RSX Type-S 2002-04 (K20A2) → MaxxECU MaxxECU MINI REV10+ (auto)
RSX Type-S 2002-04 (K20A2) — MaxxECU — MaxxECU MINI
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-08
Before you start
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 2: read the Findings page before cutting any wire |
| Size of the job | 40 wires · 8 connectors · 4 part lines |
| Tools | 715131-1 · wire strippers · multimeter · heat gun + heat-shrink |
| Terminals | 316836-1 |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-A-2 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-A-3 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | MAXXECUMINI-C1-H4 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-A-23 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-A-24 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-A-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-A-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-E-3 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | MAXXECUMINI-C1-G4 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-A-10 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-A-11 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-E-4 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | SP-0V-1 | MAXXECUMINI-C1-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | SP-0V-1 | MAXXECUMINI-C1-B3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | SP-0V-1 | MAXXECUMINI-C1-B4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | SP-0V-1 | MAXXECUMINI-C1-D4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-A-20 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-A-21 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-E-5 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | SP-5V1-1 | MAXXECUMINI-C1-E2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-A-7 | MAXXECUMINI-C1-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-A-30 | MAXXECUMINI-C1-F1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-A-29 | MAXXECUMINI-C1-F2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-A-28 | MAXXECUMINI-C1-F3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-A-27 | MAXXECUMINI-C1-F4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-B-5 | MAXXECUMINI-C1-G3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-B-4 | MAXXECUMINI-C1-H1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-B-3 | MAXXECUMINI-C1-H2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-B-2 | MAXXECUMINI-C1-H3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-E-7 | MAXXECUMINI-C1-G2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-B-6 | MAXXECUMINI-C1-G1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-E-1 | MAXXECUMINI-C1-E1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-E-18 | MAXXECUMINI-C1-D1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-A-19 | MAXXECUMINI-C1-C3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-A-15 | MAXXECUMINI-C1-D2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-E-2 | MAXXECUMINI-C1-C4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-B-8 | MAXXECUMINI-C1-C1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-B-17 | MAXXECUMINI-C1-C2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-A-18 | MAXXECUMINI-C1-B1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-B-10 | MAXXECUMINI-C1-B2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | MAXXECUMINI-C1-H4 | MAXXECUMINI-C1-A2 | open (OL) | +12 V supply must not touch sensor ground | |
| 2 | MAXXECUMINI-C1-H4 | MAXXECUMINI-C1-G4 | open (OL) | +12 V supply must not touch power ground | |
| 3 | MAXXECUMINI-C1-A2 | MAXXECUMINI-C1-E2 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 4 | MAXXECUMINI-C1-G4 | MAXXECUMINI-C1-E2 | open (OL) | power ground must not touch 5 V sensor reference | |
| 5 | MAXXECUMINI-C1-H4 | MAXXECUMINI-C1-E2 | open (OL) | +12 V supply must not touch 5 V sensor reference |
