AP2 2006–09 (F22C1, DBW) → DTAFast T2i (auto)
AP2 2006–09 (F22C1, DBW) — DTAFast — T2i
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-11
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 9: read the Findings page before cutting any wire |
| Size of the job | 45 wires · 11 connectors · 7 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Terminals | 3-1447221-4 |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-A-2 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-A-3 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | T2I-C1-31 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-A-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-A-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-A-8 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-A-9 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-E-3 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | T2I-C1-13 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | SP-GND-1 | T2I-C1-14 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-A-23 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-A-24 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-E-4 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | TB-J-GND | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | SP-0V-1 | T2I-C1-28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | SP-0V-1 | T2I-C1-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-A-20 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-A-21 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-E-5 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | TB-J-VCC | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | SP-5V1-1 | T2I-C1-27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-A-7 | T2I-C1-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-A-6 | T2I-C1-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-A-16 | T2I-C1-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-A-15 | T2I-C1-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-E-17 | T2I-C1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-E-7 | T2I-C1-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-B-6 | RLY1-R-OUT | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | SP-14V-1 | RLY1-R-IN | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | SP-14V-1 | RLY1-R-COIL+ | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | RLY1-R-COIL- | T2I-C1-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-A-30 | T2I-C1-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-A-25 | T2I-C1-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-A-26 | T2I-C1-23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-B-8 | T2I-C1-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | TB-J-TPS1 | T2I-C1-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | TB-J-TPS2 | T2I-C1-33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-D-15 | T2I-C1-26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-E-12 | T2I-C1-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-E-20 | T2I-C1-34 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-E-1 | T2I-C1-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-A-18 | T2I-C1-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-B-11 | T2I-C1-30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-E-11 | T2I-C1-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-E-24 | T2I-C1-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | RLY1-R-COIL+ | T2I-C1-13 | open (OL) | +12 V supply must not touch power ground | |
| 2 | RLY1-R-COIL+ | T2I-C1-28 | open (OL) | +12 V supply must not touch sensor ground | |
| 3 | T2I-C1-27 | T2I-C1-28 | open (OL) | 5 V sensor reference must not touch sensor ground | |
| 4 | RLY1-R-COIL+ | T2I-C1-27 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 5 | T2I-C1-13 | RLY1-R-OUT | open (OL) | power ground must not touch +12 V supply | |
| 6 | T2I-C1-13 | T2I-C1-27 | open (OL) | power ground must not touch 5 V sensor reference | |
| 7 | T2I-C1-27 | RLY1-R-OUT | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 8 | T2I-C1-28 | RLY1-R-OUT | open (OL) | sensor ground must not touch +12 V supply |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
OEM-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Knock sensor | — | — | — | — | — | — | — | — |
| 2 | Ignition power 2 | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 3 | Ignition power 1 | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 4 | Power ground 2 | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | Power ground 1 | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Cam position sensor (T2) | — | W23 | — | 0.5 | T2I-C1-12 | — | — | — |
| 7 | Crank position sensor (T1) | — | W22 | — | 0.5 | T2I-C1-19 | — | — | — |
