Chevrolet Camaro SS 2010-15 (LS3/L99) → MoTeC M190 13190 (auto)

Chevrolet Camaro SS 2010-15 (LS3/L99) — MoTeC — M190

Drawn by Michael Gnankou · Rev 0 · proposal · 2026-10-08

Before you start

Status	proposal · not yet verified: nobody has reported building and running this harness
Open errors	none
Size of the job	111 wires · 9 connectors · 0 part lines
Tools	Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink
Order of work	1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up.

Build checklist

Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.

Wire	From	To	Gauge	Cut	Label	Crimp A	Crimp B	Pin A	Pin B	Continuity
W1	OEM-X1-19	SP-14V-1	0.85	☐	☐	☐	☐	☐	☐	☐
W2	OEM-X1-47	SP-14V-1	0.85	☐	☐	☐	☐	☐	☐	☐
W3	SP-14V-1	M190-B-H	0.85	☐	☐	☐	☐	☐	☐	☐
W4	SP-14V-1	M190-B-J	0.85	☐	☐	☐	☐	☐	☐	☐
W5	SP-14V-1	M190-B-K	0.85	☐	☐	☐	☐	☐	☐	☐
W6	SP-14V-1	M190-B-L	0.85	☐	☐	☐	☐	☐	☐	☐
W7	OEM-X1-20	M190-A-38	0.85	☐	☐	☐	☐	☐	☐	☐
W8	OEM-X1-73	SP-GND-1	0.85	☐	☐	☐	☐	☐	☐	☐
W9	OEM-X2-78	SP-GND-1	0.85	☐	☐	☐	☐	☐	☐	☐
W10	OEM-X2-79	SP-GND-1	0.85	☐	☐	☐	☐	☐	☐	☐
W11	SP-GND-1	M190-B-G	0.85	☐	☐	☐	☐	☐	☐	☐
W12	SP-GND-1	M190-B-W	0.85	☐	☐	☐	☐	☐	☐	☐
W13	SP-GND-1	M190-B-X	0.85	☐	☐	☐	☐	☐	☐	☐
W14	SP-GND-1	M190-B-Y	0.85	☐	☐	☐	☐	☐	☐	☐
W15	SP-GND-1	M190-B-Z	0.85	☐	☐	☐	☐	☐	☐	☐
W16	SP-GND-1	M190-B-c	0.85	☐	☐	☐	☐	☐	☐	☐
W17	OEM-X1-11	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W18	OEM-X1-23	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W19	OEM-X1-30	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W20	OEM-X1-38	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W21	OEM-X1-49	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W22	OEM-X2-22	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W23	OEM-X2-34	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W24	OEM-X2-35	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W25	OEM-X2-52	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W26	OEM-X2-53	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W27	OEM-X2-56	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W28	OEM-X2-60	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W29	OEM-X2-66	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W30	OEM-X2-69	SP-0V-1	0.5	☐	☐	☐	☐	☐	☐	☐
W31	SP-0V-1	M190-A-18	0.5	☐	☐	☐	☐	☐	☐	☐
W32	SP-0V-1	M190-A-19	0.5	☐	☐	☐	☐	☐	☐	☐
W33	SP-0V-1	M190-A-20	0.5	☐	☐	☐	☐	☐	☐	☐
W34	SP-0V-1	M190-C-14	0.5	☐	☐	☐	☐	☐	☐	☐
W35	SP-0V-1	M190-C-15	0.5	☐	☐	☐	☐	☐	☐	☐
W36	SP-0V-1	M190-C-23	0.5	☐	☐	☐	☐	☐	☐	☐
W37	SP-0V-1	M190-C-30	0.5	☐	☐	☐	☐	☐	☐	☐
W38	OEM-X1-33	SP-5V1-1	0.5	☐	☐	☐	☐	☐	☐	☐
W39	OEM-X1-34	SP-5V1-1	0.5	☐	☐	☐	☐	☐	☐	☐
W40	OEM-X1-36	SP-5V1-1	0.5	☐	☐	☐	☐	☐	☐	☐
W41	OEM-X1-56	SP-5V1-1	0.5	☐	☐	☐	☐	☐	☐	☐
W42	OEM-X2-2	SP-5V1-1	0.5	☐	☐	☐	☐	☐	☐	☐
W43	OEM-X2-3	SP-5V1-1	0.5	☐	☐	☐	☐	☐	☐	☐
W44	OEM-X2-41	SP-5V1-1	0.5	☐	☐	☐	☐	☐	☐	☐
W45	OEM-X2-43	SP-5V1-1	0.5	☐	☐	☐	☐	☐	☐	☐
W46	OEM-X2-44	SP-5V1-1	0.5	☐	☐	☐	☐	☐	☐	☐
W47	SP-5V1-1	M190-A-16	0.5	☐	☐	☐	☐	☐	☐	☐
W48	OEM-X2-68	M190-C-18	0.5	☐	☐	☐	☐	☐	☐	☐
W49	OEM-X2-64	M190-C-32	0.5	☐	☐	☐	☐	☐	☐	☐
W50	OEM-X2-26	M190-C-51	0.5	☐	☐	☐	☐	☐	☐	☐
W51	OEM-X2-27	M190-C-44	0.5	☐	☐	☐	☐	☐	☐	☐
W52	OEM-X2-29	M190-C-43	0.5	☐	☐	☐	☐	☐	☐	☐
W53	OEM-X2-30	M190-C-49	0.5	☐	☐	☐	☐	☐	☐	☐
W54	OEM-X2-70	M190-C-16	0.5	☐	☐	☐	☐	☐	☐	☐
W55	OEM-X2-73	M190-C-8	0.5	☐	☐	☐	☐	☐	☐	☐
W56	OEM-X2-77	M190-C-2	0.5	☐	☐	☐	☐	☐	☐	☐
W57	OEM-X2-76	M190-C-1	0.5	☐	☐	☐	☐	☐	☐	☐
W58	OEM-X2-75	M190-C-5	0.5	☐	☐	☐	☐	☐	☐	☐
W59	OEM-X2-74	M190-C-4	0.5	☐	☐	☐	☐	☐	☐	☐
W60	OEM-X2-72	M190-C-9	0.5	☐	☐	☐	☐	☐	☐	☐
W61	OEM-X2-71	M190-C-3	0.5	☐	☐	☐	☐	☐	☐	☐
W62	OEM-X2-20	M190-A-11	0.5	☐	☐	☐	☐	☐	☐	☐
W63	OEM-X2-37	M190-A-3	0.5	☐	☐	☐	☐	☐	☐	☐
W64	OEM-X2-38	M190-B-U	0.5	☐	☐	☐	☐	☐	☐	☐
W65	OEM-X2-39	M190-A-12	0.5	☐	☐	☐	☐	☐	☐	☐
W66	OEM-X2-18	M190-A-2	0.5	☐	☐	☐	☐	☐	☐	☐
W67	OEM-X2-19	M190-B-V	0.5	☐	☐	☐	☐	☐	☐	☐
W68	OEM-X2-40	M190-A-1	0.5	☐	☐	☐	☐	☐	☐	☐
W69	OEM-X2-17	M190-A-26	0.5	☐	☐	☐	☐	☐	☐	☐
W70	OEM-X2-6	M190-B-A	0.5	☐	☐	☐	☐	☐	☐	☐
W71	OEM-X2-5	M190-B-B	0.5	☐	☐	☐	☐	☐	☐	☐
W72	OEM-X1-50	M190-B-b	0.5	☐	☐	☐	☐	☐	☐	☐
W73	OEM-X1-59	M190-A-5	0.5	☐	☐	☐	☐	☐	☐	☐
W74	OEM-X1-17	M190-B-S	0.5	☐	☐	☐	☐	☐	☐	☐
W75	OEM-X1-51	M190-A-48	0.5	☐	☐	☐	☐	☐	☐	☐
W76	OEM-X1-52	M190-B-a	0.5	☐	☐	☐	☐	☐	☐	☐
W77	OEM-X1-58	M190-A-40	0.5	☐	☐	☐	☐	☐	☐	☐
W78	OEM-X1-63	M190-B-T	0.5	☐	☐	☐	☐	☐	☐	☐
W79	OEM-X1-64	M190-B-C	0.5	☐	☐	☐	☐	☐	☐	☐
W80	OEM-X1-65	M190-B-D	0.5	☐	☐	☐	☐	☐	☐	☐
W81	OEM-X2-12	M190-B-E	0.5	☐	☐	☐	☐	☐	☐	☐
W82	OEM-X2-13	M190-B-F	0.5	☐	☐	☐	☐	☐	☐	☐
W83	OEM-X2-10	M190-A-25	0.5	☐	☐	☐	☐	☐	☐	☐
W84	OEM-X2-14	M190-A-10	0.5	☐	☐	☐	☐	☐	☐	☐
W85	OEM-X2-9	M190-A-47	0.5	☐	☐	☐	☐	☐	☐	☐
W86	OEM-X2-11	M190-A-32	0.5	☐	☐	☐	☐	☐	☐	☐
W87	OEM-X1-61	M190-A-17	0.5	☐	☐	☐	☐	☐	☐	☐
W88	OEM-X1-68	M190-A-4	0.5	☐	☐	☐	☐	☐	☐	☐
W89	OEM-X2-16	M190-A-33	0.5	☐	☐	☐	☐	☐	☐	☐
W90	OEM-X2-32	M190-A-45	0.5	☐	☐	☐	☐	☐	☐	☐
W91	OEM-X2-61	M190-A-44	0.5	☐	☐	☐	☐	☐	☐	☐
W92	OEM-X2-8	M190-A-36	0.5	☐	☐	☐	☐	☐	☐	☐
W93	OEM-X1-41	M190-C-42	0.5	☐	☐	☐	☐	☐	☐	☐
W94	OEM-X2-58	M190-C-36	0.5	☐	☐	☐	☐	☐	☐	☐
W95	OEM-X1-29	M190-C-35	0.5	☐	☐	☐	☐	☐	☐	☐
W96	OEM-X2-65	M190-C-28	0.5	☐	☐	☐	☐	☐	☐	☐
W97	OEM-X1-32	M190-C-29	0.5	☐	☐	☐	☐	☐	☐	☐
W98	OEM-X2-63	M190-C-11	0.5	☐	☐	☐	☐	☐	☐	☐
W99	OEM-X1-10	M190-A-7	0.5	☐	☐	☐	☐	☐	☐	☐
W100	OEM-X1-69	M190-A-6	0.5	☐	☐	☐	☐	☐	☐	☐
W101	OEM-X2-57	M190-C-12	0.5	☐	☐	☐	☐	☐	☐	☐
W102	OEM-X2-59	M190-C-6	0.5	☐	☐	☐	☐	☐	☐	☐
W103	OEM-X2-21	M190-C-37	0.5	☐	☐	☐	☐	☐	☐	☐
W104	OEM-X1-37	M190-C-39	0.5	☐	☐	☐	☐	☐	☐	☐
W105	OEM-X1-12	M190-C-13	0.5	☐	☐	☐	☐	☐	☐	☐
W106	OEM-X1-24	M190-C-7	0.5	☐	☐	☐	☐	☐	☐	☐
W107	OEM-X2-50	M190-A-13	0.5	☐	☐	☐	☐	☐	☐	☐
W108	OEM-X1-71	M190-C-25	0.5	☐	☐	☐	☐	☐	☐	☐
W109	OEM-X1-72	M190-C-27	0.5	☐	☐	☐	☐	☐	☐	☐
W110	OEM-X1-9	M190-A-21	0.5	☐	☐	☐	☐	☐	☐	☐
W111	OEM-X2-33	M190-A-14	0.5	☐	☐	☐	☐	☐	☐	☐

