MX-5 Miata NA6 1990-93 (B6-ZE, 1.6) → MoTeC M800 universal (auto)
MX-5 Miata NA6 1990-93 (B6-ZE, 1.6) — MoTeC — M800
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-09
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
Install modifications
Steps on the car itself, outside the harness. Every harness for this car inherits them.
- Cut the sensor-ground-to-chassis wirerequired
Cut the wire in the engine bay that ties the ECU sensor/signal ground (2C/2D, BLK/LT GRN) to chassis ground, so the standalone gets a clean sensor-ground reference. After cutting, verify with a meter: sensor ground ↔ chassis ground reads open (OL) unless the standalone manual says otherwise.
Why: The stock loom bonds sensor ground to chassis ground; a standalone ECU needs its sensor ground isolated from the noisy chassis/power ground, otherwise sensor readings are noisy or wrong.
Where: Engine-bay ground joint near the ECU (1991 EWD Fig.2 shows the sensor-ground run and its joint connector).
Correction reported by Justin Barrera
Unverified — reported by Justin Barrera (Motorsport Wiring Alliance), not yet sourced.
- Bypass the airflow-meter pump switchrecommended
The stock pump is run by the flapper airflow meter's pump-switch contact through the circuit-opening relay, not by the ECU. The standalone harness adds ECU control of the pump relay (ignition-switched, fused); remove/bypass the AFM pump switch so the two do not fight.
Why: There is no stock fuel-pump output at the ECU, so the standalone provides it. Leaving the AFM switch in place leaves a second, unswitched pump path.
Where: Airflow meter connector (pump-switch contact) and circuit-opening relay.
Correction reported by Justin Barrera
Source: 1991 Mazda Miata wiring diagrams (Mitchell reproduction, mellens.net community mirror)
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | none |
| Size of the job | 32 wires · 7 connectors · 5 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Terminals | 3-1447221-4 |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-1-B | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | SP-14V-1 | M800-A-26 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | OEM-2-A | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-2-B | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | SP-GND-1 | M800-A-10 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | SP-GND-1 | M800-A-11 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-2-C | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-2-D | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-0V-1 | M800-B-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | SP-0V-1 | M800-B-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | SP-0V-1 | M800-B-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-2-K | M800-A-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-2-E | M800-B-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-2-G | M800-B-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-1-G | M800-A-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-1-H | M800-A-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-2-U | M800-A-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-2-V | M800-A-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-2-Y | M800-A-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-2-Z | M800-A-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-1-E | M800-A-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-2-I | M800-A-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-2-O | M800-A-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-2-N | M800-A-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-2-Q | M800-B-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-2-P | M800-B-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-1-C | M800-B-8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-1-N | M800-B-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-1-P | M800-B-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-1-Q | M800-B-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-1-V | M800-A-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-2-L | M800-A-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Pre-power install steps (make these cuts/modifications on the car first, then verify the checks below): Cut the sensor-ground-to-chassis wire.
