Chevrolet Camaro SS 2010-15 (LS3/L99) → Emtron Shadow 8 (auto)
Chevrolet Camaro SS 2010-15 (LS3/L99) — Emtron — Shadow 8
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-08
Before you start
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 2: read the Findings page before cutting any wire |
| Size of the job | 82 wires · 8 connectors · 3 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Terminals | 3-1447221-4 |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-X1-19 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-X1-47 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | SHADOW8-A-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | SP-14V-1 | SHADOW8-B-26 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-X1-20 | SHADOW8-B-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-X1-73 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-X2-78 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-X2-79 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | SHADOW8-A-34 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | SP-GND-1 | SHADOW8-A-9 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-X1-11 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-X1-23 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-X1-30 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-X1-38 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-X1-49 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-X2-22 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-X2-34 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-X2-35 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-X2-52 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-X2-53 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-X2-56 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-X2-60 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-X2-66 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-X2-69 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | SP-0V-1 | SHADOW8-A-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | SP-0V-1 | SHADOW8-A-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-X1-33 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-X1-34 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-X1-36 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-X1-56 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-X2-2 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-X2-3 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-X2-41 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-X2-43 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-X2-44 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | SP-5V1-1 | SHADOW8-A-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-X2-68 | SHADOW8-A-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-X2-64 | SHADOW8-A-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-X2-26 | SHADOW8-A-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-X2-27 | SHADOW8-A-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-X2-70 | SHADOW8-B-27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-X2-73 | SHADOW8-B-28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-X2-77 | SHADOW8-B-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-X2-76 | SHADOW8-B-30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-X2-75 | SHADOW8-B-31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-X2-74 | SHADOW8-B-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | OEM-X2-72 | SHADOW8-B-33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | OEM-X2-71 | SHADOW8-B-34 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W49 | OEM-X2-20 | SHADOW8-B-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W50 | OEM-X2-37 | SHADOW8-B-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W51 | OEM-X2-38 | SHADOW8-B-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W52 | OEM-X2-39 | SHADOW8-B-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W53 | OEM-X2-18 | SHADOW8-B-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W54 | OEM-X2-19 | SHADOW8-B-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W55 | OEM-X2-40 | SHADOW8-B-8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W56 | OEM-X2-17 | SHADOW8-B-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W57 | OEM-X2-6 | SHADOW8-B-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W58 | OEM-X2-5 | SHADOW8-B-23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W59 | OEM-X1-50 | SHADOW8-B-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W60 | OEM-X1-59 | SHADOW8-B-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W61 | OEM-X1-17 | SHADOW8-B-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W62 | OEM-X1-51 | SHADOW8-B-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W63 | OEM-X1-52 | SHADOW8-B-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W64 | OEM-X1-58 | SHADOW8-B-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W65 | OEM-X1-63 | SHADOW8-B-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W66 | OEM-X1-64 | SHADOW8-B-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W67 | OEM-X1-65 | SHADOW8-B-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W68 | OEM-X2-12 | SHADOW8-B-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W69 | OEM-X1-41 | SHADOW8-A-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W70 | OEM-X2-58 | SHADOW8-A-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W71 | OEM-X1-29 | SHADOW8-A-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W72 | OEM-X2-65 | SHADOW8-A-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W73 | OEM-X1-32 | SHADOW8-A-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W74 | OEM-X2-63 | SHADOW8-A-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W75 | OEM-X1-10 | SHADOW8-A-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W76 | OEM-X1-69 | SHADOW8-A-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W77 | OEM-X2-57 | SHADOW8-A-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W78 | OEM-X2-59 | SHADOW8-A-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W79 | OEM-X1-71 | SHADOW8-A-26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W80 | OEM-X1-72 | SHADOW8-A-27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W81 | OEM-X1-9 | SHADOW8-A-28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W82 | OEM-X2-33 | SHADOW8-A-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | SHADOW8-A-1 | SHADOW8-A-34 | open (OL) | +12 V supply must not touch power ground | |
