BMW 3 Series E46 1998–2006 (M54) → MaxxECU MaxxECU RACE REV9+ (auto)
BMW 3 Series E46 1998–2006 (M54) — MaxxECU — MaxxECU RACE
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-08
Before you start
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 1: read the Findings page before cutting any wire |
| Size of the job | 72 wires · 12 connectors · 1 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-X60001-8 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-X60001-9 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | MAXXECURACE-C1-M4 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-X60001-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-X60001-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-X60001-6 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-X60005-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | SP-GND-1 | MAXXECURACE-C1-L4 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | MAXXECURACE-C2-G4 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-X60002-20 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-X60002-21 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-X60002-22 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-X60002-24 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-X60003-15 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-X60003-17 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-X60003-18 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-X60003-20 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-X60003-21 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-X60003-23 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-X60003-25 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-X60003-28 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-X60004-12 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-X60004-7 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | SP-0V-1 | MAXXECURACE-C1-H1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | SP-0V-1 | MAXXECURACE-C1-H2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-X60003-7 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-X60004-14 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-X60004-9 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | SP-5V1-1 | MAXXECURACE-C1-G1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-X60003-8 | MAXXECURACE-C1-H3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-X60003-2 | MAXXECURACE-C1-H4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-X60003-29 | MAXXECURACE-C2-E2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-X60003-30 | MAXXECURACE-C2-E3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-X60005-3 | MAXXECURACE-C1-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-X60005-2 | MAXXECURACE-C1-A3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-X60005-1 | MAXXECURACE-C1-B2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-X60005-9 | MAXXECURACE-C1-B3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-X60005-8 | MAXXECURACE-C1-C2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-X60005-7 | MAXXECURACE-C1-C3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-X60003-33 | MAXXECURACE-C1-K1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-X60003-34 | MAXXECURACE-C1-K2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-X60003-35 | MAXXECURACE-C1-M1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-X60003-36 | MAXXECURACE-C1-M2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-X60003-37 | MAXXECURACE-C1-M3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-X60003-38 | MAXXECURACE-C1-L3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-X60003-48 | SP-SHD-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | SP-SHD-1 | MAXXECURACE-C1-E3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | OEM-X60003-43 | MAXXECURACE-C2-H2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W49 | OEM-X60003-44 | MAXXECURACE-C2-H4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W50 | OEM-X60003-46 | MAXXECURACE-C2-H1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W51 | OEM-X60003-47 | MAXXECURACE-C2-H3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W52 | OEM-X60001-1 | MAXXECURACE-C1-B4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W53 | OEM-X60002-23 | MAXXECURACE-C1-C4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W54 | OEM-X60004-10 | MAXXECURACE-C1-D4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W55 | OEM-X60002-1 | MAXXECURACE-C1-D1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W56 | OEM-X60002-13 | MAXXECURACE-C1-E4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W57 | OEM-X60002-19 | MAXXECURACE-C1-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W58 | OEM-X60002-7 | MAXXECURACE-C1-B1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W59 | OEM-X60003-40 | MAXXECURACE-C1-C1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W60 | OEM-X60003-41 | MAXXECURACE-C1-A4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W61 | OEM-X60003-42 | MAXXECURACE-C1-L2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W62 | OEM-X60003-45 | MAXXECURACE-C1-L1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W63 | OEM-X60003-1 | MAXXECURACE-C1-J3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W64 | OEM-X60003-19 | MAXXECURACE-C1-G2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W65 | OEM-X60004-8 | MAXXECURACE-C1-J4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W66 | OEM-X60003-10 | MAXXECURACE-C2-G3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W67 | OEM-X60004-13 | MAXXECURACE-C2-E4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W68 | OEM-X60002-14 | MAXXECURACE-C2-F1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W69 | OEM-X60002-15 | MAXXECURACE-C2-F2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W70 | OEM-X60003-24 | MAXXECURACE-C1-J1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W71 | OEM-X60003-22 | MAXXECURACE-C1-J2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W72 | OEM-X60003-27 | MAXXECURACE-C1-F1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | MAXXECURACE-C1-M4 | MAXXECURACE-C1-H1 | open (OL) | +12 V supply must not touch sensor ground | |
| 2 | MAXXECURACE-C1-H1 | MAXXECURACE-C1-G1 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 3 | MAXXECURACE-C1-L4 | MAXXECURACE-C1-G1 | open (OL) | power ground must not touch 5 V sensor reference | |
| 4 | MAXXECURACE-C1-L4 | MAXXECURACE-C1-M4 | open (OL) | power ground must not touch +12 V supply | |
| 5 | MAXXECURACE-C1-M4 | MAXXECURACE-C1-G1 | open (OL) | +12 V supply must not touch 5 V sensor reference |
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
MAXXECURACE-C1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A1 | GPO 5 | — | W57 | — | 0.5 | OEM-X60002-19 | — | — | — |
| A2 | IGN 1 | — | W34 | — | 0.5 | OEM-X60005-3 | — | — | — |
| A3 | IGN 2 | — | W35 | — | 0.5 | OEM-X60005-2 | — | — | — |
| A4 | GPO 8/TACHO | — | W60 | — | 0.5 | OEM-X60003-41 | — | — | — |
| B1 | GPO 6 | — | W58 | — | 0.5 | OEM-X60002-7 | — | — | — |
| B2 | IGN 3 | — | W36 | — | 0.5 | OEM-X60005-1 | — | — | — |
| B3 | IGN 4 | — | W37 | — | 0.5 | OEM-X60005-9 | — | — | — |
| B4 | GPO 1 | — | W52 | — | 0.5 | OEM-X60001-1 | — | — | — |
| C1 | GPO 7 | — | W59 | — | 0.5 | OEM-X60003-40 | — | — | — |
| C2 | IGN 5 | — | W38 | — | 0.5 | OEM-X60005-8 | — | — | — |
| C3 | IGN 6 | — | W39 | — | 0.5 | OEM-X60005-7 | — | — | — |
| C4 | GPO 2 | — | W53 | — | 0.5 | OEM-X60002-23 | — | — | — |
| D1 | WBO2 Heater- | — | W55 | — | 0.5 | OEM-X60002-1 | — | — | — |
| D2 | IGN 7 | — | — | — | — | — | — | — | — |
| D3 | IGN 8 | — | — | — | — | — | — | — | — |
| D4 | GPO 3 | — | W54 | — | 0.5 | OEM-X60004-10 | — | — | — |
| E1 | CAN H | — | — | — | — | — | — | — | — |
| E2 | CAN L | — | — | — | — | — | — | — | — |
| E3 | GND Shield | — | W47 | — | 0.5 | SP-SHD-1 | — | — | — |
| E4 | GPO 4 | — | W56 | — | 0.5 | OEM-X60002-13 | — | — | — |
| F1 | CLT | — | W72 | — | 0.5 | OEM-X60003-27 | — | — | — |
| F2 | IAT | — | — | — | — | — | — | — | — |
| F3 | WBO2 VREF | — | — | — | — | — | — | — | — |
| F4 | WBO2 VS | — | — | — | — | — | — | — | — |
| G1 | +5V sensor supply | — | W29 | — | 0.5 | SP-5V1-1 | — | — | — |
| G2 | TPS/AIN | — | W64 | — | 0.5 | OEM-X60003-19 | — | — | — |
| G3 | WBO2 IP | — | — | — | — | — | — | — | — |
| G4 | WBO2 RCAL | — | — | — | — | — | — | — | — |
| H1 | Sensor GND | — | W24 | — | 0.5 | SP-0V-1 | — | — | — |
| H2 | Trigger GND | — | W25 | — | 0.5 | SP-0V-1 | — | — | — |
| H3 | TRIGGER | — | W30 | — | 0.5 | OEM-X60003-8 | — | — | — |
| H4 | HOME | — | W31 | — | 0.5 | OEM-X60003-2 | — | — | — |
| J1 | AIN 1 (temperature) | — | W70 | — | 0.5 | OEM-X60003-24 | — | — | — |
| J2 | AIN 2 (temperature) | — | W71 | — | 0.5 | OEM-X60003-22 | — | — | — |
| J3 | AIN 3 (0-5V) | — | W63 | — | 0.5 | OEM-X60003-1 | — | — | — |
| J4 | AIN 4 (0-5V) | — | W65 | — | 0.5 | OEM-X60004-8 | — | — | — |
| K1 | INJ 1 | — | W40 | — | 0.5 | OEM-X60003-33 | — | — | — |
| K2 | INJ 2 | — | W41 | — | 0.5 | OEM-X60003-34 | — | — | — |
| K3 | DIN/VR 1 | — | — | — | — | — | — | — | — |
| K4 | DIN/VR 2 | — | — | — | — | — | — | — | — |
| L1 | INJ 8 | — | W62 | — | 0.5 | OEM-X60003-45 | — | — | — |
| L2 | INJ 7 | — | W61 | — | 0.5 | OEM-X60003-42 | — | — | — |
| L3 | INJ 6 | — | W45 | — | 0.5 | OEM-X60003-38 | — | — | — |
| L4 | Engine GND | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| M1 | INJ 3 | — | W42 | — | 0.5 | OEM-X60003-35 | — | — | — |