Bench test (before first power-up)

Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).

#	Probe A	Probe B	Expect	Why
1	M190-A-16	M190-B-G	open (OL)	5 V sensor reference must not touch power ground
2	M190-A-38	M190-B-G	open (OL)	+12 V supply must not touch power ground
3	M190-B-H	M190-B-G	open (OL)	+12 V supply must not touch power ground
4	M190-A-18	M190-A-16	open (OL)	sensor ground must not touch 5 V sensor reference
5	M190-A-18	M190-A-38	open (OL)	sensor ground must not touch +12 V supply
6	M190-A-18	M190-B-H	open (OL)	sensor ground must not touch +12 V supply
7	M190-A-38	M190-A-16	open (OL)	+12 V supply must not touch 5 V sensor reference
8	M190-B-H	M190-A-16	open (OL)	+12 V supply must not touch 5 V sensor reference

Revisions

Rev	Label	By	Date
No revisions yet.

Schematic

Connectors

M190-A

Cavity	Function	Signal	Wire	Colour	Gauge (mm²)	Destination	Terminal	Seal	Plug
1	Low Side Injector 3	—	W68	—	0.5	OEM-X2-40	—	—	—
10	Low Side Injector 8	—	W84	—	0.5	OEM-X2-14	—	—	—
11	Peak Hold Injector 1	—	W62	—	0.5	OEM-X2-20	—	—	—
12	Peak Hold Injector 2	—	W65	—	0.5	OEM-X2-39	—	—	—
13	Analogue Voltage Input 11	—	W107	—	0.5	OEM-X2-50	—	—	—
14	Digital Input 2	—	W111	—	0.5	OEM-X2-33	—	—	—
15	RS232 Receive	—	—	—	—	—	—	—	—
16	Sensor 5.0V C3	—	W47	—	0.5	SP-5V1-1	—	—	—
17	Low Side Injector 11	—	W87	—	0.5	OEM-X1-61	—	—	—
18	Sensor 0V C1	—	W31	—	0.5	SP-0V-1	—	—	—
19	Sensor 0V C2	—	W32	—	0.5	SP-0V-1	—	—	—
2	Low Side Injector 2	—	W66	—	0.5	OEM-X2-18	—	—	—
20	Sensor 0V C3	—	W33	—	0.5	SP-0V-1	—	—	—
21	Digital Input 1	—	W110	—	0.5	OEM-X1-9	—	—	—
22	LIN Bus	—	—	—	—	—	—	—	—
23	RS232 Transmit	—	—	—	—	—	—	—	—
24	CAN Bus 2 High	—	—	—	—	—	—	—	—
25	Low Side Injector 7	—	W83	—	0.5	OEM-X2-10	—	—	—
26	Peak Hold Injector 3	—	W69	—	0.5	OEM-X2-17	—	—	—
27	Analogue Voltage Input 15	—	—	—	—	—	—	—	—
28	Analogue Voltage Input 16	—	—	—	—	—	—	—	—
29	Analogue Voltage Input 17	—	—	—	—	—	—	—	—
3	Low Side Injector 1	—	W63	—	0.5	OEM-X2-37	—	—	—
30	Digital Input 3	—	—	—	—	—	—	—	—
31	CAN Bus 2 Low	—	—	—	—	—	—	—	—
32	Low Side Injector 10	—	W86	—	0.5	OEM-X2-11	—	—	—
33	Peak Hold Injector 4	—	W89	—	0.5	OEM-X2-16	—	—	—
34	Analogue Voltage Input 13	—	—	—	—	—	—	—	—
35	Analogue Voltage Input 12	—	—	—	—	—	—	—	—
36	Peak Hold Injector 7	—	W92	—	0.5	OEM-X2-8	—	—	—
37	Digital Input 4	—	—	—	—	—	—	—	—
38	Battery Backup	—	W7	—	0.85	OEM-X1-20	—	—	—
39	CAN Bus 3 High	—	—	—	—	—	—	—	—
4	Low Side Injector 12	—	W88	—	0.5	OEM-X1-68	—	—	—
40	Low Side Injector 6	—	W77	—	0.5	OEM-X1-58	—	—	—
41	Analogue Voltage Input 14	—	—	—	—	—	—	—	—
42	Peak Hold Injector 9	—	—	—	—	—	—	—	—
43	Peak Hold Injector 10	—	—	—	—	—	—	—	—
44	Peak Hold Injector 6	—	W91	—	0.5	OEM-X2-61	—	—	—
45	Peak Hold Injector 5	—	W90	—	0.5	OEM-X2-32	—	—	—
46	CAN Bus 3 Low	—	—	—	—	—	—	—	—
47	Low Side Injector 9	—	W85	—	0.5	OEM-X2-9	—	—	—
48	Low Side Injector 5	—	W75	—	0.5	OEM-X1-51	—	—	—
49	Peak Hold Injector 11	—	—	—	—	—	—	—	—
5	Low Side Injector 4	—	W73	—	0.5	OEM-X1-59	—	—	—
50	Peak Hold Injector 12	—	—	—	—	—	—	—	—
51	Peak Hold Injector 8	—	—	—	—	—	—	—	—
52	Low Side Ignition 12	—	—	—	—	—	—	—	—
53	Low Side Ignition 9	—	—	—	—	—	—	—	—
54	Low Side Ignition 10	—	—	—	—	—	—	—	—
55	Low Side Ignition 11	—	—	—	—	—	—	—	—
6	Lambda Narrow Input 2	—	W100	—	0.5	OEM-X1-69	—	—	—
7	Lambda Narrow Input 1	—	W99	—	0.5	OEM-X1-10	—	—	—
8	Sensor 5.0V C1	—	—	—	—	—	—	—	—
9	Sensor 5.0V C2	—	—	—	—	—	—	—	—

