Mustang GT 2011–14 (Coyote 5.0) → FuelTech FT450 (auto)
Mustang GT 2011–14 (Coyote 5.0) — FuelTech — FT450
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-23
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 6: read the Findings page before cutting any wire |
| Size of the job | 46 wires · 12 connectors · 3 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-C175E-18 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | NEW-KEYON-1 | MAIN-R-COIL+ | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | NEW-BATT-1 | MAIN-R-IN | 5.0 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | MAIN-R-COIL- | SP-GND-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | MAIN-R-OUT | FT450-A-A13 | 5.0 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | SP-GND-1 | FT450-A-A7 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | APP-J-GND1 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | APP-J-GND2 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | OEM-C175E-23 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-C175E-40 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-C175E-49 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-C175E-52 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-C175E-54 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-C175E-67 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-C175E-69 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | TB-J-GND | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | SP-0V-1 | FT450-A-A12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | APP-J-VCC1 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | APP-J-VCC2 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-C175E-17 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-C175E-34 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-C175E-8 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | TB-J-VCC | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | SP-5V1-1 | FT450-A-A14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-C175E-70 | FT450-A-A19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | SP-0V-1 | FT450-A-A18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-C175E-55 | FT450-A-A17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-C175E-1 | FT450-A-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-C175E-62 | FT450-A-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-C175E-46 | FT450-A-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-C175E-3 | FT450-A-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-C175E-2 | FT450-A-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-C175E-31 | FT450-A-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-C175E-61 | FT450-A-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-C175E-16 | FT450-A-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | FT450-A-A6 | NEW-FUELPUMP-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-C175E-10 | FT450-A-A20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-C175E-9 | FT450-A-A21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-C175E-27 | FT450-A-A26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-C175E-47 | FT450-A-A24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | APP-J-SIG1 | FT450-A-A22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | TB-J-TPS1 | FT450-A-A23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | APP-J-SIG2 | FT450-A-A25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-C175E-5 | FT450-A-A3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-C175E-4 | FT450-A-A4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-C175E-7 | FT450-A-A5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | APP-J-VCC1 | APP-J-GND1 | open (OL) | 5 V sensor reference must not touch sensor ground | |
