BMW 3 Series E46 1998–2006 (M54) → Link G4X AtomX 111-4000 (auto)
BMW 3 Series E46 1998–2006 (M54) — Link — G4X AtomX
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-23
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 4: read the Findings page before cutting any wire |
| Size of the job | 60 wires · 13 connectors · 1 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-X60001-8 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-X60001-9 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | OEM-X60004-26 | MAIN-R-COIL+ | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | NEW-BATT-1 | MAIN-R-IN | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | MAIN-R-COIL- | SP-GND-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | MAIN-R-OUT | G4XATOMX-A-A5 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-X60001-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-X60001-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | OEM-X60001-6 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-X60005-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | SP-GND-1 | G4XATOMX-A-A25 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | SP-GND-1 | G4XATOMX-A-A34 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-X60002-20 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-X60002-21 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-X60002-22 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-X60002-24 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-X60003-15 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-X60003-17 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-X60003-18 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-X60003-20 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-X60003-21 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-X60003-23 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-X60003-25 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-X60003-28 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-X60004-12 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-X60004-39 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-X60004-7 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | SP-0V-1 | G4XATOMX-A-A24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-X60003-7 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-X60004-14 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-X60004-9 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | SP-5V1-1 | G4XATOMX-A-A32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-X60003-8 | G4XATOMX-A-A8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-X60003-2 | G4XATOMX-A-A9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-X60003-5 | G4XATOMX-A-A30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-X60003-29 | G4XATOMX-A-A6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-X60005-3 | G4XATOMX-A-A13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-X60005-2 | G4XATOMX-A-A12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-X60005-1 | G4XATOMX-A-A11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-X60005-9 | G4XATOMX-A-A10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-X60003-33 | G4XATOMX-A-A4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-X60003-34 | G4XATOMX-A-A3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-X60003-35 | G4XATOMX-A-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-X60003-36 | G4XATOMX-A-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-X60003-37 | G4XATOMX-A-A4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-X60003-38 | G4XATOMX-A-A3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | OEM-X60003-48 | SP-SHD-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | SP-SHD-1 | G4XATOMX-A-A7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W49 | OEM-X60003-1 | G4XATOMX-A-A17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W50 | OEM-X60003-19 | G4XATOMX-A-A22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W51 | OEM-X60004-8 | G4XATOMX-A-A33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W52 | OEM-X60003-24 | G4XATOMX-A-A15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W53 | OEM-X60001-1 | G4XATOMX-A-A21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W54 | OEM-X60002-23 | G4XATOMX-A-A20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W55 | OEM-X60004-10 | G4XATOMX-A-A19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W56 | OEM-X60004-29 | G4XATOMX-A-A18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W57 | OEM-X60003-22 | G4XATOMX-A-A16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W58 | OEM-X60004-22 | G4XATOMX-A-A31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W59 | OEM-X60004-36 | G4XATOMX-A-A28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W60 | OEM-X60004-37 | G4XATOMX-A-A29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | OEM-X60001-8 | G4XATOMX-A-A24 | open (OL) | +12 V supply must not touch sensor ground | |
| 2 | G4XATOMX-A-A24 | G4XATOMX-A-A32 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 3 | G4XATOMX-A-A24 | G4XATOMX-A-A5 | open (OL) | sensor ground must not touch +12 V supply | |
| 4 | G4XATOMX-A-A24 | MAIN-R-COIL+ | open (OL) | sensor ground must not touch +12 V supply | |