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
MAXXECUMINI-C1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A1 | TRIGGER | — | W21 | — | 0.5 | OEM-A-7 | — | — | — |
| A2 | TRIGGER GND | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| B1 | DIN 1 (Hall only) | — | W39 | — | 0.5 | OEM-A-18 | — | — | — |
| B2 | DIN 2 (Hall only) | — | W40 | — | 0.5 | OEM-B-10 | — | — | — |
| B3 | SENSOR GND | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| B4 | SENSOR GND | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| C1 | CLT | — | W37 | — | 0.5 | OEM-B-8 | — | — | — |
| C2 | IAT | — | W38 | — | 0.5 | OEM-B-17 | — | — | — |
| C3 | AIN 3 (0-5V) | — | W34 | — | 0.5 | OEM-A-19 | — | — | — |
| C4 | AIN 4 (0-5V) | — | W36 | — | 0.5 | OEM-E-2 | — | — | — |
| D1 | GPO 8/TACHO | — | W33 | — | 0.5 | OEM-E-18 | — | — | — |
| D2 | TPS | — | W35 | — | 0.5 | OEM-A-15 | — | — | — |
| D3 | GND Shield | — | — | — | — | — | — | — | — |
| D4 | SENSOR GND | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| E1 | GPO 3 | — | W32 | — | 0.5 | OEM-E-1 | — | — | — |
| E2 | +5V sensor supply | — | W20 | — | 0.5 | SP-5V1-1 | — | — | — |
| E3 | CAN L | — | — | — | — | — | — | — | — |
| E4 | CAN H | — | — | — | — | — | — | — | — |
| F1 | IGN 1 | — | W22 | — | 0.5 | OEM-A-30 | — | — | — |
| F2 | IGN 2 | — | W23 | — | 0.5 | OEM-A-29 | — | — | — |
| F3 | IGN 3 | — | W24 | — | 0.5 | OEM-A-28 | — | — | — |
| F4 | IGN 4 | — | W25 | — | 0.5 | OEM-A-27 | — | — | — |
| G1 | GPO 2 | — | W31 | — | 0.5 | OEM-B-6 | — | — | — |
| G2 | GPO 1 | — | W30 | — | 0.5 | OEM-E-7 | — | — | — |
| G3 | INJ 1 | — | W26 | — | 0.5 | OEM-B-5 | — | — | — |
| G4 | ENGINE GND | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| H1 | INJ 2 | — | W27 | — | 0.5 | OEM-B-4 | — | — | — |
| H2 | INJ 3 | — | W28 | — | 0.5 | OEM-B-3 | — | — | — |
| H3 | INJ 4 | — | W29 | — | 0.5 | OEM-B-2 | — | — | — |
| H4 | +12V (ECU power supply) | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
OEM-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | A/F sensor heater control (AFSHTC) | — | — | — | — | — | — | — | — |
| 2 | Ignition power 2 (IGP2) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 3 | Ignition power 1 (IGP1) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 4 | Power ground 2 (PG2) | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | Power ground 1 (PG1) | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | A/F sensor + (AFS+, wideband Ip) | — | — | — | — | — | — | — | — |
| 7 | Crank position sensor (CKP) | — | W21 | — | 0.5 | MAXXECUMINI-C1-A1 | — | — | — |
| 8 | — | — | — | — | — | — | — | — | — |
| 9 | Knock sensor (KS) | — | — | — | — | — | — | — | — |
| 10 | Sensor ground 2 (SG2) | — | W10 | — | 0.5 | SP-0V-1 | — | — | — |
| 11 | Sensor ground 1 (SG1) | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| 12 | Idle air control valve (IACV) | — | — | — | — | — | — | — | — |
| 13 | — | — | — | — | — | — | — | — | — |
| 14 | — | — | — | — | — | — | — | — | — |
| 15 | Throttle position sensor (TPS) | — | W35 | — | 0.5 | MAXXECUMINI-C1-D2 | — | — | — |
| 16 | A/F sensor - (AFS-, wideband Vs) | — | — | — | — | — | — | — | — |
| 17 | — | — | — | — | — | — | — | — | — |
| 18 | Vehicle speed sensor (VSS, M/T) | — | W39 | — | 0.5 | MAXXECUMINI-C1-B1 | — | — | — |
| 19 | Manifold absolute pressure (MAP) | — | W34 | — | 0.5 | MAXXECUMINI-C1-C3 | — | — | — |
| 20 | Sensor 5V supply 2 (VCC2) | — | W17 | — | 0.5 | SP-5V1-1 | — | — | — |
| 21 | Sensor 5V supply 1 (VCC1) | — | W18 | — | 0.5 | SP-5V1-1 | — | — | — |
| 22 | A/F sensor heater supply (AFSHTC+) | — | — | — | — | — | — | — | — |
| 23 | Logic ground 2 (LG2) | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| 24 | Logic ground 1 (LG1) | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 25 | Camshaft position A (CMP A) | — | — | — | — | — | — | — | — |