| 8 | Logic ground 2 | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 9 | Logic ground 1 | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 10 | A/F sensor heater | — | — | — | — | — | — | — | — |
| 11 | Unused cavity | — | — | — | — | — | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Ignition coil 4 | — | — | — | — | — | — | — | — |
| 14 | Ignition coil 3 | — | — | — | — | — | — | — | — |
| 15 | Ignition coil 2 | — | W25 | — | 0.5 | T2I-C1-6 | — | — | — |
| 16 | Ignition coil 1 | — | W24 | — | 0.5 | T2I-C1-3 | — | — | — |
| 17 | Unused cavity | — | — | — | — | — | — | — | — |
| 18 | Vehicle speed sensor | — | W42 | — | 0.5 | T2I-C1-11 | — | — | — |
| 19 | Unused cavity | — | — | — | — | — | — | — | — |
| 20 | Sensor voltage 2 | — | W17 | — | 0.5 | SP-5V1-1 | — | — | — |
| 21 | Sensor voltage 1 | — | W18 | — | 0.5 | SP-5V1-1 | — | — | — |
| 22 | Unused cavity | — | — | — | — | — | — | — | — |
| 23 | Sensor ground 2 | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | Sensor ground 1 | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| 25 | Accelerator pedal position B | — | W33 | — | 0.5 | T2I-C1-22 | — | — | — |
| 26 | Accelerator pedal position A | — | W34 | — | 0.5 | T2I-C1-23 | — | — | — |
| 27 | Unused cavity | — | — | — | — | — | — | — | — |
| 28 | A/F sensor signal − | — | — | — | — | — | — | — | — |
| 29 | Unused cavity | — | — | — | — | — | — | — | — |
| 30 | MAP sensor | — | W32 | — | 0.5 | T2I-C1-20 | — | — | — |
| 31 | A/F sensor signal + | — | — | — | — | — | — | — | — |
OEM-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Unused cavity | — | — | — | — | — | — | — | — |
| 2 | Injector 4 | — | — | — | — | — | — | — | — |
| 3 | Injector 3 | — | — | — | — | — | — | — | — |
| 4 | Injector 2 | — | — | — | — | — | — | — | — |
| 5 | Injector 1 | — | — | — | — | — | — | — | — |
| 6 | VTEC solenoid | — | W28 | — | 0.5 | RLY1-R-OUT | — | — | — |
| 7 | Unused cavity | — | — | — | — | — | — | — | — |
| 8 | Coolant temp sensor | — | W35 | — | 0.5 | T2I-C1-24 | — | — | — |
| 9 | Unused cavity | — | — | — | — | — | — | — | — |
| 10 | Alternator L signal | — | — | — | — | — | — | — | — |
| 11 | VTEC oil pressure switch | — | W43 | — | 0.5 | T2I-C1-30 | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Alternator FR signal | — | — | — | — | — | — | — | — |
| 14 | Unused cavity | — | — | — | — | — | — | — | — |
| 15 | Engine mount control solenoid | — | — | — | — | — | — | — | — |
| 16 | Unused cavity | — | — | — | — | — | — | — | — |
| 17 | Intake air temp sensor | — | — | — | — | — | — | — | — |
| 18 | Alternator control | — | — | — | — | — | — | — | — |
| 19 | Throttle actuator command to throttle control module (SEFD) | — | — | — | — | — | — | — | — |
| 20 | Throttle actuator command to throttle control module (SEDF) | — | — | — | — | — | — | — | — |
| 21 | Evap canister purge valve | — | — | — | — | — | — | — | — |
| 22 | Unused cavity | — | — | — | — | — | — | — | — |
| 23 | Unused cavity | — | — | — | — | — | — | — | — |
| 24 | Unused cavity | — | — | — | — | — | — | — | — |
OEM-D
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Cruise set switch | — | — | — | — | — | — | — | — |
| 2 | Unused cavity | — | — | — | — | — | — | — | — |
| 3 | Unused cavity | — | — | — | — | — | — | — | — |
| 4 | Cruise main switch | — | — | — | — | — | — | — | — |
| 5 | Unused cavity | — | — | — | — | — | — | — | — |
| 6 | Unused cavity | — | — | — | — | — | — | — | — |
| 7 | Cruise resume switch | — | — | — | — | — | — | — | — |
| 8 | Brake pedal position switch | — | — | — | — | — | — | — | — |
| 9 | Cruise clutch signal | — | — | — | — | — | — | — | — |
| 10 | Unused cavity | — | — | — | — | — | — | — | — |
| 11 | Unused cavity | — | — | — | — | — | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Unused cavity | — | — | — | — | — | — | — | — |
| 14 | Unused cavity | — | — | — | — | — | — | — | — |
| 15 | Throttle actuator relay | — | W38 | — | 0.5 | T2I-C1-26 | — | — | — |
| 16 | Unused cavity | — | — | — | — | — | — | — | — |
| 17 | Unused cavity | — | — | — | — | — | — | — | — |
OEM-E
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Coolant temp sensor 2 | — | W41 | — | 0.5 | T2I-C1-32 | — | — | — |
| 2 | Unused cavity | — | — | — | — | — | — | — | — |
| 3 | Logic ground 3 | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 4 | Sensor ground 3 | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 5 | Sensor voltage 3 | — | W19 | — | 0.5 | SP-5V1-1 | — | — | — |
| 6 | Unused cavity | — | — | — | — | — | — | — | — |
| 7 | Main relay control | — | W27 | — | 0.5 | T2I-C1-10 | — | — | — |
| 8 | A/F sensor heater relay | — | — | — | — | — | — | — | — |
| 9 | Ignition signal | — | — | — | — | — | — | — | — |