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | M800-A-26 | M800-A-10 | open (OL) | +12 V supply must not touch power ground | |
| 2 | M800-A-26 | M800-B-14 | open (OL) | +12 V supply must not touch sensor ground | |
| 3 | M800-A-10 | M800-A-2 | open (OL) | power ground must not touch 5 V sensor reference | |
| 4 | M800-A-26 | M800-A-2 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 5 | M800-B-14 | M800-A-2 | open (OL) | sensor ground must not touch 5 V sensor reference |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
M800-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | AUX2 | — | W22 | — | 0.5 | OEM-2-I | — | — | — |
| 2 | 5V Engine Sensor Supply | — | W12 | — | 0.5 | OEM-2-K | — | — | — |
| 3 | IGN1 | — | W15 | — | 0.5 | OEM-1-G | — | — | — |
| 4 | IGN2 | — | W16 | — | 0.5 | OEM-1-H | — | — | — |
| 5 | IGN3 | — | — | — | — | — | — | — | — |
| 6 | IGN4 | — | — | — | — | — | — | — | — |
| 7 | IGN5 | — | — | — | — | — | — | — | — |
| 8 | IGN6 | — | — | — | — | — | — | — | — |
| 9 | 5V Auxiliary Sensor Supply | — | — | — | — | — | — | — | — |
| 10 | GND Battery Negative | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 11 | GND Battery Negative | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 12 | 8V Engine Sensor Supply | — | — | — | — | — | — | — | — |
| 13 | 8V Auxiliary Sensor and CAN Supply | — | — | — | — | — | — | — | — |
| 14 | AV1 | — | W23 | — | 0.5 | OEM-2-O | — | — | — |
| 15 | Analog Voltage Input 2 | — | W24 | — | 0.5 | OEM-2-N | — | — | — |
| 16 | Analog Voltage Input 3 | — | W31 | — | 0.5 | OEM-1-V | — | — | — |
| 17 | Analog Voltage Input 4 | — | W32 | — | 0.5 | OEM-2-L | — | — | — |
| 18 | AUX1 | — | W21 | — | 0.5 | OEM-1-E | — | — | — |
| 19 | INJ1 | — | W17 | — | 0.5 | OEM-2-U | — | — | — |
| 20 | INJ2 | — | W18 | — | 0.5 | OEM-2-V | — | — | — |
| 21 | INJ3 | — | W19 | — | 0.5 | OEM-2-Y | — | — | — |
| 22 | INJ4 | — | W20 | — | 0.5 | OEM-2-Z | — | — | — |
| 23 | AUX3 | — | — | — | — | — | — | — | — |
| 24 | AUX4 | — | — | — | — | — | — | — | — |
| 25 | Analog Voltage Input 5 | — | — | — | — | — | — | — | — |
| 26 | VBAT Battery Positive | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 27 | INJ5 | — | — | — | — | — | — | — | — |
| 28 | INJ6 | — | — | — | — | — | — | — | — |
| 29 | INJ7 | — | — | — | — | — | — | — | — |
| 30 | INJ8 | — | — | — | — | — | — | — | — |
| 31 | AUX5 | — | — | — | — | — | — | — | — |
| 32 | AUX6 | — | — | — | — | — | — | — | — |
| 33 | AUX7 | — | — | — | — | — | — | — | — |
| 34 | AUX8 | — | — | — | — | — | — | — | — |
M800-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Crank Reference Timing Input | — | W13 | — | 0.5 | OEM-2-E | — | — | — |
| 2 | Cam Sync Timing Input | — | W14 | — | 0.5 | OEM-2-G | — | — | — |
| 3 | Analog Temperature Input 1 | — | W25 | — | 0.5 | OEM-2-Q | — | — | — |
| 4 | Analog Temperature Input 2 | — | W26 | — | 0.5 | OEM-2-P | — | — | — |
| 5 | Analog Temperature Input 3 | — | — | — | — | — | — | — | — |
| 6 | Analog Temperature Input 4 | — | — | — | — | — | — | — | — |
| 7 | Analog Temperature Input 5 | — | — | — | — | — | — | — | — |
| 8 | Digital Input 1 | — | W27 | — | 0.5 | OEM-1-C | — | — | — |
| 9 | Digital Input 2 | — | W28 | — | 0.5 | OEM-1-N | — | — | — |