| M2 | INJ 4 | — | W43 | — | 0.5 | OEM-X60003-36 | — | — | — |
| M3 | INJ 5 | — | W44 | — | 0.5 | OEM-X60003-37 | — | — | — |
| M4 | +12V ECU power supply | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
MAXXECURACE-C2
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A1 | EGT 5+ | — | — | — | — | — | — | — | — |
| A2 | EGT 6+ | — | — | — | — | — | — | — | — |
| A3 | EGT 7+ | — | — | — | — | — | — | — | — |
| A4 | EGT 8+ | — | — | — | — | — | — | — | — |
| B1 | EGT 5- | — | — | — | — | — | — | — | — |
| B2 | EGT 6- | — | — | — | — | — | — | — | — |
| B3 | EGT 7- | — | — | — | — | — | — | — | — |
| B4 | EGT 8- | — | — | — | — | — | — | — | — |
| C1 | EGT 1+ | — | — | — | — | — | — | — | — |
| C2 | EGT 2+ | — | — | — | — | — | — | — | — |
| C3 | EGT 3+ | — | — | — | — | — | — | — | — |
| C4 | EGT 4+ | — | — | — | — | — | — | — | — |
| D1 | EGT 1- | — | — | — | — | — | — | — | — |
| D2 | EGT 2- | — | — | — | — | — | — | — | — |
| D3 | EGT 3- | — | — | — | — | — | — | — | — |
| D4 | EGT 4- | — | — | — | — | — | — | — | — |
| E1 | KNOCK GND | — | — | — | — | — | — | — | — |
| E2 | Knock 1 | — | W32 | — | 0.5 | OEM-X60003-29 | — | — | — |
| E3 | Knock 2 | — | W33 | — | 0.5 | OEM-X60003-30 | — | — | — |
| E4 | AIN 6 (0-5V) | — | W67 | — | 0.5 | OEM-X60004-13 | — | — | — |
| F1 | AIN 7 (0-5V) | — | W68 | — | 0.5 | OEM-X60002-14 | — | — | — |
| F2 | AIN 8 (0-5V) | — | W69 | — | 0.5 | OEM-X60002-15 | — | — | — |
| F3 | DIN/VR 4 | — | — | — | — | — | — | — | — |
| F4 | DIN/VR 5 | — | — | — | — | — | — | — | — |
| G1 | GPO 15 (+12V) | — | — | — | — | — | — | — | — |
| G2 | GPO 16 (+12V) | — | — | — | — | — | — | — | — |
| G3 | AIN 5 (0-5V) | — | W66 | — | 0.5 | OEM-X60003-10 | — | — | — |
| G4 | ENGINE GROUND | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| H1 | MOTOR 2+ | — | W50 | — | 0.5 | OEM-X60003-46 | — | — | — |
| H2 | MOTOR 1- | — | W48 | — | 0.5 | OEM-X60003-43 | — | — | — |
| H3 | MOTOR 2- | — | W51 | — | 0.5 | OEM-X60003-47 | — | — | — |
| H4 | MOTOR 1+ | — | W49 | — | 0.5 | OEM-X60003-44 | — | — | — |
OEM-X60001
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector/unloader relay control (terminal 15) | — | W52 | — | 0.5 | MAXXECURACE-C1-B4 | — | — | — |
| 4 | Power ground | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | Power ground | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Power ground | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 7 | Battery constant (terminal 30) | — | — | — | — | — | — | — | — |
| 8 | ECU main power (terminal 87 via main relay) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 9 | Voltage supply (injector / fuse carrier) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
OEM-X60002
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | O2 sensor heater, bank 1 pre-cat | — | W55 | — | 0.5 | MAXXECURACE-C1-D1 | — | — | — |
| 13 | O2 sensor heater, bank 2 pre-cat | — | W56 | — | 0.5 | MAXXECURACE-C1-E4 | — | — | — |
| 14 | O2 sensor signal, bank 1 pre-cat | — | W68 | — | 0.5 | MAXXECURACE-C2-F1 | — | — | — |
| 15 | O2 sensor signal, bank 2 pre-cat | — | W69 | — | 0.5 | MAXXECURACE-C2-F2 | — | — | — |
| 16 | O2 sensor signal, bank 1 post-cat | — | — | — | — | — | — | — | — |
| 18 | O2 sensor signal, bank 2 post-cat | — | — | — | — | — | — | — | — |
| 19 | O2 sensor heater, bank 2 post-cat | — | W57 | — | 0.5 | MAXXECURACE-C1-A1 | — | — | — |
| 20 | O2 sensor ground, bank 1 pre-cat | — | W10 | — | 0.5 | SP-0V-1 | — | — | — |
| 21 | O2 sensor ground, bank 2 pre-cat | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | O2 sensor ground, bank 1 post-cat | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| 23 | Main relay control | — | W53 | — | 0.5 | MAXXECURACE-C1-C4 | — | — | — |
| 24 | O2 sensor ground, bank 2 post-cat | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 7 | O2 sensor heater, bank 1 post-cat | — | W58 | — | 0.5 | MAXXECURACE-C1-B1 | — | — | — |
OEM-X60003
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Mass air flow (MAF) signal | — | W63 | — | 0.5 | MAXXECURACE-C1-J3 | — | — | — |
| 10 | Throttle position sensor 2 | — | W66 | — | 0.5 | MAXXECURACE-C2-G3 | — | — | — |
| 15 | Exhaust camshaft ground | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 17 | MAF ground | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 18 | Intake camshaft ground | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 19 | Throttle position sensor 1 | — | W64 | — | 0.5 | MAXXECURACE-C1-G2 | — | — | — |
| 2 | Exhaust camshaft position | — | W31 | — | 0.5 | MAXXECURACE-C1-H4 | — | — | — |
| 20 | Throttle ground | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 21 | Crankshaft ground | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | Intake air temperature (IAT) | — | W71 | — | 0.5 | MAXXECURACE-C1-J2 | — | — | — |