| 10 | Unused cavity | — | — | — | — | — | — | — | — |
| 11 | CAN H | — | W44 | — | 0.5 | T2I-C1-16 | — | — | — |
| 12 | Radiator fan control | — | W39 | — | 0.5 | T2I-C1-15 | — | — | — |
| 13 | Multiplex communication | — | — | — | — | — | — | — | — |
| 14 | Fuel tank pressure sensor | — | — | — | — | — | — | — | — |
| 15 | Electrical load detector | — | — | — | — | — | — | — | — |
| 16 | Power steering load detector | — | — | — | — | — | — | — | — |
| 17 | Fuel pump relay | — | W26 | — | 0.5 | T2I-C1-1 | — | — | — |
| 18 | A/C clutch relay | — | — | — | — | — | — | — | — |
| 19 | Evap canister vent shut valve | — | — | — | — | — | — | — | — |
| 20 | Secondary O2 sensor | — | W40 | — | 0.5 | T2I-C1-34 | — | — | — |
| 21 | Secondary O2 heater | — | — | — | — | — | — | — | — |
| 22 | Brake pedal switch | — | — | — | — | — | — | — | — |
| 23 | Unused cavity | — | — | — | — | — | — | — | — |
| 24 | CAN L | — | W45 | — | 0.5 | T2I-C1-17 | — | — | — |
| 25 | Engine speed pulse (tacho) | — | — | — | — | — | — | — | — |
| 26 | Vehicle speed output | — | — | — | — | — | — | — | — |
| 27 | Immobilizer code | — | — | — | — | — | — | — | — |
| 28 | A/C switch signal | — | — | — | — | — | — | — | — |
| 29 | Service check signal | — | — | — | — | — | — | — | — |
| 30 | Write enable signal | — | — | — | — | — | — | — | — |
| 31 | Unused cavity | — | — | — | — | — | — | — | — |
RLY1-R
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| COIL+ | Relay coil positive (switched +12 V) | — | W30 | — | 0.5 | SP-14V-1 | — | — | — |
| COIL- | Relay coil negative (ECU low-side driver) | — | W31 | — | 0.5 | T2I-C1-18 | — | — | — |
| IN | Relay contact input (switched +12 V) | — | W29 | — | 0.5 | SP-14V-1 | — | — | — |
| OUT | Relay contact output (switched +12 V to load) | — | W28 | — | 0.5 | OEM-B-6 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W11 | — | 0.5 | OEM-A-23 | — | — | — |
| 1 | — | — | W12 | — | 0.5 | OEM-A-24 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | OEM-E-4 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | TB-J-GND | — | — | — |
| 1 | — | — | W15 | — | 0.5 | T2I-C1-28 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | T2I-C1-29 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W29 | — | 0.5 | RLY1-R-IN | — | — | — |
| 1 | — | — | W1 | — | 0.85 | OEM-A-2 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-A-3 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | T2I-C1-31 | — | — | — |
| 1 | — | — | W30 | — | 0.5 | RLY1-R-COIL+ | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W20 | — | 0.5 | TB-J-VCC | — | — | — |
| 1 | — | — | W21 | — | 0.5 | T2I-C1-27 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | OEM-A-21 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | OEM-A-20 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | OEM-E-5 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W8 | — | 0.85 | OEM-E-3 | — | — | — |
| 1 | — | — | W10 | — | 0.85 | T2I-C1-14 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | T2I-C1-13 | — | — | — |
| 1 | — | — | W4 | — | 0.85 | OEM-A-4 | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-A-5 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-A-8 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-A-9 | — | — | — |
T2I-C1
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | PWM 1 | — | W26 | — | 0.5 | OEM-E-17 | — | — | — |
| 2 | Lambda Nernst Voltage | — | — | — | — | — | — | — | — |
| 3 | Coil 1 | — | W24 | — | 0.5 | OEM-A-16 | — | — | — |
| 4 | Lambda VGND | — | — | — | — | — | — | — | — |
| 5 | Lambda Pump Current | — | — | — | — | — | — | — | — |
| 6 | Coil 2 | — | W25 | — | 0.5 | OEM-A-15 | — | — | — |
| 7 | Lambda Trim Resistor | — | — | — | — | — | — | — | — |
| 8 | — | — | — | — | — | — | — | — | — |
| 9 | — | — | — | — | — | — | — | — | — |
| 10 | PWM 2 | — | W27 | — | 0.5 | OEM-E-7 | — | — | — |
| 11 | Digital 1 | — | W42 | — | 0.5 | OEM-A-18 | — | — | — |
| 12 | Wheel 1 | — | W23 | — | 0.5 | OEM-A-6 | — | — | — |
| 13 | Power Ground 1 | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 14 | Power Ground 2 | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 15 | Lambda Heater Negative | — | W39 | — | 0.5 | OEM-E-12 | — | — | — |
| 16 | CAN High | — | W44 | — | 0.5 | OEM-E-11 | — | — | — |
| 17 | CAN Low | — | W45 | — | 0.5 | OEM-E-24 | — | — | — |
| 18 | PWM 3 | — | W31 | — | 0.5 | RLY1-R-COIL- | — | — | — |
| 19 | Crank | — | W22 | — | 0.5 | OEM-A-7 | — | — | — |
| 20 | Analogue 1 | — | W32 | — | 0.5 | OEM-A-30 | — | — | — |
| 21 | Permanent 12v | — | — | — | — | — | — | — | — |
| 22 | Analogue 2 | — | W33 | — | 0.5 | OEM-A-25 | — | — | — |
| 23 | Analogue 3 | — | W34 | — | 0.5 | OEM-A-26 | — | — | — |
| 24 | Thermistor 1 | — | W35 | — | 0.5 | OEM-B-8 | — | — | — |
