Lexus SC400 1998-2000 (1UZ-FE VVT-i) → DTAFast T8+ (auto)
Lexus SC400 1998-2000 (1UZ-FE VVT-i) — DTAFast — T8+
Drawn by Michael Gnankou · Rev 0 · proposal · 2026-10-18
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | proposal · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | none |
| Size of the job | 68 wires · 12 connectors · 2 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Terminals | 3-1447221-4 |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-E15-16 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-E15-7 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | OEM-E15-8 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-E15-1 | T8-C3-26 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | NEW-BATT-1 | T8-C3-27 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-E13-17 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-E14-21 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | SP-GND-1 | T8-C1-13 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | T8-C1-14 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-E13-18 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-E13-19 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | SP-0V-1 | T8-C2-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | SP-0V-1 | T8-C2-33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-E13-2 | T8-C2-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-E14-23 | T8-C2-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-E14-22 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-E14-10 | T8-C2-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-E13-16 | T8-C2-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-E13-24 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-E13-15 | T8-C2-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-E13-23 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-E14-18 | T8-C3-31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-E14-17 | T8-C3-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-E14-11 | T8-C1-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-E14-12 | T8-C1-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-E14-13 | T8-C1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-E14-14 | T8-C1-26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-E14-15 | T8-C1-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-E14-16 | T8-C1-27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-E14-25 | T8-C1-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-E14-26 | T8-C1-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-E13-5 | T8-C1-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-E13-6 | T8-C1-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-E14-1 | T8-C1-34 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-E14-2 | T8-C1-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-E14-3 | T8-C1-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-E14-4 | T8-C1-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-E14-5 | T8-C1-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-E14-6 | T8-C1-23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-E14-7 | T8-C1-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-E14-8 | T8-C1-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-E15-9 | T8-C1-31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-E11-19 | T8-C1-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-E14-20 | T8-C1-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-E13-10 | T8-C2-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-E13-13 | T8-C2-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | OEM-E13-21 | T8-C2-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | OEM-E13-20 | T8-C2-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W49 | OEM-E13-9 | T8-C2-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W50 | OEM-E13-14 | T8-C2-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W51 | OEM-E15-10 | T8-C1-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W52 | OEM-E15-5 | T8-C3-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W53 | OEM-E11-7 | T8-C3-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W54 | OEM-E11-8 | T8-C3-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W55 | OEM-E13-3 | T8-C3-23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W56 | OEM-E13-4 | T8-C3-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W57 | OEM-E11-28 | T8-C3-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W58 | OEM-E12-12 | T8-C3-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W59 | OEM-E13-8 | T8-C3-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W60 | OEM-E14-19 | T8-C3-28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W61 | OEM-E11-18 | T8-C2-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W62 | OEM-E11-27 | T8-C3-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W63 | OEM-E13-11 | T8-C3-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W64 | OEM-E13-12 | T8-C2-34 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W65 | OEM-E13-22 | T8-C2-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W66 | OEM-E14-27 | T8-C2-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W67 | OEM-E14-28 | T8-C2-8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W68 | OEM-E11-17 | T8-C2-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | T8-C1-13 | NEW-BATT-1 | open (OL) | power ground must not touch +12 V supply | |
| 2 | T8-C1-13 | OEM-E15-16 | open (OL) | power ground must not touch +12 V supply | |
| 3 | T8-C1-13 | T8-C1-31 | open (OL) | power ground must not touch +12 V supply | |
| 4 | T8-C1-13 | T8-C2-24 | open (OL) | power ground must not touch 5 V sensor reference | |
| 5 | T8-C1-13 | T8-C3-26 | open (OL) | power ground must not touch +12 V supply | |
| 6 | T8-C2-21 | NEW-BATT-1 | open (OL) | sensor ground must not touch +12 V supply | |
| 7 | T8-C2-21 | OEM-E15-16 | open (OL) | sensor ground must not touch +12 V supply | |
| 8 | T8-C2-21 | T8-C1-31 | open (OL) | sensor ground must not touch +12 V supply | |
| 9 | T8-C2-21 | T8-C2-24 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 10 | T8-C2-21 | T8-C3-26 | open (OL) | sensor ground must not touch +12 V supply | |
| 11 | T8-C2-24 | NEW-BATT-1 | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 12 | T8-C2-24 | OEM-E15-16 | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 13 | T8-C2-24 | T8-C1-31 | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 14 | T8-C2-24 | T8-C3-26 | open (OL) | 5 V sensor reference must not touch +12 V supply |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
NEW-BATT
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W5 | — | 0.85 | T8-C3-27 | — | — | — |
OEM-E11
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 17 | Starter signal (STA) | — | W68 | — | 0.5 | T8-C2-11 | — | — | — |
| 18 | O2 sensor signal (bank unconfirmed) | — | W61 | — | 0.5 | T8-C2-19 | — | — | — |
| 19 | VVT oil-control valve RH (OCR+) | — | W43 | — | 0.5 | T8-C1-5 | — | — | — |
| 27 | O2 sensor signal (bank unconfirmed) | — | W62 | — | 0.5 | T8-C3-17 | — | — | — |
| 28 | VVT oil-control valve RH (OCR−) | — | W57 | — | 0.5 | T8-C3-25 | — | — | — |
| 5 | Diagnostic test (TC) | — | — | — | — | — | — | — | — |
| 7 | O2 sensor heater (bank unconfirmed) | — | W53 | — | 0.5 | T8-C3-9 | — | — | — |
| 8 | O2 sensor heater (bank unconfirmed) | — | W54 | — | 0.5 | T8-C3-3 | — | — | — |
OEM-E12
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 12 | Throttle magnetic clutch + (CL+) | — | W58 | — | 0.5 | T8-C3-10 | — | — | — |
OEM-E13
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | MAF signal (VG) | — | W45 | — | 0.5 | T8-C2-10 | — | — | — |
| 11 | O2 sensor signal (bank unconfirmed) | — | W63 | — | 0.5 | T8-C3-18 | — | — | — |
| 12 | O2 sensor signal (bank unconfirmed) | — | W64 | — | 0.5 | T8-C2-34 | — | — | — |
| 13 | Throttle position sensor 1 (VTA) | — | W46 | — | 0.5 | T8-C2-1 | — | — | — |
| 14 | Engine coolant temp (THW) | — | W50 | — | 0.5 | T8-C2-7 | — | — | — |
| 15 | VVT position sensor RH (VVR+) | — | W20 | — | 0.5 | T8-C2-2 | — | — | — |
| 16 | VVT position sensor LH (VVL+) | — | W18 | — | 0.5 | T8-C2-29 | — | — | — |
| 17 | ECU ground (E1) | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 18 | Sensor ground (E2) | — | W10 | — | 0.5 | SP-0V-1 | — | — | — |
| 19 | MAF ground (EVG) | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| 2 | +5V sensor reference (VC) | — | W14 | — | 0.5 | T8-C2-24 | — | — | — |
| 20 | Throttle position sensor 2 (VTA2) | — | W48 | — | 0.5 | T8-C2-6 | — | — | — |
| 21 | Accelerator pedal position 1 (VPA) | — | W47 | — | 0.5 | T8-C2-5 | — | — | — |
| 22 | Intake air temp (THA) | — | W65 | — | 0.5 | T8-C2-25 | — | — | — |