| 5 | G4XATOMX-A-A24 | NEW-BATT-1 | open (OL) | sensor ground must not touch +12 V supply | |
| 6 | G4XATOMX-A-A25 | G4XATOMX-A-A32 | open (OL) | power ground must not touch 5 V sensor reference | |
| 7 | G4XATOMX-A-A25 | G4XATOMX-A-A5 | open (OL) | power ground must not touch +12 V supply | |
| 8 | G4XATOMX-A-A25 | MAIN-R-COIL+ | open (OL) | power ground must not touch +12 V supply | |
| 9 | G4XATOMX-A-A25 | NEW-BATT-1 | open (OL) | power ground must not touch +12 V supply | |
| 10 | G4XATOMX-A-A25 | OEM-X60001-8 | open (OL) | power ground must not touch +12 V supply | |
| 11 | G4XATOMX-A-A32 | G4XATOMX-A-A5 | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 12 | G4XATOMX-A-A32 | MAIN-R-COIL+ | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 13 | G4XATOMX-A-A32 | NEW-BATT-1 | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 14 | OEM-X60001-8 | G4XATOMX-A-A32 | open (OL) | +12 V supply must not touch 5 V sensor reference |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
G4XATOMX-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A1 | Injector 4 | — | W44 | — | 0.5 | OEM-X60003-36 | — | — | — |
| A10 | Ignition 4 | — | W40 | — | 0.5 | OEM-X60005-9 | — | — | — |
| A11 | Ignition 3 | — | W39 | — | 0.5 | OEM-X60005-1 | — | — | — |
| A12 | Ignition 2 | — | W38 | — | 0.5 | OEM-X60005-2 | — | — | — |
| A13 | Ignition 1 | — | W37 | — | 0.5 | OEM-X60005-3 | — | — | — |
| A15 | Analog Temp 1 | — | W52 | — | 0.5 | OEM-X60003-24 | — | — | — |
| A16 | Analog Temp 2 | — | W57 | — | 0.5 | OEM-X60003-22 | — | — | — |
| A17 | Analog Volt 1 | — | W49 | — | 0.5 | OEM-X60003-1 | — | — | — |
| A18 | Aux 4 | — | W56 | — | 0.5 | OEM-X60004-29 | — | — | — |
| A19 | Aux 3 | — | W55 | — | 0.5 | OEM-X60004-10 | — | — | — |
| A2 | Injector 3 | — | W43 | — | 0.5 | OEM-X60003-35 | — | — | — |
| A20 | Aux 2 | — | W54 | — | 0.5 | OEM-X60002-23 | — | — | — |
| A21 | Aux 1 | — | W53 | — | 0.5 | OEM-X60001-1 | — | — | — |
| A22 | Analog Volt 2 | — | W50 | — | 0.5 | OEM-X60003-19 | — | — | — |
| A24 | Sensor Ground | — | W28 | — | 0.5 | SP-0V-1 | — | — | — |
| A25 | System Ground | — | W11 | — | 0.85 | SP-GND-1 | — | — | — |
| A28 | CAN H | — | W59 | — | 0.5 | OEM-X60004-36 | — | — | — |
| A29 | CAN L | — | W60 | — | 0.5 | OEM-X60004-37 | — | — | — |
| A3 | Injector 2 | — | W42 | — | 0.5 | OEM-X60003-34 | — | — | — |
| A3 | Injector 2 | — | W46 | — | 0.5 | OEM-X60003-38 | — | — | — |
| A30 | Digital Input 1 | — | W35 | — | 0.5 | OEM-X60003-5 | — | — | — |
| A31 | Digital Input 2 | — | W58 | — | 0.5 | OEM-X60004-22 | — | — | — |
| A32 | +5V Out | — | W32 | — | 0.5 | SP-5V1-1 | — | — | — |
| A33 | Analog Volt 3 | — | W51 | — | 0.5 | OEM-X60004-8 | — | — | — |
| A34 | System Ground | — | W12 | — | 0.85 | SP-GND-1 | — | — | — |
| A4 | Injector 1 | — | W41 | — | 0.5 | OEM-X60003-33 | — | — | — |
| A4 | Injector 1 | — | W45 | — | 0.5 | OEM-X60003-37 | — | — | — |
| A5 | +14V ECU Power | — | W6 | — | 0.85 | MAIN-R-OUT | — | — | — |
| A6 | Knock 1 | — | W36 | — | 0.5 | OEM-X60003-29 | — | — | — |
| A7 | Shield Ground | — | W48 | — | 0.5 | SP-SHD-1 | — | — | — |
| A8 | Trigger 1 | — | W33 | — | 0.5 | OEM-X60003-8 | — | — | — |
| A9 | Trigger 2 | — | W34 | — | 0.5 | OEM-X60003-2 | — | — | — |
MAIN-R
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| COIL+ | Relay coil positive (ignition-switched +12V) | — | W3 | — | 0.5 | OEM-X60004-26 | — | — | — |
| COIL- | Relay coil negative (ECU low-side driver) | — | W5 | — | 0.5 | SP-GND-1 | — | — | — |
| IN | Relay contact input (battery + via main fuse) | — | W4 | — | 0.85 | NEW-BATT-1 | — | — | — |
| OUT | Relay contact output (switched +12V bus) | — | W6 | — | 0.85 | G4XATOMX-A-A5 | — | — | — |
NEW-BATT
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W4 | — | 0.85 | MAIN-R-IN | — | — | — |
OEM-X60001
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector/unloader relay control (terminal 15) | — | W53 | — | 0.5 | G4XATOMX-A-A21 | — | — | — |
| 4 | Power ground | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | Power ground | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Power ground | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 7 | Battery constant (terminal 30) | — | — | — | — | — | — | — | — |
| 8 | ECU main power (terminal 87 via main relay) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 9 | Voltage supply (injector / fuse carrier) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
OEM-X60002
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | O2 sensor heater, bank 1 pre-cat | — | — | — | — | — | — | — | — |
| 13 | O2 sensor heater, bank 2 pre-cat | — | — | — | — | — | — | — | — |
| 14 | O2 sensor signal, bank 1 pre-cat | — | — | — | — | — | — | — | — |
| 15 | O2 sensor signal, bank 2 pre-cat | — | — | — | — | — | — | — | — |
| 16 | O2 sensor signal, bank 1 post-cat | — | — | — | — | — | — | — | — |
| 18 | O2 sensor signal, bank 2 post-cat | — | — | — | — | — | — | — | — |
| 19 | O2 sensor heater, bank 2 post-cat | — | — | — | — | — | — | — | — |
| 20 | O2 sensor ground, bank 1 pre-cat | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 21 | O2 sensor ground, bank 2 pre-cat | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | O2 sensor ground, bank 1 post-cat | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 23 | Main relay control | — | W54 | — | 0.5 | G4XATOMX-A-A20 | — | — | — |