| 2 | SHADOW8-A-3 | SHADOW8-A-34 | open (OL) | 5 V sensor reference must not touch power ground | |
| 3 | SHADOW8-B-1 | SHADOW8-A-34 | open (OL) | +12 V supply must not touch power ground | |
| 4 | SHADOW8-A-1 | SHADOW8-A-3 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 5 | SHADOW8-A-4 | SHADOW8-A-1 | open (OL) | sensor ground must not touch +12 V supply | |
| 6 | SHADOW8-A-4 | SHADOW8-A-3 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 7 | SHADOW8-A-4 | SHADOW8-B-1 | open (OL) | sensor ground must not touch +12 V supply | |
| 8 | SHADOW8-B-1 | SHADOW8-A-3 | open (OL) | +12 V supply must not touch 5 V sensor reference |
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
OEM-X1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | HO2S signal, bank 1 sensor 2 (post-cat) | — | W75 | — | 0.5 | SHADOW8-A-19 | — | — | — |
| 11 | HO2S low reference, bank 1 sensor 2 | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| 12 | A/C refrigerant pressure signal | — | — | — | — | — | — | — | — |
| 17 | High speed cooling fan relay | — | W61 | — | 0.5 | SHADOW8-B-12 | — | — | — |
| 19 | Ignition 1 voltage (key hot) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 20 | Battery positive voltage (batt hot) | — | W5 | — | 0.85 | SHADOW8-B-1 | — | — | — |
| 23 | APP sensor low reference | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | Fuel tank pressure signal | — | — | — | — | — | — | — | — |
| 29 | Accelerator pedal position (APP) sensor 1 signal | — | W71 | — | 0.5 | SHADOW8-A-12 | — | — | — |
| 30 | APP sensor low reference | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 32 | Accelerator pedal position (APP) sensor 2 signal | — | W73 | — | 0.5 | SHADOW8-A-14 | — | — | — |
| 33 | 5V reference (fuel tank pressure) | — | W27 | — | 0.5 | SP-5V1-1 | — | — | — |
| 34 | 5V reference (A/C pressure) | — | W28 | — | 0.5 | SP-5V1-1 | — | — | — |
| 36 | 5V reference (APP sensor) | — | W29 | — | 0.5 | SP-5V1-1 | — | — | — |
| 37 | Intake air temperature (IAT) signal | — | — | — | — | — | — | — | — |
| 38 | Intake air temperature (IAT) low reference | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 41 | Mass air flow (MAF) signal | — | W69 | — | 0.5 | SHADOW8-A-10 | — | — | — |
| 47 | Ignition 1 voltage (key hot) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 48 | Tachometer output | — | — | — | — | — | — | — | — |
| 49 | HO2S low reference, bank 2 sensor 2 | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 50 | Fuel pump relay control (primary) | — | W59 | — | 0.5 | SHADOW8-B-10 | — | — | — |
| 51 | Fuel pump relay control (secondary) | — | W62 | — | 0.5 | SHADOW8-B-13 | — | — | — |
| 52 | Starter enable relay control | — | W63 | — | 0.5 | SHADOW8-B-14 | — | — | — |
| 56 | 5V reference (APP sensor) | — | W30 | — | 0.5 | SP-5V1-1 | — | — | — |
| 57 | VSS output to ABS (128k) | — | — | — | — | — | — | — | — |
| 58 | Low speed cooling fan relay | — | W64 | — | 0.5 | SHADOW8-B-15 | — | — | — |
| 59 | Powertrain relay coil control (main relay) | — | W60 | — | 0.5 | SHADOW8-B-11 | — | — | — |
| 61 | EVAP canister vent solenoid | — | — | — | — | — | — | — | — |
| 63 | A/C compressor clutch relay | — | W65 | — | 0.5 | SHADOW8-B-16 | — | — | — |
| 64 | HO2S heater low control, bank 2 sensor 2 | — | W66 | — | 0.5 | SHADOW8-B-17 | — | — | — |
| 65 | HO2S heater low control, bank 1 sensor 2 | — | W67 | — | 0.5 | SHADOW8-B-24 | — | — | — |
| 68 | Malfunction indicator lamp (MIL) | — | — | — | — | — | — | — | — |
| 69 | HO2S signal, bank 2 sensor 2 (post-cat) | — | W76 | — | 0.5 | SHADOW8-A-20 | — | — | — |
| 71 | VSS high signal (manual trans) | — | W79 | — | 0.5 | SHADOW8-A-26 | — | — | — |
| 72 | VSS low signal (manual trans) | — | W80 | — | 0.5 | SHADOW8-A-27 | — | — | — |
| 73 | Power ground | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 9 | Brake switch signal | — | W81 | — | 0.5 | SHADOW8-A-28 | — | — | — |
OEM-X2
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | Cylinder shutoff solenoid 1 (AFM) | — | — | — | — | — | — | — | — |
| 11 | Cylinder shutoff solenoid 4 (AFM) | — | — | — | — | — | — | — | — |
| 12 | HO2S heater low control, bank 1 sensor 1 | — | W68 | — | 0.5 | SHADOW8-B-25 | — | — | — |
| 13 | HO2S heater low control, bank 2 sensor 1 | — | — | — | — | — | — | — | — |
| 14 | Cylinder shutoff solenoid 2 (AFM) | — | — | — | — | — | — | — | — |
| 16 | Camshaft actuator solenoid (VVT) | — | — | — | — | — | — | — | — |
| 17 | Injector 8 | — | W56 | — | 0.5 | SHADOW8-B-9 | — | — | — |
| 18 | Injector 5 | — | W53 | — | 0.5 | SHADOW8-B-6 | — | — | — |
| 19 | Injector 6 | — | W54 | — | 0.5 | SHADOW8-B-7 | — | — | — |
| 2 | 5V reference (crankshaft sensor) | — | W31 | — | 0.5 | SP-5V1-1 | — | — | — |
| 20 | Injector 1 | — | W49 | — | 0.5 | SHADOW8-B-2 | — | — | — |
| 21 | Engine coolant temperature (ECT) signal | — | — | — | — | — | — | — | — |
| 22 | ECT low reference | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 26 | Knock sensor 1 signal A | — | W39 | — | 0.5 | SHADOW8-A-16 | — | — | — |
| 27 | Knock sensor 1 signal B | — | W40 | — | 0.5 | SHADOW8-A-24 | — | — | — |
| 29 | Knock sensor 2 signal A | — | — | — | — | — | — | — | — |