| 25 | Analogue 4 | — | W36 | — | 0.5 | TB-J-TPS1 | — | — | — |
| 26 | PWM 4 | — | W38 | — | 0.5 | OEM-D-15 | — | — | — |
| 27 | 5v Output | — | W21 | — | 0.5 | SP-5V1-1 | — | — | — |
| 28 | Sensor Ground | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 29 | Sensor Ground | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 30 | Digital 2 | — | W43 | — | 0.5 | OEM-B-11 | — | — | — |
| 31 | Ignition 12v In | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 32 | Thermistor 2 | — | W41 | — | 0.5 | OEM-E-1 | — | — | — |
| 33 | Analogue 5 | — | W37 | — | 0.5 | TB-J-TPS2 | — | — | — |
| 34 | Analogue 6 | — | W40 | — | 0.5 | OEM-E-20 | — | — | — |
TB-J
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| TPS1 | Throttle position 1 | — | W36 | — | 0.5 | T2I-C1-25 | — | — | — |
| VCC | Throttle sensor 5V supply | — | W20 | — | 0.5 | SP-5V1-1 | — | — | — |
| TPS2 | Throttle position 2 | — | W37 | — | 0.5 | T2I-C1-33 | — | — | — |
| GND | Throttle sensor ground | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| M- | Throttle motor − | — | — | — | — | — | — | — | — |
| M+ | Throttle motor + | — | — | — | — | — | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-A-1 | Knock sensor | knock_in | — | — | — | single_source | |
| OEM-A-10 | A/F sensor heater | low_side_out | — | — | — | single_source | |
| OEM-A-11 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-12 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-13 | Ignition coil 4 | ignition_out | — | — | — | single_source | |
| OEM-A-14 | Ignition coil 3 | ignition_out | — | — | — | single_source | |
| OEM-A-15 | Ignition coil 2 | ignition_out | T2I-C1-6 | Coil 2 | ignition_out | single_source | |
| OEM-A-16 | Ignition coil 1 | ignition_out | T2I-C1-3 | Coil 1 | ignition_out | single_source | |
| OEM-A-17 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-18 | Vehicle speed sensor | digital_in | T2I-C1-11 | Digital 1 | digital_in | single_source | |
| OEM-A-19 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-2 | Ignition power 2 | power_in | RLY1-R-COIL+ + RLY1-R-IN + T2I-C1-31 | Relay coil positive (switched +12 V) + Relay contact input (switched +12 V) + Ignition 12v In | power_in + power_out | single_source | |
| OEM-A-20 | Sensor voltage 2 | vref | T2I-C1-27 + TB-J-VCC | 5v Output + Throttle sensor 5V supply | power_in + vref | corroborated | |
| OEM-A-21 | Sensor voltage 1 | vref | T2I-C1-27 + TB-J-VCC | 5v Output + Throttle sensor 5V supply | power_in + vref | single_source | |
| OEM-A-22 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-23 | Sensor ground 2 | sensor_ground | T2I-C1-28 + T2I-C1-29 + TB-J-GND | Sensor Ground + Sensor Ground + Throttle sensor ground | sensor_ground | corroborated | |
| OEM-A-24 | Sensor ground 1 | sensor_ground | T2I-C1-28 + T2I-C1-29 + TB-J-GND | Sensor Ground + Sensor Ground + Throttle sensor ground | sensor_ground | single_source | |
| OEM-A-25 | Accelerator pedal position B | analog_in | T2I-C1-22 | Analogue 2 | analog_in | corroborated | |
| OEM-A-26 | Accelerator pedal position A | analog_in | T2I-C1-23 | Analogue 3 | analog_in | corroborated | |
| OEM-A-27 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-28 | A/F sensor signal − | — | — | — | — | single_source | |
| OEM-A-29 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-3 | Ignition power 1 | power_in | RLY1-R-COIL+ + RLY1-R-IN + T2I-C1-31 | Relay coil positive (switched +12 V) + Relay contact input (switched +12 V) + Ignition 12v In | power_in + power_out | single_source | |
| OEM-A-30 | MAP sensor | analog_in | T2I-C1-20 | Analogue 1 | analog_in | single_source | |
| OEM-A-31 | A/F sensor signal + | — | — | — | — | single_source | |
| OEM-A-4 | Power ground 2 | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-A-5 | Power ground 1 | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-A-6 | Cam position sensor (T2) | trigger_in | T2I-C1-12 | Wheel 1 | digital_in | single_source | |
| OEM-A-7 | Crank position sensor (T1) | trigger_in | T2I-C1-19 | Crank | trigger_in | single_source | |
| OEM-A-8 | Logic ground 2 | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-A-9 | Logic ground 1 | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-B-1 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-10 | Alternator L signal | — | — | — | — | single_source | |
| OEM-B-11 | VTEC oil pressure switch | digital_in | T2I-C1-30 | Digital 2 | digital_in | single_source | |
| OEM-B-12 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-13 | Alternator FR signal | analog_in | — | — | — | single_source | |
| OEM-B-14 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-15 | Engine mount control solenoid | low_side_out | — | — | — | single_source | |