| 23 | IAT ground | — | W19 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | Engine coolant temperature (ECT) | — | W70 | — | 0.5 | MAXXECURACE-C1-J1 | — | — | — |
| 25 | ECT ground | — | W20 | — | 0.5 | SP-0V-1 | — | — | — |
| 27 | Engine oil temperature | — | W72 | — | 0.5 | MAXXECURACE-C1-F1 | — | — | — |
| 28 | Oil temperature ground | — | W21 | — | 0.5 | SP-0V-1 | — | — | — |
| 29 | Knock sensor, cylinders 1-3 (A) | — | W32 | — | 0.5 | MAXXECURACE-C2-E2 | — | — | — |
| 30 | Knock sensor, cylinders 1-3 (B) | — | W33 | — | 0.5 | MAXXECURACE-C2-E3 | — | — | — |
| 31 | Knock sensor, cylinders 4-6 (A) | — | — | — | — | — | — | — | — |
| 32 | Knock sensor, cylinders 4-6 (B) | — | — | — | — | — | — | — | — |
| 33 | Injector cylinder 1 | — | W40 | — | 0.5 | MAXXECURACE-C1-K1 | — | — | — |
| 34 | Injector cylinder 2 | — | W41 | — | 0.5 | MAXXECURACE-C1-K2 | — | — | — |
| 35 | Injector cylinder 3 | — | W42 | — | 0.5 | MAXXECURACE-C1-M1 | — | — | — |
| 36 | Injector cylinder 4 | — | W43 | — | 0.5 | MAXXECURACE-C1-M2 | — | — | — |
| 37 | Injector cylinder 5 | — | W44 | — | 0.5 | MAXXECURACE-C1-M3 | — | — | — |
| 38 | Injector cylinder 6 | — | W45 | — | 0.5 | MAXXECURACE-C1-L3 | — | — | — |
| 40 | VANOS intake solenoid | — | W59 | — | 0.5 | MAXXECURACE-C1-C1 | — | — | — |
| 41 | VANOS exhaust solenoid | — | W60 | — | 0.5 | MAXXECURACE-C1-A4 | — | — | — |
| 42 | Evap purge valve | — | W61 | — | 0.5 | MAXXECURACE-C1-L2 | — | — | — |
| 43 | Throttle motor drive 1 (H-bridge) | — | W48 | — | 0.5 | MAXXECURACE-C2-H2 | — | — | — |
| 44 | Throttle motor drive 2 (H-bridge) | — | W49 | — | 0.5 | MAXXECURACE-C2-H4 | — | — | — |
| 45 | Map-controlled thermostat | — | W62 | — | 0.5 | MAXXECURACE-C1-L1 | — | — | — |
| 46 | Idle speed control, close | — | W50 | — | 0.5 | MAXXECURACE-C2-H1 | — | — | — |
| 47 | Idle speed control, open | — | W51 | — | 0.5 | MAXXECURACE-C2-H3 | — | — | — |
| 48 | Knock sensor shield | — | W46 | — | 0.5 | SP-SHD-1 | — | — | — |
| 49 | DISA intake flap | — | — | — | — | — | — | — | — |
| 5 | Intake camshaft position | — | — | — | — | — | — | — | — |
| 7 | Throttle body +5V supply | — | W26 | — | 0.5 | SP-5V1-1 | — | — | — |
| 8 | Crankshaft position | — | W30 | — | 0.5 | MAXXECURACE-C1-H3 | — | — | — |
OEM-X60004
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | Fuel pump relay control | — | W54 | — | 0.5 | MAXXECURACE-C1-D4 | — | — | — |
| 12 | Pedal ground 2 | — | W22 | — | 0.5 | SP-0V-1 | — | — | — |
| 13 | Pedal position signal 2 | — | W67 | — | 0.5 | MAXXECURACE-C2-E4 | — | — | — |
| 14 | Pedal +5V supply 2 | — | W27 | — | 0.5 | SP-5V1-1 | — | — | — |
| 7 | Pedal ground 1 | — | W23 | — | 0.5 | SP-0V-1 | — | — | — |
| 8 | Pedal position signal 1 | — | W65 | — | 0.5 | MAXXECURACE-C1-J4 | — | — | — |
| 9 | Pedal +5V supply 1 | — | W28 | — | 0.5 | SP-5V1-1 | — | — | — |
OEM-X60005
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Ignition coil 3 | — | W36 | — | 0.5 | MAXXECURACE-C1-B2 | — | — | — |
| 2 | Ignition coil 2 | — | W35 | — | 0.5 | MAXXECURACE-C1-A3 | — | — | — |
| 3 | Ignition coil 1 | — | W34 | — | 0.5 | MAXXECURACE-C1-A2 | — | — | — |
| 5 | Ignition ground | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 7 | Ignition coil 6 | — | W39 | — | 0.5 | MAXXECURACE-C1-C3 | — | — | — |
| 8 | Ignition coil 5 | — | W38 | — | 0.5 | MAXXECURACE-C1-C2 | — | — | — |
| 9 | Ignition coil 4 | — | W37 | — | 0.5 | MAXXECURACE-C1-B3 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W10 | — | 0.5 | OEM-X60002-20 | — | — | — |
| 1 | — | — | W11 | — | 0.5 | OEM-X60002-21 | — | — | — |
| 1 | — | — | W12 | — | 0.5 | OEM-X60002-22 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | OEM-X60002-24 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | OEM-X60003-15 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | OEM-X60003-17 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-X60003-18 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | OEM-X60003-20 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | OEM-X60003-21 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | OEM-X60003-23 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | OEM-X60003-25 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | OEM-X60003-28 | — | — | — |
| 1 | — | — | W22 | — | 0.5 | OEM-X60004-12 | — | — | — |
| 1 | — | — | W23 | — | 0.5 | OEM-X60004-7 | — | — | — |
| 1 | — | — | W24 | — | 0.5 | MAXXECURACE-C1-H1 | — | — | — |
| 1 | — | — | W25 | — | 0.5 | MAXXECURACE-C1-H2 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-X60001-8 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-X60001-9 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | MAXXECURACE-C1-M4 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W26 | — | 0.5 | OEM-X60003-7 | — | — | — |