| 26 | Camshaft position B (CMP B) | — | — | — | — | — | — | — | — |
| 27 | Ignition coil 4 (IGPLS4) | — | W25 | — | 0.5 | MAXXECUMINI-C1-F4 | — | — | — |
| 28 | Ignition coil 3 (IGPLS3) | — | W24 | — | 0.5 | MAXXECUMINI-C1-F3 | — | — | — |
| 29 | Ignition coil 2 (IGPLS2) | — | W23 | — | 0.5 | MAXXECUMINI-C1-F2 | — | — | — |
| 30 | Ignition coil 1 (IGPLS1) | — | W22 | — | 0.5 | MAXXECUMINI-C1-F1 | — | — | — |
| 31 | — | — | — | — | — | — | — | — | — |
OEM-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | VTC oil control solenoid (+) | — | — | — | — | — | — | — | — |
| 2 | Injector 4 (INJ4) | — | W29 | — | 0.5 | MAXXECUMINI-C1-H3 | — | — | — |
| 3 | Injector 3 (INJ3) | — | W28 | — | 0.5 | MAXXECUMINI-C1-H2 | — | — | — |
| 4 | Injector 2 (INJ2) | — | W27 | — | 0.5 | MAXXECUMINI-C1-H1 | — | — | — |
| 5 | Injector 1 (INJ1) | — | W26 | — | 0.5 | MAXXECUMINI-C1-G3 | — | — | — |
| 6 | Radiator fan control (FANC) | — | W31 | — | 0.5 | MAXXECUMINI-C1-G1 | — | — | — |
| 7 | Reverse lockout solenoid (RVS, Type-S) | — | — | — | — | — | — | — | — |
| 8 | Coolant temp sensor (ECT) | — | W37 | — | 0.5 | MAXXECUMINI-C1-C1 | — | — | — |
| 9 | VTEC oil pressure switch (VTPSW) | — | — | — | — | — | — | — | — |
| 10 | Alternator L signal (ALTL) | — | W40 | — | 0.5 | MAXXECUMINI-C1-B2 | — | — | — |
| 11 | — | — | — | — | — | — | — | — | — |
| 12 | — | — | — | — | — | — | — | — | — |
| 13 | Alternator FR signal (ALTF) | — | — | — | — | — | — | — | — |
| 14 | — | — | — | — | — | — | — | — | — |
| 15 | VTEC solenoid (VTS) | — | — | — | — | — | — | — | — |
| 16 | — | — | — | — | — | — | — | — | — |
| 17 | Intake air temp sensor (IAT) | — | W38 | — | 0.5 | MAXXECUMINI-C1-C2 | — | — | — |
| 18 | Alternator control (ALTC) | — | — | — | — | — | — | — | — |
| 19 | — | — | — | — | — | — | — | — | — |
| 20 | — | — | — | — | — | — | — | — | — |
| 21 | Evap canister purge valve (PCS) | — | — | — | — | — | — | — | — |
| 22 | — | — | — | — | — | — | — | — | — |
| 23 | VTC oil control solenoid (-) | — | — | — | — | — | — | — | — |
| 24 | — | — | — | — | — | — | — | — | — |
OEM-E
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Immobilizer fuel pump relay (IMO FPR) | — | W32 | — | 0.5 | MAXXECUMINI-C1-E1 | — | — | — |
| 2 | Secondary heated O2 sensor (SHO2S) | — | W36 | — | 0.5 | MAXXECUMINI-C1-C4 | — | — | — |
| 3 | Logic ground 3 (LG3) | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 4 | Sensor ground 3 (SG3) | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| 5 | Sensor 5V supply 3 (VCC3) | — | W19 | — | 0.5 | SP-5V1-1 | — | — | — |
| 6 | Secondary O2 heater control (SO2SHTC) | — | — | — | — | — | — | — | — |
| 7 | Main relay control (MRLY) | — | W30 | — | 0.5 | MAXXECUMINI-C1-G2 | — | — | — |
| 8 | A/F sensor heater relay control (AFSHTCR) | — | — | — | — | — | — | — | — |
| 9 | Ignition switch signal (IG1) | — | — | — | — | — | — | — | — |
| 10 | — | — | — | — | — | — | — | — | — |
| 11 | — | — | — | — | — | — | — | — | — |
| 12 | — | — | — | — | — | — | — | — | — |
| 13 | — | — | — | — | — | — | — | — | — |
| 14 | Fuel tank pressure sensor (FTP) | — | — | — | — | — | — | — | — |
| 15 | Electrical load detector (ELD) | — | — | — | — | — | — | — | — |
| 16 | Power steering pressure switch (PSPSW) | — | — | — | — | — | — | — | — |
| 17 | — | — | — | — | — | — | — | — | — |
| 18 | A/C clutch relay (ACC) | — | W33 | — | 0.5 | MAXXECUMINI-C1-D1 | — | — | — |
| 19 | — | — | — | — | — | — | — | — | — |
| 20 | Brake switch / interlock (2WBS) | — | — | — | — | — | — | — | — |
| 21 | Evap vent shut valve (VSV) | — | — | — | — | — | — | — | — |
| 22 | Brake switch (BKSW) | — | — | — | — | — | — | — | — |
| 23 | K-line (diagnostic) | — | — | — | — | — | — | — | — |
| 24 | Multiplex communication (SEFMJ) | — | — | — | — | — | — | — | — |
| 25 | — | — | — | — | — | — | — | — | — |
| 26 | Engine speed pulse / tacho (NEP) | — | — | — | — | — | — | — | — |