| 2 | APP-J-VCC1 | FT450-A-A7 | open (OL) | 5 V sensor reference must not touch power ground | |
| 3 | FT450-A-A13 | FT450-A-A7 | open (OL) | +12 V supply must not touch power ground | |
| 4 | OEM-C175E-18 | APP-J-GND1 | open (OL) | +12 V supply must not touch sensor ground | |
| 5 | OEM-C175E-18 | FT450-A-A7 | open (OL) | +12 V supply must not touch power ground | |
| 6 | APP-J-GND1 | FT450-A-A13 | open (OL) | sensor ground must not touch +12 V supply | |
| 7 | APP-J-GND1 | NEW-BATT-1 | open (OL) | sensor ground must not touch +12 V supply | |
| 8 | APP-J-GND1 | NEW-KEYON-1 | open (OL) | sensor ground must not touch +12 V supply | |
| 9 | APP-J-VCC1 | FT450-A-A13 | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 10 | APP-J-VCC1 | NEW-BATT-1 | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 11 | APP-J-VCC1 | NEW-KEYON-1 | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 12 | APP-J-VCC1 | OEM-C175E-18 | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 13 | FT450-A-A7 | NEW-BATT-1 | open (OL) | power ground must not touch +12 V supply | |
| 14 | FT450-A-A7 | NEW-KEYON-1 | open (OL) | power ground must not touch +12 V supply |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
APP-J
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| SIG1 | Pedal position 1 | — | W41 | — | 0.5 | FT450-A-A22 | — | — | — |
| VCC1 | Pedal 1 5V supply | — | W18 | — | 0.5 | SP-5V1-1 | — | — | — |
| GND1 | Pedal 1 low ref | — | W7 | — | 0.5 | SP-0V-1 | — | — | — |
| SIG2 | Pedal position 2 | — | W43 | — | 0.5 | FT450-A-A25 | — | — | — |
| VCC2 | Pedal 2 5V supply | — | W19 | — | 0.5 | SP-5V1-1 | — | — | — |
| GND2 | Pedal 2 low ref | — | W8 | — | 0.5 | SP-0V-1 | — | — | — |
FT450-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A1 | Injector 1 (Bank A) | — | W34 | — | 0.5 | OEM-C175E-61 | — | — | — |
| A1 | Injector 1 (Bank A) | — | W28 | — | 0.5 | OEM-C175E-1 | — | — | — |
| A1 | Injector 1 (Bank A) | — | W30 | — | 0.5 | OEM-C175E-46 | — | — | — |
| A1 | Injector 1 (Bank A) | — | W32 | — | 0.5 | OEM-C175E-2 | — | — | — |
| A10 | Ignition 3 | — | — | — | — | — | — | — | — |
| A11 | Ignition 4 | — | — | — | — | — | — | — | — |
| A12 | Signal ground | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| A13 | +12V switched | — | W5 | — | 5.0 | MAIN-R-OUT | — | — | — |
| A14 | +5V sensor supply | — | W24 | — | 0.5 | SP-5V1-1 | — | — | — |
| A15 | CAN A LOW | — | — | — | — | — | — | — | — |
| A16 | CAN A HIGH | — | — | — | — | — | — | — | — |
| A17 | Phase input (cam) | — | W27 | — | 0.5 | OEM-C175E-55 | — | — | — |
| A18 | RPM signal (crank −) | — | W26 | — | 0.5 | SP-0V-1 | — | — | — |
| A19 | RPM signal (crank +) | — | W25 | — | 0.5 | OEM-C175E-70 | — | — | — |
| A2 | Injector 2 (Bank A) | — | W29 | — | 0.5 | OEM-C175E-62 | — | — | — |
| A2 | Injector 2 (Bank A) | — | W31 | — | 0.5 | OEM-C175E-3 | — | — | — |