| 1 | — | — | W27 | — | 0.5 | OEM-X60004-14 | — | — | — |
| 1 | — | — | W28 | — | 0.5 | OEM-X60004-9 | — | — | — |
| 1 | — | — | W29 | — | 0.5 | MAXXECURACE-C1-G1 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W4 | — | 0.85 | OEM-X60001-4 | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-X60001-5 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-X60001-6 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-X60005-5 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | MAXXECURACE-C1-L4 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | MAXXECURACE-C2-G4 | — | — | — |
SP-SHD
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W46 | — | 0.5 | OEM-X60003-48 | — | — | — |
| 1 | — | — | W47 | — | 0.5 | MAXXECURACE-C1-E3 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-X60001-1 | Injector/unloader relay control (terminal 15) | low_side_out | MAXXECURACE-C1-B4 | GPO 1 | low_side_out | corroborated | |
| OEM-X60001-4 | Power ground | ground | MAXXECURACE-C1-L4 + MAXXECURACE-C2-G4 | Engine GND + ENGINE GROUND | ground | corroborated | |
| OEM-X60001-5 | Power ground | ground | MAXXECURACE-C1-L4 + MAXXECURACE-C2-G4 | Engine GND + ENGINE GROUND | ground | corroborated | |
| OEM-X60001-6 | Power ground | ground | MAXXECURACE-C1-L4 + MAXXECURACE-C2-G4 | Engine GND + ENGINE GROUND | ground | corroborated | |
| OEM-X60001-7 | Battery constant (terminal 30) | power_in | — | — | — | corroborated | |
| OEM-X60001-8 | ECU main power (terminal 87 via main relay) | power_in | MAXXECURACE-C1-M4 | +12V ECU power supply | power_in | corroborated | |
| OEM-X60001-9 | Voltage supply (injector / fuse carrier) | power_in | MAXXECURACE-C1-M4 | +12V ECU power supply | power_in | corroborated | |
| OEM-X60002-1 | O2 sensor heater, bank 1 pre-cat | low_side_out | MAXXECURACE-C1-D1 | WBO2 Heater- | low_side_out | corroborated | |
| OEM-X60002-13 | O2 sensor heater, bank 2 pre-cat | low_side_out | MAXXECURACE-C1-E4 | GPO 4 | low_side_out | corroborated | |
| OEM-X60002-14 | O2 sensor signal, bank 1 pre-cat | lambda_nb_in | MAXXECURACE-C2-F1 | AIN 7 (0-5V) | analog_in | corroborated | |
| OEM-X60002-15 | O2 sensor signal, bank 2 pre-cat | lambda_nb_in | MAXXECURACE-C2-F2 | AIN 8 (0-5V) | analog_in | corroborated | |
| OEM-X60002-16 | O2 sensor signal, bank 1 post-cat | lambda_nb_in | — | — | — | corroborated | |
| OEM-X60002-18 | O2 sensor signal, bank 2 post-cat | lambda_nb_in | — | — | — | corroborated | |
| OEM-X60002-19 | O2 sensor heater, bank 2 post-cat | low_side_out | MAXXECURACE-C1-A1 | GPO 5 | low_side_out | corroborated | |
| OEM-X60002-20 | O2 sensor ground, bank 1 pre-cat | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60002-21 | O2 sensor ground, bank 2 pre-cat | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60002-22 | O2 sensor ground, bank 1 post-cat | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60002-23 | Main relay control | low_side_out | MAXXECURACE-C1-C4 | GPO 2 | low_side_out | corroborated | |
| OEM-X60002-24 | O2 sensor ground, bank 2 post-cat | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60002-7 | O2 sensor heater, bank 1 post-cat | low_side_out | MAXXECURACE-C1-B1 | GPO 6 | low_side_out | corroborated | |
| OEM-X60003-1 | Mass air flow (MAF) signal | analog_in | MAXXECURACE-C1-J3 | AIN 3 (0-5V) | analog_in | corroborated | |
| OEM-X60003-10 | Throttle position sensor 2 | analog_in | MAXXECURACE-C2-G3 | AIN 5 (0-5V) | analog_in | corroborated | |
| OEM-X60003-15 | Exhaust camshaft ground | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60003-17 | MAF ground | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60003-18 | Intake camshaft ground | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60003-19 | Throttle position sensor 1 | analog_in | MAXXECURACE-C1-G2 | TPS/AIN | analog_in | corroborated | |
| OEM-X60003-2 | Exhaust camshaft position | trigger_in | MAXXECURACE-C1-H4 | HOME | trigger_in | corroborated | |
| OEM-X60003-20 | Throttle ground | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60003-21 | Crankshaft ground | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60003-22 | Intake air temperature (IAT) | temp_in | MAXXECURACE-C1-J2 | AIN 2 (temperature) | temp_in | corroborated | |
| OEM-X60003-23 | IAT ground | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60003-24 | Engine coolant temperature (ECT) | temp_in | MAXXECURACE-C1-J1 | AIN 1 (temperature) | temp_in | corroborated | |
| OEM-X60003-25 | ECT ground | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60003-27 | Engine oil temperature | temp_in | MAXXECURACE-C1-F1 | CLT | temp_in | corroborated | |