| 27 | Immobilizer code (IMOCD) | — | — | — | — | — | — | — | — |
| 28 | — | — | — | — | — | — | — | — | — |
| 29 | Service check signal (SCS) | — | — | — | — | — | — | — | — |
| 30 | Write enable signal (WEN) | — | — | — | — | — | — | — | — |
| 31 | Malfunction indicator lamp (MIL) | — | — | — | — | — | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W15 | — | 0.5 | MAXXECUMINI-C1-B4 | — | — | — |
| 1 | — | — | W10 | — | 0.5 | OEM-A-10 | — | — | — |
| 1 | — | — | W11 | — | 0.5 | OEM-A-11 | — | — | — |
| 1 | — | — | W12 | — | 0.5 | OEM-E-4 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | MAXXECUMINI-C1-A2 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | MAXXECUMINI-C1-B3 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | MAXXECUMINI-C1-D4 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-A-2 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-A-3 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | MAXXECUMINI-C1-H4 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W17 | — | 0.5 | OEM-A-20 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | OEM-A-21 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | OEM-E-5 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | MAXXECUMINI-C1-E2 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W4 | — | 0.85 | OEM-A-23 | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-A-24 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-A-4 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-A-5 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | OEM-E-3 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | MAXXECUMINI-C1-G4 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-A-1 | A/F sensor heater control (AFSHTC) | low_side_out | — | — | — | single_source | |
| OEM-A-10 | Sensor ground 2 (SG2) | sensor_ground | MAXXECUMINI-C1-A2 + MAXXECUMINI-C1-B3 + MAXXECUMINI-C1-B4 + MAXXECUMINI-C1-D4 | TRIGGER GND + SENSOR GND + SENSOR GND + SENSOR GND | sensor_ground | corroborated | |
| OEM-A-11 | Sensor ground 1 (SG1) | sensor_ground | MAXXECUMINI-C1-A2 + MAXXECUMINI-C1-B3 + MAXXECUMINI-C1-B4 + MAXXECUMINI-C1-D4 | TRIGGER GND + SENSOR GND + SENSOR GND + SENSOR GND | sensor_ground | corroborated | |
| OEM-A-12 | Idle air control valve (IACV) | low_side_out | — | — | — | corroborated | |
| OEM-A-15 | Throttle position sensor (TPS) | analog_in | MAXXECUMINI-C1-D2 | TPS | analog_in | corroborated | |
| OEM-A-16 | A/F sensor - (AFS-, wideband Vs) | wb_vs | — | — | — | single_source | |
| OEM-A-18 | Vehicle speed sensor (VSS, M/T) | digital_in | MAXXECUMINI-C1-B1 | DIN 1 (Hall only) | digital_in | corroborated | |
| OEM-A-19 | Manifold absolute pressure (MAP) | analog_in | MAXXECUMINI-C1-C3 | AIN 3 (0-5V) | analog_in | corroborated | |
| OEM-A-2 | Ignition power 2 (IGP2) | power_in | MAXXECUMINI-C1-H4 | +12V (ECU power supply) | power_in | corroborated | |
| OEM-A-20 | Sensor 5V supply 2 (VCC2) | vref | MAXXECUMINI-C1-E2 | +5V sensor supply | vref | corroborated | |
| OEM-A-21 | Sensor 5V supply 1 (VCC1) | vref | MAXXECUMINI-C1-E2 | +5V sensor supply | vref | corroborated | |
| OEM-A-22 | A/F sensor heater supply (AFSHTC+) | power_out | — | — | — | single_source | |
| OEM-A-23 | Logic ground 2 (LG2) | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | corroborated | |
| OEM-A-24 | Logic ground 1 (LG1) | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | corroborated | |
| OEM-A-25 | Camshaft position A (CMP A) | trigger_in | — | — | — | single_source | |
| OEM-A-26 | Camshaft position B (CMP B) | trigger_in | — | — | — | single_source | |
| OEM-A-27 | Ignition coil 4 (IGPLS4) | ignition_out | MAXXECUMINI-C1-F4 | IGN 4 | ignition_out | corroborated | |
| OEM-A-28 | Ignition coil 3 (IGPLS3) | ignition_out | MAXXECUMINI-C1-F3 | IGN 3 | ignition_out | corroborated | |
| OEM-A-29 | Ignition coil 2 (IGPLS2) | ignition_out | MAXXECUMINI-C1-F2 | IGN 2 | ignition_out | corroborated | |