| 23 | VVT position sensor RH (VVR−) | — | W21 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | VVT position sensor LH (VVL−) | — | W19 | — | 0.5 | SP-0V-1 | — | — | — |
| 3 | O2 sensor heater (bank unconfirmed) | — | W55 | — | 0.5 | T8-C3-23 | — | — | — |
| 4 | O2 sensor heater (bank unconfirmed) | — | W56 | — | 0.5 | T8-C3-24 | — | — | — |
| 5 | Injector 1 (cyl 1) | — | W32 | — | 0.5 | T8-C1-9 | — | — | — |
| 6 | Injector 2 (cyl 2) | — | W33 | — | 0.5 | T8-C1-17 | — | — | — |
| 8 | Throttle magnetic clutch − (CL−) | — | W59 | — | 0.5 | T8-C3-4 | — | — | — |
| 9 | Accelerator pedal position 2 (VPA2) | — | W49 | — | 0.5 | T8-C2-18 | — | — | — |
OEM-E14
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector 3 (cyl 3) | — | W34 | — | 0.5 | T8-C1-34 | — | — | — |
| 10 | Camshaft position sensor (G2) | — | W17 | — | 0.5 | T8-C2-22 | — | — | — |
| 11 | Ignition coil 1 (IGT1) | — | W24 | — | 0.5 | T8-C1-10 | — | — | — |
| 12 | Ignition coil 2 (IGT2) | — | W25 | — | 0.5 | T8-C1-18 | — | — | — |
| 13 | Ignition coil 3 (IGT3) | — | W26 | — | 0.5 | T8-C1-1 | — | — | — |
| 14 | Ignition coil 4 (IGT4) | — | W27 | — | 0.5 | T8-C1-26 | — | — | — |
| 15 | Ignition coil 5 (IGT5) | — | W28 | — | 0.5 | T8-C1-11 | — | — | — |
| 16 | Ignition coil 6 (IGT6) | — | W29 | — | 0.5 | T8-C1-27 | — | — | — |
| 17 | Knock sensor RH (KNKR) | — | W23 | — | 0.5 | T8-C3-32 | — | — | — |
| 18 | Knock sensor LH (KNKL) | — | W22 | — | 0.5 | T8-C3-31 | — | — | — |
| 19 | VVT oil-control valve LH (OCV−) | — | W60 | — | 0.5 | T8-C3-28 | — | — | — |
| 2 | Injector 4 (cyl 4) | — | W35 | — | 0.5 | T8-C1-25 | — | — | — |
| 20 | VVT oil-control valve LH (OCV+) | — | W44 | — | 0.5 | T8-C1-4 | — | — | — |
| 21 | Power/injector ground (E01) | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 22 | Crank position sensor (NE−) | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 23 | Crank position sensor (NE+) | — | W15 | — | 0.5 | T8-C2-12 | — | — | — |
| 25 | Ignition coil 7 (IGT7) | — | W30 | — | 0.5 | T8-C1-12 | — | — | — |
| 26 | Ignition coil 8 (IGT8) | — | W31 | — | 0.5 | T8-C1-19 | — | — | — |
| 27 | Ignition confirmation 1 (IGF1) | — | W66 | — | 0.5 | T8-C2-4 | — | — | — |
| 28 | Ignition confirmation 2 (IGF2) | — | W67 | — | 0.5 | T8-C2-8 | — | — | — |
| 29 | ACIS induction VSV | — | — | — | — | — | — | — | — |
| 3 | Injector 5 (cyl 5) | — | W36 | — | 0.5 | T8-C1-16 | — | — | — |
| 4 | Injector 6 (cyl 6) | — | W37 | — | 0.5 | T8-C1-15 | — | — | — |
| 5 | Injector 7 (cyl 7) | — | W38 | — | 0.5 | T8-C1-24 | — | — | — |
| 6 | Injector 8 (cyl 8) | — | W39 | — | 0.5 | T8-C1-23 | — | — | — |
| 7 | Throttle motor − (M−) | — | W40 | — | 0.5 | T8-C1-7 | — | — | — |
| 8 | Throttle motor + (M+) | — | W41 | — | 0.5 | T8-C1-6 | — | — | — |
OEM-E15
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Battery constant (+12V) | — | W4 | — | 0.85 | T8-C3-26 | — | — | — |
| 10 | EFI main relay control (MREL) | — | W51 | — | 0.5 | T8-C1-3 | — | — | — |
| 11 | OBD-II / DLC3 data (SIL) | — | — | — | — | — | — | — | — |
| 16 | ECM power (EFI relay +B) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 5 | Fuel pump relay control (FC) | — | W52 | — | 0.5 | T8-C3-22 | — | — | — |
| 6 | Check engine light (W) | — | — | — | — | — | — | — | — |
| 7 | ECM power feed (+BM) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 8 | ECM power (EFI relay +B1) | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 9 | Ignition switch (+12V) | — | W42 | — | 0.5 | T8-C1-31 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W19 | — | 0.5 | OEM-E13-24 | — | — | — |
| 1 | — | — | W10 | — | 0.5 | OEM-E13-18 | — | — | — |
| 1 | — | — | W11 | — | 0.5 | OEM-E13-19 | — | — | — |
| 1 | — | — | W12 | — | 0.5 | T8-C2-21 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | T8-C2-33 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-E14-22 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | OEM-E13-23 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-E15-16 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-E15-7 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | OEM-E15-8 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W6 | — | 0.85 | OEM-E13-17 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-E14-21 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | T8-C1-13 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | T8-C1-14 | — | — | — |
T8-C1
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Coil 3 | — | W26 | — | 0.5 | OEM-E14-13 | — | — | — |