| 3 | 5V reference (throttle body) | — | W32 | — | 0.5 | SP-5V1-1 | — | — | — |
| 30 | Knock sensor 2 signal B | — | — | — | — | — | — | — | — |
| 32 | Generator field duty control | — | — | — | — | — | — | — | — |
| 33 | Oil level switch signal | — | W82 | — | 0.5 | SHADOW8-A-29 | — | — | — |
| 34 | Oil pressure low reference | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 35 | Throttle body low reference | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 37 | Injector 2 | — | W50 | — | 0.5 | SHADOW8-B-3 | — | — | — |
| 38 | Injector 3 | — | W51 | — | 0.5 | SHADOW8-B-4 | — | — | — |
| 39 | Injector 4 | — | W52 | — | 0.5 | SHADOW8-B-5 | — | — | — |
| 40 | Injector 7 | — | W55 | — | 0.5 | SHADOW8-B-8 | — | — | — |
| 41 | 5V reference (oil pressure) | — | W33 | — | 0.5 | SP-5V1-1 | — | — | — |
| 43 | 5V reference (MAP) | — | W34 | — | 0.5 | SP-5V1-1 | — | — | — |
| 44 | 5V reference (camshaft sensor) | — | W35 | — | 0.5 | SP-5V1-1 | — | — | — |
| 5 | Throttle actuator motor control 2 | — | W58 | — | 0.5 | SHADOW8-B-23 | — | — | — |
| 50 | Engine oil pressure signal | — | — | — | — | — | — | — | — |
| 52 | Camshaft actuator low reference | — | W19 | — | 0.5 | SP-0V-1 | — | — | — |
| 53 | MAP low reference | — | W20 | — | 0.5 | SP-0V-1 | — | — | — |
| 56 | HO2S low reference, bank 1 sensor 1 | — | W21 | — | 0.5 | SP-0V-1 | — | — | — |
| 57 | HO2S signal, bank 1 sensor 1 (pre-cat) | — | W77 | — | 0.5 | SHADOW8-A-21 | — | — | — |
| 58 | Manifold absolute pressure (MAP) signal | — | W70 | — | 0.5 | SHADOW8-A-11 | — | — | — |
| 59 | HO2S signal, bank 2 sensor 1 (pre-cat) | — | W78 | — | 0.5 | SHADOW8-A-22 | — | — | — |
| 6 | Throttle actuator motor control 1 | — | W57 | — | 0.5 | SHADOW8-B-22 | — | — | — |
| 60 | HO2S low reference, bank 2 sensor 1 | — | W22 | — | 0.5 | SP-0V-1 | — | — | — |
| 61 | Charge indicator signal | — | — | — | — | — | — | — | — |
| 63 | Throttle position sensor 2 signal | — | W74 | — | 0.5 | SHADOW8-A-18 | — | — | — |
| 64 | Camshaft position signal (4x) | — | W38 | — | 0.5 | SHADOW8-A-6 | — | — | — |
| 65 | Throttle position sensor 1 signal | — | W72 | — | 0.5 | SHADOW8-A-13 | — | — | — |
| 66 | Camshaft position low reference | — | W23 | — | 0.5 | SP-0V-1 | — | — | — |
| 68 | Crankshaft position signal (58x) | — | W37 | — | 0.5 | SHADOW8-A-5 | — | — | — |
| 69 | Crankshaft position low reference | — | W24 | — | 0.5 | SP-0V-1 | — | — | — |
| 70 | Ignition coil 1 control | — | W41 | — | 0.5 | SHADOW8-B-27 | — | — | — |
| 71 | Ignition coil 8 control | — | W48 | — | 0.5 | SHADOW8-B-34 | — | — | — |
| 72 | Ignition coil 7 control | — | W47 | — | 0.5 | SHADOW8-B-33 | — | — | — |
| 73 | Ignition coil 2 control | — | W42 | — | 0.5 | SHADOW8-B-28 | — | — | — |
| 74 | Ignition coil 6 control | — | W46 | — | 0.5 | SHADOW8-B-32 | — | — | — |
| 75 | Ignition coil 5 control | — | W45 | — | 0.5 | SHADOW8-B-31 | — | — | — |
| 76 | Ignition coil 4 control | — | W44 | — | 0.5 | SHADOW8-B-30 | — | — | — |
| 77 | Ignition coil 3 control | — | W43 | — | 0.5 | SHADOW8-B-29 | — | — | — |
| 78 | Coil low reference (odd bank) | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 79 | Coil low reference (even bank) | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 8 | EVAP canister purge solenoid | — | — | — | — | — | — | — | — |
| 9 | Cylinder shutoff solenoid 3 (AFM) | — | — | — | — | — | — | — | — |
SHADOW8-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | ECU supply | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 2 | 8.0V sensor supply | — | — | — | — | — | — | — | — |
| 3 | 5.0V sensor supply | — | W36 | — | 0.5 | SP-5V1-1 | — | — | — |
| 4 | 0V analog reference | — | W25 | — | 0.5 | SP-0V-1 | — | — | — |
| 5 | Crank position sensor | — | W37 | — | 0.5 | OEM-X2-68 | — | — | — |
| 6 | Sync position sensor | — | W38 | — | 0.5 | OEM-X2-64 | — | — | — |
| 7 | Trigger ground | — | W26 | — | 0.5 | SP-0V-1 | — | — | — |
| 8 | Shield | — | — | — | — | — | — | — | — |
| 9 | Ground 1 | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 10 | Analog voltage 1 | — | W69 | — | 0.5 | OEM-X1-41 | — | — | — |
| 11 | Analog voltage 2 | — | W70 | — | 0.5 | OEM-X2-58 | — | — | — |
| 12 | Analog voltage 3 | — | W71 | — | 0.5 | OEM-X1-29 | — | — | — |
| 13 | Analog voltage 4 | — | W72 | — | 0.5 | OEM-X2-65 | — | — | — |
| 14 | Analog voltage 5 | — | W73 | — | 0.5 | OEM-X1-32 | — | — | — |
| 15 | CAN bus 1 high | — | — | — | — | — | — | — | — |
| 16 | Knock 1 + | — | W39 | — | 0.5 | OEM-X2-26 | — | — | — |
| 17 | Knock 1 − | — | — | — | — | — | — | — | — |
| 18 | Analog voltage 6 | — | W74 | — | 0.5 | OEM-X2-63 | — | — | — |
| 19 | Analog voltage 7 (switchable 1k pull-up) | — | W75 | — | 0.5 | OEM-X1-10 | — | — | — |
| 20 | Analog voltage 8 (switchable 1k pull-up) | — | W76 | — | 0.5 | OEM-X1-69 | — | — | — |
| 21 | Analog voltage 9 (switchable 1k pull-up) | — | W77 | — | 0.5 | OEM-X2-57 | — | — | — |
| 22 | Analog voltage 10 (switchable 1k pull-up) | — | W78 | — | 0.5 | OEM-X2-59 | — | — | — |
| 23 | CAN bus 1 low | — | — | — | — | — | — | — | — |
| 24 | Knock 2 + | — | W40 | — | 0.5 | OEM-X2-27 | — | — | — |
| 25 | Knock 2 − | — | — | — | — | — | — | — | — |
| 26 | Digital input 1 | — | W79 | — | 0.5 | OEM-X1-71 | — | — | — |
| 27 | Digital input 2 | — | W80 | — | 0.5 | OEM-X1-72 | — | — | — |
| 28 | Digital input 3 | — | W81 | — | 0.5 | OEM-X1-9 | — | — | — |
| 29 | Digital input 4 | — | W82 | — | 0.5 | OEM-X2-33 | — | — | — |
| 30 | Digital input 5 | — | — | — | — | — | — | — | — |
| 31 | Digital input 6 | — | — | — | — | — | — | — | — |
| 32 | CAN bus 2 high | — | — | — | — | — | — | — | — |
| 33 | CAN bus 2 low | — | — | — | — | — | — | — | — |
| 34 | Ground 2 | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
SHADOW8-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Battery constant (HOT) supply | — | W5 | — | 0.85 | OEM-X1-20 | — | — | — |