| 24 | O2 sensor ground, bank 2 post-cat | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 7 | O2 sensor heater, bank 1 post-cat | — | — | — | — | — | — | — | — |
OEM-X60003
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Mass air flow (MAF) signal | — | W49 | — | 0.5 | G4XATOMX-A-A17 | — | — | — |
| 10 | Throttle position sensor 2 | — | — | — | — | — | — | — | — |
| 15 | Exhaust camshaft ground | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 17 | MAF ground | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 18 | Intake camshaft ground | — | W19 | — | 0.5 | SP-0V-1 | — | — | — |
| 19 | Throttle position sensor 1 | — | W50 | — | 0.5 | G4XATOMX-A-A22 | — | — | — |
| 2 | Exhaust camshaft position | — | W34 | — | 0.5 | G4XATOMX-A-A9 | — | — | — |
| 20 | Throttle ground | — | W20 | — | 0.5 | SP-0V-1 | — | — | — |
| 21 | Crankshaft ground | — | W21 | — | 0.5 | SP-0V-1 | — | — | — |
| 22 | Intake air temperature (IAT) | — | W57 | — | 0.5 | G4XATOMX-A-A16 | — | — | — |
| 23 | IAT ground | — | W22 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | Engine coolant temperature (ECT) | — | W52 | — | 0.5 | G4XATOMX-A-A15 | — | — | — |
| 25 | ECT ground | — | W23 | — | 0.5 | SP-0V-1 | — | — | — |
| 27 | Engine oil temperature | — | — | — | — | — | — | — | — |
| 28 | Oil temperature ground | — | W24 | — | 0.5 | SP-0V-1 | — | — | — |
| 29 | Knock sensor, cylinders 1-3 (A) | — | W36 | — | 0.5 | G4XATOMX-A-A6 | — | — | — |
| 30 | Knock sensor, cylinders 1-3 (B) | — | — | — | — | — | — | — | — |
| 31 | Knock sensor, cylinders 4-6 (A) | — | — | — | — | — | — | — | — |
| 32 | Knock sensor, cylinders 4-6 (B) | — | — | — | — | — | — | — | — |
| 33 | Injector cylinder 1 | — | W41 | — | 0.5 | G4XATOMX-A-A4 | — | — | — |
| 34 | Injector cylinder 2 | — | W42 | — | 0.5 | G4XATOMX-A-A3 | — | — | — |
| 35 | Injector cylinder 3 | — | W43 | — | 0.5 | G4XATOMX-A-A2 | — | — | — |
| 36 | Injector cylinder 4 | — | W44 | — | 0.5 | G4XATOMX-A-A1 | — | — | — |
| 37 | Injector cylinder 5 | — | W45 | — | 0.5 | G4XATOMX-A-A4 | — | — | — |
| 38 | Injector cylinder 6 | — | W46 | — | 0.5 | G4XATOMX-A-A3 | — | — | — |
| 40 | VANOS intake solenoid | — | — | — | — | — | — | — | — |
| 41 | VANOS exhaust solenoid | — | — | — | — | — | — | — | — |
| 42 | Evap purge valve | — | — | — | — | — | — | — | — |
| 43 | Throttle motor − (M−) | — | — | — | — | — | — | — | — |
| 44 | Throttle motor + (M+) | — | — | — | — | — | — | — | — |
| 45 | Map-controlled thermostat | — | — | — | — | — | — | — | — |
| 46 | Idle speed control, close | — | — | — | — | — | — | — | — |
| 47 | Idle speed control, open | — | — | — | — | — | — | — | — |
| 48 | Knock sensor shield | — | W47 | — | 0.5 | SP-SHD-1 | — | — | — |
| 49 | DISA intake flap | — | — | — | — | — | — | — | — |
| 5 | Intake camshaft position | — | W35 | — | 0.5 | G4XATOMX-A-A30 | — | — | — |
| 51 | Fuel tank leakage diagnostic heater | — | — | — | — | — | — | — | — |
| 52 | Secondary air pump valve | — | — | — | — | — | — | — | — |
| 7 | Throttle body +5V supply | — | W29 | — | 0.5 | SP-5V1-1 | — | — | — |
| 8 | Crankshaft position | — | W33 | — | 0.5 | G4XATOMX-A-A8 | — | — | — |
OEM-X60004
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | Fuel pump relay control | — | W55 | — | 0.5 | G4XATOMX-A-A19 | — | — | — |
| 12 | Pedal ground 2 | — | W25 | — | 0.5 | SP-0V-1 | — | — | — |
| 13 | Pedal position signal 2 | — | — | — | — | — | — | — | — |
| 14 | Pedal +5V supply 2 | — | W30 | — | 0.5 | SP-5V1-1 | — | — | — |
| 17 | Engine speed (RPM) output | — | — | — | — | — | — | — | — |
| 18 | Exhaust flap valve control | — | — | — | — | — | — | — | — |
| 20 | Fuel tank leakage diagnostic pump | — | — | — | — | — | — | — | — |
| 22 | Rear wheel speed input | — | W58 | — | 0.5 | G4XATOMX-A-A31 | — | — | — |
| 23 | Clutch switch input | — | — | — | — | — | — | — | — |
| 24 | Brake light switch input (pin 4) | — | — | — | — | — | — | — | — |
| 26 | Ignition switch (terminal 15) | — | W3 | — | 0.5 | MAIN-R-COIL+ | — | — | — |
| 28 | Brake light switch input (pin 3) | — | — | — | — | — | — | — | — |
| 29 | A/C relay control | — | W56 | — | 0.5 | G4XATOMX-A-A18 | — | — | — |
| 3 | Secondary air pump relay control | — | — | — | — | — | — | — | — |
| 30 | Fuel tank leakage diagnostic valve | — | — | — | — | — | — | — | — |
| 32 | Diagnostic TX (K-line) | — | — | — | — | — | — | — | — |
| 33 | Drive-away protection (anti-theft) | — | — | — | — | — | — | — | — |
| 36 | CAN bus high | — | W59 | — | 0.5 | G4XATOMX-A-A28 | — | — | — |
| 37 | CAN bus low | — | W60 | — | 0.5 | G4XATOMX-A-A29 | — | — | — |
| 38 | Coolant outlet temperature sensor | — | — | — | — | — | — | — | — |
| 39 | Coolant outlet temperature sensor ground | — | W26 | — | 0.5 | SP-0V-1 | — | — | — |
| 4 | Cooling fan control | — | — | — | — | — | — | — | — |
| 7 | Pedal ground 1 | — | W27 | — | 0.5 | SP-0V-1 | — | — | — |
| 8 | Pedal position signal 1 | — | W51 | — | 0.5 | G4XATOMX-A-A33 | — | — | — |
| 9 | Pedal +5V supply 1 | — | W31 | — | 0.5 | SP-5V1-1 | — | — | — |
OEM-X60005
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Ignition coil 3 | — | W39 | — | 0.5 | G4XATOMX-A-A11 | — | — | — |
