MX-5 Miata NA6 1990-93 (B6-ZE, 1.6) → ECUMASTER EMU PRO 16 (auto)
MX-5 Miata NA6 1990-93 (B6-ZE, 1.6) — ECUMASTER — EMU PRO 16
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-09
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
Install modifications
Steps on the car itself, outside the harness. Every harness for this car inherits them.
- Cut the sensor-ground-to-chassis wirerequired
Cut the wire in the engine bay that ties the ECU sensor/signal ground (2C/2D, BLK/LT GRN) to chassis ground, so the standalone gets a clean sensor-ground reference. After cutting, verify with a meter: sensor ground ↔ chassis ground reads open (OL) unless the standalone manual says otherwise.
Why: The stock loom bonds sensor ground to chassis ground; a standalone ECU needs its sensor ground isolated from the noisy chassis/power ground, otherwise sensor readings are noisy or wrong.
Where: Engine-bay ground joint near the ECU (1991 EWD Fig.2 shows the sensor-ground run and its joint connector).
Correction reported by Justin Barrera
Unverified — reported by Justin Barrera (Motorsport Wiring Alliance), not yet sourced.
- Bypass the airflow-meter pump switchrecommended
The stock pump is run by the flapper airflow meter's pump-switch contact through the circuit-opening relay, not by the ECU. The standalone harness adds ECU control of the pump relay (ignition-switched, fused); remove/bypass the AFM pump switch so the two do not fight.
Why: There is no stock fuel-pump output at the ECU, so the standalone provides it. Leaving the AFM switch in place leaves a second, unswitched pump path.
Where: Airflow meter connector (pump-switch contact) and circuit-opening relay.
Correction reported by Justin Barrera
Source: 1991 Mazda Miata wiring diagrams (Mitchell reproduction, mellens.net community mirror)
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 1: read the Findings page before cutting any wire |
| Size of the job | 37 wires · 9 connectors · 7 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Terminals | 3-1447221-4 |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-1-B | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | SP-14V-1 | EMUPRO16-B-14 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | EMUPRO16-B-8 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-2-A | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-2-B | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | SP-GND-1 | EMUPRO16-A-11 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | SP-GND-1 | EMUPRO16-A-17 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | SP-GND-1 | EMUPRO16-A-19 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | EMUPRO16-B-19 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | SP-GND-1 | EMUPRO16-C-30 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | SP-GND-1 | EMUPRO16-D-18 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-2-C | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-2-D | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | SP-0V-1 | EMUPRO16-A-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | SP-0V-1 | EMUPRO16-B-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | SP-0V-1 | EMUPRO16-C-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | SP-0V-1 | EMUPRO16-D-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-2-K | EMUPRO16-A-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-2-E | EMUPRO16-A-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-1-G | EMUPRO16-A-30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-1-H | EMUPRO16-A-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-2-U | EMUPRO16-A-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-2-V | EMUPRO16-A-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-2-Y | EMUPRO16-A-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-2-Z | EMUPRO16-A-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-1-E | EMUPRO16-B-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-2-I | EMUPRO16-B-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-2-O | EMUPRO16-C-31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-2-N | EMUPRO16-C-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-2-Q | EMUPRO16-C-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-2-P | EMUPRO16-C-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-1-C | EMUPRO16-A-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-1-N | EMUPRO16-A-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-1-P | EMUPRO16-A-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-1-Q | EMUPRO16-A-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-1-V | EMUPRO16-A-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-2-L | EMUPRO16-A-23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Pre-power install steps (make these cuts/modifications on the car first, then verify the checks below): Cut the sensor-ground-to-chassis wire.
