BMW 3 Series E46 1998–2006 (M54) → AMP EFI MS3Pro EVO+ (auto)
BMW 3 Series E46 1998–2006 (M54) — AMP EFI — MS3Pro EVO+
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-08
Before you start
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | none |
| Size of the job | 86 wires · 13 connectors · 1 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-X60001-8 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-X60001-9 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | MS3PROEVO-A-35 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-X60001-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-X60001-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-X60001-6 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-X60005-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | SP-GND-1 | MS3PROEVO-B-3 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | MS3PROEVO-B-5 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | SP-GND-1 | MS3PROEVO-B-7 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | SP-GND-1 | MS3PROEVO-B-9 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-X60002-20 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-X60002-21 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-X60002-22 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-X60002-24 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-X60003-15 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-X60003-17 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-X60003-18 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-X60003-20 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-X60003-21 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-X60003-23 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-X60003-25 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-X60003-28 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-X60004-12 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-X60004-7 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | SP-0V-1 | MS3PROEVO-A-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | SP-0V-1 | MS3PROEVO-A-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | SP-0V-1 | MS3PROEVO-C-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | SP-0V-1 | MS3PROEVO-C-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | SP-0V-1 | MS3PROEVO-C-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | SP-0V-1 | MS3PROEVO-C-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | SP-0V-1 | MS3PROEVO-C-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-X60003-7 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-X60004-14 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-X60004-9 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | SP-5V1-1 | MS3PROEVO-A-8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-X60003-8 | MS3PROEVO-A-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | SP-0V-1 | MS3PROEVO-A-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-X60003-2 | MS3PROEVO-A-26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | SP-0V-1 | MS3PROEVO-A-27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-X60003-5 | MS3PROEVO-B-34 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | SP-0V-1 | MS3PROEVO-B-35 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-X60003-29 | MS3PROEVO-A-31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-X60003-30 | MS3PROEVO-A-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-X60005-3 | MS3PROEVO-B-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-X60005-2 | MS3PROEVO-B-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | OEM-X60005-1 | MS3PROEVO-B-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | OEM-X60005-9 | MS3PROEVO-B-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W49 | OEM-X60005-8 | MS3PROEVO-B-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W50 | OEM-X60005-7 | MS3PROEVO-B-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W51 | OEM-X60003-33 | MS3PROEVO-A-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W52 | OEM-X60003-34 | MS3PROEVO-A-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W53 | OEM-X60003-35 | MS3PROEVO-B-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W54 | OEM-X60003-36 | MS3PROEVO-B-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W55 | OEM-X60003-37 | MS3PROEVO-B-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W56 | OEM-X60003-38 | MS3PROEVO-B-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W57 | OEM-X60003-48 | SP-SHD-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W58 | SP-SHD-1 | MS3PROEVO-A-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W59 | OEM-X60003-43 | MS3PROEVO-B-30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W60 | OEM-X60003-44 | MS3PROEVO-B-31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W61 | OEM-X60003-46 | MS3PROEVO-B-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W62 | OEM-X60003-47 | MS3PROEVO-B-33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W63 | OEM-X60001-1 | MS3PROEVO-A-28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W64 | OEM-X60002-23 | MS3PROEVO-A-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W65 | OEM-X60004-10 | MS3PROEVO-C-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W66 | OEM-X60002-1 | MS3PROEVO-A-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W67 | OEM-X60002-13 | MS3PROEVO-C-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W68 | OEM-X60002-19 | MS3PROEVO-A-30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W69 | OEM-X60002-7 | MS3PROEVO-C-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W70 | OEM-X60003-40 | MS3PROEVO-C-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W71 | OEM-X60003-41 | MS3PROEVO-A-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W72 | OEM-X60003-42 | MS3PROEVO-A-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W73 | OEM-X60003-45 | MS3PROEVO-A-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W74 | OEM-X60003-49 | MS3PROEVO-B-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W75 | OEM-X60003-1 | MS3PROEVO-A-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W76 | OEM-X60003-19 | MS3PROEVO-A-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W77 | OEM-X60004-8 | MS3PROEVO-A-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W78 | OEM-X60003-10 | MS3PROEVO-A-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W79 | OEM-X60004-13 | MS3PROEVO-A-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W80 | OEM-X60002-14 | MS3PROEVO-A-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W81 | OEM-X60002-15 | MS3PROEVO-A-23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W82 | OEM-X60002-16 | MS3PROEVO-A-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W83 | OEM-X60002-18 | MS3PROEVO-A-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W84 | OEM-X60003-24 | MS3PROEVO-A-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W85 | OEM-X60003-22 | MS3PROEVO-A-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W86 | OEM-X60003-27 | MS3PROEVO-C-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | MS3PROEVO-A-35 | MS3PROEVO-A-13 | open (OL) | +12 V supply must not touch sensor ground | |
| 2 | MS3PROEVO-A-13 | MS3PROEVO-A-8 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 3 | MS3PROEVO-A-35 | MS3PROEVO-A-8 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 4 | MS3PROEVO-B-3 | MS3PROEVO-A-35 | open (OL) | power ground must not touch +12 V supply | |
| 5 | MS3PROEVO-B-3 | MS3PROEVO-A-8 | open (OL) | power ground must not touch 5 V sensor reference |
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
MS3PROEVO-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | High current out 1 | — | W71 | — | 0.5 | OEM-X60003-41 | — | — | — |
| 10 | MAT in | — | W84 | — | 0.5 | OEM-X60003-24 | — | — | — |
| 11 | CLT in | — | W85 | — | 0.5 | OEM-X60003-22 | — | — | — |
| 12 | Analog In 6 | — | W82 | — | 0.5 | OEM-X60002-16 | — | — | — |
| 13 | Logic Ground | — | W26 | — | 0.5 | SP-0V-1 | — | — | — |
| 14 | PWM / Idle Out 1 | — | W64 | — | 0.5 | OEM-X60002-23 | — | — | — |
| 15 | CKP− | — | W38 | — | 0.5 | SP-0V-1 | — | — | — |
| 16 | Ground Shield Drain | — | W58 | — | 0.5 | SP-SHD-1 | — | — | — |
| 17 | Analog In 7 | — | W83 | — | 0.5 | OEM-X60002-18 | — | — | — |
| 18 | Sensor return | — | W27 | — | 0.5 | SP-0V-1 | — | — | — |
| 19 | Analog in 1 | — | W75 | — | 0.5 | OEM-X60003-1 | — | — | — |
| 2 | High current out 2 | — | W72 | — | 0.5 | OEM-X60003-42 | — | — | — |
| 20 | Analog in 2 | — | W77 | — | 0.5 | OEM-X60004-8 | — | — | — |
| 21 | Analog in 3 | — | W78 | — | 0.5 | OEM-X60003-10 | — | — | — |
| 22 | Analog In 4 | — | W79 | — | 0.5 | OEM-X60004-13 | — | — | — |
| 23 | Analog In 5 | — | W81 | — | 0.5 | OEM-X60002-15 | — | — | — |
| 24 | Tach out | — | — | — | — | — | — | — | — |
| 25 | O2 in | — | W80 | — | 0.5 | OEM-X60002-14 | — | — | — |
| 26 | CMP+ | — | W39 | — | 0.5 | OEM-X60003-2 | — | — | — |
| 27 | CMP− | — | W40 | — | 0.5 | SP-0V-1 | — | — | — |
| 28 | Fuel pump relay out | — | W63 | — | 0.5 | OEM-X60001-1 | — | — | — |
| 29 | PWM out 2 | — | W66 | — | 0.5 | OEM-X60002-1 | — | — | — |
| 3 | Injector out J | — | W51 | — | 0.5 | OEM-X60003-33 | — | — | — |
| 30 | PWM out 3 | — | W68 | — | 0.5 | OEM-X60002-19 | — | — | — |
| 31 | Knock in 1 | — | W43 | — | 0.5 | OEM-X60003-29 | — | — | — |
| 32 | Digital switched in 1 | — | — | — | — | — | — | — | — |
| 33 | CAN L | — | — | — | — | — | — | — | — |
| 34 | CAN H | — | — | — | — | — | — | — | — |
| 35 | 12V+ switched power in | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 4 | Injector out I | — | W52 | — | 0.5 | OEM-X60003-34 | — | — | — |
| 5 | High current out 3 | — | W73 | — | 0.5 | OEM-X60003-45 | — | — | — |
| 6 | CKP+ | — | W37 | — | 0.5 | OEM-X60003-8 | — | — | — |
| 7 | Knock In 2 | — | W44 | — | 0.5 | OEM-X60003-30 | — | — | — |
| 8 | 5V+ VREF out | — | W36 | — | 0.5 | SP-5V1-1 | — | — | — |
| 9 | TPS in | — | W76 | — | 0.5 | OEM-X60003-19 | — | — | — |
MS3PROEVO-B
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector out A | — | W53 | — | 0.5 | OEM-X60003-35 | — | — | — |
| 10 | Injector out F | — | W54 | — | 0.5 | OEM-X60003-36 | — | — | — |
| 11 | Injector out G | — | W55 | — | 0.5 | OEM-X60003-37 | — | — | — |
| 12 | Injector out H | — | W56 | — | 0.5 | OEM-X60003-38 | — | — | — |
| 13 | Spark out G | — | W45 | — | 0.5 | OEM-X60005-3 | — | — | — |
| 14 | Spark out E | — | W46 | — | 0.5 | OEM-X60005-2 | — | — | — |
| 15 | Spark out C | — | W47 | — | 0.5 | OEM-X60005-1 | — | — | — |
| 16 | Spark out H | — | W48 | — | 0.5 | OEM-X60005-9 | — | — | — |
| 17 | Digital frequency in 2 (Hall) | — | — | — | — | — | — | — | — |