| OEM-B-16 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-17 | Intake air temp sensor | temp_in | — | — | — | single_source | |
| OEM-B-18 | Alternator control | low_side_out | — | — | — | single_source | |
| OEM-B-19 | Throttle actuator command to throttle control module (SEFD) | — | — | — | — | conflict | |
| OEM-B-2 | Injector 4 | injector_out | — | — | — | single_source | |
| OEM-B-20 | Throttle actuator command to throttle control module (SEDF) | — | — | — | — | conflict | |
| OEM-B-21 | Evap canister purge valve | low_side_out | — | — | — | single_source | |
| OEM-B-22 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-23 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-24 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-3 | Injector 3 | injector_out | — | — | — | single_source | |
| OEM-B-4 | Injector 2 | injector_out | — | — | — | single_source | |
| OEM-B-5 | Injector 1 | injector_out | — | — | — | single_source | |
| OEM-B-6 | VTEC solenoid | high_side_out | RLY1-R-OUT | Relay contact output (switched +12 V to load) | power_out | single_source | |
| OEM-B-7 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-8 | Coolant temp sensor | temp_in | T2I-C1-24 | Thermistor 1 | temp_in | single_source | |
| OEM-B-9 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-1 | Cruise set switch | digital_in | — | — | — | single_source | |
| OEM-D-10 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-11 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-12 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-13 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-14 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-15 | Throttle actuator relay | low_side_out | T2I-C1-26 | PWM 4 | low_side_out | single_source | |
| OEM-D-16 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-17 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-2 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-3 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-4 | Cruise main switch | digital_in | — | — | — | single_source | |
| OEM-D-5 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-6 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-7 | Cruise resume switch | digital_in | — | — | — | single_source | |
| OEM-D-8 | Brake pedal position switch | digital_in | — | — | — | single_source | |
| OEM-D-9 | Cruise clutch signal | digital_in | — | — | — | single_source | |
| OEM-E-1 | Coolant temp sensor 2 | temp_in | T2I-C1-32 | Thermistor 2 | temp_in | single_source | |
| OEM-E-10 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-11 | CAN H | can_h | T2I-C1-16 | CAN High | can_h | single_source | |
| OEM-E-12 | Radiator fan control | low_side_out | T2I-C1-15 | Lambda Heater Negative | low_side_out | single_source | |
| OEM-E-13 | Multiplex communication | serial | — | — | — | single_source | |
| OEM-E-14 | Fuel tank pressure sensor | analog_in | — | — | — | single_source | |
| OEM-E-15 | Electrical load detector | analog_in | — | — | — | single_source | |
| OEM-E-16 | Power steering load detector | analog_in | — | — | — | corroborated | |
| OEM-E-17 | Fuel pump relay | low_side_out | T2I-C1-1 | PWM 1 | low_side_out | single_source | |
| OEM-E-18 | A/C clutch relay | low_side_out | — | — | — | single_source | |
| OEM-E-19 | Evap canister vent shut valve | low_side_out | — | — | — | single_source | |
| OEM-E-2 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-20 | Secondary O2 sensor | lambda_nb_in | T2I-C1-34 | Analogue 6 | analog_in | single_source | |
| OEM-E-21 | Secondary O2 heater | low_side_out | — | — | — | single_source | |
| OEM-E-22 | Brake pedal switch | digital_in | — | — | — | single_source | |
| OEM-E-23 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-24 | CAN L | can_l | T2I-C1-17 | CAN Low | can_l | single_source | |
| OEM-E-25 | Engine speed pulse (tacho) | tacho_out | — | — | — | single_source | |
| OEM-E-26 | Vehicle speed output | tacho_out | — | — | — | single_source | |
| OEM-E-27 | Immobilizer code | — | — | — | — | single_source | |
| OEM-E-28 | A/C switch signal | digital_in | — | — | — | single_source | |
| OEM-E-29 | Service check signal | — | — | — | — | single_source | |
| OEM-E-3 | Logic ground 3 | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-E-30 | Write enable signal | — | — | — | — | single_source | |
| OEM-E-31 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-4 | Sensor ground 3 | sensor_ground | T2I-C1-28 + T2I-C1-29 + TB-J-GND | Sensor Ground + Sensor Ground + Throttle sensor ground | sensor_ground | corroborated | |
| OEM-E-5 | Sensor voltage 3 | vref | T2I-C1-27 + TB-J-VCC | 5v Output + Throttle sensor 5V supply | power_in + vref | corroborated | |