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | EMUPRO16-B-14 | EMUPRO16-A-11 | open (OL) | +12 V supply must not touch power ground | |
| 2 | EMUPRO16-B-14 | EMUPRO16-A-20 | open (OL) | +12 V supply must not touch sensor ground | |
| 3 | EMUPRO16-A-11 | EMUPRO16-A-12 | open (OL) | power ground must not touch 5 V sensor reference | |
| 4 | EMUPRO16-A-20 | EMUPRO16-A-12 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 5 | EMUPRO16-B-14 | EMUPRO16-A-12 | open (OL) | +12 V supply must not touch 5 V sensor reference |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
EMUPRO16-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Ignition 8 | — | — | — | — | — | — | — | — |
| 2 | Injector 1 | — | W22 | — | 0.5 | OEM-2-U | — | — | — |
| 3 | Injector 2 | — | W23 | — | 0.5 | OEM-2-V | — | — | — |
| 4 | Injector 3 | — | W24 | — | 0.5 | OEM-2-Y | — | — | — |
| 5 | Injector 4 | — | W25 | — | 0.5 | OEM-2-Z | — | — | — |
| 6 | Injector 5 | — | — | — | — | — | — | — | — |
| 7 | Injector 6 | — | — | — | — | — | — | — | — |
| 8 | Injector 7 | — | — | — | — | — | — | — | — |
| 9 | Injector 8 | — | — | — | — | — | — | — | — |
| 10 | Ignition 7 | — | — | — | — | — | — | — | — |
| 11 | Power GND | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 12 | +5V source A | — | W18 | — | 0.5 | OEM-2-K | — | — | — |
| 13 | Digital 2 | — | W32 | — | 0.5 | OEM-1-C | — | — | — |
| 14 | Digital 4 | — | W34 | — | 0.5 | OEM-1-P | — | — | — |
| 15 | Digital 8 | — | — | — | — | — | — | — | — |
| 16 | Digital 6 (turbo) | — | W36 | — | 0.5 | OEM-1-V | — | — | — |
| 17 | Power GND | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 18 | Ignition 6 | — | — | — | — | — | — | — | — |
| 19 | Power GND | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 20 | Digital GND | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 21 | Digital 1 (crank) | — | W19 | — | 0.5 | OEM-2-E | — | — | — |
| 22 | Digital 3 | — | W33 | — | 0.5 | OEM-1-N | — | — | — |
| 23 | Digital 7 | — | W37 | — | 0.5 | OEM-2-L | — | — | — |
| 24 | Digital 5 (turbo) | — | W35 | — | 0.5 | OEM-1-Q | — | — | — |
| 25 | Auxiliary 9 | — | — | — | — | — | — | — | — |
| 26 | Ignition 5 | — | — | — | — | — | — | — | — |
| 27 | Ignition 4 | — | — | — | — | — | — | — | — |
| 28 | Ignition 3 | — | — | — | — | — | — | — | — |
| 29 | Ignition 2 | — | W21 | — | 0.5 | OEM-1-H | — | — | — |
| 30 | Ignition 1 | — | W20 | — | 0.5 | OEM-1-G | — | — | — |
| 31 | CAN 1 high (PC comm) | — | — | — | — | — | — | — | — |
| 32 | CAN 1 low (PC comm) | — | — | — | — | — | — | — | — |
| 33 | CAN 2 high | — | — | — | — | — | — | — | — |
| 34 | CAN 2 low | — | — | — | — | — | — | — | — |
EMUPRO16-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Auxiliary 1 (WBO heater) | — | W26 | — | 0.5 | OEM-1-E | — | — | — |
| 2 | Auxiliary 2 (WBO heater) | — | W27 | — | 0.5 | OEM-2-I | — | — | — |
| 3 | Auxiliary 3 (WBO heater) | — | — | — | — | — | — | — | — |
| 4 | Auxiliary 4 (WBO heater) | — | — | — | — | — | — | — | — |
| 5 | Auxiliary 5 | — | — | — | — | — | — | — | — |
| 6 | Auxiliary 6 | — | — | — | — | — | — | — | — |
| 7 | Auxiliary 7 | — | — | — | — | — | — | — | — |
| 8 | +12V supply | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 9 | Digital GND (flash drive) | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 10 | USB D- (flash drive) | — | — | — | — | — | — | — | — |
| 11 | USB D+ (flash drive) | — | — | — | — | — | — | — | — |
| 12 | +5V source A (flash drive) | — | — | — | — | — | — | — | — |
