MX-5 Miata NB1 1999-00 (BP-4W) → AMP EFI MS3Pro Mini (auto)
MX-5 Miata NB1 1999-00 (BP-4W) — AMP EFI — MS3Pro Mini
Drawn by Michael Gnankou · Rev 0 · proposal · 2026-10-08
Before you start
| Status | proposal · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | none |
| Size of the job | 35 wires · 7 connectors · 3 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-1-B | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-3-M | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | MS3PROMINI-A-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-3-A | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-3-B | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-3-C | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | SP-GND-1 | MS3PROMINI-A-22 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | SP-GND-1 | MS3PROMINI-A-23 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | OEM-3-F | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | SP-0V-1 | MS3PROMINI-A-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-2-I | MS3PROMINI-A-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-2-J | MS3PROMINI-A-30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-2-H | MS3PROMINI-A-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-3-G | MS3PROMINI-A-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-3-H | MS3PROMINI-A-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-3-W | MS3PROMINI-A-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-3-X | MS3PROMINI-A-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-3-Y | MS3PROMINI-A-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-3-Z | MS3PROMINI-A-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-1-I | MS3PROMINI-A-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-1-R | MS3PROMINI-A-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-1-S | MS3PROMINI-A-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-3-N | MS3PROMINI-A-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-3-O | MS3PROMINI-A-8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-1-E | MS3PROMINI-A-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-2-L | MS3PROMINI-A-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-3-E | MS3PROMINI-A-28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-2-C | MS3PROMINI-A-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-3-J | MS3PROMINI-A-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-2-E | MS3PROMINI-A-26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-2-B | MS3PROMINI-A-27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-2-A | MS3PROMINI-A-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-2-D | MS3PROMINI-A-34 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-1-F | MS3PROMINI-A-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-1-G | MS3PROMINI-A-35 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | MS3PROMINI-A-1 | MS3PROMINI-A-21 | open (OL) | +12 V supply must not touch sensor ground | |
| 2 | MS3PROMINI-A-1 | MS3PROMINI-A-22 | open (OL) | +12 V supply must not touch power ground | |
| 3 | MS3PROMINI-A-2 | MS3PROMINI-A-21 | open (OL) | 5 V sensor reference must not touch sensor ground | |
| 4 | MS3PROMINI-A-2 | MS3PROMINI-A-22 | open (OL) | 5 V sensor reference must not touch power ground | |
| 5 | MS3PROMINI-A-1 | MS3PROMINI-A-2 | open (OL) | +12 V supply must not touch 5 V sensor reference |
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
MS3PROMINI-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 12V+ switched power in | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 10 | Injector out F | — | W16 | — | 0.5 | OEM-3-W | — | — | — |