| 2 | — | — | — | — | — | — | — | — | — |
| 3 | PWM 3 | — | W51 | — | 0.5 | OEM-E15-10 | — | — | — |
| 4 | PWM 2 | — | W44 | — | 0.5 | OEM-E14-20 | — | — | — |
| 5 | PWM 1 | — | W43 | — | 0.5 | OEM-E11-19 | — | — | — |
| 6 | Motor 1 + | — | W41 | — | 0.5 | OEM-E14-8 | — | — | — |
| 7 | Motor 1 - | — | W40 | — | 0.5 | OEM-E14-7 | — | — | — |
| 8 | — | — | — | — | — | — | — | — | — |
| 9 | Injector 1 | — | W32 | — | 0.5 | OEM-E13-5 | — | — | — |
| 10 | Coil 1 | — | W24 | — | 0.5 | OEM-E14-11 | — | — | — |
| 11 | Coil 5 | — | W28 | — | 0.5 | OEM-E14-15 | — | — | — |
| 12 | Coil 7 | — | W30 | — | 0.5 | OEM-E14-25 | — | — | — |
| 13 | Power Ground 1 | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 14 | Power Ground 2 | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 15 | Injector 6 | — | W37 | — | 0.5 | OEM-E14-4 | — | — | — |
| 16 | Injector 5 | — | W36 | — | 0.5 | OEM-E14-3 | — | — | — |
| 17 | Injector 2 | — | W33 | — | 0.5 | OEM-E13-6 | — | — | — |
| 18 | Coil 2 | — | W25 | — | 0.5 | OEM-E14-12 | — | — | — |
| 19 | Coil 8 | — | W31 | — | 0.5 | OEM-E14-26 | — | — | — |
| 20 | — | — | — | — | — | — | — | — | — |
| 21 | — | — | — | — | — | — | — | — | — |
| 22 | — | — | — | — | — | — | — | — | — |
| 23 | Injector 8 | — | W39 | — | 0.5 | OEM-E14-6 | — | — | — |
| 24 | Injector 7 | — | W38 | — | 0.5 | OEM-E14-5 | — | — | — |
| 25 | Injector 4 | — | W35 | — | 0.5 | OEM-E14-2 | — | — | — |
| 26 | Coil 4 | — | W27 | — | 0.5 | OEM-E14-14 | — | — | — |
| 27 | Coil 6 | — | W29 | — | 0.5 | OEM-E14-16 | — | — | — |
| 28 | — | — | — | — | — | — | — | — | — |
| 29 | — | — | — | — | — | — | — | — | — |
| 30 | — | — | — | — | — | — | — | — | — |
| 31 | Ignition 12v In | — | W42 | — | 0.5 | OEM-E15-9 | — | — | — |
| 32 | — | — | — | — | — | — | — | — | — |
| 33 | — | — | — | — | — | — | — | — | — |
| 34 | Injector 3 | — | W34 | — | 0.5 | OEM-E14-1 | — | — | — |
T8-C2
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Analogue 2 | — | W46 | — | 0.5 | OEM-E13-13 | — | — | — |
| 2 | Wheel 1 | — | W20 | — | 0.5 | OEM-E13-15 | — | — | — |
| 3 | Analogue 10 | — | — | — | — | — | — | — | — |
| 4 | Digital 1 | — | W66 | — | 0.5 | OEM-E14-27 | — | — | — |
| 5 | Analogue 3 | — | W47 | — | 0.5 | OEM-E13-21 | — | — | — |
| 6 | Analogue 4 | — | W48 | — | 0.5 | OEM-E13-20 | — | — | — |
| 7 | Thermistor 1 | — | W50 | — | 0.5 | OEM-E13-14 | — | — | — |
| 8 | Digital 2 | — | W67 | — | 0.5 | OEM-E14-28 | — | — | — |
| 9 | 5v Output | — | — | — | — | — | — | — | — |
| 10 | Analogue 1 | — | W45 | — | 0.5 | OEM-E13-10 | — | — | — |
| 11 | Digital 3 | — | W68 | — | 0.5 | OEM-E11-17 | — | — | — |
| 12 | Crank | — | W15 | — | 0.5 | OEM-E14-23 | — | — | — |
| 13 | Analogue 12 | — | — | — | — | — | — | — | — |
| 14 | Digital 4 | — | — | — | — | — | — | — | — |
| 15 | Digital 5 | — | — | — | — | — | — | — | — |
| 16 | Analogue 11 | — | — | — | — | — | — | — | — |
| 17 | Thermistor 3 | — | — | — | — | — | — | — | — |
| 18 | Analogue 5 | — | W49 | — | 0.5 | OEM-E13-9 | — | — | — |
| 19 | Analogue 6 | — | W61 | — | 0.5 | OEM-E11-18 | — | — | — |
| 20 | Wheel 2 | — | — | — | — | — | — | — | — |
| 21 | Sensor Ground | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | Cam 1 | — | W17 | — | 0.5 | OEM-E14-10 | — | — | — |
| 23 | — | — | — | — | — | — | — | — | — |
| 24 | 5v Output | — | W14 | — | 0.5 | OEM-E13-2 | — | — | — |
| 25 | Thermistor 2 | — | W65 | — | 0.5 | OEM-E13-22 | — | — | — |
| 26 | CAN High | — | — | — | — | — | — | — | — |
| 27 | Digital 6 | — | — | — | — | — | — | — | — |
| 28 | CAN Low | — | — | — | — | — | — | — | — |
| 29 | Cam 2 | — | W18 | — | 0.5 | OEM-E13-16 | — | — | — |
| 30 | — | — | — | — | — | — | — | — | — |
| 31 | Wheel 3 | — | — | — | — | — | — | — | — |
| 32 | Wheel 4 | — | — | — | — | — | — | — | — |
| 33 | Sensor Ground | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 34 | Analogue 9 | — | W64 | — | 0.5 | OEM-E13-12 | — | — | — |
T8-C3
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Lambda 2 Pump Current | — | — | — | — | — | — | — | — |
| 2 | Lambda 2 VGND | — | — | — | — | — | — | — | — |
| 3 | Lambda 2 Heater Negative | — | W54 | — | 0.5 | OEM-E11-8 | — | — | — |
| 4 | PWM 9 | — | W59 | — | 0.5 | OEM-E13-8 | — | — | — |
| 5 | Lambda 2 Trim Resistor | — | — | — | — | — | — | — | — |
| 6 | Lambda 2 Nernst Voltage | — | — | — | — | — | — | — | — |