| 13 | Auxiliary 8 | — | — | — | — | — | — | — | — |
| 14 | +12V supply | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 15 | +12V switched | — | — | — | — | — | — | — | — |
| 16 | Knock sensor 1 | — | — | — | — | — | — | — | — |
| 17 | Knock sensor 2 | — | — | — | — | — | — | — | — |
| 18 | WBO 2 VGND (LSU 4.9) | — | — | — | — | — | — | — | — |
| 19 | Power GND | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 20 | WBO 1 IP (LSU 4.9) | — | — | — | — | — | — | — | — |
| 21 | WBO 1 VS (LSU 4.9) | — | — | — | — | — | — | — | — |
| 22 | WBO 1 RCAL (LSU 4.9) | — | — | — | — | — | — | — | — |
| 23 | WBO 1 VGND (LSU 4.9) | — | — | — | — | — | — | — | — |
| 24 | WBO 2 IP (LSU 4.9) | — | — | — | — | — | — | — | — |
| 25 | WBO 2 VS (LSU 4.9) | — | — | — | — | — | — | — | — |
| 26 | WBO 2 RCAL (LSU 4.9) | — | — | — | — | — | — | — | — |
EMUPRO16-C
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Auxiliary 10 | — | — | — | — | — | — | — | — |
| 2 | Auxiliary 11 | — | — | — | — | — | — | — | — |
| 3 | Auxiliary 12 | — | — | — | — | — | — | — | — |
| 4 | Analog 7 | — | — | — | — | — | — | — | — |
| 5 | Analog 10 (2k2 pull) | — | — | — | — | — | — | — | — |
| 6 | H-bridge 1A | — | — | — | — | — | — | — | — |
| 7 | H-bridge 2B | — | — | — | — | — | — | — | — |
| 8 | H-bridge 3A | — | — | — | — | — | — | — | — |
| 9 | H-bridge 2A | — | — | — | — | — | — | — | — |
| 10 | Analog 1 (MAP) | — | — | — | — | — | — | — | — |
| 11 | Analog 3 | — | W31 | — | 0.5 | OEM-2-P | — | — | — |
| 12 | Analog 5 | — | — | — | — | — | — | — | — |
| 13 | Analog 8 | — | — | — | — | — | — | — | — |
| 14 | Analog 11 (2k2 pull) | — | — | — | — | — | — | — | — |
| 15 | Analog 13 (1k pull) | — | — | — | — | — | — | — | — |
| 16 | Analog 15 (330R pull) | — | — | — | — | — | — | — | — |
| 17 | H-bridge 3B | — | — | — | — | — | — | — | — |
| 18 | Analog 2 | — | W29 | — | 0.5 | OEM-2-N | — | — | — |
| 19 | Analog 4 | — | — | — | — | — | — | — | — |
| 20 | Analog 6 | — | — | — | — | — | — | — | — |
| 21 | Analog 9 (2k2 pull) | — | — | — | — | — | — | — | — |
| 22 | Analog 12 (2k2 pull) | — | — | — | — | — | — | — | — |
| 23 | Analog 14 (1k pull) | — | — | — | — | — | — | — | — |
| 24 | Analog 16 (100R pull) | — | — | — | — | — | — | — | — |
| 25 | H-bridge 1B | — | — | — | — | — | — | — | — |
| 26 | LIN | — | — | — | — | — | — | — | — |
| 27 | +5V source B | — | — | — | — | — | — | — | — |
| 28 | +5V source B | — | — | — | — | — | — | — | — |
| 29 | Analog GND | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 30 | Power GND | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 31 | Precision analog 1 | — | W28 | — | 0.5 | OEM-2-O | — | — | — |
| 32 | Precision analog 2 | — | W30 | — | 0.5 | OEM-2-Q | — | — | — |
| 33 | Precision analog 3 | — | — | — | — | — | — | — | — |
| 34 | Precision analog 4 | — | — | — | — | — | — | — | — |
EMUPRO16-D
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector 10 | — | — | — | — | — | — | — | — |
| 2 | Injector 11 | — | — | — | — | — | — | — | — |
| 3 | Injector 12 | — | — | — | — | — | — | — | — |
| 4 | Injector 13 | — | — | — | — | — | — | — | — |
| 5 | Injector 14 | — | — | — | — | — | — | — | — |
| 6 | Injector 15 | — | — | — | — | — | — | — | — |
| 7 | Injector 16 | — | — | — | — | — | — | — | — |
| 8 | Injector 9 | — | — | — | — | — | — | — | — |
| 9 | Analog 17 | — | — | — | — | — | — | — | — |
| 10 | Analog 18 | — | — | — | — | — | — | — | — |
| 11 | Digital 9 / Analog 19 | — | — | — | — | — | — | — | — |
| 12 | Digital 10 / Analog 20 | — | — | — | — | — | — | — | — |