| 2 | Ignition coil 2 | — | W38 | — | 0.5 | G4XATOMX-A-A12 | — | — | — |
| 3 | Ignition coil 1 | — | W37 | — | 0.5 | G4XATOMX-A-A13 | — | — | — |
| 5 | Ignition ground | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 7 | Ignition coil 6 | — | — | — | — | — | — | — | — |
| 8 | Ignition coil 5 | — | — | — | — | — | — | — | — |
| 9 | Ignition coil 4 | — | W40 | — | 0.5 | G4XATOMX-A-A10 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W13 | — | 0.5 | OEM-X60002-20 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | OEM-X60002-21 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | OEM-X60002-22 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-X60002-24 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | OEM-X60003-15 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | OEM-X60003-17 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | OEM-X60003-18 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | OEM-X60003-20 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | OEM-X60003-21 | — | — | — |
| 1 | — | — | W22 | — | 0.5 | OEM-X60003-23 | — | — | — |
| 1 | — | — | W23 | — | 0.5 | OEM-X60003-25 | — | — | — |
| 1 | — | — | W24 | — | 0.5 | OEM-X60003-28 | — | — | — |
| 1 | — | — | W25 | — | 0.5 | OEM-X60004-12 | — | — | — |
| 1 | — | — | W26 | — | 0.5 | OEM-X60004-39 | — | — | — |
| 1 | — | — | W27 | — | 0.5 | OEM-X60004-7 | — | — | — |
| 1 | — | — | W28 | — | 0.5 | G4XATOMX-A-A24 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-X60001-8 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-X60001-9 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W29 | — | 0.5 | OEM-X60003-7 | — | — | — |
| 1 | — | — | W30 | — | 0.5 | OEM-X60004-14 | — | — | — |
| 1 | — | — | W31 | — | 0.5 | OEM-X60004-9 | — | — | — |
| 1 | — | — | W32 | — | 0.5 | G4XATOMX-A-A32 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W5 | — | 0.5 | MAIN-R-COIL- | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-X60001-4 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | OEM-X60001-5 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | OEM-X60001-6 | — | — | — |
| 1 | — | — | W10 | — | 0.85 | OEM-X60005-5 | — | — | — |
| 1 | — | — | W11 | — | 0.85 | G4XATOMX-A-A25 | — | — | — |
| 1 | — | — | W12 | — | 0.85 | G4XATOMX-A-A34 | — | — | — |
SP-SHD
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W47 | — | 0.5 | OEM-X60003-48 | — | — | — |
| 1 | — | — | W48 | — | 0.5 | G4XATOMX-A-A7 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-X60001-1 | Injector/unloader relay control (terminal 15) | low_side_out | G4XATOMX-A-A21 | Aux 1 | low_side_out | corroborated | |
| OEM-X60001-4 | Power ground | ground | G4XATOMX-A-A25 + G4XATOMX-A-A34 + MAIN-R-COIL- | System Ground + System Ground + Relay coil negative (ECU low-side driver) | ground + load | corroborated | |
| OEM-X60001-5 | Power ground | ground | G4XATOMX-A-A25 + G4XATOMX-A-A34 + MAIN-R-COIL- | System Ground + System Ground + Relay coil negative (ECU low-side driver) | ground + load | corroborated | |
| OEM-X60001-6 | Power ground | ground | G4XATOMX-A-A25 + G4XATOMX-A-A34 + MAIN-R-COIL- | System Ground + System Ground + Relay coil negative (ECU low-side driver) | ground + load | corroborated | |
| OEM-X60001-7 | Battery constant (terminal 30) | power_in | — | — | — | corroborated | |
| OEM-X60001-8 | ECU main power (terminal 87 via main relay) | power_in | — | — | — | corroborated | |
| OEM-X60001-9 | Voltage supply (injector / fuse carrier) | power_in | — | — | — | corroborated | |
| OEM-X60002-1 | O2 sensor heater, bank 1 pre-cat | low_side_out | — | — | — | corroborated | |
| OEM-X60002-13 | O2 sensor heater, bank 2 pre-cat | low_side_out | — | — | — | corroborated | |
| OEM-X60002-14 | O2 sensor signal, bank 1 pre-cat | lambda_nb_in | — | — | — | corroborated | |
| OEM-X60002-15 | O2 sensor signal, bank 2 pre-cat | lambda_nb_in | — | — | — | corroborated | |
| OEM-X60002-16 | O2 sensor signal, bank 1 post-cat | lambda_nb_in | — | — | — | corroborated | |
| OEM-X60002-18 | O2 sensor signal, bank 2 post-cat | lambda_nb_in | — | — | — | corroborated | |
| OEM-X60002-19 | O2 sensor heater, bank 2 post-cat | low_side_out | — | — | — | corroborated | |
| OEM-X60002-20 | O2 sensor ground, bank 1 pre-cat | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60002-21 | O2 sensor ground, bank 2 pre-cat | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60002-22 | O2 sensor ground, bank 1 post-cat | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60002-23 | Main relay control | low_side_out | G4XATOMX-A-A20 | Aux 2 | low_side_out | corroborated | |
| OEM-X60002-24 | O2 sensor ground, bank 2 post-cat | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60002-7 | O2 sensor heater, bank 1 post-cat | low_side_out | — | — | — | corroborated | |
| OEM-X60003-1 | Mass air flow (MAF) signal | analog_in | G4XATOMX-A-A17 | Analog Volt 1 | analog_in | corroborated | |
| OEM-X60003-10 | Throttle position sensor 2 | analog_in | — | — | — | corroborated | |
| OEM-X60003-15 | Exhaust camshaft ground | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60003-17 | MAF ground | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60003-18 | Intake camshaft ground | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60003-19 | Throttle position sensor 1 | analog_in | G4XATOMX-A-A22 | Analog Volt 2 | analog_in | corroborated | |