| 2 | Injector cylinder 1 | — | W49 | — | 0.5 | OEM-X2-20 | — | — | — |
| 3 | Injector cylinder 2 | — | W50 | — | 0.5 | OEM-X2-37 | — | — | — |
| 4 | Injector cylinder 3 | — | W51 | — | 0.5 | OEM-X2-38 | — | — | — |
| 5 | Injector cylinder 4 | — | W52 | — | 0.5 | OEM-X2-39 | — | — | — |
| 6 | Injector cylinder 5 | — | W53 | — | 0.5 | OEM-X2-18 | — | — | — |
| 7 | Injector cylinder 6 | — | W54 | — | 0.5 | OEM-X2-19 | — | — | — |
| 8 | Injector cylinder 7 | — | W55 | — | 0.5 | OEM-X2-40 | — | — | — |
| 9 | Injector cylinder 8 | — | W56 | — | 0.5 | OEM-X2-17 | — | — | — |
| 10 | Aux output 1 | — | W59 | — | 0.5 | OEM-X1-50 | — | — | — |
| 11 | Aux output 2 | — | W60 | — | 0.5 | OEM-X1-59 | — | — | — |
| 12 | Aux output 3 | — | W61 | — | 0.5 | OEM-X1-17 | — | — | — |
| 13 | Aux output 4 | — | W62 | — | 0.5 | OEM-X1-51 | — | — | — |
| 14 | Aux output 5 | — | W63 | — | 0.5 | OEM-X1-52 | — | — | — |
| 15 | Aux output 6 | — | W64 | — | 0.5 | OEM-X1-58 | — | — | — |
| 16 | Aux output 7 | — | W65 | — | 0.5 | OEM-X1-63 | — | — | — |
| 17 | Aux output 8 | — | W66 | — | 0.5 | OEM-X1-64 | — | — | — |
| 18 | Digital input 7 | — | — | — | — | — | — | — | — |
| 19 | Digital input 8 | — | — | — | — | — | — | — | — |
| 20 | Digital input 9 | — | — | — | — | — | — | — | — |
| 21 | Digital input 10 / ignition switch | — | — | — | — | — | — | — | — |
| 22 | Aux output 9 | — | W57 | — | 0.5 | OEM-X2-6 | — | — | — |
| 23 | Aux output 10 | — | W58 | — | 0.5 | OEM-X2-5 | — | — | — |
| 24 | Aux output 11 | — | W67 | — | 0.5 | OEM-X1-65 | — | — | — |
| 25 | Aux output 12 | — | W68 | — | 0.5 | OEM-X2-12 | — | — | — |
| 26 | Aux 9–12 power supply | — | W4 | — | 0.85 | SP-14V-1 | — | — | — |
| 27 | Ignition TTL cylinder 1 | — | W41 | — | 0.5 | OEM-X2-70 | — | — | — |
| 28 | Ignition TTL cylinder 2 | — | W42 | — | 0.5 | OEM-X2-73 | — | — | — |
| 29 | Ignition TTL cylinder 3 | — | W43 | — | 0.5 | OEM-X2-77 | — | — | — |
| 30 | Ignition TTL cylinder 4 | — | W44 | — | 0.5 | OEM-X2-76 | — | — | — |
| 31 | Ignition TTL cylinder 5 | — | W45 | — | 0.5 | OEM-X2-75 | — | — | — |
| 32 | Ignition TTL cylinder 6 | — | W46 | — | 0.5 | OEM-X2-74 | — | — | — |
| 33 | Ignition TTL cylinder 7 | — | W47 | — | 0.5 | OEM-X2-72 | — | — | — |
| 34 | Ignition TTL cylinder 8 | — | W48 | — | 0.5 | OEM-X2-71 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W25 | — | 0.5 | SHADOW8-A-4 | — | — | — |
| 1 | — | — | W11 | — | 0.5 | OEM-X1-11 | — | — | — |
| 1 | — | — | W12 | — | 0.5 | OEM-X1-23 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | OEM-X1-30 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | OEM-X1-38 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | OEM-X1-49 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-X2-22 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | OEM-X2-34 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | OEM-X2-35 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | OEM-X2-52 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | OEM-X2-53 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | OEM-X2-56 | — | — | — |
| 1 | — | — | W22 | — | 0.5 | OEM-X2-60 | — | — | — |
| 1 | — | — | W23 | — | 0.5 | OEM-X2-66 | — | — | — |
| 1 | — | — | W24 | — | 0.5 | OEM-X2-69 | — | — | — |
| 1 | — | — | W26 | — | 0.5 | SHADOW8-A-7 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-X1-19 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-X1-47 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | SHADOW8-A-1 | — | — | — |
| 1 | — | — | W4 | — | 0.85 | SHADOW8-B-26 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W27 | — | 0.5 | OEM-X1-33 | — | — | — |
| 1 | — | — | W28 | — | 0.5 | OEM-X1-34 | — | — | — |
| 1 | — | — | W29 | — | 0.5 | OEM-X1-36 | — | — | — |
| 1 | — | — | W30 | — | 0.5 | OEM-X1-56 | — | — | — |
| 1 | — | — | W31 | — | 0.5 | OEM-X2-2 | — | — | — |
| 1 | — | — | W32 | — | 0.5 | OEM-X2-3 | — | — | — |
| 1 | — | — | W33 | — | 0.5 | OEM-X2-41 | — | — | — |
| 1 | — | — | W34 | — | 0.5 | OEM-X2-43 | — | — | — |
| 1 | — | — | W35 | — | 0.5 | OEM-X2-44 | — | — | — |
| 1 | — | — | W36 | — | 0.5 | SHADOW8-A-3 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W6 | — | 0.85 | OEM-X1-73 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-X2-78 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | OEM-X2-79 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | SHADOW8-A-34 | — | — | — |
| 1 | — | — | W10 | — | 0.85 | SHADOW8-A-9 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-X1-10 | HO2S signal, bank 1 sensor 2 (post-cat) | lambda_nb_in | SHADOW8-A-19 | Analog voltage 7 (switchable 1k pull-up) | analog_in | single_source | |
| OEM-X1-11 | HO2S low reference, bank 1 sensor 2 | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X1-12 | A/C refrigerant pressure signal | analog_in | — | — | — | corroborated | |
| OEM-X1-17 | High speed cooling fan relay | low_side_out | SHADOW8-B-12 | Aux output 3 | low_side_out | corroborated | |
| OEM-X1-19 | Ignition 1 voltage (key hot) | power_in | SHADOW8-A-1 + SHADOW8-B-26 | ECU supply + Aux 9–12 power supply | power_in | single_source | |
| OEM-X1-20 | Battery positive voltage (batt hot) | power_in | SHADOW8-B-1 | Battery constant (HOT) supply | power_in | single_source | |
| OEM-X1-23 | APP sensor low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X1-24 | Fuel tank pressure signal | analog_in | — | — | — | corroborated | |
| OEM-X1-29 | Accelerator pedal position (APP) sensor 1 signal | analog_in | SHADOW8-A-12 | Analog voltage 3 | analog_in | single_source | |
| OEM-X1-30 | APP sensor low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X1-32 | Accelerator pedal position (APP) sensor 2 signal | analog_in | SHADOW8-A-14 | Analog voltage 5 | analog_in | single_source | |
| OEM-X1-33 | 5V reference (fuel tank pressure) | vref | SHADOW8-A-3 | 5.0V sensor supply | vref | single_source | |