| 18 | Ground Shield Drain | — | — | — | — | — | — | — | — |
| 19 | Digital switched 12V in | — | — | — | — | — | — | — | — |
| 2 | Injector out B | — | W74 | — | 0.5 | OEM-X60003-49 | — | — | — |
| 20 | Digital switched in 2 | — | — | — | — | — | — | — | — |
| 21 | Digital frequency in 3 (unconditioned) | — | — | — | — | — | — | — | — |
| 22 | Digital Frequency in 3 (VR+) | — | — | — | — | — | — | — | — |
| 23 | Digital Frequency In 3 (VR−) | — | — | — | — | — | — | — | — |
| 24 | Spark out F | — | W49 | — | 0.5 | OEM-X60005-8 | — | — | — |
| 25 | Spark out B | — | W50 | — | 0.5 | OEM-X60005-7 | — | — | — |
| 26 | Spark out D | — | — | — | — | — | — | — | — |
| 27 | Spark out A | — | — | — | — | — | — | — | — |
| 28 | Digital frequency in 1 (unconditioned) | — | — | — | — | — | — | — | — |
| 29 | Digital switched in 3 | — | — | — | — | — | — | — | — |
| 3 | Ground | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 30 | Stepper IAC out 1B | — | W59 | — | 0.5 | OEM-X60003-43 | — | — | — |
| 31 | Stepper IAC out 1A | — | W60 | — | 0.5 | OEM-X60003-44 | — | — | — |
| 32 | Stepper IAC out 2A | — | W61 | — | 0.5 | OEM-X60003-46 | — | — | — |
| 33 | Stepper IAC out 2B | — | W62 | — | 0.5 | OEM-X60003-47 | — | — | — |
| 34 | Digital Frequency in 1 (VR+) | — | W41 | — | 0.5 | OEM-X60003-5 | — | — | — |
| 35 | Digital Frequency in 1 (VR−) | — | W42 | — | 0.5 | SP-0V-1 | — | — | — |
| 4 | Injector out C | — | — | — | — | — | — | — | — |
| 5 | Ground | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Injector out D | — | — | — | — | — | — | — | — |
| 7 | Ground | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 8 | Injector out E | — | — | — | — | — | — | — | — |
| 9 | Ground | — | W11 | — | 0.85 | SP-GND-1 | — | — | — |
MS3PROEVO-C
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | PWM out 5 | — | W70 | — | 0.5 | OEM-X60003-40 | — | — | — |
| 10 | Digital switched in 5 | — | — | — | — | — | — | — | — |
| 11 | Digital switched in 4 | — | — | — | — | — | — | — | — |
| 12 | Digital I/O 5 | — | — | — | — | — | — | — | — |
| 13 | Digital I/O 3 | — | — | — | — | — | — | — | — |
| 14 | Digital I/O 1 | — | — | — | — | — | — | — | — |
| 15 | 5V+ VREF out 2 | — | — | — | — | — | — | — | — |
| 17 | Sensor return | — | W28 | — | 0.5 | SP-0V-1 | — | — | — |
| 18 | Sensor return | — | W29 | — | 0.5 | SP-0V-1 | — | — | — |
| 19 | Sensor return | — | W30 | — | 0.5 | SP-0V-1 | — | — | — |
| 2 | PWM out 4 | — | W69 | — | 0.5 | OEM-X60002-7 | — | — | — |
| 20 | Sensor return | — | W31 | — | 0.5 | SP-0V-1 | — | — | — |
| 21 | Sensor return | — | W32 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | 5V+ VREF out 1 | — | — | — | — | — | — | — | — |
| 3 | Digital out 2 | — | W67 | — | 0.5 | OEM-X60002-13 | — | — | — |
| 4 | Digital out 1 | — | W65 | — | 0.5 | OEM-X60004-10 | — | — | — |
| 5 | Digital I/O 4 | — | — | — | — | — | — | — | — |
| 6 | Digital I/O 2 | — | — | — | — | — | — | — | — |
| 7 | Analog in 8 | — | W86 | — | 0.5 | OEM-X60003-27 | — | — | — |
OEM-X60001
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector/unloader relay control (terminal 15) | — | W63 | — | 0.5 | MS3PROEVO-A-28 | — | — | — |
| 4 | Power ground | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | Power ground | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Power ground | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 7 | Battery constant (terminal 30) | — | — | — | — | — | — | — | — |
| 8 | ECU main power (terminal 87 via main relay) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 9 | Voltage supply (injector / fuse carrier) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
OEM-X60002
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | O2 sensor heater, bank 1 pre-cat | — | W66 | — | 0.5 | MS3PROEVO-A-29 | — | — | — |
| 13 | O2 sensor heater, bank 2 pre-cat | — | W67 | — | 0.5 | MS3PROEVO-C-3 | — | — | — |
| 14 | O2 sensor signal, bank 1 pre-cat | — | W80 | — | 0.5 | MS3PROEVO-A-25 | — | — | — |
| 15 | O2 sensor signal, bank 2 pre-cat | — | W81 | — | 0.5 | MS3PROEVO-A-23 | — | — | — |
| 16 | O2 sensor signal, bank 1 post-cat | — | W82 | — | 0.5 | MS3PROEVO-A-12 | — | — | — |
| 18 | O2 sensor signal, bank 2 post-cat | — | W83 | — | 0.5 | MS3PROEVO-A-17 | — | — | — |
| 19 | O2 sensor heater, bank 2 post-cat | — | W68 | — | 0.5 | MS3PROEVO-A-30 | — | — | — |
| 20 | O2 sensor ground, bank 1 pre-cat | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| 21 | O2 sensor ground, bank 2 pre-cat | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | O2 sensor ground, bank 1 post-cat | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 23 | Main relay control | — | W64 | — | 0.5 | MS3PROEVO-A-14 | — | — | — |
| 24 | O2 sensor ground, bank 2 post-cat | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 7 | O2 sensor heater, bank 1 post-cat | — | W69 | — | 0.5 | MS3PROEVO-C-2 | — | — | — |
OEM-X60003
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Mass air flow (MAF) signal | — | W75 | — | 0.5 | MS3PROEVO-A-19 | — | — | — |
| 10 | Throttle position sensor 2 | — | W78 | — | 0.5 | MS3PROEVO-A-21 | — | — | — |
| 15 | Exhaust camshaft ground | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 17 | MAF ground | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 18 | Intake camshaft ground | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 19 | Throttle position sensor 1 | — | W76 | — | 0.5 | MS3PROEVO-A-9 | — | — | — |