| A2 | Injector 2 (Bank A) | — | W33 | — | 0.5 | OEM-C175E-31 | — | — | — |
| A2 | Injector 2 (Bank A) | — | W35 | — | 0.5 | OEM-C175E-16 | — | — | — |
| A20 | White input 1 | — | W37 | — | 0.5 | OEM-C175E-10 | — | — | — |
| A21 | White input 2 | — | W38 | — | 0.5 | OEM-C175E-9 | — | — | — |
| A22 | White input 3 (TPS) | — | W41 | — | 0.5 | APP-J-SIG1 | — | — | — |
| A23 | White input 4 (oil pressure) | — | W42 | — | 0.5 | TB-J-TPS1 | — | — | — |
| A24 | White input 5 (water temp) | — | W40 | — | 0.5 | OEM-C175E-47 | — | — | — |
| A25 | White input 6 (fuel pressure) | — | W43 | — | 0.5 | APP-J-SIG2 | — | — | — |
| A26 | White input 7 (air temp) | — | W39 | — | 0.5 | OEM-C175E-27 | — | — | — |
| A3 | Aux 1 | — | W44 | — | 0.5 | OEM-C175E-5 | — | — | — |
| A4 | Aux 2 | — | W45 | — | 0.5 | OEM-C175E-4 | — | — | — |
| A5 | Aux 3 | — | W46 | — | 0.5 | OEM-C175E-7 | — | — | — |
| A6 | Aux 4 (fuel pump / relays) | — | W36 | — | 0.5 | NEW-FUELPUMP-1 | — | — | — |
| A7 | Power ground | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| A8 | Ignition 1 | — | — | — | — | — | — | — | — |
| A9 | Ignition 2 | — | — | — | — | — | — | — | — |
MAIN-R
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| COIL+ | Relay coil positive (ignition-switched +12V) | — | W2 | — | 0.5 | NEW-KEYON-1 | — | — | — |
| COIL- | Relay coil negative (ECU low-side driver) | — | W4 | — | 0.5 | SP-GND-1 | — | — | — |
| IN | Relay contact input (battery + via main fuse) | — | W3 | — | 5.0 | NEW-BATT-1 | — | — | — |
| OUT | Relay contact output (switched +12V bus) | — | W5 | — | 5.0 | FT450-A-A13 | — | — | — |
NEW-BATT
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W3 | — | 5.0 | MAIN-R-IN | — | — | — |
NEW-FUELPUMP
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W36 | — | 0.5 | FT450-A-A6 | — | — | — |
NEW-KEYON
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W2 | — | 0.5 | MAIN-R-COIL+ | — | — | — |
OEM-C175E
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Fuel injector driver 1 (INJ 1) | — | W28 | — | 0.5 | FT450-A-A1 | — | — | — |
| 2 | Fuel injector driver 5 (INJ 5) | — | W32 | — | 0.5 | FT450-A-A1 | — | — | — |
| 3 | Fuel injector driver 4 (INJ 4) | — | W31 | — | 0.5 | FT450-A-A2 | — | — | — |
| 4 | Variable camshaft timing valve 2 (VCT2) | — | W45 | — | 0.5 | FT450-A-A4 | — | — | — |
| 5 | Variable camshaft timing valve 1 (VCT1) | — | W44 | — | 0.5 | FT450-A-A3 | — | — | — |
| 6 | Variable camshaft timing valve 4 (VCT4) | — | — | — | — | — | — | — | — |
| 7 | Variable camshaft timing valve 3 (VCT3) | — | W46 | — | 0.5 | FT450-A-A5 | — | — | — |
| 8 | Electronic throttle control reference (ETCREF) | — | W22 | — | 0.5 | SP-5V1-1 | — | — | — |
| 9 | Throttle position 2 (TP2-PS) | — | W38 | — | 0.5 | FT450-A-A21 | — | — | — |
| 10 | Throttle position 1 (TP1-NS) | — | W37 | — | 0.5 | FT450-A-A20 | — | — | — |
| 11 | — | — | — | — | — | — | — | — | — |
| 12 | — | — | — | — | — | — | — | — | — |
| 13 | — | — | — | — | — | — | — | — | — |
| 14 | — | — | — | — | — | — | — | — | — |
| 15 | — | — | — | — | — | — | — | — | — |
| 16 | Fuel injector driver 8 (INJ 8) | — | W35 | — | 0.5 | FT450-A-A2 | — | — | — |
| 17 | Buffered power supply sensors (VBPWR) | — | W20 | — | 0.5 | SP-5V1-1 | — | — | — |
| 18 | PCM power feed (VPWR, fused) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 19 | — | — | — | — | — | — | — | — | — |