| OEM-X60003-2 | Exhaust camshaft position | trigger_in | G4XATOMX-A-A9 | Trigger 2 | trigger_in | corroborated | |
| OEM-X60003-20 | Throttle ground | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60003-21 | Crankshaft ground | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60003-22 | Intake air temperature (IAT) | temp_in | G4XATOMX-A-A16 | Analog Temp 2 | temp_in | corroborated | |
| OEM-X60003-23 | IAT ground | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60003-24 | Engine coolant temperature (ECT) | temp_in | G4XATOMX-A-A15 | Analog Temp 1 | temp_in | corroborated | |
| OEM-X60003-25 | ECT ground | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60003-27 | Engine oil temperature | temp_in | — | — | — | corroborated | |
| OEM-X60003-28 | Oil temperature ground | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60003-29 | Knock sensor, cylinders 1-3 (A) | knock_in | G4XATOMX-A-A6 | Knock 1 | knock_in | corroborated | |
| OEM-X60003-30 | Knock sensor, cylinders 1-3 (B) | knock_in | — | — | — | corroborated | |
| OEM-X60003-31 | Knock sensor, cylinders 4-6 (A) | knock_in | — | — | — | corroborated | |
| OEM-X60003-32 | Knock sensor, cylinders 4-6 (B) | knock_in | — | — | — | corroborated | |
| OEM-X60003-33 | Injector cylinder 1 | injector_out | G4XATOMX-A-A4 | Injector 1 | injector_out | corroborated | |
| OEM-X60003-34 | Injector cylinder 2 | injector_out | G4XATOMX-A-A3 | Injector 2 | injector_out | corroborated | |
| OEM-X60003-35 | Injector cylinder 3 | injector_out | G4XATOMX-A-A2 | Injector 3 | injector_out | corroborated | |
| OEM-X60003-36 | Injector cylinder 4 | injector_out | G4XATOMX-A-A1 | Injector 4 | injector_out | corroborated | |
| OEM-X60003-37 | Injector cylinder 5 | injector_out | G4XATOMX-A-A4 | Injector 1 | injector_out | corroborated | |
| OEM-X60003-38 | Injector cylinder 6 | injector_out | G4XATOMX-A-A3 | Injector 2 | injector_out | corroborated | |
| OEM-X60003-40 | VANOS intake solenoid | low_side_out | — | — | — | corroborated | |
| OEM-X60003-41 | VANOS exhaust solenoid | low_side_out | — | — | — | corroborated | |
| OEM-X60003-42 | Evap purge valve | low_side_out | — | — | — | corroborated | |
| OEM-X60003-43 | Throttle motor − (M−) | hbridge_out | — | — | — | corroborated | |
| OEM-X60003-44 | Throttle motor + (M+) | hbridge_out | — | — | — | corroborated | |
| OEM-X60003-45 | Map-controlled thermostat | low_side_out | — | — | — | corroborated | |
| OEM-X60003-46 | Idle speed control, close | hbridge_out | — | — | — | corroborated | |
| OEM-X60003-47 | Idle speed control, open | hbridge_out | — | — | — | corroborated | |
| OEM-X60003-48 | Knock sensor shield | shield | G4XATOMX-A-A7 | Shield Ground | shield | corroborated | |
| OEM-X60003-49 | DISA intake flap | low_side_out | — | — | — | corroborated | |
| OEM-X60003-5 | Intake camshaft position | trigger_in | G4XATOMX-A-A30 | Digital Input 1 | digital_in | corroborated | |
| OEM-X60003-51 | Fuel tank leakage diagnostic heater | low_side_out | — | — | — | single_source | |
| OEM-X60003-52 | Secondary air pump valve | low_side_out | — | — | — | single_source | |
| OEM-X60003-7 | Throttle body +5V supply | vref | G4XATOMX-A-A32 | +5V Out | vref | corroborated | |
| OEM-X60003-8 | Crankshaft position | trigger_in | G4XATOMX-A-A8 | Trigger 1 | trigger_in | corroborated | |
| OEM-X60004-10 | Fuel pump relay control | low_side_out | G4XATOMX-A-A19 | Aux 3 | low_side_out | corroborated | |
| OEM-X60004-12 | Pedal ground 2 | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60004-13 | Pedal position signal 2 | analog_in | — | — | — | corroborated | |
| OEM-X60004-14 | Pedal +5V supply 2 | vref | G4XATOMX-A-A32 | +5V Out | vref | corroborated | |
| OEM-X60004-17 | Engine speed (RPM) output | tacho_out | — | — | — | single_source | |
| OEM-X60004-18 | Exhaust flap valve control | low_side_out | — | — | — | single_source | |
| OEM-X60004-20 | Fuel tank leakage diagnostic pump | low_side_out | — | — | — | single_source | |
| OEM-X60004-22 | Rear wheel speed input | digital_in | G4XATOMX-A-A31 | Digital Input 2 | digital_in | single_source | |
| OEM-X60004-23 | Clutch switch input | digital_in | — | — | — | single_source | |
| OEM-X60004-24 | Brake light switch input (pin 4) | digital_in | — | — | — | single_source | |
| OEM-X60004-26 | Ignition switch (terminal 15) | digital_in | MAIN-R-COIL+ | Relay coil positive (ignition-switched +12V) | power_in | single_source | |
| OEM-X60004-28 | Brake light switch input (pin 3) | digital_in | — | — | — | single_source | |
| OEM-X60004-29 | A/C relay control | low_side_out | G4XATOMX-A-A18 | Aux 4 | low_side_out | single_source | |
| OEM-X60004-3 | Secondary air pump relay control | low_side_out | — | — | — | single_source | |
| OEM-X60004-30 | Fuel tank leakage diagnostic valve | low_side_out | — | — | — | single_source | |
| OEM-X60004-32 | Diagnostic TX (K-line) | serial | — | — | — | single_source | |
| OEM-X60004-33 | Drive-away protection (anti-theft) | — | — | — | — | single_source | |
| OEM-X60004-36 | CAN bus high | can_h | G4XATOMX-A-A28 | CAN H | can_h | single_source | |