| OEM-X1-34 | 5V reference (A/C pressure) | vref | SHADOW8-A-3 | 5.0V sensor supply | vref | single_source | |
| OEM-X1-36 | 5V reference (APP sensor) | vref | SHADOW8-A-3 | 5.0V sensor supply | vref | single_source | |
| OEM-X1-37 | Intake air temperature (IAT) signal | temp_in | — | — | — | corroborated | |
| OEM-X1-38 | Intake air temperature (IAT) low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X1-41 | Mass air flow (MAF) signal | analog_in | SHADOW8-A-10 | Analog voltage 1 | analog_in | corroborated | |
| OEM-X1-47 | Ignition 1 voltage (key hot) | power_in | SHADOW8-A-1 + SHADOW8-B-26 | ECU supply + Aux 9–12 power supply | power_in | single_source | |
| OEM-X1-48 | Tachometer output | tacho_out | — | — | — | corroborated | |
| OEM-X1-49 | HO2S low reference, bank 2 sensor 2 | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X1-50 | Fuel pump relay control (primary) | low_side_out | SHADOW8-B-10 | Aux output 1 | low_side_out | corroborated | |
| OEM-X1-51 | Fuel pump relay control (secondary) | low_side_out | SHADOW8-B-13 | Aux output 4 | low_side_out | corroborated | |
| OEM-X1-52 | Starter enable relay control | low_side_out | SHADOW8-B-14 | Aux output 5 | switch_out | corroborated | |
| OEM-X1-56 | 5V reference (APP sensor) | vref | SHADOW8-A-3 | 5.0V sensor supply | vref | single_source | |
| OEM-X1-57 | VSS output to ABS (128k) | tacho_out | — | — | — | corroborated | |
| OEM-X1-58 | Low speed cooling fan relay | low_side_out | SHADOW8-B-15 | Aux output 6 | switch_out | corroborated | |
| OEM-X1-59 | Powertrain relay coil control (main relay) | low_side_out | SHADOW8-B-11 | Aux output 2 | low_side_out | corroborated | |
| OEM-X1-61 | EVAP canister vent solenoid | low_side_out | — | — | — | corroborated | |
| OEM-X1-63 | A/C compressor clutch relay | low_side_out | SHADOW8-B-16 | Aux output 7 | switch_out | corroborated | |
| OEM-X1-64 | HO2S heater low control, bank 2 sensor 2 | low_side_out | SHADOW8-B-17 | Aux output 8 | switch_out | single_source | |
| OEM-X1-65 | HO2S heater low control, bank 1 sensor 2 | low_side_out | SHADOW8-B-24 | Aux output 11 | hbridge_out | single_source | |
| OEM-X1-68 | Malfunction indicator lamp (MIL) | low_side_out | — | — | — | corroborated | |
| OEM-X1-69 | HO2S signal, bank 2 sensor 2 (post-cat) | lambda_nb_in | SHADOW8-A-20 | Analog voltage 8 (switchable 1k pull-up) | analog_in | single_source | |
| OEM-X1-71 | VSS high signal (manual trans) | digital_in | SHADOW8-A-26 | Digital input 1 | digital_in | corroborated | |
| OEM-X1-72 | VSS low signal (manual trans) | digital_in | SHADOW8-A-27 | Digital input 2 | digital_in | corroborated | |
| OEM-X1-73 | Power ground | ground | SHADOW8-A-34 + SHADOW8-A-9 | Ground 2 + Ground 1 | ground | single_source | |
| OEM-X1-9 | Brake switch signal | digital_in | SHADOW8-A-28 | Digital input 3 | digital_in | corroborated | |
| OEM-X2-10 | Cylinder shutoff solenoid 1 (AFM) | low_side_out | — | — | — | corroborated | |
| OEM-X2-11 | Cylinder shutoff solenoid 4 (AFM) | low_side_out | — | — | — | corroborated | |
| OEM-X2-12 | HO2S heater low control, bank 1 sensor 1 | low_side_out | SHADOW8-B-25 | Aux output 12 | hbridge_out | single_source | |
| OEM-X2-13 | HO2S heater low control, bank 2 sensor 1 | low_side_out | — | — | — | single_source | |
| OEM-X2-14 | Cylinder shutoff solenoid 2 (AFM) | low_side_out | — | — | — | corroborated | |
| OEM-X2-16 | Camshaft actuator solenoid (VVT) | low_side_out | — | — | — | corroborated | |
| OEM-X2-17 | Injector 8 | injector_out | SHADOW8-B-9 | Injector cylinder 8 | injector_out | single_source | |
| OEM-X2-18 | Injector 5 | injector_out | SHADOW8-B-6 | Injector cylinder 5 | injector_out | single_source | |
| OEM-X2-19 | Injector 6 | injector_out | SHADOW8-B-7 | Injector cylinder 6 | injector_out | single_source | |
| OEM-X2-2 | 5V reference (crankshaft sensor) | vref | SHADOW8-A-3 | 5.0V sensor supply | vref | single_source | |
| OEM-X2-20 | Injector 1 | injector_out | SHADOW8-B-2 | Injector cylinder 1 | injector_out | single_source | |
| OEM-X2-21 | Engine coolant temperature (ECT) signal | temp_in | — | — | — | corroborated | |
| OEM-X2-22 | ECT low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X2-26 | Knock sensor 1 signal A | knock_in | SHADOW8-A-16 | Knock 1 + | knock_in | corroborated | |
| OEM-X2-27 | Knock sensor 1 signal B | knock_in | SHADOW8-A-24 | Knock 2 + | knock_in | single_source | |
| OEM-X2-29 | Knock sensor 2 signal A | knock_in | — | — | — | corroborated | |
| OEM-X2-3 | 5V reference (throttle body) | vref | SHADOW8-A-3 | 5.0V sensor supply | vref | single_source | |
| OEM-X2-30 | Knock sensor 2 signal B | knock_in | — | — | — | single_source | |
| OEM-X2-32 | Generator field duty control | low_side_out | — | — | — | corroborated | |
| OEM-X2-33 | Oil level switch signal | digital_in | SHADOW8-A-29 | Digital input 4 | digital_in | corroborated | |
| OEM-X2-34 | Oil pressure low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X2-35 | Throttle body low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X2-37 | Injector 2 | injector_out | SHADOW8-B-3 | Injector cylinder 2 | injector_out | single_source | |
| OEM-X2-38 | Injector 3 | injector_out | SHADOW8-B-4 | Injector cylinder 3 | injector_out | single_source | |
| OEM-X2-39 | Injector 4 | injector_out | SHADOW8-B-5 | Injector cylinder 4 | injector_out | single_source | |
| OEM-X2-40 | Injector 7 | injector_out | SHADOW8-B-8 | Injector cylinder 7 | injector_out | single_source | |
| OEM-X2-41 | 5V reference (oil pressure) | vref | SHADOW8-A-3 | 5.0V sensor supply | vref | single_source | |
| OEM-X2-43 | 5V reference (MAP) | vref | SHADOW8-A-3 | 5.0V sensor supply | vref | single_source | |
| OEM-X2-44 | 5V reference (camshaft sensor) | vref | SHADOW8-A-3 | 5.0V sensor supply | vref | single_source | |