M190-B

Cavity	Function	Signal	Wire	Colour	Gauge (mm²)	Destination	Terminal	Seal	Plug
A	Half Bridge Output 1	—	W70	—	0.5	OEM-X2-6	—	—	—
B	Half Bridge Output 2	—	W71	—	0.5	OEM-X2-5	—	—	—
C	Half Bridge Output 3	—	W79	—	0.5	OEM-X1-64	—	—	—
D	Half Bridge Output 4	—	W80	—	0.5	OEM-X1-65	—	—	—
E	Half Bridge Output 5	—	W81	—	0.5	OEM-X2-12	—	—	—
F	Half Bridge Output 6	—	W82	—	0.5	OEM-X2-13	—	—	—
G	Battery Negative 1	—	W11	—	0.85	SP-GND-1	—	—	—
H	Battery Positive 1	—	W3	—	0.85	SP-14V-1	—	—	—
J	Battery Positive 2	—	W4	—	0.85	SP-14V-1	—	—	—
K	Battery Positive 3	—	W5	—	0.85	SP-14V-1	—	—	—
L	Battery Positive 4	—	W6	—	0.85	SP-14V-1	—	—	—
M	Half Bridge Output 10	—	—	—	—	—	—	—	—
N	Half Bridge Output 9	—	—	—	—	—	—	—	—
P	Half Bridge Output 8	—	—	—	—	—	—	—	—
R	Half Bridge Output 7	—	—	—	—	—	—	—	—
S	Low Side Injector 4	—	W74	—	0.5	OEM-X1-17	—	—	—
T	Low Side Injector 6	—	W78	—	0.5	OEM-X1-63	—	—	—
U	Low Side Injector 1	—	W64	—	0.5	OEM-X2-38	—	—	—
V	Low Side Injector 2	—	W67	—	0.5	OEM-X2-19	—	—	—
W	Battery Negative 2	—	W12	—	0.85	SP-GND-1	—	—	—
X	Battery Negative 3	—	W13	—	0.85	SP-GND-1	—	—	—
Y	Battery Negative 4	—	W14	—	0.85	SP-GND-1	—	—	—
Z	Battery Negative 5	—	W15	—	0.85	SP-GND-1	—	—	—
a	Low Side Injector 5	—	W76	—	0.5	OEM-X1-52	—	—	—
b	Low Side Injector 3	—	W72	—	0.5	OEM-X1-50	—	—	—
c	Battery Negative 6	—	W16	—	0.85	SP-GND-1	—	—	—

M190-C

Cavity	Function	Signal	Wire	Colour	Gauge (mm²)	Destination	Terminal	Seal	Plug
1	Low Side Ignition 4	—	W57	—	0.5	OEM-X2-76	—	—	—
10	Universal Digital Input 8	—	—	—	—	—	—	—	—
11	Analogue Voltage Input 6	—	W98	—	0.5	OEM-X2-63	—	—	—
12	Analogue Voltage Input 7	—	W101	—	0.5	OEM-X2-57	—	—	—
13	Analogue Voltage Input 9	—	W105	—	0.5	OEM-X1-12	—	—	—
14	Sensor 0V A1	—	W34	—	0.5	SP-0V-1	—	—	—
15	Sensor 0V A2	—	W35	—	0.5	SP-0V-1	—	—	—
16	Low Side Ignition 1	—	W54	—	0.5	OEM-X2-70	—	—	—
17	Universal Digital Input 7	—	—	—	—	—	—	—	—
18	Universal Digital Input 1	—	W48	—	0.5	OEM-X2-68	—	—	—
19	Universal Digital Input 12	—	—	—	—	—	—	—	—
2	Low Side Ignition 3	—	W56	—	0.5	OEM-X2-77	—	—	—
20	Universal Digital Input 11	—	—	—	—	—	—	—	—
21	Universal Digital Input 10	—	—	—	—	—	—	—	—
22	Universal Digital Input 9	—	—	—	—	—	—	—	—
23	Sensor 0V B1	—	W36	—	0.5	SP-0V-1	—	—	—
24	CAN Bus 1 High	—	—	—	—	—	—	—	—
25	Universal Digital Input 3	—	W108	—	0.5	OEM-X1-71	—	—	—
26	Ethernet Receive -	—	—	—	—	—	—	—	—
27	Universal Digital Input 4	—	W109	—	0.5	OEM-X1-72	—	—	—
28	Analogue Voltage Input 4	—	W96	—	0.5	OEM-X2-65	—	—	—
29	Analogue Voltage Input 5	—	W97	—	0.5	OEM-X1-32	—	—	—
3	Low Side Ignition 8	—	W61	—	0.5	OEM-X2-71	—	—	—
30	Sensor 0V B2	—	W37	—	0.5	SP-0V-1	—	—	—
31	CAN Bus 1 Low	—	—	—	—	—	—	—	—
32	Universal Digital Input 2	—	W49	—	0.5	OEM-X2-64	—	—	—
33	Ethernet Receive +	—	—	—	—	—	—	—	—
34	Ethernet Transmit -	—	—	—	—	—	—	—	—
35	Analogue Voltage Input 3	—	W95	—	0.5	OEM-X1-29	—	—	—
36	Analogue Voltage Input 2	—	W94	—	0.5	OEM-X2-58	—	—	—
37	Analogue Temperature Input 1	—	W103	—	0.5	OEM-X2-21	—	—	—
38	Analogue Temperature Input 3	—	—	—	—	—	—	—	—
39	Analogue Temperature Input 2	—	W104	—	0.5	OEM-X1-37	—	—	—
4	Low Side Ignition 6	—	W59	—	0.5	OEM-X2-74	—	—	—
40	Universal Digital Input 5	—	—	—	—	—	—	—	—
41	Ethernet Transmit +	—	—	—	—	—	—	—	—
42	Analogue Voltage Input 1	—	W93	—	0.5	OEM-X1-41	—	—	—
43	Knock Input 3	—	W52	—	0.5	OEM-X2-29	—	—	—
44	Knock Input 2	—	W51	—	0.5	OEM-X2-27	—	—	—
45	Analogue Temperature Input 5	—	—	—	—	—	—	—	—
46	Analogue Temperature Input 4	—	—	—	—	—	—	—	—
47	Universal Digital Input 6	—	—	—	—	—	—	—	—
48	Sensor 5.0V A1	—	—	—	—	—	—	—	—
49	Knock Input 4	—	W53	—	0.5	OEM-X2-30	—	—	—
5	Low Side Ignition 5	—	W58	—	0.5	OEM-X2-75	—	—	—
50	Sensor 5.0V B1	—	—	—	—	—	—	—	—
51	Knock Input 1	—	W50	—	0.5	OEM-X2-26	—	—	—
52	Analogue Temperature Input 6	—	—	—	—	—	—	—	—
53	Sensor 5.0V A2	—	—	—	—	—	—	—	—
54	Sensor 6.3V	—	—	—	—	—	—	—	—
55	Sensor 5.0V B2	—	—	—	—	—	—	—	—
6	Analogue Voltage Input 8	—	W102	—	0.5	OEM-X2-59	—	—	—
7	Analogue Voltage Input 10	—	W106	—	0.5	OEM-X1-24	—	—	—
8	Low Side Ignition 2	—	W55	—	0.5	OEM-X2-73	—	—	—
9	Low Side Ignition 7	—	W60	—	0.5	OEM-X2-72	—	—	—