| OEM-X60004-37 | CAN bus low | can_l | G4XATOMX-A-A29 | CAN L | can_l | single_source | |
| OEM-X60004-38 | Coolant outlet temperature sensor | temp_in | — | — | — | single_source | |
| OEM-X60004-39 | Coolant outlet temperature sensor ground | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | single_source | |
| OEM-X60004-4 | Cooling fan control | low_side_out | — | — | — | single_source | |
| OEM-X60004-7 | Pedal ground 1 | sensor_ground | G4XATOMX-A-A24 | Sensor Ground | sensor_ground | corroborated | |
| OEM-X60004-8 | Pedal position signal 1 | analog_in | G4XATOMX-A-A33 | Analog Volt 3 | analog_in | corroborated | |
| OEM-X60004-9 | Pedal +5V supply 1 | vref | G4XATOMX-A-A32 | +5V Out | vref | corroborated | |
| OEM-X60005-1 | Ignition coil 3 | ignition_out | G4XATOMX-A-A11 | Ignition 3 | ignition_out | corroborated | |
| OEM-X60005-2 | Ignition coil 2 | ignition_out | G4XATOMX-A-A12 | Ignition 2 | ignition_out | corroborated | |
| OEM-X60005-3 | Ignition coil 1 | ignition_out | G4XATOMX-A-A13 | Ignition 1 | ignition_out | corroborated | |
| OEM-X60005-5 | Ignition ground | ground | G4XATOMX-A-A25 + G4XATOMX-A-A34 + MAIN-R-COIL- | System Ground + System Ground + Relay coil negative (ECU low-side driver) | ground + load | corroborated | |
| OEM-X60005-7 | Ignition coil 6 | ignition_out | — | — | — | corroborated | |
| OEM-X60005-8 | Ignition coil 5 | ignition_out | — | — | — | corroborated | |
| OEM-X60005-9 | Ignition coil 4 | ignition_out | G4XATOMX-A-A10 | Ignition 4 | ignition_out | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-X60001-8 | SP-14V-1 | 0.85 | no route | ECU main power (terminal 87 via main relay) | — | |
| W2 | OEM-X60001-9 | SP-14V-1 | 0.85 | no route | Voltage supply (injector / fuse carrier) | — | |
| W3 | OEM-X60004-26 | MAIN-R-COIL+ | 0.5 | no route | Ignition switch (terminal 15) | — | |
| W4 | NEW-BATT-1 | MAIN-R-IN | 0.85 | no route | Relay contact input (battery + via main fuse) | — | |
| W5 | MAIN-R-COIL- | SP-GND-1 | 0.5 | no route | Relay coil negative (ECU low-side driver) | — | |
| W6 | MAIN-R-OUT | G4XATOMX-A-A5 | 0.85 | no route | Relay contact output (switched +12V bus) | — | |
| W7 | OEM-X60001-4 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W8 | OEM-X60001-5 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W9 | OEM-X60001-6 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W10 | OEM-X60005-5 | SP-GND-1 | 0.85 | no route | Ignition ground | — | |
| W11 | SP-GND-1 | G4XATOMX-A-A25 | 0.85 | no route | System Ground | — | |
| W12 | SP-GND-1 | G4XATOMX-A-A34 | 0.85 | no route | System Ground | — | |
| W13 | OEM-X60002-20 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 1 pre-cat | — | |
| W14 | OEM-X60002-21 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 2 pre-cat | — | |
| W15 | OEM-X60002-22 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 1 post-cat | — | |
| W16 | OEM-X60002-24 | SP-0V-1 | 0.5 | no route | O2 sensor ground, bank 2 post-cat | — | |
| W17 | OEM-X60003-15 | SP-0V-1 | 0.5 | no route | Exhaust camshaft ground | — | |
| W18 | OEM-X60003-17 | SP-0V-1 | 0.5 | no route | MAF ground | — | |
| W19 | OEM-X60003-18 | SP-0V-1 | 0.5 | no route | Intake camshaft ground | — | |
| W20 | OEM-X60003-20 | SP-0V-1 | 0.5 | no route | Throttle ground | — | |
| W21 | OEM-X60003-21 | SP-0V-1 | 0.5 | no route | Crankshaft ground | — | |
| W22 | OEM-X60003-23 | SP-0V-1 | 0.5 | no route | IAT ground | — | |
| W23 | OEM-X60003-25 | SP-0V-1 | 0.5 | no route | ECT ground | — | |
| W24 | OEM-X60003-28 | SP-0V-1 | 0.5 | no route | Oil temperature ground | — | |
| W25 | OEM-X60004-12 | SP-0V-1 | 0.5 | no route | Pedal ground 2 | — | |
| W26 | OEM-X60004-39 | SP-0V-1 | 0.5 | no route | Coolant outlet temperature sensor ground | — | |
| W27 | OEM-X60004-7 | SP-0V-1 | 0.5 | no route | Pedal ground 1 | — | |
| W28 | SP-0V-1 | G4XATOMX-A-A24 | 0.5 | no route | Sensor Ground | — | |
| W29 | OEM-X60003-7 | SP-5V1-1 | 0.5 | no route | Throttle body +5V supply | — | |
| W30 | OEM-X60004-14 | SP-5V1-1 | 0.5 | no route | Pedal +5V supply 2 | — | |
| W31 | OEM-X60004-9 | SP-5V1-1 | 0.5 | no route | Pedal +5V supply 1 | — | |
| W32 | SP-5V1-1 | G4XATOMX-A-A32 | 0.5 | no route | +5V Out | — | |
| W33 | OEM-X60003-8 | G4XATOMX-A-A8 | 0.5 | no route | Crankshaft position | — | |
| W34 | OEM-X60003-2 | G4XATOMX-A-A9 | 0.5 | no route | Exhaust camshaft position | — | |
| W35 | OEM-X60003-5 | G4XATOMX-A-A30 | 0.5 | no route | Intake camshaft position | — | |
| W36 | OEM-X60003-29 | G4XATOMX-A-A6 | 0.5 | no route | Knock sensor, cylinders 1-3 (A) | — | |
| W37 | OEM-X60005-3 | G4XATOMX-A-A13 | 0.5 | no route | Ignition coil 1 | — | |
| W38 | OEM-X60005-2 | G4XATOMX-A-A12 | 0.5 | no route | Ignition coil 2 | — | |
| W39 | OEM-X60005-1 | G4XATOMX-A-A11 | 0.5 | no route | Ignition coil 3 | — | |
| W40 | OEM-X60005-9 | G4XATOMX-A-A10 | 0.5 | no route | Ignition coil 4 | — | |
| W41 | OEM-X60003-33 | G4XATOMX-A-A4 | 0.5 | no route | Injector cylinder 1 | — | |
| W42 | OEM-X60003-34 | G4XATOMX-A-A3 | 0.5 | no route | Injector cylinder 2 | — | |
| W43 | OEM-X60003-35 | G4XATOMX-A-A2 | 0.5 | no route | Injector cylinder 3 | — | |
| W44 | OEM-X60003-36 | G4XATOMX-A-A1 | 0.5 | no route | Injector cylinder 4 | — | |
| W45 | OEM-X60003-37 | G4XATOMX-A-A4 | 0.5 | no route | Injector cylinder 5 | — | |