| OEM-X2-5 | Throttle actuator motor control 2 | hbridge_out | SHADOW8-B-23 | Aux output 10 | hbridge_out | corroborated | |
| OEM-X2-50 | Engine oil pressure signal | analog_in | — | — | — | corroborated | |
| OEM-X2-52 | Camshaft actuator low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X2-53 | MAP low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X2-56 | HO2S low reference, bank 1 sensor 1 | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X2-57 | HO2S signal, bank 1 sensor 1 (pre-cat) | lambda_nb_in | SHADOW8-A-21 | Analog voltage 9 (switchable 1k pull-up) | analog_in | single_source | |
| OEM-X2-58 | Manifold absolute pressure (MAP) signal | analog_in | SHADOW8-A-11 | Analog voltage 2 | analog_in | corroborated | |
| OEM-X2-59 | HO2S signal, bank 2 sensor 1 (pre-cat) | lambda_nb_in | SHADOW8-A-22 | Analog voltage 10 (switchable 1k pull-up) | analog_in | single_source | |
| OEM-X2-6 | Throttle actuator motor control 1 | hbridge_out | SHADOW8-B-22 | Aux output 9 | hbridge_out | corroborated | |
| OEM-X2-60 | HO2S low reference, bank 2 sensor 1 | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X2-61 | Charge indicator signal | low_side_out | — | — | — | corroborated | |
| OEM-X2-63 | Throttle position sensor 2 signal | analog_in | SHADOW8-A-18 | Analog voltage 6 | analog_in | single_source | |
| OEM-X2-64 | Camshaft position signal (4x) | trigger_in | SHADOW8-A-6 | Sync position sensor | trigger_in | single_source | |
| OEM-X2-65 | Throttle position sensor 1 signal | analog_in | SHADOW8-A-13 | Analog voltage 4 | analog_in | single_source | |
| OEM-X2-66 | Camshaft position low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X2-68 | Crankshaft position signal (58x) | trigger_in | SHADOW8-A-5 | Crank position sensor | trigger_in | single_source | |
| OEM-X2-69 | Crankshaft position low reference | sensor_ground | SHADOW8-A-4 + SHADOW8-A-7 | 0V analog reference + Trigger ground | sensor_ground | single_source | |
| OEM-X2-70 | Ignition coil 1 control | ignition_out | SHADOW8-B-27 | Ignition TTL cylinder 1 | ignition_out | single_source | |
| OEM-X2-71 | Ignition coil 8 control | ignition_out | SHADOW8-B-34 | Ignition TTL cylinder 8 | ignition_out | single_source | |
| OEM-X2-72 | Ignition coil 7 control | ignition_out | SHADOW8-B-33 | Ignition TTL cylinder 7 | ignition_out | single_source | |
| OEM-X2-73 | Ignition coil 2 control | ignition_out | SHADOW8-B-28 | Ignition TTL cylinder 2 | ignition_out | single_source | |
| OEM-X2-74 | Ignition coil 6 control | ignition_out | SHADOW8-B-32 | Ignition TTL cylinder 6 | ignition_out | single_source | |
| OEM-X2-75 | Ignition coil 5 control | ignition_out | SHADOW8-B-31 | Ignition TTL cylinder 5 | ignition_out | single_source | |
| OEM-X2-76 | Ignition coil 4 control | ignition_out | SHADOW8-B-30 | Ignition TTL cylinder 4 | ignition_out | single_source | |
| OEM-X2-77 | Ignition coil 3 control | ignition_out | SHADOW8-B-29 | Ignition TTL cylinder 3 | ignition_out | single_source | |
| OEM-X2-78 | Coil low reference (odd bank) | ground | SHADOW8-A-34 + SHADOW8-A-9 | Ground 2 + Ground 1 | ground | single_source | |
| OEM-X2-79 | Coil low reference (even bank) | ground | SHADOW8-A-34 + SHADOW8-A-9 | Ground 2 + Ground 1 | ground | single_source | |
| OEM-X2-8 | EVAP canister purge solenoid | low_side_out | — | — | — | corroborated | |
| OEM-X2-9 | Cylinder shutoff solenoid 3 (AFM) | low_side_out | — | — | — | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-X1-19 | SP-14V-1 | 0.85 | no route | Ignition 1 voltage (key hot) | — | |
| W2 | OEM-X1-47 | SP-14V-1 | 0.85 | no route | Ignition 1 voltage (key hot) | — | |
| W3 | SP-14V-1 | SHADOW8-A-1 | 0.85 | no route | ECU supply | — | |
| W4 | SP-14V-1 | SHADOW8-B-26 | 0.85 | no route | Aux 9–12 power supply | — | |
| W5 | OEM-X1-20 | SHADOW8-B-1 | 0.85 | no route | Battery positive voltage (batt hot) | — | |
| W6 | OEM-X1-73 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W7 | OEM-X2-78 | SP-GND-1 | 0.85 | no route | Coil low reference (odd bank) | — | |
| W8 | OEM-X2-79 | SP-GND-1 | 0.85 | no route | Coil low reference (even bank) | — | |
| W9 | SP-GND-1 | SHADOW8-A-34 | 0.85 | no route | Ground 2 | — | |
| W10 | SP-GND-1 | SHADOW8-A-9 | 0.85 | no route | Ground 1 | — | |
| W11 | OEM-X1-11 | SP-0V-1 | 0.5 | no route | HO2S low reference, bank 1 sensor 2 | — | |
| W12 | OEM-X1-23 | SP-0V-1 | 0.5 | no route | APP sensor low reference | — | |
| W13 | OEM-X1-30 | SP-0V-1 | 0.5 | no route | APP sensor low reference | — | |
| W14 | OEM-X1-38 | SP-0V-1 | 0.5 | no route | Intake air temperature (IAT) low reference | — | |
| W15 | OEM-X1-49 | SP-0V-1 | 0.5 | no route | HO2S low reference, bank 2 sensor 2 | — | |
| W16 | OEM-X2-22 | SP-0V-1 | 0.5 | no route | ECT low reference | — | |
| W17 | OEM-X2-34 | SP-0V-1 | 0.5 | no route | Oil pressure low reference | — | |
| W18 | OEM-X2-35 | SP-0V-1 | 0.5 | no route | Throttle body low reference | — | |
| W19 | OEM-X2-52 | SP-0V-1 | 0.5 | no route | Camshaft actuator low reference | — | |
| W20 | OEM-X2-53 | SP-0V-1 | 0.5 | no route | MAP low reference | — | |
| W21 | OEM-X2-56 | SP-0V-1 | 0.5 | no route | HO2S low reference, bank 1 sensor 1 | — | |
| W22 | OEM-X2-60 | SP-0V-1 | 0.5 | no route | HO2S low reference, bank 2 sensor 1 | — | |
| W23 | OEM-X2-66 | SP-0V-1 | 0.5 | no route | Camshaft position low reference | — | |
| W24 | OEM-X2-69 | SP-0V-1 | 0.5 | no route | Crankshaft position low reference | — | |
| W25 | SP-0V-1 | SHADOW8-A-4 | 0.5 | no route | 0V analog reference | — | |
| W26 | SP-0V-1 | SHADOW8-A-7 | 0.5 | no route | Trigger ground | — | |
| W27 | OEM-X1-33 | SP-5V1-1 | 0.5 | no route | 5V reference (fuel tank pressure) | — | |
| W28 | OEM-X1-34 | SP-5V1-1 | 0.5 | no route | 5V reference (A/C pressure) | — | |