| 10 | Digital Input 3 | — | W29 | — | 0.5 | OEM-1-P | — | — | — |
| 11 | Digital Input 4 | — | W30 | — | 0.5 | OEM-1-Q | — | — | — |
| 12 | Lambda2 Sense Voltage | — | — | — | — | — | — | — | — |
| 13 | Lambda2 Pump Current | — | — | — | — | — | — | — | — |
| 14 | 0V Comms Reference | — | W9 | — | 0.5 | SP-0V-1 | — | — | — |
| 15 | 0V Auxiliary Sensor Supply | — | W10 | — | 0.5 | SP-0V-1 | — | — | — |
| 16 | 0V Engine Sensor Supply | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| 17 | RS232 Transmit Data | — | — | — | — | — | — | — | — |
| 18 | RS232 Receive Data | — | — | — | — | — | — | — | — |
| 19 | Analog Temperature Input 6 | — | — | — | — | — | — | — | — |
| 20 | Analog Voltage Input 6 | — | — | — | — | — | — | — | — |
| 21 | AV7 | — | — | — | — | — | — | — | — |
| 22 | AV8 | — | — | — | — | — | — | — | — |
| 23 | CAN Bus High | — | — | — | — | — | — | — | — |
| 24 | CAN Bus Low | — | — | — | — | — | — | — | — |
| 25 | Lambda1 Sense Voltage | — | — | — | — | — | — | — | — |
| 26 | Lambda1 Pump Current | — | — | — | — | — | — | — | — |
OEM-1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A | Constant +12V | — | — | — | — | — | — | — | — |
| B | ECU power +14V (main relay) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| C | Start signal | — | W27 | — | 0.5 | M800-B-8 | — | — | — |
| E | Malfunction indicator lamp (MIL) | — | W21 | — | 0.5 | M800-A-18 | — | — | — |
| G | Ignition 1 (coils 1+4, wasted spark) | — | W15 | — | 0.5 | M800-A-3 | — | — | — |
| H | Ignition 2 (coils 2+3, wasted spark) | — | W16 | — | 0.5 | M800-A-4 | — | — | — |
| N | Wide-open throttle switch | — | W28 | — | 0.5 | M800-B-9 | — | — | — |
| P | Power steering pressure switch | — | W29 | — | 0.5 | M800-B-10 | — | — | — |
| Q | A/C request | — | W30 | — | 0.5 | M800-B-11 | — | — | — |
| V | Neutral/clutch switch | — | W31 | — | 0.5 | M800-A-16 | — | — | — |
OEM-2
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A | Power ground | — | W3 | — | 0.85 | SP-GND-1 | — | — | — |
| B | Power ground | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| C | Sensor ground (E2) | — | W7 | — | 0.5 | SP-0V-1 | — | — | — |
| D | Sensor ground (E2) | — | W8 | — | 0.5 | SP-0V-1 | — | — | — |
| E | Crank position (CAS NE) | — | W13 | — | 0.5 | M800-B-1 | — | — | — |
| F | NC | — | — | — | — | — | — | — | — |
| G | Cam position (CAS G) | — | W14 | — | 0.5 | M800-B-2 | — | — | — |
| I | Tachometer output | — | W22 | — | 0.5 | M800-A-1 | — | — | — |
| K | +5V sensor supply | — | W12 | — | 0.5 | M800-A-2 | — | — | — |
| L | Idle switch (TPS) | — | W32 | — | 0.5 | M800-A-17 | — | — | — |
| N | O2 sensor | — | W24 | — | 0.5 | M800-A-15 | — | — | — |
| O | Air flow meter (AFM) | — | W23 | — | 0.5 | M800-A-14 | — | — | — |
| P | Intake air temperature (IAT) | — | W26 | — | 0.5 | M800-B-4 | — | — | — |
| Q | Coolant temperature (ECT) | — | W25 | — | 0.5 | M800-B-3 | — | — | — |
| U | Injector 1 & 3 (batch) | — | W17 | — | 0.5 | M800-A-19 | — | — | — |
| V | Injector 2 & 4 (batch) | — | W18 | — | 0.5 | M800-A-20 | — | — | — |
| Y | Injector 3 (California sequential) | — | W19 | — | 0.5 | M800-A-21 | — | — | — |
| Z | Injector 4 (California sequential) | — | W20 | — | 0.5 | M800-A-22 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W7 | — | 0.5 | OEM-2-C | — | — | — |