| OEM-E-6 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-7 | Main relay control | low_side_out | T2I-C1-10 | PWM 2 | low_side_out | single_source | |
| OEM-E-8 | A/F sensor heater relay | low_side_out | — | — | — | single_source | |
| OEM-E-9 | Ignition signal | digital_in | — | — | — | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-A-2 | SP-14V-1 | 0.85 | no route | Ignition power 2 | — | |
| W2 | OEM-A-3 | SP-14V-1 | 0.85 | no route | Ignition power 1 | — | |
| W3 | SP-14V-1 | T2I-C1-31 | 0.85 | no route | Ignition 12v In | — | |
| W4 | OEM-A-4 | SP-GND-1 | 0.85 | no route | Power ground 2 | — | |
| W5 | OEM-A-5 | SP-GND-1 | 0.85 | no route | Power ground 1 | — | |
| W6 | OEM-A-8 | SP-GND-1 | 0.85 | no route | Logic ground 2 | — | |
| W7 | OEM-A-9 | SP-GND-1 | 0.85 | no route | Logic ground 1 | — | |
| W8 | OEM-E-3 | SP-GND-1 | 0.85 | no route | Logic ground 3 | — | |
| W9 | SP-GND-1 | T2I-C1-13 | 0.85 | no route | Power Ground 1 | — | |
| W10 | SP-GND-1 | T2I-C1-14 | 0.85 | no route | Power Ground 2 | — | |
| W11 | OEM-A-23 | SP-0V-1 | 0.5 | no route | Sensor ground 2 | — | |
| W12 | OEM-A-24 | SP-0V-1 | 0.5 | no route | Sensor ground 1 | — | |
| W13 | OEM-E-4 | SP-0V-1 | 0.5 | no route | Sensor ground 3 | — | |
| W14 | TB-J-GND | SP-0V-1 | 0.5 | no route | Throttle sensor ground | — | |
| W15 | SP-0V-1 | T2I-C1-28 | 0.5 | no route | Sensor Ground | — | |
| W16 | SP-0V-1 | T2I-C1-29 | 0.5 | no route | Sensor Ground | — | |
| W17 | OEM-A-20 | SP-5V1-1 | 0.5 | no route | Sensor voltage 2 | — | |
| W18 | OEM-A-21 | SP-5V1-1 | 0.5 | no route | Sensor voltage 1 | — | |
| W19 | OEM-E-5 | SP-5V1-1 | 0.5 | no route | Sensor voltage 3 | — | |
| W20 | TB-J-VCC | SP-5V1-1 | 0.5 | no route | Throttle sensor 5V supply | — | |
| W21 | SP-5V1-1 | T2I-C1-27 | 0.5 | no route | 5v Output | — | |
| W22 | OEM-A-7 | T2I-C1-19 | 0.5 | no route | Crank position sensor (T1) | — | |
| W23 | OEM-A-6 | T2I-C1-12 | 0.5 | no route | Cam position sensor (T2) | — | |
| W24 | OEM-A-16 | T2I-C1-3 | 0.5 | no route | Ignition coil 1 | — | |
| W25 | OEM-A-15 | T2I-C1-6 | 0.5 | no route | Ignition coil 2 | — | |
| W26 | OEM-E-17 | T2I-C1-1 | 0.5 | no route | Fuel pump relay | — | |
| W27 | OEM-E-7 | T2I-C1-10 | 0.5 | no route | Main relay control | — | |
| W28 | OEM-B-6 | RLY1-R-OUT | 0.5 | no route | VTEC solenoid | — | |
| W29 | SP-14V-1 | RLY1-R-IN | 0.5 | no route | Relay contact input (switched +12 V) | — | |
| W30 | SP-14V-1 | RLY1-R-COIL+ | 0.5 | no route | Relay coil positive (switched +12 V) | — | |
| W31 | RLY1-R-COIL- | T2I-C1-18 | 0.5 | no route | Relay coil negative (ECU low-side driver) | — | |
| W32 | OEM-A-30 | T2I-C1-20 | 0.5 | no route | MAP sensor | — | |
| W33 | OEM-A-25 | T2I-C1-22 | 0.5 | no route | Accelerator pedal position B | — | |
| W34 | OEM-A-26 | T2I-C1-23 | 0.5 | no route | Accelerator pedal position A | — | |
| W35 | OEM-B-8 | T2I-C1-24 | 0.5 | no route | Coolant temp sensor | — | |
| W36 | TB-J-TPS1 | T2I-C1-25 | 0.5 | no route | Throttle position 1 | — | |
| W37 | TB-J-TPS2 | T2I-C1-33 | 0.5 | no route | Throttle position 2 | — | |
| W38 | OEM-D-15 | T2I-C1-26 | 0.5 | no route | Throttle actuator relay | — | |
| W39 | OEM-E-12 | T2I-C1-15 | 0.5 | no route | Radiator fan control | — | |
| W40 | OEM-E-20 | T2I-C1-34 | 0.5 | no route | Secondary O2 sensor | — | |
| W41 | OEM-E-1 | T2I-C1-32 | 0.5 | no route | Coolant temp sensor 2 | — | |
| W42 | OEM-A-18 | T2I-C1-11 | 0.5 | no route | Vehicle speed sensor | — | |
| W43 | OEM-B-11 | T2I-C1-30 | 0.5 | no route | VTEC oil pressure switch | — | |
| W44 | OEM-E-11 | T2I-C1-16 | 0.5 | no route | CAN H | — | |
| W45 | OEM-E-24 | T2I-C1-17 | 0.5 | no route | CAN L | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 4-1437290-0 | TE | Superseal 1.0 34-way plug, Key 1 | 1.000 | ea |
| connector | S2K-0609-ECU-A | Honda | S2000 2006–09 ECU plug A (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-B | Honda | S2000 2006–09 ECU plug B (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-D | Honda | S2000 2006–09 ECU plug D (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-E | Honda | S2000 2006–09 ECU plug E (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-TB | Honda | 2006–09 S2000 throttle body plug, 6-way (pin numbers from Link forum dealer post; housing P/N unknown) | 1.000 | ea |
| terminal | 3-1447221-4 | TE | Superseal 1.0 socket terminal, 20 AWG (0.5 sq mm) | 27.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| dbw_motor | TB | Throttle motor + | — | — | — | — | — |
| dbw_motor | TB | Throttle motor − | — | — | — | — | — |
| dbw_tps | TB | Throttle position 1 | 0_5v | T2I-C1-25 | Analogue 4 | analog_0_5 | — |
| dbw_tps | TB | Throttle position 2 | 0_5v | T2I-C1-33 | Analogue 5 | analog_0_5 | — |