| 2 | Exhaust camshaft position | — | W39 | — | 0.5 | MS3PROEVO-A-26 | — | — | — |
| 20 | Throttle ground | — | W19 | — | 0.5 | SP-0V-1 | — | — | — |
| 21 | Crankshaft ground | — | W20 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | Intake air temperature (IAT) | — | W85 | — | 0.5 | MS3PROEVO-A-11 | — | — | — |
| 23 | IAT ground | — | W21 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | Engine coolant temperature (ECT) | — | W84 | — | 0.5 | MS3PROEVO-A-10 | — | — | — |
| 25 | ECT ground | — | W22 | — | 0.5 | SP-0V-1 | — | — | — |
| 27 | Engine oil temperature | — | W86 | — | 0.5 | MS3PROEVO-C-7 | — | — | — |
| 28 | Oil temperature ground | — | W23 | — | 0.5 | SP-0V-1 | — | — | — |
| 29 | Knock sensor, cylinders 1-3 (A) | — | W43 | — | 0.5 | MS3PROEVO-A-31 | — | — | — |
| 30 | Knock sensor, cylinders 1-3 (B) | — | W44 | — | 0.5 | MS3PROEVO-A-7 | — | — | — |
| 31 | Knock sensor, cylinders 4-6 (A) | — | — | — | — | — | — | — | — |
| 32 | Knock sensor, cylinders 4-6 (B) | — | — | — | — | — | — | — | — |
| 33 | Injector cylinder 1 | — | W51 | — | 0.5 | MS3PROEVO-A-3 | — | — | — |
| 34 | Injector cylinder 2 | — | W52 | — | 0.5 | MS3PROEVO-A-4 | — | — | — |
| 35 | Injector cylinder 3 | — | W53 | — | 0.5 | MS3PROEVO-B-1 | — | — | — |
| 36 | Injector cylinder 4 | — | W54 | — | 0.5 | MS3PROEVO-B-10 | — | — | — |
| 37 | Injector cylinder 5 | — | W55 | — | 0.5 | MS3PROEVO-B-11 | — | — | — |
| 38 | Injector cylinder 6 | — | W56 | — | 0.5 | MS3PROEVO-B-12 | — | — | — |
| 40 | VANOS intake solenoid | — | W70 | — | 0.5 | MS3PROEVO-C-1 | — | — | — |
| 41 | VANOS exhaust solenoid | — | W71 | — | 0.5 | MS3PROEVO-A-1 | — | — | — |
| 42 | Evap purge valve | — | W72 | — | 0.5 | MS3PROEVO-A-2 | — | — | — |
| 43 | Throttle motor drive 1 (H-bridge) | — | W59 | — | 0.5 | MS3PROEVO-B-30 | — | — | — |
| 44 | Throttle motor drive 2 (H-bridge) | — | W60 | — | 0.5 | MS3PROEVO-B-31 | — | — | — |
| 45 | Map-controlled thermostat | — | W73 | — | 0.5 | MS3PROEVO-A-5 | — | — | — |
| 46 | Idle speed control, close | — | W61 | — | 0.5 | MS3PROEVO-B-32 | — | — | — |
| 47 | Idle speed control, open | — | W62 | — | 0.5 | MS3PROEVO-B-33 | — | — | — |
| 48 | Knock sensor shield | — | W57 | — | 0.5 | SP-SHD-1 | — | — | — |
| 49 | DISA intake flap | — | W74 | — | 0.5 | MS3PROEVO-B-2 | — | — | — |
| 5 | Intake camshaft position | — | W41 | — | 0.5 | MS3PROEVO-B-34 | — | — | — |
| 7 | Throttle body +5V supply | — | W33 | — | 0.5 | SP-5V1-1 | — | — | — |
| 8 | Crankshaft position | — | W37 | — | 0.5 | MS3PROEVO-A-6 | — | — | — |
OEM-X60004
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | Fuel pump relay control | — | W65 | — | 0.5 | MS3PROEVO-C-4 | — | — | — |
| 12 | Pedal ground 2 | — | W24 | — | 0.5 | SP-0V-1 | — | — | — |
| 13 | Pedal position signal 2 | — | W79 | — | 0.5 | MS3PROEVO-A-22 | — | — | — |
| 14 | Pedal +5V supply 2 | — | W34 | — | 0.5 | SP-5V1-1 | — | — | — |
| 7 | Pedal ground 1 | — | W25 | — | 0.5 | SP-0V-1 | — | — | — |
| 8 | Pedal position signal 1 | — | W77 | — | 0.5 | MS3PROEVO-A-20 | — | — | — |
| 9 | Pedal +5V supply 1 | — | W35 | — | 0.5 | SP-5V1-1 | — | — | — |
OEM-X60005
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Ignition coil 3 | — | W47 | — | 0.5 | MS3PROEVO-B-15 | — | — | — |
| 2 | Ignition coil 2 | — | W46 | — | 0.5 | MS3PROEVO-B-14 | — | — | — |
| 3 | Ignition coil 1 | — | W45 | — | 0.5 | MS3PROEVO-B-13 | — | — | — |
| 5 | Ignition ground | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 7 | Ignition coil 6 | — | W50 | — | 0.5 | MS3PROEVO-B-25 | — | — | — |
| 8 | Ignition coil 5 | — | W49 | — | 0.5 | MS3PROEVO-B-24 | — | — | — |
| 9 | Ignition coil 4 | — | W48 | — | 0.5 | MS3PROEVO-B-16 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W12 | — | 0.5 | OEM-X60002-20 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | OEM-X60002-21 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | OEM-X60002-22 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | OEM-X60002-24 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-X60003-15 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | OEM-X60003-17 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | OEM-X60003-18 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | OEM-X60003-20 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | OEM-X60003-21 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | OEM-X60003-23 | — | — | — |
| 1 | — | — | W22 | — | 0.5 | OEM-X60003-25 | — | — | — |
| 1 | — | — | W23 | — | 0.5 | OEM-X60003-28 | — | — | — |
| 1 | — | — | W24 | — | 0.5 | OEM-X60004-12 | — | — | — |
| 1 | — | — | W25 | — | 0.5 | OEM-X60004-7 | — | — | — |
| 1 | — | — | W26 | — | 0.5 | MS3PROEVO-A-13 | — | — | — |
| 1 | — | — | W27 | — | 0.5 | MS3PROEVO-A-18 | — | — | — |
| 1 | — | — | W28 | — | 0.5 | MS3PROEVO-C-17 | — | — | — |
| 1 | — | — | W29 | — | 0.5 | MS3PROEVO-C-18 | — | — | — |
| 1 | — | — | W30 | — | 0.5 | MS3PROEVO-C-19 | — | — | — |
| 1 | — | — | W31 | — | 0.5 | MS3PROEVO-C-20 | — | — | — |
| 1 | — | — | W32 | — | 0.5 | MS3PROEVO-C-21 | — | — | — |
| 1 | — | — | W38 | — | 0.5 | MS3PROEVO-A-15 | — | — | — |
| 1 | — | — | W40 | — | 0.5 | MS3PROEVO-A-27 | — | — | — |