| 11 | Injector out G | — | W17 | — | 0.5 | OEM-3-X | — | — | — |
| 12 | Injector out H | — | W18 | — | 0.5 | OEM-3-Y | — | — | — |
| 13 | Analog in 1 | — | W26 | — | 0.5 | OEM-2-L | — | — | — |
| 14 | Analog in 2 | — | W28 | — | 0.5 | OEM-2-C | — | — | — |
| 15 | Analog in 3 | — | W29 | — | 0.5 | OEM-3-J | — | — | — |
| 16 | Analog in 4 | — | W32 | — | 0.5 | OEM-2-A | — | — | — |
| 17 | Spark out A | — | W14 | — | 0.5 | OEM-3-G | — | — | — |
| 18 | Spark out B | — | W15 | — | 0.5 | OEM-3-H | — | — | — |
| 19 | Spark out C | — | — | — | — | — | — | — | — |
| 2 | +5V VREF out | — | W11 | — | 0.5 | OEM-2-I | — | — | — |
| 20 | Spark out D | — | — | — | — | — | — | — | — |
| 21 | Sensor ground | — | W10 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | Power ground | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 23 | Power ground | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 24 | CAN Low | — | — | — | — | — | — | — | — |
| 25 | CAN High | — | — | — | — | — | — | — | — |
| 26 | CLT in | — | W30 | — | 0.5 | OEM-2-E | — | — | — |
| 27 | IAT in | — | W31 | — | 0.5 | OEM-2-B | — | — | — |
| 28 | TPS in | — | W27 | — | 0.5 | OEM-3-E | — | — | — |
| 29 | Digital switched in 1 / Flex fuel | — | W34 | — | 0.5 | OEM-1-F | — | — | — |
| 3 | PWM out 1 / Idle | — | W21 | — | 0.5 | OEM-1-R | — | — | — |
| 30 | CKP+ | — | W12 | — | 0.5 | OEM-2-J | — | — | — |
| 31 | CKP- | — | — | — | — | — | — | — | — |
| 32 | CMP+ | — | W13 | — | 0.5 | OEM-2-H | — | — | — |
| 33 | CMP- | — | — | — | — | — | — | — | — |
| 34 | Digital frequency in 1 (Hall) | — | W33 | — | 0.5 | OEM-2-D | — | — | — |
| 35 | Digital frequency in 2 (Hall) | — | W35 | — | 0.5 | OEM-1-G | — | — | — |
| 4 | Fuel pump out | — | W20 | — | 0.5 | OEM-1-I | — | — | — |
| 5 | Injector out A | — | W19 | — | 0.5 | OEM-3-Z | — | — | — |
| 6 | Injector out B | — | W22 | — | 0.5 | OEM-1-S | — | — | — |
| 7 | Injector out C | — | W23 | — | 0.5 | OEM-3-N | — | — | — |
| 8 | Injector out D | — | W24 | — | 0.5 | OEM-3-O | — | — | — |
| 9 | Injector out E | — | W25 | — | 0.5 | OEM-1-E | — | — | — |
OEM-1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A | Constant +12V | — | — | — | — | — | — | — | — |
| B | ECU power +14V (main relay) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| E | Malfunction indicator lamp (MIL) | — | W25 | — | 0.5 | MS3PROMINI-A-9 | — | — | — |
| F | Brake switch | — | W34 | — | 0.5 | MS3PROMINI-A-29 | — | — | — |
| G | Power steering pressure switch | — | W35 | — | 0.5 | MS3PROMINI-A-35 | — | — | — |
| I | Condenser fan relay | — | W20 | — | 0.5 | MS3PROMINI-A-4 | — | — | — |
| O | Alternator control | — | — | — | — | — | — | — | — |
| P | A/C request | — | — | — | — | — | — | — | — |
| Q | Charge lamp | — | — | — | — | — | — | — | — |
| R | Cooling fan relay | — | W21 | — | 0.5 | MS3PROMINI-A-3 | — | — | — |
| S | A/C clutch relay | — | W22 | — | 0.5 | MS3PROMINI-A-6 | — | — | — |
| U | Front O2 heater | — | — | — | — | — | — | — | — |
| V | Neutral switch | — | — | — | — | — | — | — | — |
OEM-2
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A | Fuel tank pressure | — | W32 | — | 0.5 | MS3PROMINI-A-16 | — | — | — |
| B | Intake air temperature (IAT) | — | W31 | — | 0.5 | MS3PROMINI-A-27 | — | — | — |
| C | Front O2 signal | — | W28 | — | 0.5 | MS3PROMINI-A-14 | — | — | — |
| D | Vehicle speed | — | W33 | — | 0.5 | MS3PROMINI-A-34 | — | — | — |
| E | Coolant temperature (ECT) | — | W30 | — | 0.5 | MS3PROMINI-A-26 | — | — | — |
| F | Knock sensor | — | — | — | — | — | — | — | — |
| H | Cam position (CMP) | — | W13 | — | 0.5 | MS3PROMINI-A-32 | — | — | — |
| I | +5V sensor supply | — | W11 | — | 0.5 | MS3PROMINI-A-2 | — | — | — |