| W46 | OEM-X60003-38 | G4XATOMX-A-A3 | 0.5 | no route | Injector cylinder 6 | — | |
| W47 | OEM-X60003-48 | SP-SHD-1 | 0.5 | no route | Knock sensor shield | — | |
| W48 | SP-SHD-1 | G4XATOMX-A-A7 | 0.5 | no route | Shield Ground | — | |
| W49 | OEM-X60003-1 | G4XATOMX-A-A17 | 0.5 | no route | Mass air flow (MAF) signal | — | |
| W50 | OEM-X60003-19 | G4XATOMX-A-A22 | 0.5 | no route | Throttle position sensor 1 | — | |
| W51 | OEM-X60004-8 | G4XATOMX-A-A33 | 0.5 | no route | Pedal position signal 1 | — | |
| W52 | OEM-X60003-24 | G4XATOMX-A-A15 | 0.5 | no route | Engine coolant temperature (ECT) | — | |
| W53 | OEM-X60001-1 | G4XATOMX-A-A21 | 0.5 | no route | Injector/unloader relay control (terminal 15) | — | |
| W54 | OEM-X60002-23 | G4XATOMX-A-A20 | 0.5 | no route | Main relay control | — | |
| W55 | OEM-X60004-10 | G4XATOMX-A-A19 | 0.5 | no route | Fuel pump relay control | — | |
| W56 | OEM-X60004-29 | G4XATOMX-A-A18 | 0.5 | no route | A/C relay control | — | |
| W57 | OEM-X60003-22 | G4XATOMX-A-A16 | 0.5 | no route | Intake air temperature (IAT) | — | |
| W58 | OEM-X60004-22 | G4XATOMX-A-A31 | 0.5 | no route | Rear wheel speed input | — | |
| W59 | OEM-X60004-36 | G4XATOMX-A-A28 | 0.5 | no route | CAN bus high | — | |
| W60 | OEM-X60004-37 | G4XATOMX-A-A29 | 0.5 | no route | CAN bus low | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | BMW-E46-MS43-CONN | BMW | E46 DME (MS43) harness connector | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (7)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | REQUIRED_UNMAPPED | OEM-X60003-10 | Required OEM function "Throttle position sensor 2" (analog_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60003-43 | Required OEM function "Throttle motor − (M−)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60003-44 | Required OEM function "Throttle motor + (M+)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60004-13 | Required OEM function "Pedal position signal 2" (analog_in) is not connected to the new ECU. |
| warn | NET_FAMILY | OEM-X60003-5 ↔ G4XATOMX-A-A30 | OEM-X60003-5 "Intake camshaft position" [trigger_in] is wired to G4XATOMX-A-A30 "Digital Input 1" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| info | NET_FAMILY | OEM-X60004-26 ↔ MAIN-R-COIL+ | OEM-X60004-26 "Ignition switch (terminal 15)" [digital_in] is wired to MAIN-R-COIL+ "Relay coil positive (ignition-switched +12V)" [power_in]. Switched supply used as the ignition-on sense. |
| info | UNMAPPED | OEM | 34 optional OEM pins are not mapped: OEM-X60001-9 Voltage supply (injector / fuse carrier); OEM-X60002-1 O2 sensor heater, bank 1 pre-cat; OEM-X60002-13 O2 sensor heater, bank 2 pre-cat; OEM-X60002-14 O2 sensor signal, bank 1 pre-cat; OEM-X60002-15 O2 sensor signal, bank 2 pre-cat; OEM-X60002-16 O2 sensor signal, bank 1 post-cat; OEM-X60002-18 O2 sensor signal, bank 2 post-cat; OEM-X60002-19 O2 sensor heater, bank 2 post-cat; OEM-X60002-7 O2 sensor heater, bank 1 post-cat; OEM-X60003-27 Engine oil temperature; OEM-X60003-30 Knock sensor, cylinders 1-3 (B); OEM-X60003-31 Knock sensor, cylinders 4-6 (A); OEM-X60003-32 Knock sensor, cylinders 4-6 (B); OEM-X60003-40 VANOS intake solenoid; OEM-X60003-41 VANOS exhaust solenoid; OEM-X60003-42 Evap purge valve; OEM-X60003-45 Map-controlled thermostat; OEM-X60003-46 Idle speed control, close; OEM-X60003-47 Idle speed control, open; OEM-X60003-49 DISA intake flap; OEM-X60003-51 Fuel tank leakage diagnostic heater; OEM-X60003-52 Secondary air pump valve; OEM-X60004-17 Engine speed (RPM) output; OEM-X60004-18 Exhaust flap valve control; OEM-X60004-20 Fuel tank leakage diagnostic pump; OEM-X60004-23 Clutch switch input; OEM-X60004-24 Brake light switch input (pin 4); OEM-X60004-28 Brake light switch input (pin 3); OEM-X60004-3 Secondary air pump relay control; OEM-X60004-30 Fuel tank leakage diagnostic valve; OEM-X60004-32 Diagnostic TX (K-line); OEM-X60004-33 Drive-away protection (anti-theft); OEM-X60004-38 Coolant outlet temperature sensor; OEM-X60004-4 Cooling fan control |
Accepted (3)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-X60001-7 | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-X60005-7 | Ignition outputs are a documented capability limit: this ECU has fewer ignition channels than the engine has cylinders, so the remaining coils pair per firing order (wasted spark) and are not wired 1:1. | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-X60005-8 | Ignition outputs are a documented capability limit: this ECU has fewer ignition channels than the engine has cylinders, so the remaining coils pair per firing order (wasted spark) and are not wired 1:1. | mapping-proposal |
Notes