| 1 | — | — | W42 | — | 0.5 | MS3PROEVO-B-35 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-X60001-8 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-X60001-9 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | MS3PROEVO-A-35 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W33 | — | 0.5 | OEM-X60003-7 | — | — | — |
| 1 | — | — | W34 | — | 0.5 | OEM-X60004-14 | — | — | — |
| 1 | — | — | W35 | — | 0.5 | OEM-X60004-9 | — | — | — |
| 1 | — | — | W36 | — | 0.5 | MS3PROEVO-A-8 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W4 | — | 0.85 | OEM-X60001-4 | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-X60001-5 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-X60001-6 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-X60005-5 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | MS3PROEVO-B-3 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | MS3PROEVO-B-5 | — | — | — |
| 1 | — | — | W10 | — | 0.85 | MS3PROEVO-B-7 | — | — | — |
| 1 | — | — | W11 | — | 0.85 | MS3PROEVO-B-9 | — | — | — |
SP-SHD
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W57 | — | 0.5 | OEM-X60003-48 | — | — | — |
| 1 | — | — | W58 | — | 0.5 | MS3PROEVO-A-16 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-X60001-1 | Injector/unloader relay control (terminal 15) | low_side_out | MS3PROEVO-A-28 | Fuel pump relay out | low_side_out | corroborated | |
| OEM-X60001-4 | Power ground | ground | MS3PROEVO-B-3 + MS3PROEVO-B-5 + MS3PROEVO-B-7 + MS3PROEVO-B-9 | Ground + Ground + Ground + Ground | ground | corroborated | |
| OEM-X60001-5 | Power ground | ground | MS3PROEVO-B-3 + MS3PROEVO-B-5 + MS3PROEVO-B-7 + MS3PROEVO-B-9 | Ground + Ground + Ground + Ground | ground | corroborated | |
| OEM-X60001-6 | Power ground | ground | MS3PROEVO-B-3 + MS3PROEVO-B-5 + MS3PROEVO-B-7 + MS3PROEVO-B-9 | Ground + Ground + Ground + Ground | ground | corroborated | |
| OEM-X60001-7 | Battery constant (terminal 30) | power_in | — | — | — | corroborated | |
| OEM-X60001-8 | ECU main power (terminal 87 via main relay) | power_in | MS3PROEVO-A-35 | 12V+ switched power in | power_in | corroborated | |
| OEM-X60001-9 | Voltage supply (injector / fuse carrier) | power_in | MS3PROEVO-A-35 | 12V+ switched power in | power_in | corroborated | |
| OEM-X60002-1 | O2 sensor heater, bank 1 pre-cat | low_side_out | MS3PROEVO-A-29 | PWM out 2 | low_side_out | corroborated | |
| OEM-X60002-13 | O2 sensor heater, bank 2 pre-cat | low_side_out | MS3PROEVO-C-3 | Digital out 2 | low_side_out | corroborated | |
| OEM-X60002-14 | O2 sensor signal, bank 1 pre-cat | lambda_nb_in | MS3PROEVO-A-25 | O2 in | lambda_nb_in | corroborated | |
| OEM-X60002-15 | O2 sensor signal, bank 2 pre-cat | lambda_nb_in | MS3PROEVO-A-23 | Analog In 5 | analog_in | corroborated | |
| OEM-X60002-16 | O2 sensor signal, bank 1 post-cat | lambda_nb_in | MS3PROEVO-A-12 | Analog In 6 | analog_in | corroborated | |
| OEM-X60002-18 | O2 sensor signal, bank 2 post-cat | lambda_nb_in | MS3PROEVO-A-17 | Analog In 7 | analog_in | corroborated | |
| OEM-X60002-19 | O2 sensor heater, bank 2 post-cat | low_side_out | MS3PROEVO-A-30 | PWM out 3 | low_side_out | corroborated | |
| OEM-X60002-20 | O2 sensor ground, bank 1 pre-cat | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60002-21 | O2 sensor ground, bank 2 pre-cat | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60002-22 | O2 sensor ground, bank 1 post-cat | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60002-23 | Main relay control | low_side_out | MS3PROEVO-A-14 | PWM / Idle Out 1 | low_side_out | corroborated | |
| OEM-X60002-24 | O2 sensor ground, bank 2 post-cat | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60002-7 | O2 sensor heater, bank 1 post-cat | low_side_out | MS3PROEVO-C-2 | PWM out 4 | low_side_out | corroborated | |
| OEM-X60003-1 | Mass air flow (MAF) signal | analog_in | MS3PROEVO-A-19 | Analog in 1 | analog_in | corroborated | |
| OEM-X60003-10 | Throttle position sensor 2 | analog_in | MS3PROEVO-A-21 | Analog in 3 | analog_in | corroborated | |
| OEM-X60003-15 | Exhaust camshaft ground | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60003-17 | MAF ground | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60003-18 | Intake camshaft ground | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60003-19 | Throttle position sensor 1 | analog_in | MS3PROEVO-A-9 | TPS in | analog_in | corroborated | |
| OEM-X60003-2 | Exhaust camshaft position | trigger_in | MS3PROEVO-A-26 | CMP+ | trigger_in | corroborated | |
| OEM-X60003-20 | Throttle ground | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60003-21 | Crankshaft ground | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60003-22 | Intake air temperature (IAT) | temp_in | MS3PROEVO-A-11 | CLT in | temp_in | corroborated | |
| OEM-X60003-23 | IAT ground | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60003-24 | Engine coolant temperature (ECT) | temp_in | MS3PROEVO-A-10 | MAT in | temp_in | corroborated | |
| OEM-X60003-25 | ECT ground | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60003-27 | Engine oil temperature | temp_in | MS3PROEVO-C-7 | Analog in 8 | analog_in | corroborated | |
| OEM-X60003-28 | Oil temperature ground | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60003-29 | Knock sensor, cylinders 1-3 (A) | knock_in | MS3PROEVO-A-31 | Knock in 1 | knock_in | corroborated | |