| 20 | Universal HEGO 1st reference (UREF-11) | — | — | — | — | — | — | — | — |
| 21 | Universal HEGO 2nd reference (UREF-21) | — | — | — | — | — | — | — | — |
| 22 | — | — | — | — | — | — | — | — | — |
| 23 | Electronic throttle control return (ETCRTN) | — | W9 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | — | — | — | — | — | — | — | — | — |
| 25 | — | — | — | — | — | — | — | — | — |
| 26 | — | — | — | — | — | — | — | — | — |
| 27 | Intake air temperature (IAT) | — | W39 | — | 0.5 | FT450-A-A26 | — | — | — |
| 28 | — | — | — | — | — | — | — | — | — |
| 29 | — | — | — | — | — | — | — | — | — |
| 30 | Engine oil level switch (EOL) | — | — | — | — | — | — | — | — |
| 31 | Fuel injector driver 6 (INJ 6) | — | W33 | — | 0.5 | FT450-A-A2 | — | — | — |
| 32 | — | — | — | — | — | — | — | — | — |
| 33 | — | — | — | — | — | — | — | — | — |
| 34 | Voltage reference engine (VREF) | — | W21 | — | 0.5 | SP-5V1-1 | — | — | — |
| 35 | Universal HEGO 1st pump current (UO2SIP-11) | — | — | — | — | — | — | — | — |
| 36 | Universal HEGO 2nd pump current (UO2SIP-21) | — | — | — | — | — | — | — | — |
| 37 | — | — | — | — | — | — | — | — | — |
| 38 | — | — | — | — | — | — | — | — | — |
| 39 | Crankshaft sensor shield/drain | — | — | — | — | — | — | — | — |
| 40 | VR sensor return (VRSRTN) | — | W10 | — | 0.5 | SP-0V-1 | — | — | — |
| 41 | Camshaft position bank 2 (CMP2) | — | — | — | — | — | — | — | — |
| 42 | Camshaft position bank 2 exhaust (CMP2 EX) | — | — | — | — | — | — | — | — |
| 43 | — | — | — | — | — | — | — | — | — |
| 44 | Intake manifold monitor (IMM) | — | — | — | — | — | — | — | — |
| 45 | Intake port deactivation valve position | — | — | — | — | — | — | — | — |
| 46 | Fuel injector driver 3 (INJ 3) | — | W30 | — | 0.5 | FT450-A-A1 | — | — | — |
| 47 | Cylinder head temperature (CHT) | — | W40 | — | 0.5 | FT450-A-A24 | — | — | — |
| 48 | Oil pressure switch | — | — | — | — | — | — | — | — |
| 49 | Signal return engine #2 | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| 50 | Universal HEGO 1st sense (UO2SN-11) | — | — | — | — | — | — | — | — |
| 51 | Universal HEGO 2nd sense (UO2SN-21) | — | — | — | — | — | — | — | — |
| 52 | Knock sensor 1 bank 1 return (KS1−) | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| 53 | Knock sensor 1 bank 1 signal (KS1+) | — | — | — | — | — | — | — | — |
| 54 | VR sensor return (VRSRTN) | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 55 | Camshaft position bank 1 (CMP1) | — | W27 | — | 0.5 | FT450-A-A17 | — | — | — |
| 56 | Camshaft position bank 1 exhaust (CMP1 EX) | — | — | — | — | — | — | — | — |
| 57 | Oil pressure switch (MTX) | — | — | — | — | — | — | — | — |
| 58 | — | — | — | — | — | — | — | — | — |
| 59 | Manifold heater (CE511) or IMRC charge-motion valve (CE315, 5.0L RHD) | — | — | — | — | — | — | — | — |
| 60 | IMTV monitor (CE923) or intake manifold tuning valve (CE316, 5.0L RHD) | — | — | — | — | — | — | — | — |
| 61 | Fuel injector driver 7 (INJ 7) | — | W34 | — | 0.5 | FT450-A-A1 | — | — | — |
| 62 | Fuel injector driver 2 (INJ 2) | — | W29 | — | 0.5 | FT450-A-A2 | — | — | — |
| 63 | — | — | — | — | — | — | — | — | — |
| 64 | — | — | — | — | — | — | — | — | — |
| 65 | — | — | — | — | — | — | — | — | — |
| 66 | — | — | — | — | — | — | — | — | — |