| 13 | Auxiliary 13 | — | — | — | — | — | — | — | — |
| 14 | H-bridge 4A | — | — | — | — | — | — | — | — |
| 15 | Precision analog 6 | — | — | — | — | — | — | — | — |
| 16 | Precision analog 8 | — | — | — | — | — | — | — | — |
| 17 | Analog GND | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 18 | Power GND | — | W11 | — | 0.85 | SP-GND-1 | — | — | — |
| 19 | Auxiliary 14 | — | — | — | — | — | — | — | — |
| 20 | H-bridge 4B | — | — | — | — | — | — | — | — |
| 21 | Precision analog 5 | — | — | — | — | — | — | — | — |
| 22 | Precision analog 7 | — | — | — | — | — | — | — | — |
| 23 | Ignition 9 | — | — | — | — | — | — | — | — |
| 24 | Ignition 10 | — | — | — | — | — | — | — | — |
| 25 | Auxiliary 16 | — | — | — | — | — | — | — | — |
| 26 | Auxiliary 15 | — | — | — | — | — | — | — | — |
OEM-1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A | Constant +12V | — | — | — | — | — | — | — | — |
| B | ECU power +14V (main relay) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| C | Start signal | — | W32 | — | 0.5 | EMUPRO16-A-13 | — | — | — |
| E | Malfunction indicator lamp (MIL) | — | W26 | — | 0.5 | EMUPRO16-B-1 | — | — | — |
| G | Ignition 1 (coils 1+4, wasted spark) | — | W20 | — | 0.5 | EMUPRO16-A-30 | — | — | — |
| H | Ignition 2 (coils 2+3, wasted spark) | — | W21 | — | 0.5 | EMUPRO16-A-29 | — | — | — |
| N | Wide-open throttle switch | — | W33 | — | 0.5 | EMUPRO16-A-22 | — | — | — |
| P | Power steering pressure switch | — | W34 | — | 0.5 | EMUPRO16-A-14 | — | — | — |
| Q | A/C request | — | W35 | — | 0.5 | EMUPRO16-A-24 | — | — | — |
| V | Neutral/clutch switch | — | W36 | — | 0.5 | EMUPRO16-A-16 | — | — | — |
OEM-2
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A | Power ground | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| B | Power ground | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| C | Sensor ground (E2) | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| D | Sensor ground (E2) | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| E | Crank position (CAS NE) | — | W19 | — | 0.5 | EMUPRO16-A-21 | — | — | — |
| F | NC | — | — | — | — | — | — | — | — |
| G | Cam position (CAS G) | — | — | — | — | — | — | — | — |
| I | Tachometer output | — | W27 | — | 0.5 | EMUPRO16-B-2 | — | — | — |
| K | +5V sensor supply | — | W18 | — | 0.5 | EMUPRO16-A-12 | — | — | — |
| L | Idle switch (TPS) | — | W37 | — | 0.5 | EMUPRO16-A-23 | — | — | — |
| N | O2 sensor | — | W29 | — | 0.5 | EMUPRO16-C-18 | — | — | — |
| O | Air flow meter (AFM) | — | W28 | — | 0.5 | EMUPRO16-C-31 | — | — | — |
| P | Intake air temperature (IAT) | — | W31 | — | 0.5 | EMUPRO16-C-11 | — | — | — |
| Q | Coolant temperature (ECT) | — | W30 | — | 0.5 | EMUPRO16-C-32 | — | — | — |
| U | Injector 1 & 3 (batch) | — | W22 | — | 0.5 | EMUPRO16-A-2 | — | — | — |
| V | Injector 2 & 4 (batch) | — | W23 | — | 0.5 | EMUPRO16-A-3 | — | — | — |
| Y | Injector 3 (California sequential) | — | W24 | — | 0.5 | EMUPRO16-A-4 | — | — | — |
| Z | Injector 4 (California sequential) | — | W25 | — | 0.5 | EMUPRO16-A-5 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W12 | — | 0.5 | OEM-2-C | — | — | — |
| 1 | — | — | W13 | — | 0.5 | OEM-2-D | — | — | — |
| 1 | — | — | W14 | — | 0.5 | EMUPRO16-A-20 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | EMUPRO16-B-9 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | EMUPRO16-C-29 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | EMUPRO16-D-17 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-1-B | — | — | — |