| J | Crank position (CKP) | — | W12 | — | 0.5 | MS3PROMINI-A-30 | — | — | — |
| K | Tachometer output | — | — | — | — | — | — | — | — |
| L | Mass air flow (MAF) | — | W26 | — | 0.5 | MS3PROMINI-A-13 | — | — | — |
| M | EGR valve | — | — | — | — | — | — | — | — |
| N | EGR valve | — | — | — | — | — | — | — | — |
| O | EGR valve | — | — | — | — | — | — | — | — |
| P | EGR valve | — | — | — | — | — | — | — | — |
OEM-3
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A | Power ground | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| B | Power ground | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| C | Power ground | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| E | Throttle position (TPS) | — | W27 | — | 0.5 | MS3PROMINI-A-28 | — | — | — |
| F | Signal ground | — | W9 | — | 0.5 | SP-0V-1 | — | — | — |
| G | Ignition 1 (coils 1+4, wasted spark) | — | W14 | — | 0.5 | MS3PROMINI-A-17 | — | — | — |
| H | Ignition 2 (coils 2+3, wasted spark) | — | W15 | — | 0.5 | MS3PROMINI-A-18 | — | — | — |
| I | Clutch switch | — | — | — | — | — | — | — | — |
| J | Rear O2 signal | — | W29 | — | 0.5 | MS3PROMINI-A-15 | — | — | — |
| K | Fuel level | — | — | — | — | — | — | — | — |
| L | Evap purge solenoid | — | — | — | — | — | — | — | — |
| M | ISC valve +14V feed | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| N | Fuel pump relay | — | W23 | — | 0.5 | MS3PROMINI-A-7 | — | — | — |
| O | ISC valve low side | — | W24 | — | 0.5 | MS3PROMINI-A-8 | — | — | — |
| Q | VICS solenoid (intake butterflies) | — | — | — | — | — | — | — | — |
| S | EGR boost sensor | — | — | — | — | — | — | — | — |
| T | EGR boost solenoid | — | — | — | — | — | — | — | — |
| U | Canister drain cut valve (CDCV) | — | — | — | — | — | — | — | — |
| V | Rear O2 heater | — | — | — | — | — | — | — | — |
| W | Injector 1 | — | W16 | — | 0.5 | MS3PROMINI-A-10 | — | — | — |
| X | Injector 2 | — | W17 | — | 0.5 | MS3PROMINI-A-11 | — | — | — |
| Y | Injector 3 | — | W18 | — | 0.5 | MS3PROMINI-A-12 | — | — | — |
| Z | Injector 4 | — | W19 | — | 0.5 | MS3PROMINI-A-5 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W9 | — | 0.5 | OEM-3-F | — | — | — |
| 1 | — | — | W10 | — | 0.5 | MS3PROMINI-A-21 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-1-B | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-3-M | — | — | — |
| 1 | — | — | W3 | — | 0.85 | MS3PROMINI-A-1 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W4 | — | 0.85 | OEM-3-A | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-3-B | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-3-C | — | — | — |
| 1 | — | — | W7 | — | 0.85 | MS3PROMINI-A-22 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | MS3PROMINI-A-23 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-1-A | Constant +12V | power_in | — | — | — | single_source | |
| OEM-1-B | ECU power +14V (main relay) | power_in | MS3PROMINI-A-1 | 12V+ switched power in | power_in | single_source | |
| OEM-1-E | Malfunction indicator lamp (MIL) | low_side_out | MS3PROMINI-A-9 | Injector out E | injector_out | single_source | |
| OEM-1-F | Brake switch | digital_in | MS3PROMINI-A-29 | Digital switched in 1 / Flex fuel | digital_in | single_source | |
| OEM-1-G | Power steering pressure switch | digital_in | MS3PROMINI-A-35 | Digital frequency in 2 (Hall) | digital_in | single_source | |
| OEM-1-I | Condenser fan relay | low_side_out | MS3PROMINI-A-4 | Fuel pump out | low_side_out | single_source | |
| OEM-1-O | Alternator control | low_side_out | — | — | — | single_source | |
| OEM-1-P | A/C request | digital_in | — | — | — | single_source | |