| 7 | Lambda 1 Pump Current | — | — | — | — | — | — | — | — |
| 8 | Lambda 1 VGND | — | — | — | — | — | — | — | — |
| 9 | Lambda 1 Heater Negative | — | W53 | — | 0.5 | OEM-E11-7 | — | — | — |
| 10 | PWM 8 | — | W58 | — | 0.5 | OEM-E12-12 | — | — | — |
| 11 | Lambda 1 Trim Resistor | — | — | — | — | — | — | — | — |
| 12 | Lambda 1 Nernst Voltage | — | — | — | — | — | — | — | — |
| 13 | — | — | — | — | — | — | — | — | — |
| 14 | — | — | — | — | — | — | — | — | — |
| 15 | — | — | — | — | — | — | — | — | — |
| 16 | — | — | — | — | — | — | — | — | — |
| 17 | Analogue 7 | — | W62 | — | 0.5 | OEM-E11-27 | — | — | — |
| 18 | Analogue 8 | — | W63 | — | 0.5 | OEM-E13-11 | — | — | — |
| 19 | — | — | — | — | — | — | — | — | — |
| 20 | — | — | — | — | — | — | — | — | — |
| 21 | — | — | — | — | — | — | — | — | — |
| 22 | PWM 4 | — | W52 | — | 0.5 | OEM-E15-5 | — | — | — |
| 23 | PWM 5 | — | W55 | — | 0.5 | OEM-E13-3 | — | — | — |
| 24 | PWM 6 | — | W56 | — | 0.5 | OEM-E13-4 | — | — | — |
| 25 | PWM 7 | — | W57 | — | 0.5 | OEM-E11-28 | — | — | — |
| 26 | Permanent 12v | — | W4 | — | 0.85 | OEM-E15-1 | — | — | — |
| 27 | Permanent 12v | — | W5 | — | 0.85 | NEW-BATT-1 | — | — | — |
| 28 | PWM 10 | — | W60 | — | 0.5 | OEM-E14-19 | — | — | — |
| 29 | — | — | — | — | — | — | — | — | — |
| 30 | — | — | — | — | — | — | — | — | — |
| 31 | Knock 1 | — | W22 | — | 0.5 | OEM-E14-18 | — | — | — |
| 32 | Knock 2 | — | W23 | — | 0.5 | OEM-E14-17 | — | — | — |
| 33 | CAN 2 High | — | — | — | — | — | — | — | — |
| 34 | CAN 2 Low | — | — | — | — | — | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-E11-17 | Starter signal (STA) | digital_in | T8-C2-11 | Digital 3 | digital_in | corroborated | |
| OEM-E11-18 | O2 sensor signal (bank unconfirmed) | lambda_nb_in | T8-C2-19 | Analogue 6 | analog_in | corroborated | |
| OEM-E11-19 | VVT oil-control valve RH (OCR+) | low_side_out | T8-C1-5 | PWM 1 | low_side_out | corroborated | |
| OEM-E11-27 | O2 sensor signal (bank unconfirmed) | lambda_nb_in | T8-C3-17 | Analogue 7 | analog_in | corroborated | |
| OEM-E11-28 | VVT oil-control valve RH (OCR−) | low_side_out | T8-C3-25 | PWM 7 | low_side_out | corroborated | |
| OEM-E11-5 | Diagnostic test (TC) | serial | — | — | — | corroborated | |
| OEM-E11-7 | O2 sensor heater (bank unconfirmed) | low_side_out | T8-C3-9 | Lambda 1 Heater Negative | low_side_out | corroborated | |
| OEM-E11-8 | O2 sensor heater (bank unconfirmed) | low_side_out | T8-C3-3 | Lambda 2 Heater Negative | low_side_out | corroborated | |
| OEM-E12-12 | Throttle magnetic clutch + (CL+) | low_side_out | T8-C3-10 | PWM 8 | low_side_out | corroborated | |
| OEM-E13-10 | MAF signal (VG) | analog_in | T8-C2-10 | Analogue 1 | analog_in | corroborated | |
| OEM-E13-11 | O2 sensor signal (bank unconfirmed) | lambda_nb_in | T8-C3-18 | Analogue 8 | analog_in | corroborated | |
| OEM-E13-12 | O2 sensor signal (bank unconfirmed) | lambda_nb_in | T8-C2-34 | Analogue 9 | analog_in | corroborated | |
| OEM-E13-13 | Throttle position sensor 1 (VTA) | analog_in | T8-C2-1 | Analogue 2 | analog_in | corroborated | |
| OEM-E13-14 | Engine coolant temp (THW) | temp_in | T8-C2-7 | Thermistor 1 | temp_in | corroborated | |
| OEM-E13-15 | VVT position sensor RH (VVR+) | trigger_in | T8-C2-2 | Wheel 1 | digital_in | corroborated | |
| OEM-E13-16 | VVT position sensor LH (VVL+) | trigger_in | T8-C2-29 | Cam 2 | trigger_in | corroborated | |
| OEM-E13-17 | ECU ground (E1) | ground | T8-C1-13 + T8-C1-14 | Power Ground 1 + Power Ground 2 | ground | corroborated | |
| OEM-E13-18 | Sensor ground (E2) | sensor_ground | T8-C2-21 + T8-C2-33 | Sensor Ground + Sensor Ground | sensor_ground | corroborated | |
| OEM-E13-19 | MAF ground (EVG) | sensor_ground | T8-C2-21 + T8-C2-33 | Sensor Ground + Sensor Ground | sensor_ground | corroborated | |
| OEM-E13-2 | +5V sensor reference (VC) | vref | T8-C2-24 | 5v Output | vref | corroborated | |
| OEM-E13-20 | Throttle position sensor 2 (VTA2) | analog_in | T8-C2-6 | Analogue 4 | analog_in | corroborated | |
| OEM-E13-21 | Accelerator pedal position 1 (VPA) | analog_in | T8-C2-5 | Analogue 3 | analog_in | corroborated | |
| OEM-E13-22 | Intake air temp (THA) | temp_in | T8-C2-25 | Thermistor 2 | temp_in | corroborated | |
| OEM-E13-23 | VVT position sensor RH (VVR−) | trigger_in | T8-C2-21 + T8-C2-33 | Sensor Ground + Sensor Ground | sensor_ground | corroborated | |