OEM-X1

Cavity	Function	Signal	Wire	Colour	Gauge (mm²)	Destination	Terminal	Seal	Plug
10	HO2S signal, bank 1 sensor 2 (post-cat)	—	W99	—	0.5	M190-A-7	—	—	—
11	HO2S low reference, bank 1 sensor 2	—	W17	—	0.5	SP-0V-1	—	—	—
12	A/C refrigerant pressure signal	—	W105	—	0.5	M190-C-13	—	—	—
17	High speed cooling fan relay	—	W74	—	0.5	M190-B-S	—	—	—
19	Ignition 1 voltage (key hot)	—	W1	—	0.85	SP-14V-1	—	—	—
20	Battery positive voltage (batt hot)	—	W7	—	0.85	M190-A-38	—	—	—
23	APP sensor low reference	—	W18	—	0.5	SP-0V-1	—	—	—
24	Fuel tank pressure signal	—	W106	—	0.5	M190-C-7	—	—	—
29	Accelerator pedal position (APP) sensor 1 signal	—	W95	—	0.5	M190-C-35	—	—	—
30	APP sensor low reference	—	W19	—	0.5	SP-0V-1	—	—	—
32	Accelerator pedal position (APP) sensor 2 signal	—	W97	—	0.5	M190-C-29	—	—	—
33	5V reference (fuel tank pressure)	—	W38	—	0.5	SP-5V1-1	—	—	—
34	5V reference (A/C pressure)	—	W39	—	0.5	SP-5V1-1	—	—	—
36	5V reference (APP sensor)	—	W40	—	0.5	SP-5V1-1	—	—	—
37	Intake air temperature (IAT) signal	—	W104	—	0.5	M190-C-39	—	—	—
38	Intake air temperature (IAT) low reference	—	W20	—	0.5	SP-0V-1	—	—	—
41	Mass air flow (MAF) signal	—	W93	—	0.5	M190-C-42	—	—	—
47	Ignition 1 voltage (key hot)	—	W2	—	0.85	SP-14V-1	—	—	—
48	Tachometer output	—	—	—	—	—	—	—	—
49	HO2S low reference, bank 2 sensor 2	—	W21	—	0.5	SP-0V-1	—	—	—
50	Fuel pump relay control (primary)	—	W72	—	0.5	M190-B-b	—	—	—
51	Fuel pump relay control (secondary)	—	W75	—	0.5	M190-A-48	—	—	—
52	Starter enable relay control	—	W76	—	0.5	M190-B-a	—	—	—
56	5V reference (APP sensor)	—	W41	—	0.5	SP-5V1-1	—	—	—
57	VSS output to ABS (128k)	—	—	—	—	—	—	—	—
58	Low speed cooling fan relay	—	W77	—	0.5	M190-A-40	—	—	—
59	Powertrain relay coil control (main relay)	—	W73	—	0.5	M190-A-5	—	—	—
61	EVAP canister vent solenoid	—	W87	—	0.5	M190-A-17	—	—	—
63	A/C compressor clutch relay	—	W78	—	0.5	M190-B-T	—	—	—
64	HO2S heater low control, bank 2 sensor 2	—	W79	—	0.5	M190-B-C	—	—	—
65	HO2S heater low control, bank 1 sensor 2	—	W80	—	0.5	M190-B-D	—	—	—
68	Malfunction indicator lamp (MIL)	—	W88	—	0.5	M190-A-4	—	—	—
69	HO2S signal, bank 2 sensor 2 (post-cat)	—	W100	—	0.5	M190-A-6	—	—	—
71	VSS high signal (manual trans)	—	W108	—	0.5	M190-C-25	—	—	—
72	VSS low signal (manual trans)	—	W109	—	0.5	M190-C-27	—	—	—
73	Power ground	—	W8	—	0.85	SP-GND-1	—	—	—
9	Brake switch signal	—	W110	—	0.5	M190-A-21	—	—	—

OEM-X2

Cavity	Function	Signal	Wire	Colour	Gauge (mm²)	Destination	Terminal	Seal	Plug
10	Cylinder shutoff solenoid 1 (AFM)	—	W83	—	0.5	M190-A-25	—	—	—
11	Cylinder shutoff solenoid 4 (AFM)	—	W86	—	0.5	M190-A-32	—	—	—
12	HO2S heater low control, bank 1 sensor 1	—	W81	—	0.5	M190-B-E	—	—	—
13	HO2S heater low control, bank 2 sensor 1	—	W82	—	0.5	M190-B-F	—	—	—
14	Cylinder shutoff solenoid 2 (AFM)	—	W84	—	0.5	M190-A-10	—	—	—
16	Camshaft actuator solenoid (VVT)	—	W89	—	0.5	M190-A-33	—	—	—
17	Injector 8	—	W69	—	0.5	M190-A-26	—	—	—
18	Injector 5	—	W66	—	0.5	M190-A-2	—	—	—
19	Injector 6	—	W67	—	0.5	M190-B-V	—	—	—
2	5V reference (crankshaft sensor)	—	W42	—	0.5	SP-5V1-1	—	—	—
20	Injector 1	—	W62	—	0.5	M190-A-11	—	—	—
21	Engine coolant temperature (ECT) signal	—	W103	—	0.5	M190-C-37	—	—	—
22	ECT low reference	—	W22	—	0.5	SP-0V-1	—	—	—
26	Knock sensor 1 signal A	—	W50	—	0.5	M190-C-51	—	—	—
27	Knock sensor 1 signal B	—	W51	—	0.5	M190-C-44	—	—	—
29	Knock sensor 2 signal A	—	W52	—	0.5	M190-C-43	—	—	—
3	5V reference (throttle body)	—	W43	—	0.5	SP-5V1-1	—	—	—
30	Knock sensor 2 signal B	—	W53	—	0.5	M190-C-49	—	—	—
32	Generator field duty control	—	W90	—	0.5	M190-A-45	—	—	—
33	Oil level switch signal	—	W111	—	0.5	M190-A-14	—	—	—
34	Oil pressure low reference	—	W23	—	0.5	SP-0V-1	—	—	—
35	Throttle body low reference	—	W24	—	0.5	SP-0V-1	—	—	—
37	Injector 2	—	W63	—	0.5	M190-A-3	—	—	—
38	Injector 3	—	W64	—	0.5	M190-B-U	—	—	—
39	Injector 4	—	W65	—	0.5	M190-A-12	—	—	—
40	Injector 7	—	W68	—	0.5	M190-A-1	—	—	—
41	5V reference (oil pressure)	—	W44	—	0.5	SP-5V1-1	—	—	—
43	5V reference (MAP)	—	W45	—	0.5	SP-5V1-1	—	—	—
44	5V reference (camshaft sensor)	—	W46	—	0.5	SP-5V1-1	—	—	—
5	Throttle actuator motor control 2	—	W71	—	0.5	M190-B-B	—	—	—
50	Engine oil pressure signal	—	W107	—	0.5	M190-A-13	—	—	—
52	Camshaft actuator low reference	—	W25	—	0.5	SP-0V-1	—	—	—
53	MAP low reference	—	W26	—	0.5	SP-0V-1	—	—	—
56	HO2S low reference, bank 1 sensor 1	—	W27	—	0.5	SP-0V-1	—	—	—
57	HO2S signal, bank 1 sensor 1 (pre-cat)	—	W101	—	0.5	M190-C-12	—	—	—
58	Manifold absolute pressure (MAP) signal	—	W94	—	0.5	M190-C-36	—	—	—
59	HO2S signal, bank 2 sensor 1 (pre-cat)	—	W102	—	0.5	M190-C-6	—	—	—
6	Throttle actuator motor control 1	—	W70	—	0.5	M190-B-A	—	—	—
60	HO2S low reference, bank 2 sensor 1	—	W28	—	0.5	SP-0V-1	—	—	—
61	Charge indicator signal	—	W91	—	0.5	M190-A-44	—	—	—
63	Throttle position sensor 2 signal	—	W98	—	0.5	M190-C-11	—	—	—
64	Camshaft position signal (4x)	—	W49	—	0.5	M190-C-32	—	—	—
65	Throttle position sensor 1 signal	—	W96	—	0.5	M190-C-28	—	—	—
66	Camshaft position low reference	—	W29	—	0.5	SP-0V-1	—	—	—
68	Crankshaft position signal (58x)	—	W48	—	0.5	M190-C-18	—	—	—
69	Crankshaft position low reference	—	W30	—	0.5	SP-0V-1	—	—	—
70	Ignition coil 1 control	—	W54	—	0.5	M190-C-16	—	—	—
71	Ignition coil 8 control	—	W61	—	0.5	M190-C-3	—	—	—
72	Ignition coil 7 control	—	W60	—	0.5	M190-C-9	—	—	—
73	Ignition coil 2 control	—	W55	—	0.5	M190-C-8	—	—	—
74	Ignition coil 6 control	—	W59	—	0.5	M190-C-4	—	—	—
75	Ignition coil 5 control	—	W58	—	0.5	M190-C-5	—	—	—
76	Ignition coil 4 control	—	W57	—	0.5	M190-C-1	—	—	—
77	Ignition coil 3 control	—	W56	—	0.5	M190-C-2	—	—	—
78	Coil low reference (odd bank)	—	W9	—	0.85	SP-GND-1	—	—	—
79	Coil low reference (even bank)	—	W10	—	0.85	SP-GND-1	—	—	—
8	EVAP canister purge solenoid	—	W92	—	0.5	M190-A-36	—	—	—
9	Cylinder shutoff solenoid 3 (AFM)	—	W85	—	0.5	M190-A-47	—	—	—