| OEM-A-3 | Ignition power 1 (IGP1) | power_in | MAXXECUMINI-C1-H4 | +12V (ECU power supply) | power_in | corroborated | |
| OEM-A-30 | Ignition coil 1 (IGPLS1) | ignition_out | MAXXECUMINI-C1-F1 | IGN 1 | ignition_out | corroborated | |
| OEM-A-4 | Power ground 2 (PG2) | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | corroborated | |
| OEM-A-5 | Power ground 1 (PG1) | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | corroborated | |
| OEM-A-6 | A/F sensor + (AFS+, wideband Ip) | wb_ip | — | — | — | single_source | |
| OEM-A-7 | Crank position sensor (CKP) | trigger_in | MAXXECUMINI-C1-A1 | TRIGGER | trigger_in | corroborated | |
| OEM-A-9 | Knock sensor (KS) | knock_in | — | — | — | corroborated | |
| OEM-B-1 | VTC oil control solenoid (+) | low_side_out | — | — | — | corroborated | |
| OEM-B-10 | Alternator L signal (ALTL) | digital_in | MAXXECUMINI-C1-B2 | DIN 2 (Hall only) | digital_in | single_source | |
| OEM-B-13 | Alternator FR signal (ALTF) | analog_in | — | — | — | single_source | |
| OEM-B-15 | VTEC solenoid (VTS) | low_side_out | — | — | — | single_source | |
| OEM-B-17 | Intake air temp sensor (IAT) | temp_in | MAXXECUMINI-C1-C2 | IAT | temp_in | corroborated | |
| OEM-B-18 | Alternator control (ALTC) | low_side_out | — | — | — | corroborated | |
| OEM-B-2 | Injector 4 (INJ4) | injector_out | MAXXECUMINI-C1-H3 | INJ 4 | injector_out | corroborated | |
| OEM-B-21 | Evap canister purge valve (PCS) | low_side_out | — | — | — | corroborated | |
| OEM-B-23 | VTC oil control solenoid (-) | low_side_out | — | — | — | corroborated | |
| OEM-B-3 | Injector 3 (INJ3) | injector_out | MAXXECUMINI-C1-H2 | INJ 3 | injector_out | corroborated | |
| OEM-B-4 | Injector 2 (INJ2) | injector_out | MAXXECUMINI-C1-H1 | INJ 2 | injector_out | corroborated | |
| OEM-B-5 | Injector 1 (INJ1) | injector_out | MAXXECUMINI-C1-G3 | INJ 1 | injector_out | corroborated | |
| OEM-B-6 | Radiator fan control (FANC) | low_side_out | MAXXECUMINI-C1-G1 | GPO 2 | low_side_out | corroborated | |
| OEM-B-7 | Reverse lockout solenoid (RVS, Type-S) | low_side_out | — | — | — | corroborated | |
| OEM-B-8 | Coolant temp sensor (ECT) | temp_in | MAXXECUMINI-C1-C1 | CLT | temp_in | corroborated | |
| OEM-B-9 | VTEC oil pressure switch (VTPSW) | digital_in | — | — | — | corroborated | |
| OEM-E-1 | Immobilizer fuel pump relay (IMO FPR) | low_side_out | MAXXECUMINI-C1-E1 | GPO 3 | low_side_out | corroborated | |
| OEM-E-14 | Fuel tank pressure sensor (FTP) | analog_in | — | — | — | corroborated | |
| OEM-E-15 | Electrical load detector (ELD) | analog_in | — | — | — | corroborated | |
| OEM-E-16 | Power steering pressure switch (PSPSW) | digital_in | — | — | — | corroborated | |
| OEM-E-18 | A/C clutch relay (ACC) | low_side_out | MAXXECUMINI-C1-D1 | GPO 8/TACHO | low_side_out | corroborated | |
| OEM-E-2 | Secondary heated O2 sensor (SHO2S) | lambda_nb_in | MAXXECUMINI-C1-C4 | AIN 4 (0-5V) | analog_in | corroborated | |
| OEM-E-20 | Brake switch / interlock (2WBS) | digital_in | — | — | — | single_source | |
| OEM-E-21 | Evap vent shut valve (VSV) | low_side_out | — | — | — | corroborated | |
| OEM-E-22 | Brake switch (BKSW) | digital_in | — | — | — | corroborated | |
| OEM-E-23 | K-line (diagnostic) | serial | — | — | — | single_source | |
| OEM-E-24 | Multiplex communication (SEFMJ) | serial | — | — | — | corroborated | |
| OEM-E-26 | Engine speed pulse / tacho (NEP) | tacho_out | — | — | — | corroborated | |
| OEM-E-27 | Immobilizer code (IMOCD) | — | — | — | — | single_source | |
| OEM-E-29 | Service check signal (SCS) | — | — | — | — | single_source | |
| OEM-E-3 | Logic ground 3 (LG3) | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | corroborated | |
| OEM-E-30 | Write enable signal (WEN) | — | — | — | — | single_source | |
| OEM-E-31 | Malfunction indicator lamp (MIL) | low_side_out | — | — | — | corroborated | |