Fit check: needs add-on. Resolve these before building: - No drive-by-wire; needs a cable-throttle conversion or an external DBW controller - Only 4 ignition outputs for 6 cylinders: wasted spark (pair coils per firing order) - Only 4 injector outputs for 6 injectors: batch / semi-sequential injection - CAN emulation for E46 K-bus/CAN is likely (PC Link ships Mini R50-R53/R56 CAN vehicle modes; Link support reports customers use the Mini CAN configuration successfully on E46 non-M3 (MS42/MS43). M3 (S54/MSS54) not covered.) - This car has EWS 3.3 (rolling code) immobilizer; needs a delete/bypass Auto-mapped by auto_map() from the library pin data on 2026-10-23. Review every wire against both manuals before building. Open items: - OEM-X60005 8: Ignition coil 5: no free ignition output on Link G4X AtomX - OEM-X60005 7: Ignition coil 6: no free ignition output on Link G4X AtomX - OEM-X60003 43: Throttle motor − (M−): needs a paired H-bridge on Link G4X AtomX (H-bridge pairing not in the library: set device_pin.bridge_pair from the ECU manual) - OEM-X60003 44: Throttle motor + (M+): needs a paired H-bridge on Link G4X AtomX (H-bridge pairing not in the library: set device_pin.bridge_pair from the ECU manual) - OEM-X60003 10: Throttle position sensor 2: no free tps/analog_0_5 on Link G4X AtomX - OEM-X60004 13: Pedal position signal 2: no free tps/analog_0_5 on Link G4X AtomX Not wired: - OEM-X60001 7: Battery constant (terminal 30): Link G4X AtomX has no battery-constant memory input; not needed - OEM-X60003 30: Knock sensor, cylinders 1-3 (B): no free knock input on Link G4X AtomX - OEM-X60003 31: Knock sensor, cylinders 4-6 (A): no free knock input on Link G4X AtomX - OEM-X60003 32: Knock sensor, cylinders 4-6 (B): no free knock input on Link G4X AtomX - OEM-X60004 3: Secondary air pump relay control: no free relay_control/low_side/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60002 1: O2 sensor heater, bank 1 pre-cat: no free heater_low_side/low_side/relay_control/ls_hs/injector on Link G4X AtomX - OEM-X60002 13: O2 sensor heater, bank 2 pre-cat: no free heater_low_side/low_side/relay_control/ls_hs/injector on Link G4X AtomX - OEM-X60002 19: O2 sensor heater, bank 2 post-cat: no free heater_low_side/low_side/relay_control/ls_hs/injector on Link G4X AtomX - OEM-X60002 7: O2 sensor heater, bank 1 post-cat: no free heater_low_side/low_side/relay_control/ls_hs/injector on Link G4X AtomX - OEM-X60003 51: Fuel tank leakage diagnostic heater: no free heater_low_side/low_side/relay_control/ls_hs/injector on Link G4X AtomX - OEM-X60003 40: VANOS intake solenoid: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60003 41: VANOS exhaust solenoid: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60003 42: Evap purge valve: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60003 45: Map-controlled thermostat: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60003 49: DISA intake flap: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60003 52: Secondary air pump valve: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60004 18: Exhaust flap valve control: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60004 20: Fuel tank leakage diagnostic pump: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60004 30: Fuel tank leakage diagnostic valve: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60004 4: Cooling fan control: no free low_side/relay_control/heater_low_side/ls_hs/injector on Link G4X AtomX - OEM-X60004 17: Engine speed (RPM) output: no free tacho/frequency_out/low_side/ls_hs on Link G4X AtomX - OEM-X60002 14: O2 sensor signal, bank 1 pre-cat: no free o2_narrowband/analog_0_5 on Link G4X AtomX - OEM-X60002 15: O2 sensor signal, bank 2 pre-cat: no free o2_narrowband/analog_0_5 on Link G4X AtomX - OEM-X60002 16: O2 sensor signal, bank 1 post-cat: no free o2_narrowband/analog_0_5 on Link G4X AtomX - OEM-X60002 18: O2 sensor signal, bank 2 post-cat: no free o2_narrowband/analog_0_5 on Link G4X AtomX - OEM-X60003 27: Engine oil temperature: no free thermistor/analog_0_5 on Link G4X AtomX - OEM-X60004 38: Coolant outlet temperature sensor: no free thermistor/analog_0_5 on Link G4X AtomX - OEM-X60004 23: Clutch switch input: no free switch_in/frequency_in/analog_0_5 on Link G4X AtomX - OEM-X60004 24: Brake light switch input (pin 4): no free switch_in/frequency_in/analog_0_5 on Link G4X AtomX - OEM-X60004 28: Brake light switch input (pin 3): no free switch_in/frequency_in/analog_0_5 on Link G4X AtomX - OEM-X60004 32: Diagnostic TX (K-line): no free k_line on Link G4X AtomX - OEM-X60003 46: Idle speed control, close: no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-X60003 47: Idle speed control, open: no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-X60004 33: Drive-away protection (anti-theft): not classified in the library; wire by hand
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | Emtron SL4/SL6/SL8 pinout pages | https://docs.emtronaustralia.com.au/engine-management/wiring/index.html | archive | 2026-10-05 | e52b3da9996a |
| 4 | vendor_doc | Link: G4X AtomX quickstart | https://linkecu.com/documentation/AtomXQuickstartGuide.pdf | archive | 2026-10-05 | 5fa903ea7bdf |
| 3 | community_copy | YourSpec: Link G4X AtomX ECU flying-lead harness wiring list | https://wpm.yourspec.com/projects/view/1462 | — | — | — |
| 3 | forum | rusEFI Mazda Miata 2002 engine wiring | https://github.com/rusefi/rusefi/wiki/Mazda-Miata-2002 | archive | 2026-10-05 | cc3cae670408 |
| 2 | community_copy | ms4x.net: Siemens MS43 Pinout | https://www.ms4x.net/index.php?title=Siemens_MS43_Pinout | — | — | — |
| 2 | community_copy | rusefi wiki: 2002 BMW 325 / 2004 BMW 330Ci E46 DME pinout (M54/MS43) | https://github.com/rusefi/rusefi/wiki/2002-BMW-325-and-2004-BMW-330Ci-E46-DME-pinout | — | — | — |