SP-0V

Cavity	Function	Signal	Wire	Colour	Gauge (mm²)	Destination	Terminal	Seal	Plug
1	—	—	W17	—	0.5	OEM-X1-11	—	—	—
1	—	—	W18	—	0.5	OEM-X1-23	—	—	—
1	—	—	W19	—	0.5	OEM-X1-30	—	—	—
1	—	—	W20	—	0.5	OEM-X1-38	—	—	—
1	—	—	W21	—	0.5	OEM-X1-49	—	—	—
1	—	—	W22	—	0.5	OEM-X2-22	—	—	—
1	—	—	W23	—	0.5	OEM-X2-34	—	—	—
1	—	—	W24	—	0.5	OEM-X2-35	—	—	—
1	—	—	W25	—	0.5	OEM-X2-52	—	—	—
1	—	—	W26	—	0.5	OEM-X2-53	—	—	—
1	—	—	W27	—	0.5	OEM-X2-56	—	—	—
1	—	—	W28	—	0.5	OEM-X2-60	—	—	—
1	—	—	W29	—	0.5	OEM-X2-66	—	—	—
1	—	—	W30	—	0.5	OEM-X2-69	—	—	—
1	—	—	W31	—	0.5	M190-A-18	—	—	—
1	—	—	W32	—	0.5	M190-A-19	—	—	—
1	—	—	W33	—	0.5	M190-A-20	—	—	—
1	—	—	W34	—	0.5	M190-C-14	—	—	—
1	—	—	W35	—	0.5	M190-C-15	—	—	—
1	—	—	W36	—	0.5	M190-C-23	—	—	—
1	—	—	W37	—	0.5	M190-C-30	—	—	—

SP-14V

Cavity	Function	Signal	Wire	Colour	Gauge (mm²)	Destination	Terminal	Seal	Plug
1	—	—	W1	—	0.85	OEM-X1-19	—	—	—
1	—	—	W2	—	0.85	OEM-X1-47	—	—	—
1	—	—	W3	—	0.85	M190-B-H	—	—	—
1	—	—	W4	—	0.85	M190-B-J	—	—	—
1	—	—	W5	—	0.85	M190-B-K	—	—	—
1	—	—	W6	—	0.85	M190-B-L	—	—	—

SP-5V1

Cavity	Function	Signal	Wire	Colour	Gauge (mm²)	Destination	Terminal	Seal	Plug
1	—	—	W38	—	0.5	OEM-X1-33	—	—	—
1	—	—	W39	—	0.5	OEM-X1-34	—	—	—
1	—	—	W40	—	0.5	OEM-X1-36	—	—	—
1	—	—	W41	—	0.5	OEM-X1-56	—	—	—
1	—	—	W42	—	0.5	OEM-X2-2	—	—	—
1	—	—	W43	—	0.5	OEM-X2-3	—	—	—
1	—	—	W44	—	0.5	OEM-X2-41	—	—	—
1	—	—	W45	—	0.5	OEM-X2-43	—	—	—
1	—	—	W46	—	0.5	OEM-X2-44	—	—	—
1	—	—	W47	—	0.5	M190-A-16	—	—	—

SP-GND

Cavity	Function	Signal	Wire	Colour	Gauge (mm²)	Destination	Terminal	Seal	Plug
1	—	—	W8	—	0.85	OEM-X1-73	—	—	—
1	—	—	W9	—	0.85	OEM-X2-78	—	—	—
1	—	—	W10	—	0.85	OEM-X2-79	—	—	—
1	—	—	W11	—	0.85	M190-B-G	—	—	—
1	—	—	W12	—	0.85	M190-B-W	—	—	—
1	—	—	W13	—	0.85	M190-B-X	—	—	—
1	—	—	W14	—	0.85	M190-B-Y	—	—	—
1	—	—	W15	—	0.85	M190-B-Z	—	—	—
1	—	—	W16	—	0.85	M190-B-c	—	—	—