Findings
Open (16)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | PHYS_REQUIRED_OPEN | T2I-C1-21 | T2I-C1-21 "Permanent 12v" is required but not wired. |
| error | PHYS_REQUIRED_OPEN | TB-J-M+ | TB-J-M+ "Throttle motor +" is required but not wired. |
| error | PHYS_REQUIRED_OPEN | TB-J-M- | TB-J-M- "Throttle motor −" is required but not wired. |
| error | REQUIRED_UNMAPPED | OEM-A-13 | Required OEM function "Ignition coil 4" (ignition_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-A-14 | Required OEM function "Ignition coil 3" (ignition_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-B-2 | Required OEM function "Injector 4" (injector_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-B-3 | Required OEM function "Injector 3" (injector_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-B-4 | Required OEM function "Injector 2" (injector_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-B-5 | Required OEM function "Injector 1" (injector_out) is not connected to the new ECU. |
| warn | DATASET_GAP | T2i C1 | 2 of 34 cavities on T2i C1 have no pin data (8,9). Anything there is invisible to these checks. |
| warn | DBW_SHARED_5V | OEM-A-20 + OEM-A-21 + OEM-E-5 + SP-5V1-1 + T2I-C1-27 + TB-J-VCC | These 5 V supplies are separate in the stock car (OEM-A-20 [s2k_vcc2], OEM-A-21 [s2k_vcc1], OEM-E-5 [s2k_vcc3]) and here share one ECU 5 V (T2I-C1-27). On a drive-by-wire car the OEM splits them so one short or fault can't corrupt both throttle/pedal tracks at once. T2i has 1 5 V sensor supply pin(s). All are in use, so decide: accept the shared supply (and rely on the ECU's DBW fault checks), or add a separate regulated 5 V for the sub tracks. |
| warn | LOAD_UNKNOWN | RLY1-R-OUT | RLY1-R-OUT "Relay contact output (switched +12 V to load)" drives OEM-B-6 VTEC solenoid (load 1.0 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | T2I-C1-15 | T2I-C1-15 "Lambda Heater Negative" drives OEM-E-12 Radiator fan control (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | NET_FAMILY | OEM-A-6 ↔ T2I-C1-12 | OEM-A-6 "Cam position sensor (T2)" [trigger_in] is wired to T2I-C1-12 "Wheel 1" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| warn | SUPPLY_GROUP | OEM-A-20 + OEM-A-21 + OEM-E-5 + SP-5V1-1 + T2I-C1-27 + TB-J-VCC | Supplies meant to stay independent share one net: OEM-A-20 [s2k_vcc2], OEM-A-21 [s2k_vcc1], OEM-E-5 [s2k_vcc3]. The new ECU has no free 5 V reference, so they share one: normal on a standalone, but a short on any of these sensors drops them all. |
| info | UNMAPPED | OEM | 33 optional OEM pins are not mapped: OEM-A-1 Knock sensor; OEM-A-10 A/F sensor heater; OEM-A-28 A/F sensor signal −; OEM-A-31 A/F sensor signal +; OEM-B-10 Alternator L signal; OEM-B-13 Alternator FR signal; OEM-B-15 Engine mount control solenoid; OEM-B-17 Intake air temp sensor; OEM-B-18 Alternator control; OEM-B-19 Throttle actuator command to throttle control module (SEFD); OEM-B-20 Throttle actuator command to throttle control module (SEDF); OEM-B-21 Evap canister purge valve; OEM-D-1 Cruise set switch; OEM-D-4 Cruise main switch; OEM-D-7 Cruise resume switch; OEM-D-8 Brake pedal position switch; OEM-D-9 Cruise clutch signal; OEM-E-13 Multiplex communication; OEM-E-14 Fuel tank pressure sensor; OEM-E-15 Electrical load detector; OEM-E-16 Power steering load detector; OEM-E-18 A/C clutch relay; OEM-E-19 Evap canister vent shut valve; OEM-E-21 Secondary O2 heater; OEM-E-22 Brake pedal switch; OEM-E-25 Engine speed pulse (tacho); OEM-E-26 Vehicle speed output; OEM-E-27 Immobilizer code; OEM-E-28 A/C switch signal; OEM-E-29 Service check signal; OEM-E-30 Write enable signal; OEM-E-8 A/F sensor heater relay; OEM-E-9 Ignition signal |
Accepted (0)
| Code | Subject | Reason | By |
|---|
Notes
Fit check: needs add-on. Resolve these before building: - No drive-by-wire; needs a cable-throttle conversion or an external DBW controller - No knock input; the stock knock sensor would be unused - Only 2 ignition outputs for 4 cylinders: wasted spark (pair coils per firing order) Auto-mapped by auto_map() from the library pin data on 2026-10-11. Review every wire against both manuals before building. Open items: - OEM-A 14: Ignition coil 3: no free ignition output on DTAFast T2i - OEM-A 13: Ignition coil 4: no free ignition output on DTAFast T2i - OEM-B 5: Injector 1: no free injector output on DTAFast T2i - OEM-B 4: Injector 2: no free injector output on DTAFast T2i - OEM-B 3: Injector 3: no free injector output on DTAFast T2i - OEM-B 2: Injector 4: no free injector output on DTAFast T2i - TB-J M+: Throttle motor +: needs a paired H-bridge on DTAFast T2i (H-bridge pairing not in the library: set device_pin.bridge_pair from