| 1 | — | — | W8 | — | 0.5 | OEM-2-D | — | — | — |
| 1 | — | — | W9 | — | 0.5 | M800-B-14 | — | — | — |
| 1 | — | — | W10 | — | 0.5 | M800-B-15 | — | — | — |
| 1 | — | — | W11 | — | 0.5 | M800-B-16 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-1-B | — | — | — |
| 1 | — | — | W2 | — | 0.85 | M800-A-26 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W3 | — | 0.85 | OEM-2-A | — | — | — |
| 1 | — | — | W4 | — | 0.85 | OEM-2-B | — | — | — |
| 1 | — | — | W5 | — | 0.85 | M800-A-10 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | M800-A-11 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-1-A | Constant +12V | power_in | — | — | — | single_source | |
| OEM-1-B | ECU power +14V (main relay) | power_in | M800-A-26 | VBAT Battery Positive | power_in | single_source | |
| OEM-1-C | Start signal | digital_in | M800-B-8 | Digital Input 1 | digital_in | single_source | |
| OEM-1-E | Malfunction indicator lamp (MIL) | low_side_out | M800-A-18 | AUX1 | switch_out | single_source | |
| OEM-1-G | Ignition 1 (coils 1+4, wasted spark) | ignition_out | M800-A-3 | IGN1 | ignition_out | single_source | |
| OEM-1-H | Ignition 2 (coils 2+3, wasted spark) | ignition_out | M800-A-4 | IGN2 | ignition_out | single_source | |
| OEM-1-N | Wide-open throttle switch | digital_in | M800-B-9 | Digital Input 2 | digital_in | single_source | |
| OEM-1-P | Power steering pressure switch | digital_in | M800-B-10 | Digital Input 3 | digital_in | single_source | |
| OEM-1-Q | A/C request | digital_in | M800-B-11 | Digital Input 4 | digital_in | single_source | |
| OEM-1-V | Neutral/clutch switch | digital_in | M800-A-16 | Analog Voltage Input 3 | analog_in | single_source | |
| OEM-2-A | Power ground | ground | M800-A-10 + M800-A-11 | GND Battery Negative + GND Battery Negative | ground | single_source | |
| OEM-2-B | Power ground | ground | M800-A-10 + M800-A-11 | GND Battery Negative + GND Battery Negative | ground | single_source | |
| OEM-2-C | Sensor ground (E2) | sensor_ground | M800-B-14 + M800-B-15 + M800-B-16 | 0V Comms Reference + 0V Auxiliary Sensor Supply + 0V Engine Sensor Supply | sensor_ground | corroborated | |
| OEM-2-D | Sensor ground (E2) | sensor_ground | M800-B-14 + M800-B-15 + M800-B-16 | 0V Comms Reference + 0V Auxiliary Sensor Supply + 0V Engine Sensor Supply | sensor_ground | corroborated | |
| OEM-2-E | Crank position (CAS NE) | trigger_in | M800-B-1 | Crank Reference Timing Input | trigger_in | single_source | |
| OEM-2-F | NC | — | — | — | — | corroborated | |
| OEM-2-G | Cam position (CAS G) | trigger_in | M800-B-2 | Cam Sync Timing Input | trigger_in | single_source | |
| OEM-2-I | Tachometer output | tacho_out | M800-A-1 | AUX2 | switch_out | single_source | |
| OEM-2-K | +5V sensor supply | vref | M800-A-2 | 5V Engine Sensor Supply | vref | single_source | |
| OEM-2-L | Idle switch (TPS) | digital_in | M800-A-17 | Analog Voltage Input 4 | analog_in | single_source | |
| OEM-2-N | O2 sensor | lambda_nb_in | M800-A-15 | Analog Voltage Input 2 | analog_in | single_source | |
| OEM-2-O | Air flow meter (AFM) | analog_in | M800-A-14 | AV1 | analog_in | single_source | |