| OEM-1-Q | Charge lamp | low_side_out | — | — | — | single_source | |
| OEM-1-R | Cooling fan relay | low_side_out | MS3PROMINI-A-3 | PWM out 1 / Idle | low_side_out | single_source | |
| OEM-1-S | A/C clutch relay | low_side_out | MS3PROMINI-A-6 | Injector out B | injector_out | single_source | |
| OEM-1-U | Front O2 heater | low_side_out | — | — | — | single_source | |
| OEM-1-V | Neutral switch | digital_in | — | — | — | single_source | |
| OEM-2-A | Fuel tank pressure | analog_in | MS3PROMINI-A-16 | Analog in 4 | analog_in | single_source | |
| OEM-2-B | Intake air temperature (IAT) | temp_in | MS3PROMINI-A-27 | IAT in | temp_in | single_source | |
| OEM-2-C | Front O2 signal | lambda_nb_in | MS3PROMINI-A-14 | Analog in 2 | analog_in | single_source | |
| OEM-2-D | Vehicle speed | digital_in | MS3PROMINI-A-34 | Digital frequency in 1 (Hall) | digital_in | single_source | |
| OEM-2-E | Coolant temperature (ECT) | temp_in | MS3PROMINI-A-26 | CLT in | temp_in | single_source | |
| OEM-2-F | Knock sensor | knock_in | — | — | — | single_source | |
| OEM-2-H | Cam position (CMP) | trigger_in | MS3PROMINI-A-32 | CMP+ | trigger_in | single_source | |
| OEM-2-I | +5V sensor supply | vref | MS3PROMINI-A-2 | +5V VREF out | vref | single_source | |
| OEM-2-J | Crank position (CKP) | trigger_in | MS3PROMINI-A-30 | CKP+ | trigger_in | single_source | |
| OEM-2-K | Tachometer output | tacho_out | — | — | — | single_source | |
| OEM-2-L | Mass air flow (MAF) | analog_in | MS3PROMINI-A-13 | Analog in 1 | analog_in | single_source | |
| OEM-2-M | EGR valve | low_side_out | — | — | — | single_source | |
| OEM-2-N | EGR valve | low_side_out | — | — | — | single_source | |
| OEM-2-O | EGR valve | low_side_out | — | — | — | single_source | |
| OEM-2-P | EGR valve | low_side_out | — | — | — | single_source | |
| OEM-3-A | Power ground | ground | MS3PROMINI-A-22 + MS3PROMINI-A-23 | Power ground + Power ground | ground | single_source | |
| OEM-3-B | Power ground | ground | MS3PROMINI-A-22 + MS3PROMINI-A-23 | Power ground + Power ground | ground | single_source | |
| OEM-3-C | Power ground | ground | MS3PROMINI-A-22 + MS3PROMINI-A-23 | Power ground + Power ground | ground | single_source | |
| OEM-3-E | Throttle position (TPS) | analog_in | MS3PROMINI-A-28 | TPS in | analog_in | single_source | |
| OEM-3-F | Signal ground | sensor_ground | MS3PROMINI-A-21 | Sensor ground | sensor_ground | single_source | |
| OEM-3-G | Ignition 1 (coils 1+4, wasted spark) | ignition_out | MS3PROMINI-A-17 | Spark out A | ignition_out | single_source | |
| OEM-3-H | Ignition 2 (coils 2+3, wasted spark) | ignition_out | MS3PROMINI-A-18 | Spark out B | ignition_out | single_source | |
| OEM-3-I | Clutch switch | digital_in | — | — | — | single_source | |
| OEM-3-J | Rear O2 signal | lambda_nb_in | MS3PROMINI-A-15 | Analog in 3 | analog_in | single_source | |
| OEM-3-K | Fuel level | analog_in | — | — | — | single_source | |
| OEM-3-L | Evap purge solenoid | low_side_out | — | — | — | single_source | |
| OEM-3-M | ISC valve +14V feed | power_in | MS3PROMINI-A-1 | 12V+ switched power in | power_in | single_source | |
| OEM-3-N | Fuel pump relay | low_side_out | MS3PROMINI-A-7 | Injector out C | injector_out | single_source | |
| OEM-3-O | ISC valve low side | low_side_out | MS3PROMINI-A-8 | Injector out D | injector_out | single_source | |
| OEM-3-Q | VICS solenoid (intake butterflies) | low_side_out | — | — | — | single_source | |
| OEM-3-S | EGR boost sensor | analog_in | — | — | — | single_source | |
| OEM-3-T | EGR boost solenoid | low_side_out | — | — | — | single_source | |
| OEM-3-U | Canister drain cut valve (CDCV) | low_side_out | — | — | — | single_source | |