| OEM-X60003-30 | Knock sensor, cylinders 1-3 (B) | knock_in | MS3PROEVO-A-7 | Knock In 2 | knock_in | corroborated | |
| OEM-X60003-31 | Knock sensor, cylinders 4-6 (A) | knock_in | — | — | — | corroborated | |
| OEM-X60003-32 | Knock sensor, cylinders 4-6 (B) | knock_in | — | — | — | corroborated | |
| OEM-X60003-33 | Injector cylinder 1 | injector_out | MS3PROEVO-A-3 | Injector out J | injector_out | corroborated | |
| OEM-X60003-34 | Injector cylinder 2 | injector_out | MS3PROEVO-A-4 | Injector out I | injector_out | corroborated | |
| OEM-X60003-35 | Injector cylinder 3 | injector_out | MS3PROEVO-B-1 | Injector out A | injector_out | corroborated | |
| OEM-X60003-36 | Injector cylinder 4 | injector_out | MS3PROEVO-B-10 | Injector out F | injector_out | corroborated | |
| OEM-X60003-37 | Injector cylinder 5 | injector_out | MS3PROEVO-B-11 | Injector out G | injector_out | corroborated | |
| OEM-X60003-38 | Injector cylinder 6 | injector_out | MS3PROEVO-B-12 | Injector out H | injector_out | corroborated | |
| OEM-X60003-40 | VANOS intake solenoid | low_side_out | MS3PROEVO-C-1 | PWM out 5 | low_side_out | corroborated | |
| OEM-X60003-41 | VANOS exhaust solenoid | low_side_out | MS3PROEVO-A-1 | High current out 1 | low_side_out | corroborated | |
| OEM-X60003-42 | Evap purge valve | low_side_out | MS3PROEVO-A-2 | High current out 2 | low_side_out | corroborated | |
| OEM-X60003-43 | Throttle motor drive 1 (H-bridge) | hbridge_out | MS3PROEVO-B-30 | Stepper IAC out 1B | hbridge_out | corroborated | |
| OEM-X60003-44 | Throttle motor drive 2 (H-bridge) | hbridge_out | MS3PROEVO-B-31 | Stepper IAC out 1A | hbridge_out | corroborated | |
| OEM-X60003-45 | Map-controlled thermostat | low_side_out | MS3PROEVO-A-5 | High current out 3 | low_side_out | corroborated | |
| OEM-X60003-46 | Idle speed control, close | hbridge_out | MS3PROEVO-B-32 | Stepper IAC out 2A | hbridge_out | corroborated | |
| OEM-X60003-47 | Idle speed control, open | hbridge_out | MS3PROEVO-B-33 | Stepper IAC out 2B | hbridge_out | corroborated | |
| OEM-X60003-48 | Knock sensor shield | shield | MS3PROEVO-A-16 | Ground Shield Drain | shield | corroborated | |
| OEM-X60003-49 | DISA intake flap | low_side_out | MS3PROEVO-B-2 | Injector out B | injector_out | corroborated | |
| OEM-X60003-5 | Intake camshaft position | trigger_in | MS3PROEVO-B-34 | Digital Frequency in 1 (VR+) | digital_in | corroborated | |
| OEM-X60003-7 | Throttle body +5V supply | vref | MS3PROEVO-A-8 | 5V+ VREF out | vref | corroborated | |
| OEM-X60003-8 | Crankshaft position | trigger_in | MS3PROEVO-A-6 | CKP+ | trigger_in | corroborated | |
| OEM-X60004-10 | Fuel pump relay control | low_side_out | MS3PROEVO-C-4 | Digital out 1 | low_side_out | corroborated | |
| OEM-X60004-12 | Pedal ground 2 | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60004-13 | Pedal position signal 2 | analog_in | MS3PROEVO-A-22 | Analog In 4 | analog_in | corroborated | |
| OEM-X60004-14 | Pedal +5V supply 2 | vref | MS3PROEVO-A-8 | 5V+ VREF out | vref | corroborated | |
| OEM-X60004-7 | Pedal ground 1 | sensor_ground | MS3PROEVO-A-13 + MS3PROEVO-A-15 + MS3PROEVO-A-18 + MS3PROEVO-A-27 + MS3PROEVO-B-35 + MS3PROEVO-C-17 + MS3PROEVO-C-18 + MS3PROEVO-C-19 + MS3PROEVO-C-20 + MS3PROEVO-C-21 | Logic Ground + CKP− + Sensor return + CMP− + Digital Frequency in 1 (VR−) + Sensor return + Sensor return + Sensor return + Sensor return + Sensor return | digital_in + sensor_ground + trigger_in | corroborated | |
| OEM-X60004-8 | Pedal position signal 1 | analog_in | MS3PROEVO-A-20 | Analog in 2 | analog_in | corroborated | |
| OEM-X60004-9 | Pedal +5V supply 1 | vref | MS3PROEVO-A-8 | 5V+ VREF out | vref | corroborated | |
| OEM-X60005-1 | Ignition coil 3 | ignition_out | MS3PROEVO-B-15 | Spark out C | ignition_out | corroborated | |
| OEM-X60005-2 | Ignition coil 2 | ignition_out | MS3PROEVO-B-14 | Spark out E | ignition_out | corroborated | |
| OEM-X60005-3 | Ignition coil 1 | ignition_out | MS3PROEVO-B-13 | Spark out G | ignition_out | corroborated | |
| OEM-X60005-5 | Ignition ground | ground | MS3PROEVO-B-3 + MS3PROEVO-B-5 + MS3PROEVO-B-7 + MS3PROEVO-B-9 | Ground + Ground + Ground + Ground | ground | corroborated | |
| OEM-X60005-7 | Ignition coil 6 | ignition_out | MS3PROEVO-B-25 | Spark out B | ignition_out | corroborated | |
| OEM-X60005-8 | Ignition coil 5 | ignition_out | MS3PROEVO-B-24 | Spark out F | ignition_out | corroborated | |
| OEM-X60005-9 | Ignition coil 4 | ignition_out | MS3PROEVO-B-16 | Spark out H | ignition_out | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-X60001-8 | SP-14V-1 | 0.85 | no route | ECU main power (terminal 87 via main relay) | — | |
| W2 | OEM-X60001-9 | SP-14V-1 | 0.85 | no route | Voltage supply (injector / fuse carrier) | — | |
| W3 | SP-14V-1 | MS3PROEVO-A-35 | 0.85 | no route | 12V+ switched power in | — | |
| W4 | OEM-X60001-4 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W5 | OEM-X60001-5 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W6 | OEM-X60001-6 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W7 | OEM-X60005-5 | SP-GND-1 | 0.85 | no route | Ignition ground | — | |
| W8 | SP-GND-1 | MS3PROEVO-B-3 | 0.85 | no route | Ground | — | |
| W9 | SP-GND-1 | MS3PROEVO-B-5 | 0.85 | no route | Ground | — | |