| OEM-E-4 | Sensor ground 3 (SG3) | sensor_ground | MAXXECUMINI-C1-A2 + MAXXECUMINI-C1-B3 + MAXXECUMINI-C1-B4 + MAXXECUMINI-C1-D4 | TRIGGER GND + SENSOR GND + SENSOR GND + SENSOR GND | sensor_ground | corroborated | |
| OEM-E-5 | Sensor 5V supply 3 (VCC3) | vref | MAXXECUMINI-C1-E2 | +5V sensor supply | vref | corroborated | |
| OEM-E-6 | Secondary O2 heater control (SO2SHTC) | low_side_out | — | — | — | corroborated | |
| OEM-E-7 | Main relay control (MRLY) | low_side_out | MAXXECUMINI-C1-G2 | GPO 1 | low_side_out | corroborated | |
| OEM-E-8 | A/F sensor heater relay control (AFSHTCR) | low_side_out | — | — | — | corroborated | |
| OEM-E-9 | Ignition switch signal (IG1) | digital_in | — | — | — | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-A-2 | SP-14V-1 | 0.85 | no route | Ignition power 2 (IGP2) | — | |
| W2 | OEM-A-3 | SP-14V-1 | 0.85 | no route | Ignition power 1 (IGP1) | — | |
| W3 | SP-14V-1 | MAXXECUMINI-C1-H4 | 0.85 | no route | +12V (ECU power supply) | — | |
| W4 | OEM-A-23 | SP-GND-1 | 0.85 | no route | Logic ground 2 (LG2) | — | |
| W5 | OEM-A-24 | SP-GND-1 | 0.85 | no route | Logic ground 1 (LG1) | — | |
| W6 | OEM-A-4 | SP-GND-1 | 0.85 | no route | Power ground 2 (PG2) | — | |
| W7 | OEM-A-5 | SP-GND-1 | 0.85 | no route | Power ground 1 (PG1) | — | |
| W8 | OEM-E-3 | SP-GND-1 | 0.85 | no route | Logic ground 3 (LG3) | — | |
| W9 | SP-GND-1 | MAXXECUMINI-C1-G4 | 0.85 | no route | ENGINE GND | — | |
| W10 | OEM-A-10 | SP-0V-1 | 0.5 | no route | Sensor ground 2 (SG2) | — | |
| W11 | OEM-A-11 | SP-0V-1 | 0.5 | no route | Sensor ground 1 (SG1) | — | |
| W12 | OEM-E-4 | SP-0V-1 | 0.5 | no route | Sensor ground 3 (SG3) | — | |
| W13 | SP-0V-1 | MAXXECUMINI-C1-A2 | 0.5 | no route | TRIGGER GND | — | |
| W14 | SP-0V-1 | MAXXECUMINI-C1-B3 | 0.5 | no route | SENSOR GND | — | |
| W15 | SP-0V-1 | MAXXECUMINI-C1-B4 | 0.5 | no route | SENSOR GND | — | |
| W16 | SP-0V-1 | MAXXECUMINI-C1-D4 | 0.5 | no route | SENSOR GND | — | |
| W17 | OEM-A-20 | SP-5V1-1 | 0.5 | no route | Sensor 5V supply 2 (VCC2) | — | |
| W18 | OEM-A-21 | SP-5V1-1 | 0.5 | no route | Sensor 5V supply 1 (VCC1) | — | |
| W19 | OEM-E-5 | SP-5V1-1 | 0.5 | no route | Sensor 5V supply 3 (VCC3) | — | |
| W20 | SP-5V1-1 | MAXXECUMINI-C1-E2 | 0.5 | no route | +5V sensor supply | — | |
| W21 | OEM-A-7 | MAXXECUMINI-C1-A1 | 0.5 | no route | Crank position sensor (CKP) | — | |
| W22 | OEM-A-30 | MAXXECUMINI-C1-F1 | 0.5 | no route | Ignition coil 1 (IGPLS1) | — | |
| W23 | OEM-A-29 | MAXXECUMINI-C1-F2 | 0.5 | no route | Ignition coil 2 (IGPLS2) | — | |
| W24 | OEM-A-28 | MAXXECUMINI-C1-F3 | 0.5 | no route | Ignition coil 3 (IGPLS3) | — | |
| W25 | OEM-A-27 | MAXXECUMINI-C1-F4 | 0.5 | no route | Ignition coil 4 (IGPLS4) | — | |
| W26 | OEM-B-5 | MAXXECUMINI-C1-G3 | 0.5 | no route | Injector 1 (INJ1) | — | |
| W27 | OEM-B-4 | MAXXECUMINI-C1-H1 | 0.5 | no route | Injector 2 (INJ2) | — | |
| W28 | OEM-B-3 | MAXXECUMINI-C1-H2 | 0.5 | no route | Injector 3 (INJ3) | — | |
| W29 | OEM-B-2 | MAXXECUMINI-C1-H3 | 0.5 | no route | Injector 4 (INJ4) | — | |
| W30 | OEM-E-7 | MAXXECUMINI-C1-G2 | 0.5 | no route | Main relay control (MRLY) | — | |
| W31 | OEM-B-6 | MAXXECUMINI-C1-G1 | 0.5 | no route | Radiator fan control (FANC) | — | |
| W32 | OEM-E-1 | MAXXECUMINI-C1-E1 | 0.5 | no route | Immobilizer fuel pump relay (IMO FPR) | — | |
| W33 | OEM-E-18 | MAXXECUMINI-C1-D1 | 0.5 | no route | A/C clutch relay (ACC) | — | |
| W34 | OEM-A-19 | MAXXECUMINI-C1-C3 | 0.5 | no route | Manifold absolute pressure (MAP) | — | |
| W35 | OEM-A-15 | MAXXECUMINI-C1-D2 | 0.5 | no route | Throttle position sensor (TPS) | — | |
| W36 | OEM-E-2 | MAXXECUMINI-C1-C4 | 0.5 | no route | Secondary heated O2 sensor (SHO2S) | — | |
| W37 | OEM-B-8 | MAXXECUMINI-C1-C1 | 0.5 | no route | Coolant temp sensor (ECT) | — | |
| W38 | OEM-B-17 | MAXXECUMINI-C1-C2 | 0.5 | no route | Intake air temp sensor (IAT) | — | |