| OEM-E13-24 | VVT position sensor LH (VVL−) | trigger_in | T8-C2-21 + T8-C2-33 | Sensor Ground + Sensor Ground | sensor_ground | corroborated | |
| OEM-E13-3 | O2 sensor heater (bank unconfirmed) | low_side_out | T8-C3-23 | PWM 5 | low_side_out | corroborated | |
| OEM-E13-4 | O2 sensor heater (bank unconfirmed) | low_side_out | T8-C3-24 | PWM 6 | low_side_out | corroborated | |
| OEM-E13-5 | Injector 1 (cyl 1) | injector_out | T8-C1-9 | Injector 1 | injector_out | corroborated | |
| OEM-E13-6 | Injector 2 (cyl 2) | injector_out | T8-C1-17 | Injector 2 | injector_out | corroborated | |
| OEM-E13-8 | Throttle magnetic clutch − (CL−) | low_side_out | T8-C3-4 | PWM 9 | low_side_out | corroborated | |
| OEM-E13-9 | Accelerator pedal position 2 (VPA2) | analog_in | T8-C2-18 | Analogue 5 | analog_in | corroborated | |
| OEM-E14-1 | Injector 3 (cyl 3) | injector_out | T8-C1-34 | Injector 3 | injector_out | corroborated | |
| OEM-E14-10 | Camshaft position sensor (G2) | trigger_in | T8-C2-22 | Cam 1 | trigger_in | corroborated | |
| OEM-E14-11 | Ignition coil 1 (IGT1) | ignition_out | T8-C1-10 | Coil 1 | ignition_out | corroborated | |
| OEM-E14-12 | Ignition coil 2 (IGT2) | ignition_out | T8-C1-18 | Coil 2 | ignition_out | corroborated | |
| OEM-E14-13 | Ignition coil 3 (IGT3) | ignition_out | T8-C1-1 | Coil 3 | ignition_out | corroborated | |
| OEM-E14-14 | Ignition coil 4 (IGT4) | ignition_out | T8-C1-26 | Coil 4 | ignition_out | corroborated | |
| OEM-E14-15 | Ignition coil 5 (IGT5) | ignition_out | T8-C1-11 | Coil 5 | ignition_out | corroborated | |
| OEM-E14-16 | Ignition coil 6 (IGT6) | ignition_out | T8-C1-27 | Coil 6 | ignition_out | corroborated | |
| OEM-E14-17 | Knock sensor RH (KNKR) | knock_in | T8-C3-32 | Knock 2 | knock_in | corroborated | |
| OEM-E14-18 | Knock sensor LH (KNKL) | knock_in | T8-C3-31 | Knock 1 | knock_in | corroborated | |
| OEM-E14-19 | VVT oil-control valve LH (OCV−) | low_side_out | T8-C3-28 | PWM 10 | low_side_out | corroborated | |
| OEM-E14-2 | Injector 4 (cyl 4) | injector_out | T8-C1-25 | Injector 4 | injector_out | corroborated | |
| OEM-E14-20 | VVT oil-control valve LH (OCV+) | low_side_out | T8-C1-4 | PWM 2 | low_side_out | corroborated | |
| OEM-E14-21 | Power/injector ground (E01) | ground | T8-C1-13 + T8-C1-14 | Power Ground 1 + Power Ground 2 | ground | corroborated | |
| OEM-E14-22 | Crank position sensor (NE−) | trigger_in | T8-C2-21 + T8-C2-33 | Sensor Ground + Sensor Ground | sensor_ground | corroborated | |
| OEM-E14-23 | Crank position sensor (NE+) | trigger_in | T8-C2-12 | Crank | trigger_in | corroborated | |
| OEM-E14-25 | Ignition coil 7 (IGT7) | ignition_out | T8-C1-12 | Coil 7 | ignition_out | corroborated | |
| OEM-E14-26 | Ignition coil 8 (IGT8) | ignition_out | T8-C1-19 | Coil 8 | ignition_out | corroborated | |
| OEM-E14-27 | Ignition confirmation 1 (IGF1) | digital_in | T8-C2-4 | Digital 1 | digital_in | corroborated | |
| OEM-E14-28 | Ignition confirmation 2 (IGF2) | digital_in | T8-C2-8 | Digital 2 | digital_in | corroborated | |
| OEM-E14-29 | ACIS induction VSV | low_side_out | — | — | — | corroborated | |
| OEM-E14-3 | Injector 5 (cyl 5) | injector_out | T8-C1-16 | Injector 5 | injector_out | corroborated | |
| OEM-E14-4 | Injector 6 (cyl 6) | injector_out | T8-C1-15 | Injector 6 | injector_out | corroborated | |
| OEM-E14-5 | Injector 7 (cyl 7) | injector_out | T8-C1-24 | Injector 7 | injector_out | corroborated | |
| OEM-E14-6 | Injector 8 (cyl 8) | injector_out | T8-C1-23 | Injector 8 | injector_out | corroborated | |
| OEM-E14-7 | Throttle motor − (M−) | hbridge_out | T8-C1-7 | Motor 1 - | hbridge_out | corroborated | |
| OEM-E14-8 | Throttle motor + (M+) | hbridge_out | T8-C1-6 | Motor 1 + | hbridge_out | corroborated | |
| OEM-E15-1 | Battery constant (+12V) | power_in | T8-C3-26 | Permanent 12v | power_in | corroborated | |
| OEM-E15-10 | EFI main relay control (MREL) | low_side_out | T8-C1-3 | PWM 3 | low_side_out | corroborated | |
| OEM-E15-11 | OBD-II / DLC3 data (SIL) | serial | — | — | — | corroborated | |
| OEM-E15-16 | ECM power (EFI relay +B) | power_in | — | — | — | corroborated | |
| OEM-E15-5 | Fuel pump relay control (FC) | low_side_out | T8-C3-22 | PWM 4 | low_side_out | corroborated | |
| OEM-E15-6 | Check engine light (W) | low_side_out | — | — | — | corroborated | |
| OEM-E15-7 | ECM power feed (+BM) | power_in | — | — | — | corroborated | |