| W10 | SP-GND-1 | MS3PROEVO-B-7 | 0.85 | no route | Ground | — | |
| W11 | SP-GND-1 | MS3PROEVO-B-9 | 0.85 | no route | Ground | — | |
| W12 | OEM-X60002-20 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 1 pre-cat | — | |
| W13 | OEM-X60002-21 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 2 pre-cat | — | |
| W14 | OEM-X60002-22 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 1 post-cat | — | |
| W15 | OEM-X60002-24 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 2 post-cat | — | |
| W16 | OEM-X60003-15 | SP-0V-1 | 0.5 | no route | Exhaust camshaft ground | — | |
| W17 | OEM-X60003-17 | SP-0V-1 | 0.5 | no route | MAF ground | — | |
| W18 | OEM-X60003-18 | SP-0V-1 | 0.5 | no route | Intake camshaft ground | — | |
| W19 | OEM-X60003-20 | SP-0V-1 | 0.5 | no route | Throttle ground | — | |
| W20 | OEM-X60003-21 | SP-0V-1 | 0.5 | no route | Crankshaft ground | — | |
| W21 | OEM-X60003-23 | SP-0V-1 | 0.5 | no route | IAT ground | — | |
| W22 | OEM-X60003-25 | SP-0V-1 | 0.5 | no route | ECT ground | — | |
| W23 | OEM-X60003-28 | SP-0V-1 | 0.5 | no route | Oil temperature ground | — | |
| W24 | OEM-X60004-12 | SP-0V-1 | 0.5 | no route | Pedal ground 2 | — | |
| W25 | OEM-X60004-7 | SP-0V-1 | 0.5 | no route | Pedal ground 1 | — | |
| W26 | SP-0V-1 | MS3PROEVO-A-13 | 0.5 | no route | Logic Ground | — | |
| W27 | SP-0V-1 | MS3PROEVO-A-18 | 0.5 | no route | Sensor return | — | |
| W28 | SP-0V-1 | MS3PROEVO-C-17 | 0.5 | no route | Sensor return | — | |
| W29 | SP-0V-1 | MS3PROEVO-C-18 | 0.5 | no route | Sensor return | — | |
| W30 | SP-0V-1 | MS3PROEVO-C-19 | 0.5 | no route | Sensor return | — | |
| W31 | SP-0V-1 | MS3PROEVO-C-20 | 0.5 | no route | Sensor return | — | |
| W32 | SP-0V-1 | MS3PROEVO-C-21 | 0.5 | no route | Sensor return | — | |
| W33 | OEM-X60003-7 | SP-5V1-1 | 0.5 | no route | Throttle body +5V supply | — | |
| W34 | OEM-X60004-14 | SP-5V1-1 | 0.5 | no route | Pedal +5V supply 2 | — | |
| W35 | OEM-X60004-9 | SP-5V1-1 | 0.5 | no route | Pedal +5V supply 1 | — | |
| W36 | SP-5V1-1 | MS3PROEVO-A-8 | 0.5 | no route | 5V+ VREF out | — | |
| W37 | OEM-X60003-8 | MS3PROEVO-A-6 | 0.5 | no route | Crankshaft position | — | |
| W38 | SP-0V-1 | MS3PROEVO-A-15 | 0.5 | no route | CKP− | — | |
| W39 | OEM-X60003-2 | MS3PROEVO-A-26 | 0.5 | no route | Exhaust camshaft position | — | |
| W40 | SP-0V-1 | MS3PROEVO-A-27 | 0.5 | no route | CMP− | — | |
| W41 | OEM-X60003-5 | MS3PROEVO-B-34 | 0.5 | no route | Intake camshaft position | — | |
| W42 | SP-0V-1 | MS3PROEVO-B-35 | 0.5 | no route | Digital Frequency in 1 (VR−) | — | |
| W43 | OEM-X60003-29 | MS3PROEVO-A-31 | 0.5 | no route | Knock sensor, cylinders 1-3 (A) | — | |
| W44 | OEM-X60003-30 | MS3PROEVO-A-7 | 0.5 | no route | Knock sensor, cylinders 1-3 (B) | — | |
| W45 | OEM-X60005-3 | MS3PROEVO-B-13 | 0.5 | no route | Ignition coil 1 | — | |
| W46 | OEM-X60005-2 | MS3PROEVO-B-14 | 0.5 | no route | Ignition coil 2 | — | |
| W47 | OEM-X60005-1 | MS3PROEVO-B-15 | 0.5 | no route | Ignition coil 3 | — | |
| W48 | OEM-X60005-9 | MS3PROEVO-B-16 | 0.5 | no route | Ignition coil 4 | — | |
| W49 | OEM-X60005-8 | MS3PROEVO-B-24 | 0.5 | no route | Ignition coil 5 | — | |
| W50 | OEM-X60005-7 | MS3PROEVO-B-25 | 0.5 | no route | Ignition coil 6 | — | |
| W51 | OEM-X60003-33 | MS3PROEVO-A-3 | 0.5 | no route | Injector cylinder 1 | — | |
| W52 | OEM-X60003-34 | MS3PROEVO-A-4 | 0.5 | no route | Injector cylinder 2 | — | |
| W53 | OEM-X60003-35 | MS3PROEVO-B-1 | 0.5 | no route | Injector cylinder 3 | — | |
| W54 | OEM-X60003-36 | MS3PROEVO-B-10 | 0.5 | no route | Injector cylinder 4 | — | |
| W55 | OEM-X60003-37 | MS3PROEVO-B-11 | 0.5 | no route | Injector cylinder 5 | — | |
| W56 | OEM-X60003-38 | MS3PROEVO-B-12 | 0.5 | no route | Injector cylinder 6 | — | |
| W57 | OEM-X60003-48 | SP-SHD-1 | 0.5 | no route | Knock sensor shield | — | |
| W58 | SP-SHD-1 | MS3PROEVO-A-16 | 0.5 | no route | Ground Shield Drain | — | |
| W59 | OEM-X60003-43 | MS3PROEVO-B-30 | 0.5 | no route | Throttle motor drive 1 (H-bridge) | — | |
| W60 | OEM-X60003-44 | MS3PROEVO-B-31 | 0.5 | no route | Throttle motor drive 2 (H-bridge) | — | |
| W61 | OEM-X60003-46 | MS3PROEVO-B-32 | 0.5 | no route | Idle speed control, close | — | |
| W62 | OEM-X60003-47 | MS3PROEVO-B-33 | 0.5 | no route | Idle speed control, open | — | |
| W63 | OEM-X60001-1 | MS3PROEVO-A-28 | 0.5 | no route | Injector/unloader relay control (terminal 15) | — | |
| W64 | OEM-X60002-23 | MS3PROEVO-A-14 | 0.5 | no route | Main relay control | — | |
| W65 | OEM-X60004-10 | MS3PROEVO-C-4 | 0.5 | no route | Fuel pump relay control | — | |
| W66 | OEM-X60002-1 | MS3PROEVO-A-29 | 0.5 | no route | O2 sensor heater, bank 1 pre-cat | — | |
| W67 | OEM-X60002-13 | MS3PROEVO-C-3 | 0.5 | no route | O2 sensor heater, bank 2 pre-cat | — | |
| W68 | OEM-X60002-19 | MS3PROEVO-A-30 | 0.5 | no route | O2 sensor heater, bank 2 post-cat | — | |
| W69 | OEM-X60002-7 | MS3PROEVO-C-2 | 0.5 | no route | O2 sensor heater, bank 1 post-cat | — | |
| W70 | OEM-X60003-40 | MS3PROEVO-C-1 | 0.5 | no route | VANOS intake solenoid | — | |
| W71 | OEM-X60003-41 | MS3PROEVO-A-1 | 0.5 | no route | VANOS exhaust solenoid | — | |
| W72 | OEM-X60003-42 | MS3PROEVO-A-2 | 0.5 | no route | Evap purge valve | — | |