| W39 | OEM-A-18 | MAXXECUMINI-C1-B1 | 0.5 | no route | Vehicle speed sensor (VSS, M/T) | — | |
| W40 | OEM-B-10 | MAXXECUMINI-C1-B2 | 0.5 | no route | Alternator L signal (ALTL) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 1318682-6 | TE | K-series ECU harness plug A (040-3 HD plug assy, 31P) | 1.000 | ea |
| connector | 353029-1 | TE | K-series ECU harness plug B (040 H/D-3 plug HSG assy, 24P) | 1.000 | ea |
| connector | 353826-1 | TE | K-series ECU harness plug E (040 HD 31P plug HSG assy-B, 31P) | 1.000 | ea |
| terminal | 316836-1 | TE | Multilock 040 III HD socket, tin, 22–18 AWG (0.3–0.85 mm²) | 33.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (11)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | REQUIRED_UNMAPPED | OEM-A-25 | Required OEM function "Camshaft position A (CMP A)" (trigger_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-A-26 | Required OEM function "Camshaft position B (CMP B)" (trigger_in) is not connected to the new ECU. |
| warn | DATASET_GAP | RSX ECU A | 5 of 31 cavities on RSX ECU A have no pin data (8,13,14,17,31). Anything there is invisible to these checks. |
| warn | DATASET_GAP | RSX ECU B | 8 of 24 cavities on RSX ECU B have no pin data (11,12,14,16,19,20,22,24). Anything there is invisible to these checks. |
| warn | DATASET_GAP | RSX ECU E | 8 of 31 cavities on RSX ECU E have no pin data (10,11,12,13,17,19,25,28). Anything there is invisible to these checks. |
| warn | LOAD_UNKNOWN | MAXXECUMINI-C1-D1 | MAXXECUMINI-C1-D1 "GPO 8/TACHO" drives OEM-E-18 A/C clutch relay (ACC) (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | MAXXECUMINI-C1-E1 | MAXXECUMINI-C1-E1 "GPO 3" drives OEM-E-1 Immobilizer fuel pump relay (IMO FPR) (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | MAXXECUMINI-C1-G1 | MAXXECUMINI-C1-G1 "GPO 2" drives OEM-B-6 Radiator fan control (FANC) (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | MAXXECUMINI-C1-G2 | MAXXECUMINI-C1-G2 "GPO 1" drives OEM-E-7 Main relay control (MRLY) (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | SUPPLY_GROUP | MAXXECUMINI-C1-E2 + OEM-A-20 + OEM-A-21 + OEM-E-5 + SP-5V1-1 | Supplies meant to stay independent share one net: OEM-A-20 [k_vcc2], OEM-A-21 [k_vcc1], OEM-E-5 [k_vcc3]. The new ECU has no free 5 V reference, so they share one: normal on a standalone, but a short on any of these sensors drops them all. |
| info | UNMAPPED | OEM | 30 optional OEM pins are not mapped: OEM-A-1 A/F sensor heater control (AFSHTC); OEM-A-12 Idle air control valve (IACV); OEM-A-16 A/F sensor - (AFS-, wideband Vs); OEM-A-22 A/F sensor heater supply (AFSHTC+); OEM-A-6 A/F sensor + (AFS+, wideband Ip); OEM-A-9 Knock sensor (KS); OEM-B-1 VTC oil control solenoid (+); OEM-B-13 Alternator FR signal (ALTF); OEM-B-15 VTEC solenoid (VTS); OEM-B-18 Alternator control (ALTC); OEM-B-21 Evap canister purge valve (PCS); OEM-B-23 VTC oil control solenoid (-); OEM-B-7 Reverse lockout solenoid (RVS, Type-S); OEM-B-9 VTEC oil pressure switch (VTPSW); OEM-E-14 Fuel tank pressure sensor (FTP); OEM-E-15 Electrical load detector (ELD); OEM-E-16 Power steering pressure switch (PSPSW); OEM-E-20 Brake switch / interlock (2WBS); OEM-E-21 Evap vent shut valve (VSV); OEM-E-22 Brake switch (BKSW); OEM-E-23 K-line (diagnostic); OEM-E-24 Multiplex communication (SEFMJ); OEM-E-26 Engine speed pulse / tacho (NEP); OEM-E-27 Immobilizer code (IMOCD); OEM-E-29 Service check signal (SCS); OEM-E-30 Write enable signal (WEN); OEM-E-31 Malfunction indicator lamp (MIL); OEM-E-6 Secondary O2 heater control (SO2SHTC); OEM-E-8 A/F sensor heater relay control (AFSHTCR); OEM-E-9 Ignition switch signal (IG1) |
Accepted (0)
| Code | Subject | Reason | By |
|---|