the ECU manual) - TB-J M-: Throttle motor −: needs a paired H-bridge on DTAFast T2i (H-bridge pairing not in the library: set device_pin.bridge_pair from the ECU manual) - T2I-C1 21: Permanent 12v: required by DTAFast T2i but no stock pin feeds it; wire by hand Not wired: - OEM-A 1: Knock sensor: no free knock input on DTAFast T2i - OEM-E 9: Ignition signal: key-on 12 V sense — optional in a swap (the main relay is energized from keyed 12 V, not from this pin); DTAFast T2i has no dedicated key-on input - OEM-E 18: A/C clutch relay: no free relay_control/low_side/heater_low_side/ls_hs/injector rated ≥ 0.2 A on DTAFast T2i - OEM-E 8: A/F sensor heater relay: no free relay_control/low_side/heater_low_side/ls_hs/injector rated ≥ 0.2 A on DTAFast T2i - OEM-E 21: Secondary O2 heater: no free heater_low_side/low_side/relay_control/ls_hs/injector on DTAFast T2i - OEM-A 10: A/F sensor heater: no free heater_low_side/low_side/relay_control/ls_hs/injector on DTAFast T2i - OEM-B 15: Engine mount control solenoid: no free low_side/relay_control/heater_low_side/ls_hs/injector on DTAFast T2i - OEM-B 18: Alternator control: no free low_side/relay_control/heater_low_side/ls_hs/injector on DTAFast T2i - OEM-B 21: Evap canister purge valve: no free low_side/relay_control/heater_low_side/ls_hs/injector on DTAFast T2i - OEM-E 19: Evap canister vent shut valve: no free low_side/relay_control/heater_low_side/ls_hs/injector on DTAFast T2i - OEM-E 25: Engine speed pulse (tacho): no free tacho/frequency_out/low_side/ls_hs on DTAFast T2i - OEM-E 26: Vehicle speed output: no free frequency_out/tacho/low_side/ls_hs on DTAFast T2i - OEM-B 17: Intake air temp sensor: no free thermistor/analog_0_5 on DTAFast T2i - OEM-B 13: Alternator FR signal: no free analog_0_5 on DTAFast T2i - OEM-E 14: Fuel tank pressure sensor: no free analog_0_5 on DTAFast T2i - OEM-E 15: Electrical load detector: no free analog_0_5 on DTAFast T2i - OEM-E 16: Power steering load detector: no free analog_0_5 on DTAFast T2i - OEM-D 1: Cruise set switch: no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-D 4: Cruise main switch: no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-D 7: Cruise resume switch: no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-D 8: Brake pedal position switch: no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-D 9: Cruise clutch signal: no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-E 22: Brake pedal switch: no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-E 28: A/C switch signal: no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-E 13: Multiplex communication: no free k_line on DTAFast T2i - OEM-A 28: A/F sensor signal −: not classified in the library; wire by hand - OEM-A 31: A/F sensor signal +: not classified in the library; wire by hand - OEM-B 10: Alternator L signal: not classified in the library; wire by hand - OEM-B 19: Throttle actuator command to throttle control module (SEFD): not classified in the library; wire by hand - OEM-B 20: Throttle actuator command to throttle control module (SEDF): not classified in the library; wire by hand - OEM-E 27: Immobilizer code: not classified in the library; wire by hand - OEM-E 29: Service check signal: not classified in the library; wire by hand - OEM-E 30: Write enable signal: not classified in the library; wire by hand
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | AEM 30-6053 Series 2 Plug & Play EMS, 2006–2008 S2000 AP2 (original ECU pinout) | https://documents.aemelectronics.com/techlibrary_30-6053_series_2_plug___play_ems.pdf | — | 2026-10-05 | ecc8006f849f |
| 4 | vendor_doc | Bosch relay catalogue (mini ISO relays) | https://www.bosch-ibusiness.com/media/downloads/kataloge/relay/2025_10_bosch_relay_catalogue.pdf | archive | 2026-10-05 | 20344cff1ef3 |
| 4 | vendor_doc | DTAFast T2i ECU wiring diagram | https://cdn.shopify.com/s/files/1/0848/7508/4108/files/T2i_Wiring-Diagram.pdf?v=1728571341 | — | — | — |
| 4 | community_copy | Honda S2000 Service Manual 2000–2008, Fuel and Emissions Systems | https://www.s2000.wiki/view/images/7/7f/Service_Manual_2000-2008.pdf | archive | 2026-10-05 | a470cfc928e9 |
| 4 | vendor_doc | Omron G8V-RH-1C7T-R-DC12 high-current micro 280 automotive relay datasheet | https://www.alldatasheet.com/datasheet-pdf/pdf/333797/OMRON/G8V-RH-1C7T-R-DC12.html | — | 2026-10-05 | 764a0505a941 |
| 3 | vendor_doc | ScienceofSpeed Link G4X ECU, S2000 2006–09 (product page) | https://www.scienceofspeed.com/s2000-2000-09/scienceofspeed-link-g4x-ecu-s2000-2006-09-enpp-3822.html | archive | 2026-10-05 | 643bc0efd6d7 |
| 2 | forum | Link forum: dbw wiring (07/08 S2000, ViPEC V88) | https://forums.linkecu.com/topic/313-dbw-wiring/ | — | 2026-10-05 | b788a1b47b9e |