| W73 | OEM-X60003-45 | MS3PROEVO-A-5 | 0.5 | no route | Map-controlled thermostat | — | |
| W74 | OEM-X60003-49 | MS3PROEVO-B-2 | 0.5 | no route | DISA intake flap | — | |
| W75 | OEM-X60003-1 | MS3PROEVO-A-19 | 0.5 | no route | Mass air flow (MAF) signal | — | |
| W76 | OEM-X60003-19 | MS3PROEVO-A-9 | 0.5 | no route | Throttle position sensor 1 | — | |
| W77 | OEM-X60004-8 | MS3PROEVO-A-20 | 0.5 | no route | Pedal position signal 1 | — | |
| W78 | OEM-X60003-10 | MS3PROEVO-A-21 | 0.5 | no route | Throttle position sensor 2 | — | |
| W79 | OEM-X60004-13 | MS3PROEVO-A-22 | 0.5 | no route | Pedal position signal 2 | — | |
| W80 | OEM-X60002-14 | MS3PROEVO-A-25 | 0.5 | no route | O2 sensor signal, bank 1 pre-cat | — | |
| W81 | OEM-X60002-15 | MS3PROEVO-A-23 | 0.5 | no route | O2 sensor signal, bank 2 pre-cat | — | |
| W82 | OEM-X60002-16 | MS3PROEVO-A-12 | 0.5 | no route | O2 sensor signal, bank 1 post-cat | — | |
| W83 | OEM-X60002-18 | MS3PROEVO-A-17 | 0.5 | no route | O2 sensor signal, bank 2 post-cat | — | |
| W84 | OEM-X60003-24 | MS3PROEVO-A-10 | 0.5 | no route | Engine coolant temperature (ECT) | — | |
| W85 | OEM-X60003-22 | MS3PROEVO-A-11 | 0.5 | no route | Intake air temperature (IAT) | — | |
| W86 | OEM-X60003-27 | MS3PROEVO-C-7 | 0.5 | no route | Engine oil temperature | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | BMW-E46-MS43-CONN | BMW | E46 DME (MS43) harness connector | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (9)
| Severity | Code | Subject | Message |
|---|---|---|---|
| warn | DBW_MOTOR_CURRENT | MS3PROEVO-B-30 | Cannot confirm MS3Pro EVO+ can drive the throttle motor: MS3PROEVO-B-30 "Stepper IAC out 1B" is rated 0.75 A, but the motor current at OEM-X60003-43 is unknown. Add the motor's peak current from a source, or measure the motor resistance: peak ≈ 14 V ÷ R (Hondata measured 4.9 A for a Civic Si body, 10.4 A for a ZDX body; holding current is about 1 A). |
| warn | DBW_MOTOR_CURRENT | MS3PROEVO-B-31 | Cannot confirm MS3Pro EVO+ can drive the throttle motor: MS3PROEVO-B-31 "Stepper IAC out 1A" is rated 0.75 A, but the motor current at OEM-X60003-44 is unknown. Add the motor's peak current from a source, or measure the motor resistance: peak ≈ 14 V ÷ R (Hondata measured 4.9 A for a Civic Si body, 10.4 A for a ZDX body; holding current is about 1 A). |
| warn | NET_FAMILY | MS3PROEVO-A-15 ↔ MS3PROEVO-B-35 | MS3PROEVO-A-15 "CKP−" [trigger_in] is wired to MS3PROEVO-B-35 "Digital Frequency in 1 (VR−)" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| warn | NET_FAMILY | OEM-X60003-5 ↔ MS3PROEVO-B-34 | OEM-X60003-5 "Intake camshaft position" [trigger_in] is wired to MS3PROEVO-B-34 "Digital Frequency in 1 (VR+)" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| info | NET_FAMILY | MS3PROEVO-A-13 ↔ MS3PROEVO-B-35 | MS3PROEVO-A-13 "Logic Ground" [sensor_ground] is wired to MS3PROEVO-B-35 "Digital Frequency in 1 (VR−)" [digital_in]. A digital input used as a ground/identification strap (e.g. AT/MT ID is grounded on manual cars) is compatible with a sensor ground. |
| info | NET_FAMILY | OEM-X60003-21 ↔ MS3PROEVO-A-27 | OEM-X60003-21 "Crankshaft ground" [sensor_ground] is wired to MS3PROEVO-A-27 "CMP−" [trigger_in]. Trigger return tied to sensor/trigger ground: correct for single-ended trigger inputs. |
| info | NET_FAMILY | OEM-X60003-27 ↔ MS3PROEVO-C-7 | OEM-X60003-27 "Engine oil temperature" [temp_in] is wired to MS3PROEVO-C-7 "Analog in 8" [analog_in]. Thermistor on a plain analog input needs a pull-up; check the channel can enable one. |
| info | NET_FAMILY | OEM-X60003-49 ↔ MS3PROEVO-B-2 | OEM-X60003-49 "DISA intake flap" [low_side_out] is wired to MS3PROEVO-B-2 "Injector out B" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | UNMAPPED | OEM | 2 optional OEM pins are not mapped: OEM-X60003-31 Knock sensor, cylinders 4-6 (A); OEM-X60003-32 Knock sensor, cylinders 4-6 (B) |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-X60001-7 | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
Notes
Fit check: unconfirmed. Confirm these before building: - Needs CAN (E46 K-bus/CAN); not documented for this ECU - This car has EWS 3.3 (rolling code) immobilizer; needs a delete/bypass Auto-mapped by auto_map() from the library pin data on 2026-10-06. Review every wire against both manuals before building. Not wired: - OEM-X60001 7: Battery constant (terminal 30): AMP EFI MS3Pro EVO+ has no battery-constant input; not needed - OEM-X60003 31: Knock sensor, cylinders 4-6 (A): no free knock input on AMP EFI MS3Pro EVO+ - OEM-X60003 32: Knock sensor, cylinders 4-6 (B): no free knock input on AMP EFI MS3Pro EVO+ - MS3PROEVO-B 19: Digital switched 12V in: not fed (the stock ECU has no ignition-sense pin); feed it from a switched-ignition source
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | AMP EFI: MS3Pro EVO+ / EVO+ HC manual (fw 1.6.1) pinout tables | https://cdn.shopify.com/s/files/1/0960/0014/7754/files/MS3Pro_User_Manual_Firmware_1.6.1_EVO.pdf?v=1760643022 | archive | 2026-10-05 | d5dd8a31822d |
| 2 | community_copy | ms4x.net: Siemens MS43 Pinout | https://www.ms4x.net/index.php?title=Siemens_MS43_Pinout | — | — | — |
| 2 | community_copy | rusefi wiki: 2002 BMW 325 / 2004 BMW 330Ci E46 DME pinout (M54/MS43) | https://github.com/rusefi/rusefi/wiki/2002-BMW-325-and-2004-BMW-330Ci-E46-DME-pinout | — | — | — |