| 1 | — | — | W2 | — | 0.85 | EMUPRO16-B-14 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | EMUPRO16-B-8 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W4 | — | 0.85 | OEM-2-A | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-2-B | — | — | — |
| 1 | — | — | W6 | — | 0.85 | EMUPRO16-A-11 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | EMUPRO16-A-17 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | EMUPRO16-A-19 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | EMUPRO16-B-19 | — | — | — |
| 1 | — | — | W10 | — | 0.85 | EMUPRO16-C-30 | — | — | — |
| 1 | — | — | W11 | — | 0.85 | EMUPRO16-D-18 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-1-A | Constant +12V | power_in | — | — | — | single_source | |
| OEM-1-B | ECU power +14V (main relay) | power_in | EMUPRO16-B-14 + EMUPRO16-B-8 | +12V supply + +12V supply | power_in | single_source | |
| OEM-1-C | Start signal | digital_in | EMUPRO16-A-13 | Digital 2 | digital_in | single_source | |
| OEM-1-E | Malfunction indicator lamp (MIL) | low_side_out | EMUPRO16-B-1 | Auxiliary 1 (WBO heater) | low_side_out | single_source | |
| OEM-1-G | Ignition 1 (coils 1+4, wasted spark) | ignition_out | EMUPRO16-A-30 | Ignition 1 | ignition_out | single_source | |
| OEM-1-H | Ignition 2 (coils 2+3, wasted spark) | ignition_out | EMUPRO16-A-29 | Ignition 2 | ignition_out | single_source | |
| OEM-1-N | Wide-open throttle switch | digital_in | EMUPRO16-A-22 | Digital 3 | digital_in | single_source | |
| OEM-1-P | Power steering pressure switch | digital_in | EMUPRO16-A-14 | Digital 4 | digital_in | single_source | |
| OEM-1-Q | A/C request | digital_in | EMUPRO16-A-24 | Digital 5 (turbo) | digital_in | single_source | |
| OEM-1-V | Neutral/clutch switch | digital_in | EMUPRO16-A-16 | Digital 6 (turbo) | digital_in | single_source | |
| OEM-2-A | Power ground | ground | EMUPRO16-A-11 + EMUPRO16-A-17 + EMUPRO16-A-19 + EMUPRO16-B-19 + EMUPRO16-C-30 + EMUPRO16-D-18 | Power GND + Power GND + Power GND + Power GND + Power GND + Power GND | ground | single_source | |
| OEM-2-B | Power ground | ground | EMUPRO16-A-11 + EMUPRO16-A-17 + EMUPRO16-A-19 + EMUPRO16-B-19 + EMUPRO16-C-30 + EMUPRO16-D-18 | Power GND + Power GND + Power GND + Power GND + Power GND + Power GND | ground | single_source | |
| OEM-2-C | Sensor ground (E2) | sensor_ground | EMUPRO16-A-20 + EMUPRO16-B-9 + EMUPRO16-C-29 + EMUPRO16-D-17 | Digital GND + Digital GND (flash drive) + Analog GND + Analog GND | sensor_ground | corroborated | |
| OEM-2-D | Sensor ground (E2) | sensor_ground | EMUPRO16-A-20 + EMUPRO16-B-9 + EMUPRO16-C-29 + EMUPRO16-D-17 | Digital GND + Digital GND (flash drive) + Analog GND + Analog GND | sensor_ground | corroborated | |
| OEM-2-E | Crank position (CAS NE) | trigger_in | EMUPRO16-A-21 | Digital 1 (crank) | trigger_in | single_source | |
| OEM-2-F | NC | — | — | — | — | corroborated | |
| OEM-2-G | Cam position (CAS G) | trigger_in | — | — | — | single_source | |
| OEM-2-I | Tachometer output | tacho_out | EMUPRO16-B-2 | Auxiliary 2 (WBO heater) | low_side_out | single_source | |
| OEM-2-K | +5V sensor supply | vref | EMUPRO16-A-12 | +5V source A | vref | single_source | |
| OEM-2-L | Idle switch (TPS) | digital_in | EMUPRO16-A-23 | Digital 7 | digital_in | single_source | |
| OEM-2-N | O2 sensor | lambda_nb_in | EMUPRO16-C-18 | Analog 2 | analog_in | single_source | |
| OEM-2-O | Air flow meter (AFM) | analog_in | EMUPRO16-C-31 | Precision analog 1 | analog_in | single_source | |