| OEM-E15-8 | ECM power (EFI relay +B1) | power_in | — | — | — | corroborated | |
| OEM-E15-9 | Ignition switch (+12V) | digital_in | T8-C1-31 | Ignition 12v In | power_in | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-E15-16 | SP-14V-1 | 0.85 | no route | ECM power (EFI relay +B) | — | |
| W2 | OEM-E15-7 | SP-14V-1 | 0.85 | no route | ECM power feed (+BM) | — | |
| W3 | OEM-E15-8 | SP-14V-1 | 0.85 | no route | ECM power (EFI relay +B1) | — | |
| W4 | OEM-E15-1 | T8-C3-26 | 0.85 | no route | Battery constant (+12V) | — | |
| W5 | NEW-BATT-1 | T8-C3-27 | 0.85 | no route | Permanent 12v | — | |
| W6 | OEM-E13-17 | SP-GND-1 | 0.85 | no route | ECU ground (E1) | — | |
| W7 | OEM-E14-21 | SP-GND-1 | 0.85 | no route | Power/injector ground (E01) | — | |
| W8 | SP-GND-1 | T8-C1-13 | 0.85 | no route | Power Ground 1 | — | |
| W9 | SP-GND-1 | T8-C1-14 | 0.85 | no route | Power Ground 2 | — | |
| W10 | OEM-E13-18 | SP-0V-1 | 0.5 | no route | Sensor ground (E2) | — | |
| W11 | OEM-E13-19 | SP-0V-1 | 0.5 | no route | MAF ground (EVG) | — | |
| W12 | SP-0V-1 | T8-C2-21 | 0.5 | no route | Sensor Ground | — | |
| W13 | SP-0V-1 | T8-C2-33 | 0.5 | no route | Sensor Ground | — | |
| W14 | OEM-E13-2 | T8-C2-24 | 0.5 | no route | +5V sensor reference (VC) | — | |
| W15 | OEM-E14-23 | T8-C2-12 | 0.5 | no route | Crank position sensor (NE+) | — | |
| W16 | OEM-E14-22 | SP-0V-1 | 0.5 | no route | Crank position sensor (NE−) | — | |
| W17 | OEM-E14-10 | T8-C2-22 | 0.5 | no route | Camshaft position sensor (G2) | — | |
| W18 | OEM-E13-16 | T8-C2-29 | 0.5 | no route | VVT position sensor LH (VVL+) | — | |
| W19 | OEM-E13-24 | SP-0V-1 | 0.5 | no route | VVT position sensor LH (VVL−) | — | |
| W20 | OEM-E13-15 | T8-C2-2 | 0.5 | no route | VVT position sensor RH (VVR+) | — | |
| W21 | OEM-E13-23 | SP-0V-1 | 0.5 | no route | VVT position sensor RH (VVR−) | — | |
| W22 | OEM-E14-18 | T8-C3-31 | 0.5 | no route | Knock sensor LH (KNKL) | — | |
| W23 | OEM-E14-17 | T8-C3-32 | 0.5 | no route | Knock sensor RH (KNKR) | — | |
| W24 | OEM-E14-11 | T8-C1-10 | 0.5 | no route | Ignition coil 1 (IGT1) | — | |
| W25 | OEM-E14-12 | T8-C1-18 | 0.5 | no route | Ignition coil 2 (IGT2) | — | |
| W26 | OEM-E14-13 | T8-C1-1 | 0.5 | no route | Ignition coil 3 (IGT3) | — | |
| W27 | OEM-E14-14 | T8-C1-26 | 0.5 | no route | Ignition coil 4 (IGT4) | — | |
| W28 | OEM-E14-15 | T8-C1-11 | 0.5 | no route | Ignition coil 5 (IGT5) | — | |
| W29 | OEM-E14-16 | T8-C1-27 | 0.5 | no route | Ignition coil 6 (IGT6) | — | |
| W30 | OEM-E14-25 | T8-C1-12 | 0.5 | no route | Ignition coil 7 (IGT7) | — | |
| W31 | OEM-E14-26 | T8-C1-19 | 0.5 | no route | Ignition coil 8 (IGT8) | — | |
| W32 | OEM-E13-5 | T8-C1-9 | 0.5 | no route | Injector 1 (cyl 1) | — | |
| W33 | OEM-E13-6 | T8-C1-17 | 0.5 | no route | Injector 2 (cyl 2) | — | |
| W34 | OEM-E14-1 | T8-C1-34 | 0.5 | no route | Injector 3 (cyl 3) | — | |
| W35 | OEM-E14-2 | T8-C1-25 | 0.5 | no route | Injector 4 (cyl 4) | — | |
| W36 | OEM-E14-3 | T8-C1-16 | 0.5 | no route | Injector 5 (cyl 5) | — | |
| W37 | OEM-E14-4 | T8-C1-15 | 0.5 | no route | Injector 6 (cyl 6) | — | |
| W38 | OEM-E14-5 | T8-C1-24 | 0.5 | no route | Injector 7 (cyl 7) | — | |
| W39 | OEM-E14-6 | T8-C1-23 | 0.5 | no route | Injector 8 (cyl 8) | — | |
| W40 | OEM-E14-7 | T8-C1-7 | 0.5 | no route | Throttle motor − (M−) | — | |
| W41 | OEM-E14-8 | T8-C1-6 | 0.5 | no route | Throttle motor + (M+) | — | |
| W42 | OEM-E15-9 | T8-C1-31 | 0.5 | no route | Ignition switch (+12V) | — | |
| W43 | OEM-E11-19 | T8-C1-5 | 0.5 | no route | VVT oil-control valve RH (OCR+) | — | |
| W44 | OEM-E14-20 | T8-C1-4 | 0.5 | no route | VVT oil-control valve LH (OCV+) | — | |
| W45 | OEM-E13-10 | T8-C2-10 | 0.5 | no route | MAF signal (VG) | — | |
| W46 | OEM-E13-13 | T8-C2-1 | 0.5 | no route | Throttle position sensor 1 (VTA) | — | |
| W47 | OEM-E13-21 | T8-C2-5 | 0.5 | no route | Accelerator pedal position 1 (VPA) | — | |
| W48 | OEM-E13-20 | T8-C2-6 | 0.5 | no route | Throttle position sensor 2 (VTA2) | — | |
| W49 | OEM-E13-9 | T8-C2-18 | 0.5 | no route | Accelerator pedal position 2 (VPA2) | — | |
| W50 | OEM-E13-14 | T8-C2-7 | 0.5 | no route | Engine coolant temp (THW) | — | |
| W51 | OEM-E15-10 | T8-C1-3 | 0.5 | no route | EFI main relay control (MREL) | — | |
| W52 | OEM-E15-5 | T8-C3-22 | 0.5 | no route | Fuel pump relay control (FC) | — | |