| OEM-2-P | Intake air temperature (IAT) | temp_in | M800-B-4 | Analog Temperature Input 2 | temp_in | single_source | |
| OEM-2-Q | Coolant temperature (ECT) | temp_in | M800-B-3 | Analog Temperature Input 1 | temp_in | single_source | |
| OEM-2-U | Injector 1 & 3 (batch) | injector_out | M800-A-19 | INJ1 | injector_out | corroborated | |
| OEM-2-V | Injector 2 & 4 (batch) | injector_out | M800-A-20 | INJ2 | injector_out | corroborated | |
| OEM-2-Y | Injector 3 (California sequential) | injector_out | M800-A-21 | INJ3 | injector_out | corroborated | |
| OEM-2-Z | Injector 4 (California sequential) | injector_out | M800-A-22 | INJ4 | injector_out | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-1-B | SP-14V-1 | 0.85 | no route | ECU power +14V (main relay) | — | |
| W2 | SP-14V-1 | M800-A-26 | 0.85 | no route | VBAT Battery Positive | — | |
| W3 | OEM-2-A | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W4 | OEM-2-B | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W5 | SP-GND-1 | M800-A-10 | 0.85 | no route | GND Battery Negative | — | |
| W6 | SP-GND-1 | M800-A-11 | 0.85 | no route | GND Battery Negative | — | |
| W7 | OEM-2-C | SP-0V-1 | 0.5 | no route | Sensor ground (E2) | — | |
| W8 | OEM-2-D | SP-0V-1 | 0.5 | no route | Sensor ground (E2) | — | |
| W9 | SP-0V-1 | M800-B-14 | 0.5 | no route | 0V Comms Reference | — | |
| W10 | SP-0V-1 | M800-B-15 | 0.5 | no route | 0V Auxiliary Sensor Supply | — | |
| W11 | SP-0V-1 | M800-B-16 | 0.5 | no route | 0V Engine Sensor Supply | — | |
| W12 | OEM-2-K | M800-A-2 | 0.5 | no route | +5V sensor supply | — | |
| W13 | OEM-2-E | M800-B-1 | 0.5 | no route | Crank position (CAS NE) | — | |
| W14 | OEM-2-G | M800-B-2 | 0.5 | no route | Cam position (CAS G) | — | |
| W15 | OEM-1-G | M800-A-3 | 0.5 | no route | Ignition 1 (coils 1+4, wasted spark) | — | |
| W16 | OEM-1-H | M800-A-4 | 0.5 | no route | Ignition 2 (coils 2+3, wasted spark) | — | |
| W17 | OEM-2-U | M800-A-19 | 0.5 | no route | Injector 1 & 3 (batch) | — | |
| W18 | OEM-2-V | M800-A-20 | 0.5 | no route | Injector 2 & 4 (batch) | — | |
| W19 | OEM-2-Y | M800-A-21 | 0.5 | no route | Injector 3 (California sequential) | — | |
| W20 | OEM-2-Z | M800-A-22 | 0.5 | no route | Injector 4 (California sequential) | — | |
| W21 | OEM-1-E | M800-A-18 | 0.5 | no route | Malfunction indicator lamp (MIL) | — | |
| W22 | OEM-2-I | M800-A-1 | 0.5 | no route | Tachometer output | — | |
| W23 | OEM-2-O | M800-A-14 | 0.5 | no route | Air flow meter (AFM) | — | |
| W24 | OEM-2-N | M800-A-15 | 0.5 | no route | O2 sensor | — | |
| W25 | OEM-2-Q | M800-B-3 | 0.5 | no route | Coolant temperature (ECT) | — | |
| W26 | OEM-2-P | M800-B-4 | 0.5 | no route | Intake air temperature (IAT) | — | |
| W27 | OEM-1-C | M800-B-8 | 0.5 | no route | Start signal | — | |
| W28 | OEM-1-N | M800-B-9 | 0.5 | no route | Wide-open throttle switch | — | |
| W29 | OEM-1-P | M800-B-10 | 0.5 | no route | Power steering pressure switch | — | |
| W30 | OEM-1-Q | M800-B-11 | 0.5 | no route | A/C request | — | |
| W31 | OEM-1-V | M800-A-16 | 0.5 | no route | Neutral/clutch switch | — | |
| W32 | OEM-2-L | M800-A-17 | 0.5 | no route | Idle switch (TPS) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 174515-6 | TE | AMP Multilock .040/.070 hybrid 22-pin female harness plug (Miata NA/NB ECU) | 1.000 | ea |