| OEM-2-P | Intake air temperature (IAT) | temp_in | EMUPRO16-C-11 | Analog 3 | analog_in | single_source | |
| OEM-2-Q | Coolant temperature (ECT) | temp_in | EMUPRO16-C-32 | Precision analog 2 | analog_in | single_source | |
| OEM-2-U | Injector 1 & 3 (batch) | injector_out | EMUPRO16-A-2 | Injector 1 | injector_out | corroborated | |
| OEM-2-V | Injector 2 & 4 (batch) | injector_out | EMUPRO16-A-3 | Injector 2 | injector_out | corroborated | |
| OEM-2-Y | Injector 3 (California sequential) | injector_out | EMUPRO16-A-4 | Injector 3 | injector_out | corroborated | |
| OEM-2-Z | Injector 4 (California sequential) | injector_out | EMUPRO16-A-5 | Injector 4 | injector_out | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-1-B | SP-14V-1 | 0.85 | no route | ECU power +14V (main relay) | — | |
| W2 | SP-14V-1 | EMUPRO16-B-14 | 0.85 | no route | +12V supply | — | |
| W3 | SP-14V-1 | EMUPRO16-B-8 | 0.85 | no route | +12V supply | — | |
| W4 | OEM-2-A | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W5 | OEM-2-B | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W6 | SP-GND-1 | EMUPRO16-A-11 | 0.85 | no route | Power GND | — | |
| W7 | SP-GND-1 | EMUPRO16-A-17 | 0.85 | no route | Power GND | — | |
| W8 | SP-GND-1 | EMUPRO16-A-19 | 0.85 | no route | Power GND | — | |
| W9 | SP-GND-1 | EMUPRO16-B-19 | 0.85 | no route | Power GND | — | |
| W10 | SP-GND-1 | EMUPRO16-C-30 | 0.85 | no route | Power GND | — | |
| W11 | SP-GND-1 | EMUPRO16-D-18 | 0.85 | no route | Power GND | — | |
| W12 | OEM-2-C | SP-0V-1 | 0.5 | no route | Sensor ground (E2) | — | |
| W13 | OEM-2-D | SP-0V-1 | 0.5 | no route | Sensor ground (E2) | — | |
| W14 | SP-0V-1 | EMUPRO16-A-20 | 0.5 | no route | Digital GND | — | |
| W15 | SP-0V-1 | EMUPRO16-B-9 | 0.5 | no route | Digital GND (flash drive) | — | |
| W16 | SP-0V-1 | EMUPRO16-C-29 | 0.5 | no route | Analog GND | — | |
| W17 | SP-0V-1 | EMUPRO16-D-17 | 0.5 | no route | Analog GND | — | |
| W18 | OEM-2-K | EMUPRO16-A-12 | 0.5 | no route | +5V sensor supply | — | |
| W19 | OEM-2-E | EMUPRO16-A-21 | 0.5 | no route | Crank position (CAS NE) | — | |
| W20 | OEM-1-G | EMUPRO16-A-30 | 0.5 | no route | Ignition 1 (coils 1+4, wasted spark) | — | |
| W21 | OEM-1-H | EMUPRO16-A-29 | 0.5 | no route | Ignition 2 (coils 2+3, wasted spark) | — | |
| W22 | OEM-2-U | EMUPRO16-A-2 | 0.5 | no route | Injector 1 & 3 (batch) | — | |
| W23 | OEM-2-V | EMUPRO16-A-3 | 0.5 | no route | Injector 2 & 4 (batch) | — | |
| W24 | OEM-2-Y | EMUPRO16-A-4 | 0.5 | no route | Injector 3 (California sequential) | — | |
| W25 | OEM-2-Z | EMUPRO16-A-5 | 0.5 | no route | Injector 4 (California sequential) | — | |
| W26 | OEM-1-E | EMUPRO16-B-1 | 0.5 | no route | Malfunction indicator lamp (MIL) | — | |
| W27 | OEM-2-I | EMUPRO16-B-2 | 0.5 | no route | Tachometer output | — | |
| W28 | OEM-2-O | EMUPRO16-C-31 | 0.5 | no route | Air flow meter (AFM) | — | |
| W29 | OEM-2-N | EMUPRO16-C-18 | 0.5 | no route | O2 sensor | — | |
| W30 | OEM-2-Q | EMUPRO16-C-32 | 0.5 | no route | Coolant temperature (ECT) | — | |
| W31 | OEM-2-P | EMUPRO16-C-11 | 0.5 | no route | Intake air temperature (IAT) | — | |
| W32 | OEM-1-C | EMUPRO16-A-13 | 0.5 | no route | Start signal | — | |
| W33 | OEM-1-N | EMUPRO16-A-22 | 0.5 | no route | Wide-open throttle switch | — | |
| W34 | OEM-1-P | EMUPRO16-A-14 | 0.5 | no route | Power steering pressure switch | — | |
| W35 | OEM-1-Q | EMUPRO16-A-24 | 0.5 | no route | A/C request | — | |