Pin map

OEM point	OEM function	OEM family	Target point	Target function	Target family	Evidence
OEM-X1-10	HO2S signal, bank 1 sensor 2 (post-cat)	lambda_nb_in	M190-A-7	Lambda Narrow Input 1	lambda_nb_in	single_source
OEM-X1-11	HO2S low reference, bank 1 sensor 2	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X1-12	A/C refrigerant pressure signal	analog_in	M190-C-13	Analogue Voltage Input 9	analog_in	corroborated
OEM-X1-17	High speed cooling fan relay	low_side_out	M190-B-S	Low Side Injector 4	injector_out	corroborated
OEM-X1-19	Ignition 1 voltage (key hot)	power_in	M190-B-H + M190-B-J + M190-B-K + M190-B-L	Battery Positive 1 + Battery Positive 2 + Battery Positive 3 + Battery Positive 4	power_in	single_source
OEM-X1-20	Battery positive voltage (batt hot)	power_in	M190-A-38	Battery Backup	power_in	single_source
OEM-X1-23	APP sensor low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X1-24	Fuel tank pressure signal	analog_in	M190-C-7	Analogue Voltage Input 10	analog_in	corroborated
OEM-X1-29	Accelerator pedal position (APP) sensor 1 signal	analog_in	M190-C-35	Analogue Voltage Input 3	analog_in	single_source
OEM-X1-30	APP sensor low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X1-32	Accelerator pedal position (APP) sensor 2 signal	analog_in	M190-C-29	Analogue Voltage Input 5	analog_in	single_source
OEM-X1-33	5V reference (fuel tank pressure)	vref	M190-A-16	Sensor 5.0V C3	vref	single_source
OEM-X1-34	5V reference (A/C pressure)	vref	M190-A-16	Sensor 5.0V C3	vref	single_source
OEM-X1-36	5V reference (APP sensor)	vref	M190-A-16	Sensor 5.0V C3	vref	single_source
OEM-X1-37	Intake air temperature (IAT) signal	temp_in	M190-C-39	Analogue Temperature Input 2	temp_in	corroborated
OEM-X1-38	Intake air temperature (IAT) low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X1-41	Mass air flow (MAF) signal	analog_in	M190-C-42	Analogue Voltage Input 1	analog_in	corroborated
OEM-X1-47	Ignition 1 voltage (key hot)	power_in	M190-B-H + M190-B-J + M190-B-K + M190-B-L	Battery Positive 1 + Battery Positive 2 + Battery Positive 3 + Battery Positive 4	power_in	single_source
OEM-X1-48	Tachometer output	tacho_out	—	—	—	corroborated
OEM-X1-49	HO2S low reference, bank 2 sensor 2	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X1-50	Fuel pump relay control (primary)	low_side_out	M190-B-b	Low Side Injector 3	injector_out	corroborated
OEM-X1-51	Fuel pump relay control (secondary)	low_side_out	M190-A-48	Low Side Injector 5	injector_out	corroborated
OEM-X1-52	Starter enable relay control	low_side_out	M190-B-a	Low Side Injector 5	injector_out	corroborated
OEM-X1-56	5V reference (APP sensor)	vref	M190-A-16	Sensor 5.0V C3	vref	single_source
OEM-X1-57	VSS output to ABS (128k)	tacho_out	—	—	—	corroborated
OEM-X1-58	Low speed cooling fan relay	low_side_out	M190-A-40	Low Side Injector 6	injector_out	corroborated
OEM-X1-59	Powertrain relay coil control (main relay)	low_side_out	M190-A-5	Low Side Injector 4	injector_out	corroborated
OEM-X1-61	EVAP canister vent solenoid	low_side_out	M190-A-17	Low Side Injector 11	injector_out	corroborated
OEM-X1-63	A/C compressor clutch relay	low_side_out	M190-B-T	Low Side Injector 6	injector_out	corroborated
OEM-X1-64	HO2S heater low control, bank 2 sensor 2	low_side_out	M190-B-C	Half Bridge Output 3	hbridge_out	single_source
OEM-X1-65	HO2S heater low control, bank 1 sensor 2	low_side_out	M190-B-D	Half Bridge Output 4	hbridge_out	single_source
OEM-X1-68	Malfunction indicator lamp (MIL)	low_side_out	M190-A-4	Low Side Injector 12	injector_out	corroborated
OEM-X1-69	HO2S signal, bank 2 sensor 2 (post-cat)	lambda_nb_in	M190-A-6	Lambda Narrow Input 2	lambda_nb_in	single_source
OEM-X1-71	VSS high signal (manual trans)	digital_in	M190-C-25	Universal Digital Input 3	digital_in	corroborated
OEM-X1-72	VSS low signal (manual trans)	digital_in	M190-C-27	Universal Digital Input 4	digital_in	corroborated
OEM-X1-73	Power ground	ground	M190-B-G + M190-B-W + M190-B-X + M190-B-Y + M190-B-Z + M190-B-c	Battery Negative 1 + Battery Negative 2 + Battery Negative 3 + Battery Negative 4 + Battery Negative 5 + Battery Negative 6	ground	single_source
OEM-X1-9	Brake switch signal	digital_in	M190-A-21	Digital Input 1	digital_in	corroborated
OEM-X2-10	Cylinder shutoff solenoid 1 (AFM)	low_side_out	M190-A-25	Low Side Injector 7	injector_out	corroborated
OEM-X2-11	Cylinder shutoff solenoid 4 (AFM)	low_side_out	M190-A-32	Low Side Injector 10	injector_out	corroborated
OEM-X2-12	HO2S heater low control, bank 1 sensor 1	low_side_out	M190-B-E	Half Bridge Output 5	hbridge_out	single_source
OEM-X2-13	HO2S heater low control, bank 2 sensor 1	low_side_out	M190-B-F	Half Bridge Output 6	hbridge_out	single_source
OEM-X2-14	Cylinder shutoff solenoid 2 (AFM)	low_side_out	M190-A-10	Low Side Injector 8	injector_out	corroborated
OEM-X2-16	Camshaft actuator solenoid (VVT)	low_side_out	M190-A-33	Peak Hold Injector 4	injector_out	corroborated
OEM-X2-17	Injector 8	injector_out	M190-A-26	Peak Hold Injector 3	injector_out	single_source
OEM-X2-18	Injector 5	injector_out	M190-A-2	Low Side Injector 2	injector_out	single_source
OEM-X2-19	Injector 6	injector_out	M190-B-V	Low Side Injector 2	injector_out	single_source
OEM-X2-2	5V reference (crankshaft sensor)	vref	M190-A-16	Sensor 5.0V C3	vref	single_source
OEM-X2-20	Injector 1	injector_out	M190-A-11	Peak Hold Injector 1	injector_out	single_source
OEM-X2-21	Engine coolant temperature (ECT) signal	temp_in	M190-C-37	Analogue Temperature Input 1	temp_in	corroborated
OEM-X2-22	ECT low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X2-26	Knock sensor 1 signal A	knock_in	M190-C-51	Knock Input 1	knock_in	corroborated
OEM-X2-27	Knock sensor 1 signal B	knock_in	M190-C-44	Knock Input 2	knock_in	single_source
OEM-X2-29	Knock sensor 2 signal A	knock_in	M190-C-43	Knock Input 3	knock_in	corroborated
OEM-X2-3	5V reference (throttle body)	vref	M190-A-16	Sensor 5.0V C3	vref	single_source
OEM-X2-30	Knock sensor 2 signal B	knock_in	M190-C-49	Knock Input 4	knock_in	single_source
OEM-X2-32	Generator field duty control	low_side_out	M190-A-45	Peak Hold Injector 5	injector_out	corroborated
OEM-X2-33	Oil level switch signal	digital_in	M190-A-14	Digital Input 2	digital_in	corroborated
OEM-X2-34	Oil pressure low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X2-35	Throttle body low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X2-37	Injector 2	injector_out	M190-A-3	Low Side Injector 1	injector_out	single_source
OEM-X2-38	Injector 3	injector_out	M190-B-U	Low Side Injector 1	injector_out	single_source
OEM-X2-39	Injector 4	injector_out	M190-A-12	Peak Hold Injector 2	injector_out	single_source
OEM-X2-40	Injector 7	injector_out	M190-A-1	Low Side Injector 3	injector_out	single_source
OEM-X2-41	5V reference (oil pressure)	vref	M190-A-16	Sensor 5.0V C3	vref	single_source
OEM-X2-43	5V reference (MAP)	vref	M190-A-16	Sensor 5.0V C3	vref	single_source
OEM-X2-44	5V reference (camshaft sensor)	vref	M190-A-16	Sensor 5.0V C3	vref	single_source
OEM-X2-5	Throttle actuator motor control 2	hbridge_out	M190-B-B	Half Bridge Output 2	hbridge_out	corroborated
OEM-X2-50	Engine oil pressure signal	analog_in	M190-A-13	Analogue Voltage Input 11	analog_in	corroborated
OEM-X2-52	Camshaft actuator low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X2-53	MAP low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X2-56	HO2S low reference, bank 1 sensor 1	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X2-57	HO2S signal, bank 1 sensor 1 (pre-cat)	lambda_nb_in	M190-C-12	Analogue Voltage Input 7	analog_in	single_source
OEM-X2-58	Manifold absolute pressure (MAP) signal	analog_in	M190-C-36	Analogue Voltage Input 2	analog_in	corroborated
OEM-X2-59	HO2S signal, bank 2 sensor 1 (pre-cat)	lambda_nb_in	M190-C-6	Analogue Voltage Input 8	analog_in	single_source
OEM-X2-6	Throttle actuator motor control 1	hbridge_out	M190-B-A	Half Bridge Output 1	hbridge_out	corroborated
OEM-X2-60	HO2S low reference, bank 2 sensor 1	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X2-61	Charge indicator signal	low_side_out	M190-A-44	Peak Hold Injector 6	injector_out	corroborated
OEM-X2-63	Throttle position sensor 2 signal	analog_in	M190-C-11	Analogue Voltage Input 6	analog_in	single_source
OEM-X2-64	Camshaft position signal (4x)	trigger_in	M190-C-32	Universal Digital Input 2	digital_in	single_source
OEM-X2-65	Throttle position sensor 1 signal	analog_in	M190-C-28	Analogue Voltage Input 4	analog_in	single_source
OEM-X2-66	Camshaft position low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X2-68	Crankshaft position signal (58x)	trigger_in	M190-C-18	Universal Digital Input 1	digital_in	single_source
OEM-X2-69	Crankshaft position low reference	sensor_ground	M190-A-18 + M190-A-19 + M190-A-20 + M190-C-14 + M190-C-15 + M190-C-23 + M190-C-30	Sensor 0V C1 + Sensor 0V C2 + Sensor 0V C3 + Sensor 0V A1 + Sensor 0V A2 + Sensor 0V B1 + Sensor 0V B2	sensor_ground	single_source
OEM-X2-70	Ignition coil 1 control	ignition_out	M190-C-16	Low Side Ignition 1	ignition_out	single_source
OEM-X2-71	Ignition coil 8 control	ignition_out	M190-C-3	Low Side Ignition 8	ignition_out	single_source
OEM-X2-72	Ignition coil 7 control	ignition_out	M190-C-9	Low Side Ignition 7	ignition_out	single_source
OEM-X2-73	Ignition coil 2 control	ignition_out	M190-C-8	Low Side Ignition 2	ignition_out	single_source
OEM-X2-74	Ignition coil 6 control	ignition_out	M190-C-4	Low Side Ignition 6	ignition_out	single_source
OEM-X2-75	Ignition coil 5 control	ignition_out	M190-C-5	Low Side Ignition 5	ignition_out	single_source
OEM-X2-76	Ignition coil 4 control	ignition_out	M190-C-1	Low Side Ignition 4	ignition_out	single_source
OEM-X2-77	Ignition coil 3 control	ignition_out	M190-C-2	Low Side Ignition 3	ignition_out	single_source
OEM-X2-78	Coil low reference (odd bank)	ground	M190-B-G + M190-B-W + M190-B-X + M190-B-Y + M190-B-Z + M190-B-c	Battery Negative 1 + Battery Negative 2 + Battery Negative 3 + Battery Negative 4 + Battery Negative 5 + Battery Negative 6	ground	single_source
OEM-X2-79	Coil low reference (even bank)	ground	M190-B-G + M190-B-W + M190-B-X + M190-B-Y + M190-B-Z + M190-B-c	Battery Negative 1 + Battery Negative 2 + Battery Negative 3 + Battery Negative 4 + Battery Negative 5 + Battery Negative 6	ground	single_source
OEM-X2-8	EVAP canister purge solenoid	low_side_out	M190-A-36	Peak Hold Injector 7	injector_out	corroborated
OEM-X2-9	Cylinder shutoff solenoid 3 (AFM)	low_side_out	M190-A-47	Low Side Injector 9	injector_out	corroborated