| connector | 174516-6 | TE | AMP Multilock .040/.070 hybrid 26-pin female harness plug (Miata NA/NB ECU) | 1.000 | ea |
| connector | 3-1437290-7 | TE | Superseal 1.0 26-way plug | 1.000 | ea |
| connector | 4-1437290-0 | TE | Superseal 1.0 34-way plug, Key 1 | 1.000 | ea |
| terminal | 3-1447221-4 | TE | Superseal 1.0 socket terminal, 20 AWG (0.5 sq mm) | 27.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (5)
| Severity | Code | Subject | Message |
|---|---|---|---|
| warn | NET_FAMILY | OEM-1-V ↔ M800-A-16 | OEM-1-V "Neutral/clutch switch" [digital_in] is wired to M800-A-16 "Analog Voltage Input 3" [analog_in]. Analog and digital on one net. A switch on an analog input works with a pull-up and a threshold; an analog sensor on a digital input loses its value. |
| warn | NET_FAMILY | OEM-2-L ↔ M800-A-17 | OEM-2-L "Idle switch (TPS)" [digital_in] is wired to M800-A-17 "Analog Voltage Input 4" [analog_in]. Analog and digital on one net. A switch on an analog input works with a pull-up and a threshold; an analog sensor on a digital input loses its value. |
| warn | NO_FUEL_PUMP | fuel pump | This engine harness has no fuel-pump control path: no fuel-pump relay output is wired to the new ECU. If the stock car switches the pump outside the ECU (an airflow-meter contact or a separate module), the standalone must drive the pump relay itself — see the install notes for this car. |
| info | NET_FAMILY | OEM-1-E ↔ M800-A-18 | OEM-1-E "Malfunction indicator lamp (MIL)" [low_side_out] is wired to M800-A-18 "AUX1" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-2-I ↔ M800-A-1 | OEM-2-I "Tachometer output" [tacho_out] is wired to M800-A-1 "AUX2" [switch_out]. Frequency output on a general output: set it up as a tacho/frequency output with the right pull-up. |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-1-A | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-09. Review every wire against both manuals before building. Open items: - Fuel-pump control: MoTeC M800 needs to drive the fuel pump, but the stock ECU has no fuel-pump output (an airflow-meter contact or a separate module runs it). Add a fuel-pump relay on a spare low-side output — see the install notes for this car. Not wired: - OEM-1 A: Constant +12V: MoTeC M800 has no battery-constant input; not needed
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | Link G4X MX5X install manual (NA 1.6/1.8) | https://linkecu.com/documentation/MX5X.pdf | archive | 2026-10-05 | b7f730de9f6e |
| 4 | vendor_doc | MoTeC M400/M600/M800/M880 Manual — Appendix L: Pin list by Function | https://starracecars.com/wp-content/uploads/resources/M400_M600_M800_M880_Manual_A5.pdf | archive | 2026-10-05 | b69bb8ffb674 |
| 4 | vendor_doc | MoTeC M800 OEM WRX56 Installation | https://motec.com.au | archive | 2026-10-05 | 2ca4be92bb65 |
| 2 | community_copy | 1991 Mazda Miata wiring diagrams (Mitchell reproduction, mellens.net community mirror) | https://trull.org/alex/pubmirror/www.mellens.net/mazda/Mazda-Miata-1991-1993/1991_wiring.pdf | — | 2026-10-08 | 6f957a38ed49 |
| 2 | expert_report | Justin Barrera — Miata NA/NB wiring corrections | — | — | — | — |