| OEM-X60003-28 | Oil temperature ground | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60003-29 | Knock sensor, cylinders 1-3 (A) | knock_in | MAXXECURACE-C2-E2 | Knock 1 | knock_in | corroborated | |
| OEM-X60003-30 | Knock sensor, cylinders 1-3 (B) | knock_in | MAXXECURACE-C2-E3 | Knock 2 | knock_in | corroborated | |
| OEM-X60003-31 | Knock sensor, cylinders 4-6 (A) | knock_in | — | — | — | corroborated | |
| OEM-X60003-32 | Knock sensor, cylinders 4-6 (B) | knock_in | — | — | — | corroborated | |
| OEM-X60003-33 | Injector cylinder 1 | injector_out | MAXXECURACE-C1-K1 | INJ 1 | injector_out | corroborated | |
| OEM-X60003-34 | Injector cylinder 2 | injector_out | MAXXECURACE-C1-K2 | INJ 2 | injector_out | corroborated | |
| OEM-X60003-35 | Injector cylinder 3 | injector_out | MAXXECURACE-C1-M1 | INJ 3 | injector_out | corroborated | |
| OEM-X60003-36 | Injector cylinder 4 | injector_out | MAXXECURACE-C1-M2 | INJ 4 | injector_out | corroborated | |
| OEM-X60003-37 | Injector cylinder 5 | injector_out | MAXXECURACE-C1-M3 | INJ 5 | injector_out | corroborated | |
| OEM-X60003-38 | Injector cylinder 6 | injector_out | MAXXECURACE-C1-L3 | INJ 6 | injector_out | corroborated | |
| OEM-X60003-40 | VANOS intake solenoid | low_side_out | MAXXECURACE-C1-C1 | GPO 7 | low_side_out | corroborated | |
| OEM-X60003-41 | VANOS exhaust solenoid | low_side_out | MAXXECURACE-C1-A4 | GPO 8/TACHO | low_side_out | corroborated | |
| OEM-X60003-42 | Evap purge valve | low_side_out | MAXXECURACE-C1-L2 | INJ 7 | injector_out | corroborated | |
| OEM-X60003-43 | Throttle motor drive 1 (H-bridge) | hbridge_out | MAXXECURACE-C2-H2 | MOTOR 1- | hbridge_out | corroborated | |
| OEM-X60003-44 | Throttle motor drive 2 (H-bridge) | hbridge_out | MAXXECURACE-C2-H4 | MOTOR 1+ | hbridge_out | corroborated | |
| OEM-X60003-45 | Map-controlled thermostat | low_side_out | MAXXECURACE-C1-L1 | INJ 8 | injector_out | corroborated | |
| OEM-X60003-46 | Idle speed control, close | hbridge_out | MAXXECURACE-C2-H1 | MOTOR 2+ | hbridge_out | corroborated | |
| OEM-X60003-47 | Idle speed control, open | hbridge_out | MAXXECURACE-C2-H3 | MOTOR 2- | hbridge_out | corroborated | |
| OEM-X60003-48 | Knock sensor shield | shield | MAXXECURACE-C1-E3 | GND Shield | shield | corroborated | |
| OEM-X60003-49 | DISA intake flap | low_side_out | — | — | — | corroborated | |
| OEM-X60003-5 | Intake camshaft position | trigger_in | — | — | — | corroborated | |
| OEM-X60003-7 | Throttle body +5V supply | vref | MAXXECURACE-C1-G1 | +5V sensor supply | vref | corroborated | |
| OEM-X60003-8 | Crankshaft position | trigger_in | MAXXECURACE-C1-H3 | TRIGGER | trigger_in | corroborated | |
| OEM-X60004-10 | Fuel pump relay control | low_side_out | MAXXECURACE-C1-D4 | GPO 3 | low_side_out | corroborated | |
| OEM-X60004-12 | Pedal ground 2 | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60004-13 | Pedal position signal 2 | analog_in | MAXXECURACE-C2-E4 | AIN 6 (0-5V) | analog_in | corroborated | |
| OEM-X60004-14 | Pedal +5V supply 2 | vref | MAXXECURACE-C1-G1 | +5V sensor supply | vref | corroborated | |
| OEM-X60004-7 | Pedal ground 1 | sensor_ground | MAXXECURACE-C1-H1 + MAXXECURACE-C1-H2 | Sensor GND + Trigger GND | sensor_ground | corroborated | |
| OEM-X60004-8 | Pedal position signal 1 | analog_in | MAXXECURACE-C1-J4 | AIN 4 (0-5V) | analog_in | corroborated | |
| OEM-X60004-9 | Pedal +5V supply 1 | vref | MAXXECURACE-C1-G1 | +5V sensor supply | vref | corroborated | |
| OEM-X60005-1 | Ignition coil 3 | ignition_out | MAXXECURACE-C1-B2 | IGN 3 | ignition_out | corroborated | |
| OEM-X60005-2 | Ignition coil 2 | ignition_out | MAXXECURACE-C1-A3 | IGN 2 | ignition_out | corroborated | |
| OEM-X60005-3 | Ignition coil 1 | ignition_out | MAXXECURACE-C1-A2 | IGN 1 | ignition_out | corroborated | |
| OEM-X60005-5 | Ignition ground | ground | MAXXECURACE-C1-L4 + MAXXECURACE-C2-G4 | Engine GND + ENGINE GROUND | ground | corroborated | |
| OEM-X60005-7 | Ignition coil 6 | ignition_out | MAXXECURACE-C1-C3 | IGN 6 | ignition_out | corroborated | |
| OEM-X60005-8 | Ignition coil 5 | ignition_out | MAXXECURACE-C1-C2 | IGN 5 | ignition_out | corroborated | |
| OEM-X60005-9 | Ignition coil 4 | ignition_out | MAXXECURACE-C1-B3 | IGN 4 | ignition_out | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-X60001-8 | SP-14V-1 | 0.85 | no route | ECU main power (terminal 87 via main relay) | — | |
| W2 | OEM-X60001-9 | SP-14V-1 | 0.85 | no route | Voltage supply (injector / fuse carrier) | — | |
| W3 | SP-14V-1 | MAXXECURACE-C1-M4 | 0.85 | no route | +12V ECU power supply | — | |