| 67 | Knock sensor 2 bank 1 return (KS2−) | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 68 | Knock sensor 2 bank 1 signal (KS2+) | — | — | — | — | — | — | — | — |
| 69 | Crankshaft position return (CKP−) | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 70 | Crankshaft position (CKP+) | — | W25 | — | 0.5 | FT450-A-A19 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W7 | — | 0.5 | APP-J-GND1 | — | — | — |
| 1 | — | — | W8 | — | 0.5 | APP-J-GND2 | — | — | — |
| 1 | — | — | W9 | — | 0.5 | OEM-C175E-23 | — | — | — |
| 1 | — | — | W10 | — | 0.5 | OEM-C175E-40 | — | — | — |
| 1 | — | — | W11 | — | 0.5 | OEM-C175E-49 | — | — | — |
| 1 | — | — | W12 | — | 0.5 | OEM-C175E-52 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | OEM-C175E-54 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | OEM-C175E-67 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | OEM-C175E-69 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | TB-J-GND | — | — | — |
| 1 | — | — | W17 | — | 0.5 | FT450-A-A12 | — | — | — |
| 1 | — | — | W26 | — | 0.5 | FT450-A-A18 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-C175E-18 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W18 | — | 0.5 | APP-J-VCC1 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | APP-J-VCC2 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | OEM-C175E-17 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | OEM-C175E-34 | — | — | — |
| 1 | — | — | W22 | — | 0.5 | OEM-C175E-8 | — | — | — |
| 1 | — | — | W23 | — | 0.5 | TB-J-VCC | — | — | — |
| 1 | — | — | W24 | — | 0.5 | FT450-A-A14 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W6 | — | 0.85 | FT450-A-A7 | — | — | — |
| 1 | — | — | W4 | — | 0.5 | MAIN-R-COIL- | — | — | — |
TB-J
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| TPS1 | Throttle position 1 | — | W42 | — | 0.5 | FT450-A-A23 | — | — | — |
| TPS2 | Throttle position 2 | — | — | — | — | — | — | — | — |
| VCC | Throttle 5V supply | — | W23 | — | 0.5 | SP-5V1-1 | — | — | — |
| GND | Throttle sensor ground | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| M+ | Throttle motor + | — | — | — | — | — | — | — | — |
| M- | Throttle motor − | — | — | — | — | — | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-C175E-1 | Fuel injector driver 1 (INJ 1) | injector_out | FT450-A-A1 | Injector 1 (Bank A) | injector_out | corroborated | |
| OEM-C175E-10 | Throttle position 1 (TP1-NS) | analog_in | FT450-A-A20 | White input 1 | analog_in | corroborated | |
| OEM-C175E-16 | Fuel injector driver 8 (INJ 8) | injector_out | FT450-A-A2 | Injector 2 (Bank A) | injector_out | corroborated | |
| OEM-C175E-17 | Buffered power supply sensors (VBPWR) | vref | APP-J-VCC1 + APP-J-VCC2 + FT450-A-A14 + TB-J-VCC | Pedal 1 5V supply + Pedal 2 5V supply + +5V sensor supply + Throttle 5V supply | power_in + vref | corroborated | |
| OEM-C175E-18 | PCM power feed (VPWR, fused) | power_in | — | — | — | corroborated | |
| OEM-C175E-2 | Fuel injector driver 5 (INJ 5) | injector_out | FT450-A-A1 | Injector 1 (Bank A) | injector_out | corroborated | |
| OEM-C175E-20 | Universal HEGO 1st reference (UREF-11) | wb_vgnd | — | — | — | corroborated | |
| OEM-C175E-21 | Universal HEGO 2nd reference (UREF-21) | wb_vgnd | — | — | — | corroborated | |