| OEM-3-V | Rear O2 heater | low_side_out | — | — | — | single_source | |
| OEM-3-W | Injector 1 | injector_out | MS3PROMINI-A-10 | Injector out F | injector_out | single_source | |
| OEM-3-X | Injector 2 | injector_out | MS3PROMINI-A-11 | Injector out G | injector_out | single_source | |
| OEM-3-Y | Injector 3 | injector_out | MS3PROMINI-A-12 | Injector out H | injector_out | single_source | |
| OEM-3-Z | Injector 4 | injector_out | MS3PROMINI-A-5 | Injector out A | injector_out | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-1-B | SP-14V-1 | 0.85 | no route | ECU power +14V (main relay) | — | |
| W2 | OEM-3-M | SP-14V-1 | 0.85 | no route | ISC valve +14V feed | — | |
| W3 | SP-14V-1 | MS3PROMINI-A-1 | 0.85 | no route | 12V+ switched power in | — | |
| W4 | OEM-3-A | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W5 | OEM-3-B | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W6 | OEM-3-C | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W7 | SP-GND-1 | MS3PROMINI-A-22 | 0.85 | no route | Power ground | — | |
| W8 | SP-GND-1 | MS3PROMINI-A-23 | 0.85 | no route | Power ground | — | |
| W9 | OEM-3-F | SP-0V-1 | 0.5 | no route | Signal ground | — | |
| W10 | SP-0V-1 | MS3PROMINI-A-21 | 0.5 | no route | Sensor ground | — | |
| W11 | OEM-2-I | MS3PROMINI-A-2 | 0.5 | no route | +5V sensor supply | — | |
| W12 | OEM-2-J | MS3PROMINI-A-30 | 0.5 | no route | Crank position (CKP) | — | |
| W13 | OEM-2-H | MS3PROMINI-A-32 | 0.5 | no route | Cam position (CMP) | — | |
| W14 | OEM-3-G | MS3PROMINI-A-17 | 0.5 | no route | Ignition 1 (coils 1+4, wasted spark) | — | |
| W15 | OEM-3-H | MS3PROMINI-A-18 | 0.5 | no route | Ignition 2 (coils 2+3, wasted spark) | — | |
| W16 | OEM-3-W | MS3PROMINI-A-10 | 0.5 | no route | Injector 1 | — | |
| W17 | OEM-3-X | MS3PROMINI-A-11 | 0.5 | no route | Injector 2 | — | |
| W18 | OEM-3-Y | MS3PROMINI-A-12 | 0.5 | no route | Injector 3 | — | |
| W19 | OEM-3-Z | MS3PROMINI-A-5 | 0.5 | no route | Injector 4 | — | |
| W20 | OEM-1-I | MS3PROMINI-A-4 | 0.5 | no route | Condenser fan relay | — | |
| W21 | OEM-1-R | MS3PROMINI-A-3 | 0.5 | no route | Cooling fan relay | — | |
| W22 | OEM-1-S | MS3PROMINI-A-6 | 0.5 | no route | A/C clutch relay | — | |
| W23 | OEM-3-N | MS3PROMINI-A-7 | 0.5 | no route | Fuel pump relay | — | |
| W24 | OEM-3-O | MS3PROMINI-A-8 | 0.5 | no route | ISC valve low side | — | |
| W25 | OEM-1-E | MS3PROMINI-A-9 | 0.5 | no route | Malfunction indicator lamp (MIL) | — | |
| W26 | OEM-2-L | MS3PROMINI-A-13 | 0.5 | no route | Mass air flow (MAF) | — | |
| W27 | OEM-3-E | MS3PROMINI-A-28 | 0.5 | no route | Throttle position (TPS) | — | |
| W28 | OEM-2-C | MS3PROMINI-A-14 | 0.5 | no route | Front O2 signal | — | |
| W29 | OEM-3-J | MS3PROMINI-A-15 | 0.5 | no route | Rear O2 signal | — | |
| W30 | OEM-2-E | MS3PROMINI-A-26 | 0.5 | no route | Coolant temperature (ECT) | — | |
| W31 | OEM-2-B | MS3PROMINI-A-27 | 0.5 | no route | Intake air temperature (IAT) | — | |
| W32 | OEM-2-A | MS3PROMINI-A-16 | 0.5 | no route | Fuel tank pressure | — | |
| W33 | OEM-2-D | MS3PROMINI-A-34 | 0.5 | no route | Vehicle speed | — | |
| W34 | OEM-1-F | MS3PROMINI-A-29 | 0.5 | no route | Brake switch | — | |
| W35 | OEM-1-G | MS3PROMINI-A-35 | 0.5 | no route | Power steering pressure switch | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 174514-6 | TE | AMP Multilock .040/.070 hybrid 16-pin female harness plug (Miata NB1 ECU) | 1.000 | ea |
| connector | 174515-6 | TE | AMP Multilock .040/.070 hybrid 22-pin female harness plug (Miata NA/NB ECU) | 1.000 | ea |