| W53 | OEM-E11-7 | T8-C3-9 | 0.5 | no route | O2 sensor heater (bank unconfirmed) | — | |
| W54 | OEM-E11-8 | T8-C3-3 | 0.5 | no route | O2 sensor heater (bank unconfirmed) | — | |
| W55 | OEM-E13-3 | T8-C3-23 | 0.5 | no route | O2 sensor heater (bank unconfirmed) | — | |
| W56 | OEM-E13-4 | T8-C3-24 | 0.5 | no route | O2 sensor heater (bank unconfirmed) | — | |
| W57 | OEM-E11-28 | T8-C3-25 | 0.5 | no route | VVT oil-control valve RH (OCR−) | — | |
| W58 | OEM-E12-12 | T8-C3-10 | 0.5 | no route | Throttle magnetic clutch + (CL+) | — | |
| W59 | OEM-E13-8 | T8-C3-4 | 0.5 | no route | Throttle magnetic clutch − (CL−) | — | |
| W60 | OEM-E14-19 | T8-C3-28 | 0.5 | no route | VVT oil-control valve LH (OCV−) | — | |
| W61 | OEM-E11-18 | T8-C2-19 | 0.5 | no route | O2 sensor signal (bank unconfirmed) | — | |
| W62 | OEM-E11-27 | T8-C3-17 | 0.5 | no route | O2 sensor signal (bank unconfirmed) | — | |
| W63 | OEM-E13-11 | T8-C3-18 | 0.5 | no route | O2 sensor signal (bank unconfirmed) | — | |
| W64 | OEM-E13-12 | T8-C2-34 | 0.5 | no route | O2 sensor signal (bank unconfirmed) | — | |
| W65 | OEM-E13-22 | T8-C2-25 | 0.5 | no route | Intake air temp (THA) | — | |
| W66 | OEM-E14-27 | T8-C2-4 | 0.5 | no route | Ignition confirmation 1 (IGF1) | — | |
| W67 | OEM-E14-28 | T8-C2-8 | 0.5 | no route | Ignition confirmation 2 (IGF2) | — | |
| W68 | OEM-E11-17 | T8-C2-11 | 0.5 | no route | Starter signal (STA) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 4-1437290-0 | TE | Superseal 1.0 34-way plug, Key 1 | 3.000 | ea |
| terminal | 3-1447221-4 | TE | Superseal 1.0 socket terminal, 20 AWG (0.5 sq mm) | 58.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (9)
| Severity | Code | Subject | Message |
|---|---|---|---|
| warn | DATASET_GAP | T8+ C1 | 10 of 34 cavities on T8+ C1 have no pin data (2,8,20,21,22,28,29,30,32,33). Anything there is invisible to these checks. |
| warn | DATASET_GAP | T8+ C2 | 2 of 34 cavities on T8+ C2 have no pin data (23,30). Anything there is invisible to these checks. |
| warn | DATASET_GAP | T8+ C3 | 9 of 34 cavities on T8+ C3 have no pin data (13,14,15,16,19,20,21,29,30). Anything there is invisible to these checks. |
| warn | DBW_MOTOR_CURRENT | T8-C1-6 | Cannot confirm T8+ can drive the throttle motor: neither the motor stall current (OEM-E14-8) nor the peak rating of T8-C1-6 "Motor 1 +" is known. |
| warn | DBW_MOTOR_CURRENT | T8-C1-7 | Cannot confirm T8+ can drive the throttle motor: neither the motor stall current (OEM-E14-7) nor the peak rating of T8-C1-7 "Motor 1 -" is known. |
| warn | NET_FAMILY | OEM-E13-15 ↔ T8-C2-2 | OEM-E13-15 "VVT position sensor RH (VVR+)" [trigger_in] is wired to T8-C2-2 "Wheel 1" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| info | NET_FAMILY | OEM-E13-23 ↔ T8-C2-33 | OEM-E13-23 "VVT position sensor RH (VVR−)" [trigger_in] is wired to T8-C2-33 "Sensor Ground" [sensor_ground]. Trigger return tied to sensor/trigger ground: correct for single-ended trigger inputs. |
| info | NET_FAMILY | OEM-E15-9 ↔ T8-C1-31 | OEM-E15-9 "Ignition switch (+12V)" [digital_in] is wired to T8-C1-31 "Ignition 12v In" [power_in]. Switched supply used as the ignition-on sense. |
| info | UNMAPPED | OEM | 4 optional OEM pins are not mapped: OEM-E11-5 Diagnostic test (TC); OEM-E14-29 ACIS induction VSV; OEM-E15-11 OBD-II / DLC3 data (SIL); OEM-E15-6 Check engine light (W) |
Accepted (0)
| Code | Subject | Reason | By |
|---|
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-18. Review every wire against both manuals before building. Not wired: - OEM-E14 29: ACIS induction VSV: no free low_side/relay_control/heater_low_side/ls_hs/injector on DTAFast T8+ - OEM-E15 6: Check engine light (W): no free low_side/relay_control/heater_low_side/ls_hs/injector on DTAFast T8+ - OEM-E15 11: OBD-II / DLC3 data (SIL): no free k_line on DTAFast T8+ - OEM-E11 5: Diagnostic test (TC): no free k_line on DTAFast T8+
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | DTAFast T8+ ECU wiring diagram | https://cdn.shopify.com/s/files/1/0848/7508/4108/files/T8PLUS_Wiring-Diagram.pdf?v=1728572013 | — | — | — |
| 4 | vendor_doc | Toyota 1UZ-FE (VVT-i) engine manual M1UZ | http://www.epicmarine.com/docs/M1UZrm.pdf | — | — | — |
| 3 | community_copy | 1998 Lexus LS400 ECM terminal voltage chart (RM717U translation) | https://www.renrendoc.com/p-59096353.html | — | — | — |