| OEM-C175E-23 | Electronic throttle control return (ETCRTN) | sensor_ground | APP-J-GND1 + APP-J-GND2 + FT450-A-A12 + FT450-A-A18 + TB-J-GND | Pedal 1 low ref + Pedal 2 low ref + Signal ground + RPM signal (crank −) + Throttle sensor ground | sensor_ground + trigger_in | corroborated | |
| OEM-C175E-27 | Intake air temperature (IAT) | temp_in | FT450-A-A26 | White input 7 (air temp) | temp_in | corroborated | |
| OEM-C175E-3 | Fuel injector driver 4 (INJ 4) | injector_out | FT450-A-A2 | Injector 2 (Bank A) | injector_out | corroborated | |
| OEM-C175E-30 | Engine oil level switch (EOL) | digital_in | — | — | — | corroborated | |
| OEM-C175E-31 | Fuel injector driver 6 (INJ 6) | injector_out | FT450-A-A2 | Injector 2 (Bank A) | injector_out | corroborated | |
| OEM-C175E-34 | Voltage reference engine (VREF) | vref | APP-J-VCC1 + APP-J-VCC2 + FT450-A-A14 + TB-J-VCC | Pedal 1 5V supply + Pedal 2 5V supply + +5V sensor supply + Throttle 5V supply | power_in + vref | corroborated | |
| OEM-C175E-35 | Universal HEGO 1st pump current (UO2SIP-11) | wb_ip | — | — | — | corroborated | |
| OEM-C175E-36 | Universal HEGO 2nd pump current (UO2SIP-21) | wb_ip | — | — | — | corroborated | |
| OEM-C175E-39 | Crankshaft sensor shield/drain | shield | — | — | — | corroborated | |
| OEM-C175E-4 | Variable camshaft timing valve 2 (VCT2) | low_side_out | FT450-A-A4 | Aux 2 | low_side_out | corroborated | |
| OEM-C175E-40 | VR sensor return (VRSRTN) | sensor_ground | APP-J-GND1 + APP-J-GND2 + FT450-A-A12 + FT450-A-A18 + TB-J-GND | Pedal 1 low ref + Pedal 2 low ref + Signal ground + RPM signal (crank −) + Throttle sensor ground | sensor_ground + trigger_in | corroborated | |
| OEM-C175E-41 | Camshaft position bank 2 (CMP2) | trigger_in | — | — | — | corroborated | |
| OEM-C175E-42 | Camshaft position bank 2 exhaust (CMP2 EX) | trigger_in | — | — | — | corroborated | |
| OEM-C175E-44 | Intake manifold monitor (IMM) | analog_in | — | — | — | corroborated | |
| OEM-C175E-45 | Intake port deactivation valve position | analog_in | — | — | — | corroborated | |
| OEM-C175E-46 | Fuel injector driver 3 (INJ 3) | injector_out | FT450-A-A1 | Injector 1 (Bank A) | injector_out | corroborated | |
| OEM-C175E-47 | Cylinder head temperature (CHT) | temp_in | FT450-A-A24 | White input 5 (water temp) | temp_in | corroborated | |
| OEM-C175E-48 | Oil pressure switch | digital_in | — | — | — | corroborated | |
| OEM-C175E-49 | Signal return engine #2 | sensor_ground | APP-J-GND1 + APP-J-GND2 + FT450-A-A12 + FT450-A-A18 + TB-J-GND | Pedal 1 low ref + Pedal 2 low ref + Signal ground + RPM signal (crank −) + Throttle sensor ground | sensor_ground + trigger_in | corroborated | |
| OEM-C175E-5 | Variable camshaft timing valve 1 (VCT1) | low_side_out | FT450-A-A3 | Aux 1 | low_side_out | corroborated | |
| OEM-C175E-50 | Universal HEGO 1st sense (UO2SN-11) | wb_vs | — | — | — | corroborated | |
| OEM-C175E-51 | Universal HEGO 2nd sense (UO2SN-21) | wb_vs | — | — | — | corroborated | |
| OEM-C175E-52 | Knock sensor 1 bank 1 return (KS1−) | sensor_ground | APP-J-GND1 + APP-J-GND2 + FT450-A-A12 + FT450-A-A18 + TB-J-GND | Pedal 1 low ref + Pedal 2 low ref + Signal ground + RPM signal (crank −) + Throttle sensor ground | sensor_ground + trigger_in | corroborated | |
| OEM-C175E-53 | Knock sensor 1 bank 1 signal (KS1+) | knock_in | — | — | — | corroborated | |
