 | no route | Logic ground 2 | — | |
| W9 | S2K-A-9 | SP-GND-1 | 0.85 | no route | Logic ground 1 | — | |
| W10 | S2K-E-3 | SP-GND-1 | 0.85 | no route | Logic ground 3 | — | |
| W11 | SP-GND-1 | SL8-B-18 | 0.85 | no route | ECU ground | — | |
| W12 | SP-GND-1 | SL8-B-26 | 0.85 | no route | ECU ground | — | |
| W13 | S2K-A-23 | SP-0V-1 | 0.5 | no route | Sensor ground 2 | — | |
| W14 | S2K-A-24 | SP-0V-1 | 0.5 | no route | Sensor ground 1 | — | |
| W15 | S2K-E-4 | SP-0V-1 | 0.5 | no route | Sensor ground 3 | — | |
| W16 | SP-0V-1 | SL8-B-10 | 0.5 | no route | Analog sensor 0V reference | — | |
| W17 | SP-0V-1 | SL8-B-6 | 0.5 | no route | Crank index sensor − | — | |
| W18 | SP-0V-1 | SL8-B-8 | 0.5 | no route | Sync sensor − | — | |
| W19 | S2K-A-20 | SP-5V-1 | 0.5 | no route | Sensor voltage 2 | — | |
| W20 | S2K-A-21 | SP-5V-1 | 0.5 | no route | Sensor voltage 1 | — | |
| W21 | S2K-E-5 | SP-5V-1 | 0.5 | no route | Sensor voltage 3 | — | |
| W22 | SP-5V-1 | SL8-B-2 | 0.5 | no route | Sensor supply Vref1 5.0V | — | |
| W23 | S2K-A-7 | SL8-B-5 | 0.5 | no route | Crank position sensor (T1) | — | |
| W24 | S2K-A-6 | SL8-B-7 | 0.5 | no route | Cam position sensor (T2) | — | |
| W25 | S2K-A-1 | SL8-B-16 | 0.5 | no route | Knock sensor | — | |
| W26 | S2K-A-30 | SL8-B-11 | 0.5 | no route | MAP sensor | — | |
| W27 | SP-5V-1 | TB-J-VCC | 0.5 | no route | Throttle sensor 5V supply | — | |
| W28 | TB-J-TPS1 | SL8-B-12 | 0.5 | no route | Throttle position 1 | — | |
| W29 | TB-J-TPS2 | SL8-B-13 | 0.5 | no route | Throttle position 2 | — | |
| W30 | TB-J-GND | SP-0V-1 | 0.5 | no route | Throttle sensor ground | — | |
| W31 | S2K-E-16 | SL8-B-19 | 0.5 | no route | Power steering load detector | — | |
| W32 | S2K-A-26 | SL8-B-14 | 0.5 | no route | Accelerator pedal position A | — | |
| W33 | S2K-A-25 | SL8-B-15 | 0.5 | no route | Accelerator pedal position B | — | |
| W34 | S2K-B-8 | SL8-B-20 | 0.5 | no route | Coolant temp sensor | — | |
| W35 | S2K-B-17 | SL8-B-21 | 0.5 | no route | Intake air temp sensor | — | |
| W36 | S2K-E-20 | SL8-B-22 | 0.5 | no route | Secondary O2 sensor | — | |
| W37 | S2K-A-18 | SL8-A-20 | 0.5 | no route | Vehicle speed sensor | — | |
| W38 | S2K-B-11 | SL8-A-21 | 0.5 | no route | VTEC oil pressure switch | — | |
| W39 | S2K-D-8 | SL8-A-22 | 0.5 | no route | Brake pedal position switch | — | |
| W40 | S2K-D-9 | SL8-A-23 | 0.5 | no route | Cruise clutch signal | — | |
| W41 | S2K-E-28 | SL8-A-24 | 0.5 | no route | A/C switch signal | — | |
| W42 | S2K-E-11 | SL8-B-27 | 0.5 | no route | CAN H | — | |
| W43 | S2K-E-24 | SL8-B-28 | 0.5 | no route | CAN L | — | |
| W44 | S2K-B-5 | SL8-A-1 | 0.5 | no route | Injector 1 | — | |
| W45 | S2K-B-4 | SL8-A-2 | 0.5 | no route | Injector 2 | — | |
| W46 | S2K-B-3 | SL8-A-3 | 0.5 | no route | Injector 3 | — | |
| W47 | S2K-B-2 | SL8-A-4 | 0.5 | no route | Injector 4 | — | |
| W48 | S2K-A-16 | SL8-A-26 | 0.5 | no route | Ignition coil 1 | — | |
| W49 | S2K-A-15 | SL8-A-27 | 0.5 | no route | Ignition coil 2 | — | |
| W50 | S2K-A-14 | SL8-A-28 | 0.5 | no route | Ignition coil 3 | — | |
| W51 | S2K-A-13 | SL8-A-29 | 0.5 | no route | Ignition coil 4 | — | |
| W52 | TB-J-M+ | SL8-A-18 | 0.5 | no route | Throttle motor + | — | |
| W53 | TB-J-M- | SL8-A-19 | 0.5 | no route | Throttle motor − | — | |
| W54 | S2K-B-6 | SL8-A-10 | 0.5 | no route | VTEC solenoid | — | |
| W55 | S2K-E-17 | SL8-A-11 | 0.5 | no route | Fuel pump relay | — | |
| W56 | S2K-E-12 | SL8-A-12 | 0.5 | no route | Radiator fan control | — | |
| W57 | S2K-E-18 | SL8-A-14 | 0.5 | no route | A/C clutch relay | — | |
| W58 | S2K-E-25 | SL8-A-15 | 0.5 | no route | Engine speed pulse (tacho) | — | |