| W29 | OEM-X1-36 | SP-5V1-1 | 0.5 | no route | 5V reference (APP sensor) | — | |
| W30 | OEM-X1-56 | SP-5V1-1 | 0.5 | no route | 5V reference (APP sensor) | — | |
| W31 | OEM-X2-2 | SP-5V1-1 | 0.5 | no route | 5V reference (crankshaft sensor) | — | |
| W32 | OEM-X2-3 | SP-5V1-1 | 0.5 | no route | 5V reference (throttle body) | — | |
| W33 | OEM-X2-41 | SP-5V1-1 | 0.5 | no route | 5V reference (oil pressure) | — | |
| W34 | OEM-X2-43 | SP-5V1-1 | 0.5 | no route | 5V reference (MAP) | — | |
| W35 | OEM-X2-44 | SP-5V1-1 | 0.5 | no route | 5V reference (camshaft sensor) | — | |
| W36 | SP-5V1-1 | SHADOW8-A-3 | 0.5 | no route | 5.0V sensor supply | — | |
| W37 | OEM-X2-68 | SHADOW8-A-5 | 0.5 | no route | Crankshaft position signal (58x) | — | |
| W38 | OEM-X2-64 | SHADOW8-A-6 | 0.5 | no route | Camshaft position signal (4x) | — | |
| W39 | OEM-X2-26 | SHADOW8-A-16 | 0.5 | no route | Knock sensor 1 signal A | — | |
| W40 | OEM-X2-27 | SHADOW8-A-24 | 0.5 | no route | Knock sensor 1 signal B | — | |
| W41 | OEM-X2-70 | SHADOW8-B-27 | 0.5 | no route | Ignition coil 1 control | — | |
| W42 | OEM-X2-73 | SHADOW8-B-28 | 0.5 | no route | Ignition coil 2 control | — | |
| W43 | OEM-X2-77 | SHADOW8-B-29 | 0.5 | no route | Ignition coil 3 control | — | |
| W44 | OEM-X2-76 | SHADOW8-B-30 | 0.5 | no route | Ignition coil 4 control | — | |
| W45 | OEM-X2-75 | SHADOW8-B-31 | 0.5 | no route | Ignition coil 5 control | — | |
| W46 | OEM-X2-74 | SHADOW8-B-32 | 0.5 | no route | Ignition coil 6 control | — | |
| W47 | OEM-X2-72 | SHADOW8-B-33 | 0.5 | no route | Ignition coil 7 control | — | |
| W48 | OEM-X2-71 | SHADOW8-B-34 | 0.5 | no route | Ignition coil 8 control | — | |
| W49 | OEM-X2-20 | SHADOW8-B-2 | 0.5 | no route | Injector 1 | — | |
| W50 | OEM-X2-37 | SHADOW8-B-3 | 0.5 | no route | Injector 2 | — | |
| W51 | OEM-X2-38 | SHADOW8-B-4 | 0.5 | no route | Injector 3 | — | |
| W52 | OEM-X2-39 | SHADOW8-B-5 | 0.5 | no route | Injector 4 | — | |
| W53 | OEM-X2-18 | SHADOW8-B-6 | 0.5 | no route | Injector 5 | — | |
| W54 | OEM-X2-19 | SHADOW8-B-7 | 0.5 | no route | Injector 6 | — | |
| W55 | OEM-X2-40 | SHADOW8-B-8 | 0.5 | no route | Injector 7 | — | |
| W56 | OEM-X2-17 | SHADOW8-B-9 | 0.5 | no route | Injector 8 | — | |
| W57 | OEM-X2-6 | SHADOW8-B-22 | 0.5 | no route | Throttle actuator motor control 1 | — | |
| W58 | OEM-X2-5 | SHADOW8-B-23 | 0.5 | no route | Throttle actuator motor control 2 | — | |
| W59 | OEM-X1-50 | SHADOW8-B-10 | 0.5 | no route | Fuel pump relay control (primary) | — | |
| W60 | OEM-X1-59 | SHADOW8-B-11 | 0.5 | no route | Powertrain relay coil control (main relay) | — | |
| W61 | OEM-X1-17 | SHADOW8-B-12 | 0.5 | no route | High speed cooling fan relay | — | |
| W62 | OEM-X1-51 | SHADOW8-B-13 | 0.5 | no route | Fuel pump relay control (secondary) | — | |
| W63 | OEM-X1-52 | SHADOW8-B-14 | 0.5 | no route | Starter enable relay control | — | |
| W64 | OEM-X1-58 | SHADOW8-B-15 | 0.5 | no route | Low speed cooling fan relay | — | |
| W65 | OEM-X1-63 | SHADOW8-B-16 | 0.5 | no route | A/C compressor clutch relay | — | |
| W66 | OEM-X1-64 | SHADOW8-B-17 | 0.5 | no route | HO2S heater low control, bank 2 sensor 2 | — | |
| W67 | OEM-X1-65 | SHADOW8-B-24 | 0.5 | no route | HO2S heater low control, bank 1 sensor 2 | — | |
| W68 | OEM-X2-12 | SHADOW8-B-25 | 0.5 | no route | HO2S heater low control, bank 1 sensor 1 | — | |
| W69 | OEM-X1-41 | SHADOW8-A-10 | 0.5 | no route | Mass air flow (MAF) signal | — | |
| W70 | OEM-X2-58 | SHADOW8-A-11 | 0.5 | no route | Manifold absolute pressure (MAP) signal | — | |
| W71 | OEM-X1-29 | SHADOW8-A-12 | 0.5 | no route | Accelerator pedal position (APP) sensor 1 signal | — | |
| W72 | OEM-X2-65 | SHADOW8-A-13 | 0.5 | no route | Throttle position sensor 1 signal | — | |
| W73 | OEM-X1-32 | SHADOW8-A-14 | 0.5 | no route | Accelerator pedal position (APP) sensor 2 signal | — | |
| W74 | OEM-X2-63 | SHADOW8-A-18 | 0.5 | no route | Throttle position sensor 2 signal | — | |
| W75 | OEM-X1-10 | SHADOW8-A-19 | 0.5 | no route | HO2S signal, bank 1 sensor 2 (post-cat) | — | |
| W76 | OEM-X1-69 | SHADOW8-A-20 | 0.5 | no route | HO2S signal, bank 2 sensor 2 (post-cat) | — | |
| W77 | OEM-X2-57 | SHADOW8-A-21 | 0.5 | no route | HO2S signal, bank 1 sensor 1 (pre-cat) | — | |
| W78 | OEM-X2-59 | SHADOW8-A-22 | 0.5 | no route | HO2S signal, bank 2 sensor 1 (pre-cat) | — | |
| W79 | OEM-X1-71 | SHADOW8-A-26 | 0.5 | no route | VSS high signal (manual trans) | — | |
| W80 | OEM-X1-72 | SHADOW8-A-27 | 0.5 | no route | VSS low signal (manual trans) | — | |
| W81 | OEM-X1-9 | SHADOW8-A-28 | 0.5 | no route | Brake switch signal | — | |
| W82 | OEM-X2-33 | SHADOW8-A-29 | 0.5 | no route | Oil level switch signal | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 4-1437290-0 | TE | Superseal 1.0 34-way plug, Key 1 | 1.000 | ea |
| connector | 4-1437290-1 | TE | Superseal 1.0 34-way plug, Key 2 | 1.000 | ea |
| terminal | 3-1447221-4 | TE | Superseal 1.0 socket terminal, 20 AWG (0.5 sq mm) | 54.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (12)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | PHYS_REQUIRED_OPEN | SHADOW8-B-21 | SHADOW8-B-21 "Digital input 10 / ignition switch" is required but not wired. |
| error | REQUIRED_UNMAPPED | OEM-X2-21 | Required OEM function "Engine coolant temperature (ECT) signal" (temp_in) is not connected to the new ECU. |
| warn | DBW_MOTOR_CURRENT | SHADOW8-B-22 | Cannot confirm Shadow 8 can drive the throttle motor: SHADOW8-B-22 "Aux output 9" is rated 5.0 A, but the motor current at OEM-X2-6 is unknown. Add the motor's peak current from a source, or measure the motor resistance: peak ≈ 14 V ÷ R (Hondata measured 4.9 A for a Civic Si body, 10.4 A for a ZDX body; holding current is about 1 A). |