| OEM-C175E-54 | VR sensor return (VRSRTN) | sensor_ground | APP-J-GND1 + APP-J-GND2 + FT450-A-A12 + FT450-A-A18 + TB-J-GND | Pedal 1 low ref + Pedal 2 low ref + Signal ground + RPM signal (crank −) + Throttle sensor ground | sensor_ground + trigger_in | corroborated | |
| OEM-C175E-55 | Camshaft position bank 1 (CMP1) | trigger_in | FT450-A-A17 | Phase input (cam) | trigger_in | corroborated | |
| OEM-C175E-56 | Camshaft position bank 1 exhaust (CMP1 EX) | trigger_in | — | — | — | corroborated | |
| OEM-C175E-57 | Oil pressure switch (MTX) | digital_in | — | — | — | corroborated | |
| OEM-C175E-59 | Manifold heater (CE511) or IMRC charge-motion valve (CE315, 5.0L RHD) | — | — | — | — | corroborated | |
| OEM-C175E-6 | Variable camshaft timing valve 4 (VCT4) | low_side_out | — | — | — | corroborated | |
| OEM-C175E-60 | IMTV monitor (CE923) or intake manifold tuning valve (CE316, 5.0L RHD) | — | — | — | — | corroborated | |
| OEM-C175E-61 | Fuel injector driver 7 (INJ 7) | injector_out | FT450-A-A1 | Injector 1 (Bank A) | injector_out | corroborated | |
| OEM-C175E-62 | Fuel injector driver 2 (INJ 2) | injector_out | FT450-A-A2 | Injector 2 (Bank A) | injector_out | corroborated | |
| OEM-C175E-67 | Knock sensor 2 bank 1 return (KS2−) | sensor_ground | APP-J-GND1 + APP-J-GND2 + FT450-A-A12 + FT450-A-A18 + TB-J-GND | Pedal 1 low ref + Pedal 2 low ref + Signal ground + RPM signal (crank −) + Throttle sensor ground | sensor_ground + trigger_in | corroborated | |
| OEM-C175E-68 | Knock sensor 2 bank 1 signal (KS2+) | knock_in | — | — | — | corroborated | |
| OEM-C175E-69 | Crankshaft position return (CKP−) | sensor_ground | APP-J-GND1 + APP-J-GND2 + FT450-A-A12 + FT450-A-A18 + TB-J-GND | Pedal 1 low ref + Pedal 2 low ref + Signal ground + RPM signal (crank −) + Throttle sensor ground | sensor_ground + trigger_in | corroborated | |
| OEM-C175E-7 | Variable camshaft timing valve 3 (VCT3) | low_side_out | FT450-A-A5 | Aux 3 | low_side_out | corroborated | |
| OEM-C175E-70 | Crankshaft position (CKP+) | trigger_in | FT450-A-A19 | RPM signal (crank +) | trigger_in | corroborated | |
| OEM-C175E-8 | Electronic throttle control reference (ETCREF) | vref | APP-J-VCC1 + APP-J-VCC2 + FT450-A-A14 + TB-J-VCC | Pedal 1 5V supply + Pedal 2 5V supply + +5V sensor supply + Throttle 5V supply | power_in + vref | corroborated | |
| OEM-C175E-9 | Throttle position 2 (TP2-PS) | analog_in | FT450-A-A21 | White input 2 | analog_in | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-C175E-18 | SP-14V-1 | 0.85 | no route | PCM power feed (VPWR, fused) | — | |
| W2 | NEW-KEYON-1 | MAIN-R-COIL+ | 0.5 | no route | Relay coil positive (ignition-switched +12V) | — | |
| W3 | NEW-BATT-1 | MAIN-R-IN | 5.0 | no route | Relay contact input (battery + via main fuse) | — | |
| W4 | MAIN-R-COIL- | SP-GND-1 | 0.5 | no route | Relay coil negative (ECU low-side driver) | — | |
| W5 | MAIN-R-OUT | FT450-A-A13 | 5.0 | no route | Relay contact output (switched +12V bus) | — | |
| W6 | SP-GND-1 | FT450-A-A7 | 0.85 | no route | Power ground | — | |
| W7 | APP-J-GND1 | SP-0V-1 | 0.5 | no route | Pedal 1 low ref | — | |
| W8 | APP-J-GND2 | SP-0V-1 | 0.5 | no route | Pedal 2 low ref | — | |
| W9 | OEM-C175E-23 | SP-0V-1 | 0.5 | no route | Electronic throttle control return (ETCRTN) | — | |