| W59 | S2K-E-26 | SL8-A-16 | 0.5 | no route | Vehicle speed output | — | |
| W60 | S2K-B-21 | SL8-A-17 | 0.5 | no route | Evap canister purge valve | — | |
| W61 | S2K-E-7 | SL8-B-3 | 0.5 | no route | Main relay control | — | |
| W62 | S2K-B-18 | SL8-A-5 | 0.5 | no route | Alternator control | — | |
| W63 | S2K-E-21 | SL8-A-6 | 0.5 | no route | Secondary O2 heater | — | |
| W64 | S2K-E-19 | SL8-A-7 | 0.5 | no route | Evap canister vent shut valve | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 4-1437290-0 | TE | Superseal 1.0 34-way plug, Key 1 | 1.000 | ea |
| connector | 4-1437290-1 | TE | Superseal 1.0 34-way plug, Key 2 | 1.000 | ea |
| connector | S2K-0609-ECU-A | Honda | S2000 2006–09 ECU plug A (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-B | Honda | S2000 2006–09 ECU plug B (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-D | Honda | S2000 2006–09 ECU plug D (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-E | Honda | S2000 2006–09 ECU plug E (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-TB | Honda | 2006–09 S2000 throttle body plug, 6-way (pin numbers from Link forum dealer post; housing P/N unknown) | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (18)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | LOAD_CURRENT | SL8-A-18 | SL8-A-18 "Auxiliary output 9" is rated 5.0 A but the load on this net draws 14 A (TB-J-M+ Throttle motor +). |
| error | LOAD_CURRENT | SL8-A-19 | SL8-A-19 "Auxiliary output 10" is rated 5.0 A but the load on this net draws 14 A (TB-J-M- Throttle motor −). |
| warn | DBW_MOTOR_ISOLATION | SL8-A-34 | SL8-A-34 "Aux 9–10 14V supply" is fed from the same net as the ECU main supply (SL8-B-1). Link's S2000 DBW wiring feeds the throttle-motor supply through a separate isolation relay switched by the ECU, so motor power can be cut on a throttle fault. Add one, or confirm SL8 cuts the H-bridge internally. |
| warn | DBW_SHARED_5V | S2K-A-20 + S2K-A-21 + S2K-E-5 + SL8-B-2 + SP-5V-1 + TB-J-VCC | These 5 V supplies are separate in the stock car (S2K-A-20 [s2k_vcc2], S2K-A-21 [s2k_vcc1], S2K-E-5 [s2k_vcc3]) and here share one ECU 5 V (SL8-B-2). On a drive-by-wire car the OEM splits them so one short or fault can't corrupt both throttle/pedal tracks at once. SL8 has 1 5 V sensor supply pin(s). All are in use, so decide: accept the shared supply (and rely on the ECU's DBW fault checks), or add a separate regulated 5 V for the sub tracks. |
| info | NET_FAMILY | S2K-A-23 ↔ SL8-B-6 | S2K-A-23 "Sensor ground 2" [sensor_ground] is wired to SL8-B-6 "Crank index sensor −" [trigger_in]. Trigger return tied to sensor/trigger ground: correct for single-ended trigger inputs. |
| info | NET_FAMILY | S2K-B-17 ↔ SL8-B-21 | S2K-B-17 "Intake air temp sensor" [temp_in] is wired to SL8-B-21 "Analog input 8 (switchable 1k pull-up)" [analog_in]. Thermistor on a plain analog input needs a pull-up; check the channel can enable one. |
| info | NET_FAMILY | S2K-B-18 ↔ SL8-A-5 | S2K-B-18 "Alternator control" [low_side_out] is wired to SL8-A-5 "Injection channel 5" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | S2K-B-21 ↔ SL8-A-17 | S2K-B-21 "Evap canister purge valve" [low_side_out] is wired to SL8-A-17 "Auxiliary output 8" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | S2K-B-6 ↔ SL8-A-10 | S2K-B-6 "VTEC solenoid" [high_side_out] is wired to SL8-A-10 "Auxiliary output 1" [switch_out]. Configure this output as high side. |
| info | NET_FAMILY | S2K-B-8 ↔ SL8-B-20 | S2K-B-8 "Coolant temp sensor" [temp_in] is wired to SL8-B-20 "Analog input 7 (switchable 1k pull-up)" [analog_in]. Thermistor on a plain analog input needs a pull-up; check the channel can enable one. |