| warn | DBW_MOTOR_CURRENT | SHADOW8-B-23 | Cannot confirm Shadow 8 can drive the throttle motor: SHADOW8-B-23 "Aux output 10" is rated 5.0 A, but the motor current at OEM-X2-5 is unknown. Add the motor's peak current from a source, or measure the motor resistance: peak ≈ 14 V ÷ R (Hondata measured 4.9 A for a Civic Si body, 10.4 A for a ZDX body; holding current is about 1 A). |
| warn | DBW_MOTOR_ISOLATION | SHADOW8-B-26 | SHADOW8-B-26 "Aux 9–12 power supply" is fed from the same net as the ECU main supply (SHADOW8-A-1). Link's S2000 DBW wiring feeds the throttle-motor supply through a separate isolation relay switched by the ECU, so motor power can be cut on a throttle fault. Add one, or confirm Shadow 8 cuts the H-bridge internally. |
| warn | NET_FAMILY | OEM-X1-65 ↔ SHADOW8-B-24 | OEM-X1-65 "HO2S heater low control, bank 1 sensor 2" [low_side_out] is wired to SHADOW8-B-24 "Aux output 11" [hbridge_out]. A half-bridge can act as a low-side switch only if configured that way. |
| warn | NET_FAMILY | OEM-X2-12 ↔ SHADOW8-B-25 | OEM-X2-12 "HO2S heater low control, bank 1 sensor 1" [low_side_out] is wired to SHADOW8-B-25 "Aux output 12" [hbridge_out]. A half-bridge can act as a low-side switch only if configured that way. |
| info | NET_FAMILY | OEM-X1-52 ↔ SHADOW8-B-14 | OEM-X1-52 "Starter enable relay control" [low_side_out] is wired to SHADOW8-B-14 "Aux output 5" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-X1-58 ↔ SHADOW8-B-15 | OEM-X1-58 "Low speed cooling fan relay" [low_side_out] is wired to SHADOW8-B-15 "Aux output 6" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-X1-63 ↔ SHADOW8-B-16 | OEM-X1-63 "A/C compressor clutch relay" [low_side_out] is wired to SHADOW8-B-16 "Aux output 7" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-X1-64 ↔ SHADOW8-B-17 | OEM-X1-64 "HO2S heater low control, bank 2 sensor 2" [low_side_out] is wired to SHADOW8-B-17 "Aux output 8" [switch_out]. Configure this output as low side. |
| info | UNMAPPED | OEM | 19 optional OEM pins are not mapped: OEM-X1-12 A/C refrigerant pressure signal; OEM-X1-24 Fuel tank pressure signal; OEM-X1-37 Intake air temperature (IAT) signal; OEM-X1-48 Tachometer output; OEM-X1-57 VSS output to ABS (128k); OEM-X1-61 EVAP canister vent solenoid; OEM-X1-68 Malfunction indicator lamp (MIL); OEM-X2-10 Cylinder shutoff solenoid 1 (AFM); OEM-X2-11 Cylinder shutoff solenoid 4 (AFM); OEM-X2-13 HO2S heater low control, bank 2 sensor 1; OEM-X2-14 Cylinder shutoff solenoid 2 (AFM); OEM-X2-16 Camshaft actuator solenoid (VVT); OEM-X2-29 Knock sensor 2 signal A; OEM-X2-30 Knock sensor 2 signal B; OEM-X2-32 Generator field duty control; OEM-X2-50 Engine oil pressure signal; OEM-X2-61 Charge indicator signal; OEM-X2-8 EVAP canister purge solenoid; OEM-X2-9 Cylinder shutoff solenoid 3 (AFM) |
Accepted (0)
| Code | Subject | Reason | By |
|---|
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-06. Review every wire against both manuals before building. Open items: - OEM-X2 21: Engine coolant temperature (ECT) signal: no free thermistor/analog_0_5 on Emtron Shadow 8 - SHADOW8-B 21: Digital input 10 / ignition switch: required by Emtron Shadow 8 but no stock pin feeds it; wire by hand Not wired: - SHADOW8-A 17: Knock 1 − left open: the stock knock sensor has one ECU wire; check the ECU manual for single-wire knock sensors - SHADOW8-A 25: Knock 2 − left open: the stock knock sensor has one ECU wire; check the ECU manual for single-wire knock sensors - OEM-X2 29: Knock sensor 2 signal A: no free knock input on Emtron Shadow 8 - OEM-X2 30: Knock sensor 2 signal B: no free knock input on Emtron Shadow 8 - OEM-X2 13: HO2S heater low control, bank 2 sensor 1: no free heater_low_side/low_side/ls_hs/hbridge on Emtron Shadow 8 - OEM-X2 10: Cylinder shutoff solenoid 1 (AFM): no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X2 14: Cylinder shutoff solenoid 2 (AFM): no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X2 9: Cylinder shutoff solenoid 3 (AFM): no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X2 11: Cylinder shutoff solenoid 4 (AFM): no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X1 61: EVAP canister vent solenoid: no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X1 68: Malfunction indicator lamp (MIL): no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X2 16: Camshaft actuator solenoid (VVT): no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X2 32: Generator field duty control: no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X2 61: Charge indicator signal: no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X2 8: EVAP canister purge solenoid: no free low_side/ls_hs/injector/hbridge on Emtron Shadow 8 - OEM-X1 48: Tachometer output: no free tacho/frequency_out/low_side/ls_hs on Emtron Shadow 8 - OEM-X1 57: VSS output to ABS (128k): no free frequency_out/tacho/low_side/ls_hs on Emtron Shadow 8 - OEM-X1 37: Intake air temperature (IAT) signal: no free thermistor/analog_0_5 on Emtron Shadow 8 - OEM-X1 12: A/C refrigerant pressure signal: no free analog_0_5 on Emtron Shadow 8 - OEM-X1 24: Fuel tank pressure signal: no free analog_0_5 on Emtron Shadow 8 - OEM-X2 50: Engine oil pressure signal: no free analog_0_5 on Emtron Shadow 8
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | Emtron Shadow 8 ECU datasheet | https://docs.emtronaustralia.com.au/engine-management/datasheets/shadow-8-datasheet/index.html | archive | 2026-10-05 | f004c9a8d60c |
| 4 | vendor_doc | Emtron Shadow 8 pinout | https://docs.emtronaustralia.com.au/engine-management/wiring/shadow-8/shadow-8-pinout/index.html | archive | 2026-10-05 | f510053951c7 |
| 4 | vendor_doc | MaxxECU webhelp: Wiring — plug-in ECU Chevrolet Corvette C6 (GM E38 ECM) | http://www.maxxecu.com/webhelp/wirings-pluginecu-chevrolet_corvette_c6_e38_ecm.html | — | — | — |
| 2 | community_copy | lt1swap.com: E38 ECM Connector Pinouts | https://lt1swap.com/E38 ECM Connector Pinouts.htm | — | — | — |