| W4 | OEM-X60001-4 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W5 | OEM-X60001-5 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W6 | OEM-X60001-6 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W7 | OEM-X60005-5 | SP-GND-1 | 0.85 | no route | Ignition ground | — | |
| W8 | SP-GND-1 | MAXXECURACE-C1-L4 | 0.85 | no route | Engine GND | — | |
| W9 | SP-GND-1 | MAXXECURACE-C2-G4 | 0.85 | no route | ENGINE GROUND | — | |
| W10 | OEM-X60002-20 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 1 pre-cat | — | |
| W11 | OEM-X60002-21 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 2 pre-cat | — | |
| W12 | OEM-X60002-22 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 1 post-cat | — | |
| W13 | OEM-X60002-24 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 2 post-cat | — | |
| W14 | OEM-X60003-15 | SP-0V-1 | 0.5 | no route | Exhaust camshaft ground | — | |
| W15 | OEM-X60003-17 | SP-0V-1 | 0.5 | no route | MAF ground | — | |
| W16 | OEM-X60003-18 | SP-0V-1 | 0.5 | no route | Intake camshaft ground | — | |
| W17 | OEM-X60003-20 | SP-0V-1 | 0.5 | no route | Throttle ground | — | |
| W18 | OEM-X60003-21 | SP-0V-1 | 0.5 | no route | Crankshaft ground | — | |
| W19 | OEM-X60003-23 | SP-0V-1 | 0.5 | no route | IAT ground | — | |
| W20 | OEM-X60003-25 | SP-0V-1 | 0.5 | no route | ECT ground | — | |
| W21 | OEM-X60003-28 | SP-0V-1 | 0.5 | no route | Oil temperature ground | — | |
| W22 | OEM-X60004-12 | SP-0V-1 | 0.5 | no route | Pedal ground 2 | — | |
| W23 | OEM-X60004-7 | SP-0V-1 | 0.5 | no route | Pedal ground 1 | — | |
| W24 | SP-0V-1 | MAXXECURACE-C1-H1 | 0.5 | no route | Sensor GND | — | |
| W25 | SP-0V-1 | MAXXECURACE-C1-H2 | 0.5 | no route | Trigger GND | — | |
| W26 | OEM-X60003-7 | SP-5V1-1 | 0.5 | no route | Throttle body +5V supply | — | |
| W27 | OEM-X60004-14 | SP-5V1-1 | 0.5 | no route | Pedal +5V supply 2 | — | |
| W28 | OEM-X60004-9 | SP-5V1-1 | 0.5 | no route | Pedal +5V supply 1 | — | |
| W29 | SP-5V1-1 | MAXXECURACE-C1-G1 | 0.5 | no route | +5V sensor supply | — | |
| W30 | OEM-X60003-8 | MAXXECURACE-C1-H3 | 0.5 | no route | Crankshaft position | — | |
| W31 | OEM-X60003-2 | MAXXECURACE-C1-H4 | 0.5 | no route | Exhaust camshaft position | — | |
| W32 | OEM-X60003-29 | MAXXECURACE-C2-E2 | 0.5 | no route | Knock sensor, cylinders 1-3 (A) | — | |
| W33 | OEM-X60003-30 | MAXXECURACE-C2-E3 | 0.5 | no route | Knock sensor, cylinders 1-3 (B) | — | |
| W34 | OEM-X60005-3 | MAXXECURACE-C1-A2 | 0.5 | no route | Ignition coil 1 | — | |
| W35 | OEM-X60005-2 | MAXXECURACE-C1-A3 | 0.5 | no route | Ignition coil 2 | — | |
| W36 | OEM-X60005-1 | MAXXECURACE-C1-B2 | 0.5 | no route | Ignition coil 3 | — | |
| W37 | OEM-X60005-9 | MAXXECURACE-C1-B3 | 0.5 | no route | Ignition coil 4 | — | |
| W38 | OEM-X60005-8 | MAXXECURACE-C1-C2 | 0.5 | no route | Ignition coil 5 | — | |
| W39 | OEM-X60005-7 | MAXXECURACE-C1-C3 | 0.5 | no route | Ignition coil 6 | — | |
| W40 | OEM-X60003-33 | MAXXECURACE-C1-K1 | 0.5 | no route | Injector cylinder 1 | — | |
| W41 | OEM-X60003-34 | MAXXECURACE-C1-K2 | 0.5 | no route | Injector cylinder 2 | — | |
| W42 | OEM-X60003-35 | MAXXECURACE-C1-M1 | 0.5 | no route | Injector cylinder 3 | — | |
| W43 | OEM-X60003-36 | MAXXECURACE-C1-M2 | 0.5 | no route | Injector cylinder 4 | — | |
| W44 | OEM-X60003-37 | MAXXECURACE-C1-M3 | 0.5 | no route | Injector cylinder 5 | — | |
| W45 | OEM-X60003-38 | MAXXECURACE-C1-L3 | 0.5 | no route | Injector cylinder 6 | — | |
| W46 | OEM-X60003-48 | SP-SHD-1 | 0.5 | no route | Knock sensor shield | — | |
| W47 | SP-SHD-1 | MAXXECURACE-C1-E3 | 0.5 | no route | GND Shield | — | |
| W48 | OEM-X60003-43 | MAXXECURACE-C2-H2 | 0.5 | no route | Throttle motor drive 1 (H-bridge) | — | |
| W49 | OEM-X60003-44 | MAXXECURACE-C2-H4 | 0.5 | no route | Throttle motor drive 2 (H-bridge) | — | |
| W50 | OEM-X60003-46 | MAXXECURACE-C2-H1 | 0.5 | no route | Idle speed control, close | — | |
| W51 | OEM-X60003-47 | MAXXECURACE-C2-H3 | 0.5 | no route | Idle speed control, open | — | |
| W52 | OEM-X60001-1 | MAXXECURACE-C1-B4 | 0.5 | no route | Injector/unloader relay control (terminal 15) | — | |
| W53 | OEM-X60002-23 | MAXXECURACE-C1-C4 | 0.5 | no route | Main relay control | — | |
| W54 | OEM-X60004-10 | MAXXECURACE-C1-D4 | 0.5 | no route | Fuel pump relay control | — | |
| W55 | OEM-X60002-1 | MAXXECURACE-C1-D1 | 0.5 | no route | O2 sensor heater, bank 1 pre-cat | — | |
| W56 | OEM-X60002-13 | MAXXECURACE-C1-E4 | 0.5 | no route | O2 sensor heater, bank 2 pre-cat | — | |
| W57 | OEM-X60002-19 | MAXXECURACE-C1-A1 | 0.5 | no route | O2 sensor heater, bank 2 post-cat | — | |
| W58 | OEM-X60002-7 | MAXXECURACE-C1-B1 | 0.5 | no route | O2 sensor heater, bank 1 post-cat | — | |
| W59 | OEM-X60003-40 | MAXXECURACE-C1-C1 | 0.5 | no route | VANOS intake solenoid | — | |