| info | NET_FAMILY | S2K-E-12 ↔ SL8-A-12 | S2K-E-12 "Radiator fan control" [low_side_out] is wired to SL8-A-12 "Auxiliary output 3" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | S2K-E-17 ↔ SL8-A-11 | S2K-E-17 "Fuel pump relay" [low_side_out] is wired to SL8-A-11 "Auxiliary output 2" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | S2K-E-18 ↔ SL8-A-14 | S2K-E-18 "A/C clutch relay" [low_side_out] is wired to SL8-A-14 "Auxiliary output 5" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | S2K-E-19 ↔ SL8-A-7 | S2K-E-19 "Evap canister vent shut valve" [low_side_out] is wired to SL8-A-7 "Injection channel 7" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | S2K-E-21 ↔ SL8-A-6 | S2K-E-21 "Secondary O2 heater" [low_side_out] is wired to SL8-A-6 "Injection channel 6" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | S2K-E-25 ↔ SL8-A-15 | S2K-E-25 "Engine speed pulse (tacho)" [tacho_out] is wired to SL8-A-15 "Auxiliary output 6" [switch_out]. Frequency output on a general output: set it up as a tacho/frequency output with the right pull-up. |
| info | NET_FAMILY | S2K-E-26 ↔ SL8-A-16 | S2K-E-26 "Vehicle speed output" [tacho_out] is wired to SL8-A-16 "Auxiliary output 7" [switch_out]. Frequency output on a general output: set it up as a tacho/frequency output with the right pull-up. |
| info | UNMAPPED | OEM | 21 optional OEM pins are not mapped: S2K-A-10 A/F sensor heater; S2K-A-28 A/F sensor signal −; S2K-A-31 A/F sensor signal +; S2K-B-10 Alternator L signal; S2K-B-13 Alternator FR signal; S2K-B-15 Engine mount control solenoid; S2K-B-19 Throttle actuator command to throttle control module (SEFD); S2K-B-20 Throttle actuator command to throttle control module (SEDF); S2K-D-1 Cruise set switch; S2K-D-15 Throttle actuator relay; S2K-D-4 Cruise main switch; S2K-D-7 Cruise resume switch; S2K-E-1 Coolant temp sensor 2; S2K-E-13 Multiplex communication; S2K-E-14 Fuel tank pressure sensor; S2K-E-15 Electrical load detector; S2K-E-22 Brake pedal switch; S2K-E-27 Immobilizer code; S2K-E-29 Service check signal; S2K-E-30 Write enable signal; S2K-E-8 A/F sensor heater relay |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| SUPPLY_GROUP | S2K-A-20 + S2K-A-21 + S2K-E-5 + SL8-B-2 + SP-5V-1 + TB-J-VCC | Emtron has one 5V reference; the OEM ECU's separate 5V supplies are joined. Decision pending (see document). | mapping-proposal |
Notes
Not buildable as wired: the S2000 throttle motor draws ≥ ~14 A at stall (FSM ≤ ~1.0 Ω) and every H-bridge on this ECU is rated 5 A. Use the cable-conversion variant, an Emtron KV (Aux 13–16, 15 A), or an external DBW driver.
Sources
| Reliability | Kind | Title | URL |
|---|---|---|---|
| 4 | vendor_doc | AEM 30-6053 Series 2 Plug & Play EMS, 2006–2008 S2000 AP2 (original ECU pinout) | https://documents.aemelectronics.com/techlibrary_30-6053_series_2_plug___play_ems.pdf |
| 4 | datasheet | Emtron SL4/SL6/SL8 ECU datasheets | https://docs.emtronaustralia.com.au/engine-management/datasheets/index.html |
| 4 | vendor_doc | Emtron SL4/SL6/SL8 pinout pages | https://docs.emtronaustralia.com.au/engine-management/wiring/index.html |
| 4 | service_manual | Honda S2000 Service Manual 2000–2008 (DBW engine control) | https://www.s2000.wiki/view/images/7/7f/Service_Manual_2000-2008.pdf |
| 3 | vendor_doc | ScienceofSpeed Link G4X ECU, S2000 2006–09 (product page) | https://www.scienceofspeed.com/s2000-2000-09/scienceofspeed-link-g4x-ecu-s2000-2006-09-enpp-3822.html |
| 2 | forum | Link forum: dbw wiring (07/08 S2000, ViPEC V88) | https://forums.linkecu.com/topic/313-dbw-wiring/ |