Cut list

Wire	From	To	Gauge (mm²)	Length	Signal	Ident
W1	OEM-X1-19	SP-14V-1	0.85	no route	Ignition 1 voltage (key hot)	—
W2	OEM-X1-47	SP-14V-1	0.85	no route	Ignition 1 voltage (key hot)	—
W3	SP-14V-1	M190-B-H	0.85	no route	Battery Positive 1	—
W4	SP-14V-1	M190-B-J	0.85	no route	Battery Positive 2	—
W5	SP-14V-1	M190-B-K	0.85	no route	Battery Positive 3	—
W6	SP-14V-1	M190-B-L	0.85	no route	Battery Positive 4	—
W7	OEM-X1-20	M190-A-38	0.85	no route	Battery positive voltage (batt hot)	—
W8	OEM-X1-73	SP-GND-1	0.85	no route	Power ground	—
W9	OEM-X2-78	SP-GND-1	0.85	no route	Coil low reference (odd bank)	—
W10	OEM-X2-79	SP-GND-1	0.85	no route	Coil low reference (even bank)	—
W11	SP-GND-1	M190-B-G	0.85	no route	Battery Negative 1	—
W12	SP-GND-1	M190-B-W	0.85	no route	Battery Negative 2	—
W13	SP-GND-1	M190-B-X	0.85	no route	Battery Negative 3	—
W14	SP-GND-1	M190-B-Y	0.85	no route	Battery Negative 4	—
W15	SP-GND-1	M190-B-Z	0.85	no route	Battery Negative 5	—
W16	SP-GND-1	M190-B-c	0.85	no route	Battery Negative 6	—
W17	OEM-X1-11	SP-0V-1	0.5	no route	HO2S low reference, bank 1 sensor 2	—
W18	OEM-X1-23	SP-0V-1	0.5	no route	APP sensor low reference	—
W19	OEM-X1-30	SP-0V-1	0.5	no route	APP sensor low reference	—
W20	OEM-X1-38	SP-0V-1	0.5	no route	Intake air temperature (IAT) low reference	—
W21	OEM-X1-49	SP-0V-1	0.5	no route	HO2S low reference, bank 2 sensor 2	—
W22	OEM-X2-22	SP-0V-1	0.5	no route	ECT low reference	—
W23	OEM-X2-34	SP-0V-1	0.5	no route	Oil pressure low reference	—
W24	OEM-X2-35	SP-0V-1	0.5	no route	Throttle body low reference	—
W25	OEM-X2-52	SP-0V-1	0.5	no route	Camshaft actuator low reference	—
W26	OEM-X2-53	SP-0V-1	0.5	no route	MAP low reference	—
W27	OEM-X2-56	SP-0V-1	0.5	no route	HO2S low reference, bank 1 sensor 1	—
W28	OEM-X2-60	SP-0V-1	0.5	no route	HO2S low reference, bank 2 sensor 1	—
W29	OEM-X2-66	SP-0V-1	0.5	no route	Camshaft position low reference	—
W30	OEM-X2-69	SP-0V-1	0.5	no route	Crankshaft position low reference	—
W31	SP-0V-1	M190-A-18	0.5	no route	Sensor 0V C1	—
W32	SP-0V-1	M190-A-19	0.5	no route	Sensor 0V C2	—
W33	SP-0V-1	M190-A-20	0.5	no route	Sensor 0V C3	—
W34	SP-0V-1	M190-C-14	0.5	no route	Sensor 0V A1	—
W35	SP-0V-1	M190-C-15	0.5	no route	Sensor 0V A2	—
W36	SP-0V-1	M190-C-23	0.5	no route	Sensor 0V B1	—
W37	SP-0V-1	M190-C-30	0.5	no route	Sensor 0V B2	—
W38	OEM-X1-33	SP-5V1-1	0.5	no route	5V reference (fuel tank pressure)	—
W39	OEM-X1-34	SP-5V1-1	0.5	no route	5V reference (A/C pressure)	—
W40	OEM-X1-36	SP-5V1-1	0.5	no route	5V reference (APP sensor)	—
W41	OEM-X1-56	SP-5V1-1	0.5	no route	5V reference (APP sensor)	—
W42	OEM-X2-2	SP-5V1-1	0.5	no route	5V reference (crankshaft sensor)	—
W43	OEM-X2-3	SP-5V1-1	0.5	no route	5V reference (throttle body)	—
W44	OEM-X2-41	SP-5V1-1	0.5	no route	5V reference (oil pressure)	—
W45	OEM-X2-43	SP-5V1-1	0.5	no route	5V reference (MAP)	—
W46	OEM-X2-44	SP-5V1-1	0.5	no route	5V reference (camshaft sensor)	—
W47	SP-5V1-1	M190-A-16	0.5	no route	Sensor 5.0V C3	—
W48	OEM-X2-68	M190-C-18	0.5	no route	Crankshaft position signal (58x)	—
W49	OEM-X2-64	M190-C-32	0.5	no route	Camshaft position signal (4x)	—
W50	OEM-X2-26	M190-C-51	0.5	no route	Knock sensor 1 signal A	—
W51	OEM-X2-27	M190-C-44	0.5	no route	Knock sensor 1 signal B	—
W52	OEM-X2-29	M190-C-43	0.5	no route	Knock sensor 2 signal A	—
W53	OEM-X2-30	M190-C-49	0.5	no route	Knock sensor 2 signal B	—
W54	OEM-X2-70	M190-C-16	0.5	no route	Ignition coil 1 control	—
W55	OEM-X2-73	M190-C-8	0.5	no route	Ignition coil 2 control	—
W56	OEM-X2-77	M190-C-2	0.5	no route	Ignition coil 3 control	—
W57	OEM-X2-76	M190-C-1	0.5	no route	Ignition coil 4 control	—
W58	OEM-X2-75	M190-C-5	0.5	no route	Ignition coil 5 control	—
W59	OEM-X2-74	M190-C-4	0.5	no route	Ignition coil 6 control	—
W60	OEM-X2-72	M190-C-9	0.5	no route	Ignition coil 7 control	—
W61	OEM-X2-71	M190-C-3	0.5	no route	Ignition coil 8 control	—
W62	OEM-X2-20	M190-A-11	0.5	no route	Injector 1	—
W63	OEM-X2-37	M190-A-3	0.5	no route	Injector 2	—
W64	OEM-X2-38	M190-B-U	0.5	no route	Injector 3	—
W65	OEM-X2-39	M190-A-12	0.5	no route	Injector 4	—
W66	OEM-X2-18	M190-A-2	0.5	no route	Injector 5	—
W67	OEM-X2-19	M190-B-V	0.5	no route	Injector 6	—
W68	OEM-X2-40	M190-A-1	0.5	no route	Injector 7	—
W69	OEM-X2-17	M190-A-26	0.5	no route	Injector 8	—
W70	OEM-X2-6	M190-B-A	0.5	no route	Throttle actuator motor control 1	—
W71	OEM-X2-5	M190-B-B	0.5	no route	Throttle actuator motor control 2	—
W72	OEM-X1-50	M190-B-b	0.5	no route	Fuel pump relay control (primary)	—
W73	OEM-X1-59	M190-A-5	0.5	no route	Powertrain relay coil control (main relay)	—
W74	OEM-X1-17	M190-B-S	0.5	no route	High speed cooling fan relay	—
W75	OEM-X1-51	M190-A-48	0.5	no route	Fuel pump relay control (secondary)	—
W76	OEM-X1-52	M190-B-a	0.5	no route	Starter enable relay control	—
W77	OEM-X1-58	M190-A-40	0.5	no route	Low speed cooling fan relay	—
W78	OEM-X1-63	M190-B-T	0.5	no route	A/C compressor clutch relay	—
W79	OEM-X1-64	M190-B-C	0.5	no route	HO2S heater low control, bank 2 sensor 2	—
W80	OEM-X1-65	M190-B-D	0.5	no route	HO2S heater low control, bank 1 sensor 2	—
W81	OEM-X2-12	M190-B-E	0.5	no route	HO2S heater low control, bank 1 sensor 1	—
W82	OEM-X2-13	M190-B-F	0.5	no route	HO2S heater low control, bank 2 sensor 1	—
W83	OEM-X2-10	M190-A-25	0.5	no route	Cylinder shutoff solenoid 1 (AFM)	—
W84	OEM-X2-14	M190-A-10	0.5	no route	Cylinder shutoff solenoid 2 (AFM)	—
W85	OEM-X2-9	M190-A-47	0.5	no route	Cylinder shutoff solenoid 3 (AFM)	—
W86	OEM-X2-11	M190-A-32	0.5	no route	Cylinder shutoff solenoid 4 (AFM)	—
W87	OEM-X1-61	M190-A-17	0.5	no route	EVAP canister vent solenoid	—
W88	OEM-X1-68	M190-A-4	0.5	no route	Malfunction indicator lamp (MIL)	—
W89	OEM-X2-16	M190-A-33	0.5	no route	Camshaft actuator solenoid (VVT)	—
W90	OEM-X2-32	M190-A-45	0.5	no route	Generator field duty control	—
W91	OEM-X2-61	M190-A-44	0.5	no route	Charge indicator signal	—
W92	OEM-X2-8	M190-A-36	0.5	no route	EVAP canister purge solenoid	—
W93	OEM-X1-41	M190-C-42	0.5	no route	Mass air flow (MAF) signal	—
W94	OEM-X2-58	M190-C-36	0.5	no route	Manifold absolute pressure (MAP) signal	—
W95	OEM-X1-29	M190-C-35	0.5	no route	Accelerator pedal position (APP) sensor 1 signal	—
W96	OEM-X2-65	M190-C-28	0.5	no route	Throttle position sensor 1 signal	—
W97	OEM-X1-32	M190-C-29	0.5	no route	Accelerator pedal position (APP) sensor 2 signal	—
W98	OEM-X2-63	M190-C-11	0.5	no route	Throttle position sensor 2 signal	—
W99	OEM-X1-10	M190-A-7	0.5	no route	HO2S signal, bank 1 sensor 2 (post-cat)	—
W100	OEM-X1-69	M190-A-6	0.5	no route	HO2S signal, bank 2 sensor 2 (post-cat)	—
W101	OEM-X2-57	M190-C-12	0.5	no route	HO2S signal, bank 1 sensor 1 (pre-cat)	—
W102	OEM-X2-59	M190-C-6	0.5	no route	HO2S signal, bank 2 sensor 1 (pre-cat)	—
W103	OEM-X2-21	M190-C-37	0.5	no route	Engine coolant temperature (ECT) signal	—
W104	OEM-X1-37	M190-C-39	0.5	no route	Intake air temperature (IAT) signal	—
W105	OEM-X1-12	M190-C-13	0.5	no route	A/C refrigerant pressure signal	—
W106	OEM-X1-24	M190-C-7	0.5	no route	Fuel tank pressure signal	—
W107	OEM-X2-50	M190-A-13	0.5	no route	Engine oil pressure signal	—
W108	OEM-X1-71	M190-C-25	0.5	no route	VSS high signal (manual trans)	—
W109	OEM-X1-72	M190-C-27	0.5	no route	VSS low signal (manual trans)	—
W110	OEM-X1-9	M190-A-21	0.5	no route	Brake switch signal	—
W111	OEM-X2-33	M190-A-14	0.5	no route	Oil level switch signal	—