| W60 | OEM-X60003-41 | MAXXECURACE-C1-A4 | 0.5 | no route | VANOS exhaust solenoid | — | |
| W61 | OEM-X60003-42 | MAXXECURACE-C1-L2 | 0.5 | no route | Evap purge valve | — | |
| W62 | OEM-X60003-45 | MAXXECURACE-C1-L1 | 0.5 | no route | Map-controlled thermostat | — | |
| W63 | OEM-X60003-1 | MAXXECURACE-C1-J3 | 0.5 | no route | Mass air flow (MAF) signal | — | |
| W64 | OEM-X60003-19 | MAXXECURACE-C1-G2 | 0.5 | no route | Throttle position sensor 1 | — | |
| W65 | OEM-X60004-8 | MAXXECURACE-C1-J4 | 0.5 | no route | Pedal position signal 1 | — | |
| W66 | OEM-X60003-10 | MAXXECURACE-C2-G3 | 0.5 | no route | Throttle position sensor 2 | — | |
| W67 | OEM-X60004-13 | MAXXECURACE-C2-E4 | 0.5 | no route | Pedal position signal 2 | — | |
| W68 | OEM-X60002-14 | MAXXECURACE-C2-F1 | 0.5 | no route | O2 sensor signal, bank 1 pre-cat | — | |
| W69 | OEM-X60002-15 | MAXXECURACE-C2-F2 | 0.5 | no route | O2 sensor signal, bank 2 pre-cat | — | |
| W70 | OEM-X60003-24 | MAXXECURACE-C1-J1 | 0.5 | no route | Engine coolant temperature (ECT) | — | |
| W71 | OEM-X60003-22 | MAXXECURACE-C1-J2 | 0.5 | no route | Intake air temperature (IAT) | — | |
| W72 | OEM-X60003-27 | MAXXECURACE-C1-F1 | 0.5 | no route | Engine oil temperature | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | BMW-E46-MS43-CONN | BMW | E46 DME (MS43) harness connector | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (6)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | REQUIRED_UNMAPPED | OEM-X60003-5 | Required OEM function "Intake camshaft position" (trigger_in) is not connected to the new ECU. |
| warn | DBW_MOTOR_CURRENT | MAXXECURACE-C2-H2 | Cannot confirm MaxxECU RACE can drive the throttle motor: MAXXECURACE-C2-H2 "MOTOR 1-" is rated 2.0 A, but the motor current at OEM-X60003-43 is unknown. Add the motor's peak current from a source, or measure the motor resistance: peak ≈ 14 V ÷ R (Hondata measured 4.9 A for a Civic Si body, 10.4 A for a ZDX body; holding current is about 1 A). |
| warn | DBW_MOTOR_CURRENT | MAXXECURACE-C2-H4 | Cannot confirm MaxxECU RACE can drive the throttle motor: MAXXECURACE-C2-H4 "MOTOR 1+" is rated 2.0 A, but the motor current at OEM-X60003-44 is unknown. Add the motor's peak current from a source, or measure the motor resistance: peak ≈ 14 V ÷ R (Hondata measured 4.9 A for a Civic Si body, 10.4 A for a ZDX body; holding current is about 1 A). |
| info | NET_FAMILY | OEM-X60003-42 ↔ MAXXECURACE-C1-L2 | OEM-X60003-42 "Evap purge valve" [low_side_out] is wired to MAXXECURACE-C1-L2 "INJ 7" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-X60003-45 ↔ MAXXECURACE-C1-L1 | OEM-X60003-45 "Map-controlled thermostat" [low_side_out] is wired to MAXXECURACE-C1-L1 "INJ 8" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | UNMAPPED | OEM | 5 optional OEM pins are not mapped: OEM-X60002-16 O2 sensor signal, bank 1 post-cat; OEM-X60002-18 O2 sensor signal, bank 2 post-cat; OEM-X60003-31 Knock sensor, cylinders 4-6 (A); OEM-X60003-32 Knock sensor, cylinders 4-6 (B); OEM-X60003-49 DISA intake flap |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-X60001-7 | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
Notes
Fit check: unconfirmed. Confirm these before building: - Needs CAN (E46 K-bus/CAN); not documented for this ECU - This car has EWS 3.3 (rolling code) immobilizer; needs a delete/bypass Auto-mapped by auto_map() from the library pin data on 2026-10-06. Review every wire against both manuals before building. Open items: - OEM-X60003 5: Intake camshaft position: no free cam_hall/cam_vr/frequency_in input on MaxxECU MaxxECU RACE Not wired: - OEM-X60001 7: Battery constant (terminal 30): MaxxECU MaxxECU RACE has no battery-constant input; not needed - OEM-X60003 31: Knock sensor, cylinders 4-6 (A): no free knock input on MaxxECU MaxxECU RACE - OEM-X60003 32: Knock sensor, cylinders 4-6 (B): no free knock input on MaxxECU MaxxECU RACE - OEM-X60003 49: DISA intake flap: no free low_side/ls_hs/injector/hbridge on MaxxECU MaxxECU RACE - OEM-X60002 16: O2 sensor signal, bank 1 post-cat: no free o2_narrowband/analog_0_5 on MaxxECU MaxxECU RACE - OEM-X60002 18: O2 sensor signal, bank 2 post-cat: no free o2_narrowband/analog_0_5 on MaxxECU MaxxECU RACE
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | MaxxECU GEN1 pinout (MINI / STREET / SPORT / V1 / RACE / PRO) | http://www.maxxecu.com/webhelp/wirings-maxxecu_pinout.html | archive | 2026-10-05 | 2e37b6814690 |
| 2 | community_copy | ms4x.net: Siemens MS43 Pinout | https://www.ms4x.net/index.php?title=Siemens_MS43_Pinout | — | — | — |
| 2 | community_copy | rusefi wiki: 2002 BMW 325 / 2004 BMW 330Ci E46 DME pinout (M54/MS43) | https://github.com/rusefi/rusefi/wiki/2002-BMW-325-and-2004-BMW-330Ci-E46-DME-pinout | — | — | — |