| W36 | OEM-1-V | EMUPRO16-A-16 | 0.5 | no route | Neutral/clutch switch | — | |
| W37 | OEM-2-L | EMUPRO16-A-23 | 0.5 | no route | Idle switch (TPS) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 1473416-1 | TE | Superseal 1.0 26-way plug, Key 3 | 1.000 | ea |
| connector | 174515-6 | TE | AMP Multilock .040/.070 hybrid 22-pin female harness plug (Miata NA/NB ECU) | 1.000 | ea |
| connector | 174516-6 | TE | AMP Multilock .040/.070 hybrid 26-pin female harness plug (Miata NA/NB ECU) | 1.000 | ea |
| connector | 3-1437290-7 | TE | Superseal 1.0 26-way plug | 1.000 | ea |
| connector | 4-1437290-0 | TE | Superseal 1.0 34-way plug, Key 1 | 1.000 | ea |
| connector | 4-1437290-1 | TE | Superseal 1.0 34-way plug, Key 2 | 1.000 | ea |
| terminal | 3-1447221-4 | TE | Superseal 1.0 socket terminal, 20 AWG (0.5 sq mm) | 32.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (5)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | REQUIRED_UNMAPPED | OEM-2-G | Required OEM function "Cam position (CAS G)" (trigger_in) is not connected to the new ECU. |
| warn | NO_FUEL_PUMP | fuel pump | This engine harness has no fuel-pump control path: no fuel-pump relay output is wired to the new ECU. If the stock car switches the pump outside the ECU (an airflow-meter contact or a separate module), the standalone must drive the pump relay itself — see the install notes for this car. |
| info | NET_FAMILY | OEM-2-I ↔ EMUPRO16-B-2 | OEM-2-I "Tachometer output" [tacho_out] is wired to EMUPRO16-B-2 "Auxiliary 2 (WBO heater)" [low_side_out]. Tacho as a low-side output: check the tach needs a pull-up. |
| info | NET_FAMILY | OEM-2-P ↔ EMUPRO16-C-11 | OEM-2-P "Intake air temperature (IAT)" [temp_in] is wired to EMUPRO16-C-11 "Analog 3" [analog_in]. Thermistor on a plain analog input needs a pull-up; check the channel can enable one. |
| info | NET_FAMILY | OEM-2-Q ↔ EMUPRO16-C-32 | OEM-2-Q "Coolant temperature (ECT)" [temp_in] is wired to EMUPRO16-C-32 "Precision analog 2" [analog_in]. Thermistor on a plain analog input needs a pull-up; check the channel can enable one. |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-1-A | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-09. Review every wire against both manuals before building. Open items: - OEM-2 G: Cam position (CAS G): no free cam_hall/cam_vr/frequency_in input on ECUMASTER EMU PRO 16 - Fuel-pump control: ECUMASTER EMU PRO 16 needs to drive the fuel pump, but the stock ECU has no fuel-pump output (an airflow-meter contact or a separate module runs it). Add a fuel-pump relay on a spare low-side output — see the install notes for this car. Not wired: - OEM-1 A: Constant +12V: ECUMASTER EMU PRO 16 has no battery-constant input; not needed - EMUPRO16-B 15: +12V switched: not fed (the stock ECU has no ignition-sense pin); feed it from a switched-ignition source
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | ECUMASTER EMU PRO 16 — pinout (Connectors A/B/C/D) | https://www.ecumaster.com/files/EMU_PRO/EMU_PRO_16_Pinout_v1.0.pdf | archive | 2026-10-05 | 72799bed63fb |
| 4 | vendor_doc | Link G4X MX5X install manual (NA 1.6/1.8) | https://linkecu.com/documentation/MX5X.pdf | archive | 2026-10-05 | b7f730de9f6e |
| 2 | community_copy | 1991 Mazda Miata wiring diagrams (Mitchell reproduction, mellens.net community mirror) | https://trull.org/alex/pubmirror/www.mellens.net/mazda/Mazda-Miata-1991-1993/1991_wiring.pdf | — | 2026-10-08 | 6f957a38ed49 |
| 2 | expert_report | Justin Barrera — Miata NA/NB wiring corrections | — | — | — | — |