Bill of materials

Category	Part number	Manufacturer	Description	Qty	Unit

ECU setup sheet

Role	Engine ref	Engine signal	Sensor	ECU point	ECU function	ECU class	Setup flag
No configured channels.

Findings

Open (26)

Severity	Code	Subject	Message
warn	DBW_MOTOR_CURRENT	M190-B-A	Cannot confirm M190 can drive the throttle motor: M190-B-A "Half Bridge Output 1" is rated 12.0 A, but the motor current at OEM-X2-6 is unknown. Add the motor's peak current from a source, or measure the motor resistance: peak ≈ 14 V ÷ R (Hondata measured 4.9 A for a Civic Si body, 10.4 A for a ZDX body; holding current is about 1 A).
warn	DBW_MOTOR_CURRENT	M190-B-B	Cannot confirm M190 can drive the throttle motor: M190-B-B "Half Bridge Output 2" is rated 12.0 A, but the motor current at OEM-X2-5 is unknown. Add the motor's peak current from a source, or measure the motor resistance: peak ≈ 14 V ÷ R (Hondata measured 4.9 A for a Civic Si body, 10.4 A for a ZDX body; holding current is about 1 A).
warn	NET_FAMILY	OEM-X1-64 ↔ M190-B-C	OEM-X1-64 "HO2S heater low control, bank 2 sensor 2" [low_side_out] is wired to M190-B-C "Half Bridge Output 3" [hbridge_out]. A half-bridge can act as a low-side switch only if configured that way.
warn	NET_FAMILY	OEM-X1-65 ↔ M190-B-D	OEM-X1-65 "HO2S heater low control, bank 1 sensor 2" [low_side_out] is wired to M190-B-D "Half Bridge Output 4" [hbridge_out]. A half-bridge can act as a low-side switch only if configured that way.
warn	NET_FAMILY	OEM-X2-12 ↔ M190-B-E	OEM-X2-12 "HO2S heater low control, bank 1 sensor 1" [low_side_out] is wired to M190-B-E "Half Bridge Output 5" [hbridge_out]. A half-bridge can act as a low-side switch only if configured that way.
warn	NET_FAMILY	OEM-X2-13 ↔ M190-B-F	OEM-X2-13 "HO2S heater low control, bank 2 sensor 1" [low_side_out] is wired to M190-B-F "Half Bridge Output 6" [hbridge_out]. A half-bridge can act as a low-side switch only if configured that way.
warn	NET_FAMILY	OEM-X2-64 ↔ M190-C-32	OEM-X2-64 "Camshaft position signal (4x)" [trigger_in] is wired to M190-C-32 "Universal Digital Input 2" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot.
warn	NET_FAMILY	OEM-X2-68 ↔ M190-C-18	OEM-X2-68 "Crankshaft position signal (58x)" [trigger_in] is wired to M190-C-18 "Universal Digital Input 1" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot.
info	NET_FAMILY	OEM-X1-17 ↔ M190-B-S	OEM-X1-17 "High speed cooling fan relay" [low_side_out] is wired to M190-B-S "Low Side Injector 4" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X1-50 ↔ M190-B-b	OEM-X1-50 "Fuel pump relay control (primary)" [low_side_out] is wired to M190-B-b "Low Side Injector 3" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X1-51 ↔ M190-A-48	OEM-X1-51 "Fuel pump relay control (secondary)" [low_side_out] is wired to M190-A-48 "Low Side Injector 5" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X1-52 ↔ M190-B-a	OEM-X1-52 "Starter enable relay control" [low_side_out] is wired to M190-B-a "Low Side Injector 5" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X1-58 ↔ M190-A-40	OEM-X1-58 "Low speed cooling fan relay" [low_side_out] is wired to M190-A-40 "Low Side Injector 6" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X1-59 ↔ M190-A-5	OEM-X1-59 "Powertrain relay coil control (main relay)" [low_side_out] is wired to M190-A-5 "Low Side Injector 4" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X1-61 ↔ M190-A-17	OEM-X1-61 "EVAP canister vent solenoid" [low_side_out] is wired to M190-A-17 "Low Side Injector 11" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X1-63 ↔ M190-B-T	OEM-X1-63 "A/C compressor clutch relay" [low_side_out] is wired to M190-B-T "Low Side Injector 6" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X1-68 ↔ M190-A-4	OEM-X1-68 "Malfunction indicator lamp (MIL)" [low_side_out] is wired to M190-A-4 "Low Side Injector 12" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X2-10 ↔ M190-A-25	OEM-X2-10 "Cylinder shutoff solenoid 1 (AFM)" [low_side_out] is wired to M190-A-25 "Low Side Injector 7" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X2-11 ↔ M190-A-32	OEM-X2-11 "Cylinder shutoff solenoid 4 (AFM)" [low_side_out] is wired to M190-A-32 "Low Side Injector 10" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X2-14 ↔ M190-A-10	OEM-X2-14 "Cylinder shutoff solenoid 2 (AFM)" [low_side_out] is wired to M190-A-10 "Low Side Injector 8" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X2-16 ↔ M190-A-33	OEM-X2-16 "Camshaft actuator solenoid (VVT)" [low_side_out] is wired to M190-A-33 "Peak Hold Injector 4" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X2-32 ↔ M190-A-45	OEM-X2-32 "Generator field duty control" [low_side_out] is wired to M190-A-45 "Peak Hold Injector 5" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X2-61 ↔ M190-A-44	OEM-X2-61 "Charge indicator signal" [low_side_out] is wired to M190-A-44 "Peak Hold Injector 6" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X2-8 ↔ M190-A-36	OEM-X2-8 "EVAP canister purge solenoid" [low_side_out] is wired to M190-A-36 "Peak Hold Injector 7" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	NET_FAMILY	OEM-X2-9 ↔ M190-A-47	OEM-X2-9 "Cylinder shutoff solenoid 3 (AFM)" [low_side_out] is wired to M190-A-47 "Low Side Injector 9" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency.
info	UNMAPPED	OEM	2 optional OEM pins are not mapped: OEM-X1-48 Tachometer output; OEM-X1-57 VSS output to ABS (128k)

Accepted (0)

Code	Subject	Reason	By

Notes

Auto-mapped by auto_map() from the library pin data on 2026-10-06. Review every wire against both manuals before building. Not wired: - OEM-X1 48: Tachometer output: no free tacho/frequency_out/low_side/ls_hs on MoTeC M190 - OEM-X1 57: VSS output to ABS (128k): no free frequency_out/tacho/low_side/ls_hs on MoTeC M190

Sources

Reliability	Kind	Title	URL	Archive	Captured	SHA-256
4	vendor_doc	MaxxECU webhelp: Wiring — plug-in ECU Chevrolet Corvette C6 (GM E38 ECM)	http://www.maxxecu.com/webhelp/wirings-pluginecu-chevrolet_corvette_c6_e38_ecm.html	—	—	—
4	vendor_doc	MoTeC: M1 ECU Hardware manual (7 Nov 2013) — M130/M150/M170/M190 pinout tables	https://web.archive.org/web/2023id_/https://www.motec.com.au/hessian/uploads/M1_ECU_Hardware_c2517380e4.pdf	—	2026-10-05	03dc5975f739
2	community_copy	lt1swap.com: E38 ECM Connector Pinouts	https://lt1swap.com/E38 ECM Connector Pinouts.htm	—	—	—