| connector | 174516-6 | TE | AMP Multilock .040/.070 hybrid 26-pin female harness plug (Miata NA/NB ECU) | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (5)
| Severity | Code | Subject | Message |
|---|---|---|---|
| info | NET_FAMILY | OEM-1-E ↔ MS3PROMINI-A-9 | OEM-1-E "Malfunction indicator lamp (MIL)" [low_side_out] is wired to MS3PROMINI-A-9 "Injector out E" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-1-S ↔ MS3PROMINI-A-6 | OEM-1-S "A/C clutch relay" [low_side_out] is wired to MS3PROMINI-A-6 "Injector out B" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-3-N ↔ MS3PROMINI-A-7 | OEM-3-N "Fuel pump relay" [low_side_out] is wired to MS3PROMINI-A-7 "Injector out C" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-3-O ↔ MS3PROMINI-A-8 | OEM-3-O "ISC valve low side" [low_side_out] is wired to MS3PROMINI-A-8 "Injector out D" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | UNMAPPED | OEM | 19 optional OEM pins are not mapped: OEM-1-O Alternator control; OEM-1-P A/C request; OEM-1-Q Charge lamp; OEM-1-U Front O2 heater; OEM-1-V Neutral switch; OEM-2-F Knock sensor; OEM-2-K Tachometer output; OEM-2-M EGR valve; OEM-2-N EGR valve; OEM-2-O EGR valve; OEM-2-P EGR valve; OEM-3-I Clutch switch; OEM-3-K Fuel level; OEM-3-L Evap purge solenoid; OEM-3-Q VICS solenoid (intake butterflies); OEM-3-S EGR boost sensor; OEM-3-T EGR boost solenoid; OEM-3-U Canister drain cut valve (CDCV); OEM-3-V Rear O2 heater |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-1-A | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-06. Review every wire against both manuals before building. Not wired: - OEM-1 A: Constant +12V: AMP EFI MS3Pro Mini has no battery-constant input; not needed - OEM-2 F: Knock sensor: no free knock input on AMP EFI MS3Pro Mini - OEM-1 U: Front O2 heater: no free heater_low_side/low_side/ls_hs/hbridge on AMP EFI MS3Pro Mini - OEM-3 V: Rear O2 heater: no free heater_low_side/low_side/ls_hs/hbridge on AMP EFI MS3Pro Mini - OEM-1 O: Alternator control: no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-1 Q: Charge lamp: no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-2 M: EGR valve: no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-2 N: EGR valve: no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-2 O: EGR valve: no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-2 P: EGR valve: no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-3 L: Evap purge solenoid: no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-3 Q: VICS solenoid (intake butterflies): no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-3 T: EGR boost solenoid: no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-3 U: Canister drain cut valve (CDCV): no free low_side/ls_hs/injector/hbridge on AMP EFI MS3Pro Mini - OEM-2 K: Tachometer output: no free tacho/frequency_out/low_side/ls_hs on AMP EFI MS3Pro Mini - OEM-3 K: Fuel level: no free analog_0_5 on AMP EFI MS3Pro Mini - OEM-3 S: EGR boost sensor: no free analog_0_5 on AMP EFI MS3Pro Mini - OEM-1 P: A/C request: no free switch_in/frequency_in/analog_0_5 on AMP EFI MS3Pro Mini - OEM-1 V: Neutral switch: no free switch_in/frequency_in/analog_0_5 on AMP EFI MS3Pro Mini - OEM-3 I: Clutch switch: no free switch_in/frequency_in/analog_0_5 on AMP EFI MS3Pro Mini
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | AMP EFI: MS3Pro Mini manual (fw 1.6.1) pinout & output ratings | https://cdn.shopify.com/s/files/1/0960/0014/7754/files/MS3Pro_User_Manual_Firmware_1.6.1_Mini.pdf?v=1760643335 | archive | 2026-10-05 | bed7d8ae8408 |
| 4 | vendor_doc | Link G4X MX5NB1X install manual (NB1 1999-00) | https://linkecu.com/documentation/MX5XNB1.pdf | archive | 2026-10-05 | 2e36c91270cc |