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-06. Review every wire against both manuals before building. Open items: - OEM-A 25: Camshaft position A (CMP A): no free cam_hall/cam_vr/frequency_in input on MaxxECU MaxxECU MINI - OEM-A 26: Camshaft position B (CMP B): no free cam_hall/cam_vr/frequency_in input on MaxxECU MaxxECU MINI Not wired: - OEM-A 9: Knock sensor (KS): no free knock input on MaxxECU MaxxECU MINI - OEM-E 9: Ignition switch signal (IG1): key-on 12 V sense — optional in a swap (the main relay is energized from keyed 12 V, not from this pin); MaxxECU MaxxECU MINI has no dedicated key-on input - OEM-E 8: A/F sensor heater relay control (AFSHTCR): no free relay_control/low_side/ls_hs/injector/hbridge rated ≥ 0.2 A on MaxxECU MaxxECU MINI - OEM-E 6: Secondary O2 heater control (SO2SHTC): no free heater_low_side/low_side/ls_hs/hbridge on MaxxECU MaxxECU MINI - OEM-A 1: A/F sensor heater control (AFSHTC): no free heater_low_side/low_side/ls_hs/hbridge on MaxxECU MaxxECU MINI - OEM-A 12: Idle air control valve (IACV): no free low_side/ls_hs/injector/hbridge rated ≥ 1.0 A on MaxxECU MaxxECU MINI - OEM-B 15: VTEC solenoid (VTS): no free low_side/ls_hs/injector/hbridge rated ≥ 1.0 A on MaxxECU MaxxECU MINI - OEM-B 1: VTC oil control solenoid (+): no free low_side/ls_hs/injector/hbridge on MaxxECU MaxxECU MINI - OEM-B 18: Alternator control (ALTC): no free low_side/ls_hs/injector/hbridge on MaxxECU MaxxECU MINI - OEM-B 21: Evap canister purge valve (PCS): no free low_side/ls_hs/injector/hbridge on MaxxECU MaxxECU MINI - OEM-B 23: VTC oil control solenoid (-): no free low_side/ls_hs/injector/hbridge on MaxxECU MaxxECU MINI - OEM-B 7: Reverse lockout solenoid (RVS, Type-S): no free low_side/ls_hs/injector/hbridge on MaxxECU MaxxECU MINI - OEM-E 21: Evap vent shut valve (VSV): no free low_side/ls_hs/injector/hbridge on MaxxECU MaxxECU MINI - OEM-E 31: Malfunction indicator lamp (MIL): no free low_side/ls_hs/injector/hbridge on MaxxECU MaxxECU MINI - OEM-E 26: Engine speed pulse / tacho (NEP): no free tacho/frequency_out/low_side/ls_hs on MaxxECU MaxxECU MINI - OEM-A 6: A/F sensor + (AFS+, wideband Ip): no free wb_ip on MaxxECU MaxxECU MINI - OEM-A 16: A/F sensor - (AFS-, wideband Vs): no free wb_vs on MaxxECU MaxxECU MINI - OEM-A 22: A/F sensor heater supply (AFSHTC+): no free heater_feed on MaxxECU MaxxECU MINI - OEM-B 13: Alternator FR signal (ALTF): no free analog_0_5 on MaxxECU MaxxECU MINI - OEM-E 14: Fuel tank pressure sensor (FTP): no free analog_0_5 on MaxxECU MaxxECU MINI - OEM-E 15: Electrical load detector (ELD): no free analog_0_5 on MaxxECU MaxxECU MINI - OEM-B 9: VTEC oil pressure switch (VTPSW): no free switch_in/frequency_in/analog_0_5 on MaxxECU MaxxECU MINI - OEM-E 16: Power steering pressure switch (PSPSW): no free switch_in/frequency_in/analog_0_5 on MaxxECU MaxxECU MINI - OEM-E 20: Brake switch / interlock (2WBS): no free switch_in/frequency_in/analog_0_5 on MaxxECU MaxxECU MINI - OEM-E 22: Brake switch (BKSW): no free switch_in/frequency_in/analog_0_5 on MaxxECU MaxxECU MINI - OEM-E 23: K-line (diagnostic): no free k_line on MaxxECU MaxxECU MINI - OEM-E 24: Multiplex communication (SEFMJ): no free k_line on MaxxECU MaxxECU MINI - OEM-E 27: Immobilizer code (IMOCD): not classified in the library; wire by hand - OEM-E 29: Service check signal (SCS): not classified in the library; wire by hand - OEM-E 30: Write enable signal (WEN): not classified in the library; wire by hand
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | Link: CIVICLink K20X (HC20X) DC5 installation manual | https://linkecu.com/documentation/237-4000%20DC5.pdf | archive | 2026-10-05 | 8a1a71301571 |
| 4 | vendor_doc | MaxxECU GEN1 pinout (MINI / STREET / SPORT / V1 / RACE / PRO) | http://www.maxxecu.com/webhelp/wirings-maxxecu_pinout.html | archive | 2026-10-05 | 2e37b6814690 |
| 3 | forum | FFS TechNet: K-series 02-06 RSX ECU pin diagram (Helm) | https://ff-squad.com/technet2/k-series-02-06-rsx-ecu-pin-diagram/ | archive | 2026-10-05 | b2b85002666e |