| W10 | OEM-C175E-40 | SP-0V-1 | 0.5 | no route | VR sensor return (VRSRTN) | — | |
| W11 | OEM-C175E-49 | SP-0V-1 | 0.5 | no route | Signal return engine #2 | — | |
| W12 | OEM-C175E-52 | SP-0V-1 | 0.5 | no route | Knock sensor 1 bank 1 return (KS1−) | — | |
| W13 | OEM-C175E-54 | SP-0V-1 | 0.5 | no route | VR sensor return (VRSRTN) | — | |
| W14 | OEM-C175E-67 | SP-0V-1 | 0.5 | no route | Knock sensor 2 bank 1 return (KS2−) | — | |
| W15 | OEM-C175E-69 | SP-0V-1 | 0.5 | no route | Crankshaft position return (CKP−) | — | |
| W16 | TB-J-GND | SP-0V-1 | 0.5 | no route | Throttle sensor ground | — | |
| W17 | SP-0V-1 | FT450-A-A12 | 0.5 | no route | Signal ground | — | |
| W18 | APP-J-VCC1 | SP-5V1-1 | 0.5 | no route | Pedal 1 5V supply | — | |
| W19 | APP-J-VCC2 | SP-5V1-1 | 0.5 | no route | Pedal 2 5V supply | — | |
| W20 | OEM-C175E-17 | SP-5V1-1 | 0.5 | no route | Buffered power supply sensors (VBPWR) | — | |
| W21 | OEM-C175E-34 | SP-5V1-1 | 0.5 | no route | Voltage reference engine (VREF) | — | |
| W22 | OEM-C175E-8 | SP-5V1-1 | 0.5 | no route | Electronic throttle control reference (ETCREF) | — | |
| W23 | TB-J-VCC | SP-5V1-1 | 0.5 | no route | Throttle 5V supply | — | |
| W24 | SP-5V1-1 | FT450-A-A14 | 0.5 | no route | +5V sensor supply | — | |
| W25 | OEM-C175E-70 | FT450-A-A19 | 0.5 | no route | Crankshaft position (CKP+) | — | |
| W26 | SP-0V-1 | FT450-A-A18 | 0.5 | no route | RPM signal (crank −) | — | |
| W27 | OEM-C175E-55 | FT450-A-A17 | 0.5 | no route | Camshaft position bank 1 (CMP1) | — | |
| W28 | OEM-C175E-1 | FT450-A-A1 | 0.5 | no route | Fuel injector driver 1 (INJ 1) | — | |
| W29 | OEM-C175E-62 | FT450-A-A2 | 0.5 | no route | Fuel injector driver 2 (INJ 2) | — | |
| W30 | OEM-C175E-46 | FT450-A-A1 | 0.5 | no route | Fuel injector driver 3 (INJ 3) | — | |
| W31 | OEM-C175E-3 | FT450-A-A2 | 0.5 | no route | Fuel injector driver 4 (INJ 4) | — | |
| W32 | OEM-C175E-2 | FT450-A-A1 | 0.5 | no route | Fuel injector driver 5 (INJ 5) | — | |
| W33 | OEM-C175E-31 | FT450-A-A2 | 0.5 | no route | Fuel injector driver 6 (INJ 6) | — | |
| W34 | OEM-C175E-61 | FT450-A-A1 | 0.5 | no route | Fuel injector driver 7 (INJ 7) | — | |
| W35 | OEM-C175E-16 | FT450-A-A2 | 0.5 | no route | Fuel injector driver 8 (INJ 8) | — | |
| W36 | FT450-A-A6 | NEW-FUELPUMP-1 | 0.5 | no route | Aux 4 (fuel pump / relays) | — | |
| W37 | OEM-C175E-10 | FT450-A-A20 | 0.5 | no route | Throttle position 1 (TP1-NS) | — | |
| W38 | OEM-C175E-9 | FT450-A-A21 | 0.5 | no route | Throttle position 2 (TP2-PS) | — | |
| W39 | OEM-C175E-27 | FT450-A-A26 | 0.5 | no route | Intake air temperature (IAT) | — | |
| W40 | OEM-C175E-47 | FT450-A-A24 | 0.5 | no route | Cylinder head temperature (CHT) | — | |
| W41 | APP-J-SIG1 | FT450-A-A22 | 0.5 | no route | Pedal position 1 | — | |
| W42 | TB-J-TPS1 | FT450-A-A23 | 0.5 | no route | Throttle position 1 | — | |
| W43 | APP-J-SIG2 | FT450-A-A25 | 0.5 | no route | Pedal position 2 | — | |
| W44 | OEM-C175E-5 | FT450-A-A3 | 0.5 | no route | Variable camshaft timing valve 1 (VCT1) | — | |
| W45 | OEM-C175E-4 | FT450-A-A4 | 0.5 | no route | Variable camshaft timing valve 2 (VCT2) | — | |
| W46 | OEM-C175E-7 | FT450-A-A5 | 0.5 | no route | Variable camshaft timing valve 3 (VCT3) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | COYOTE-PCM-A | — | 2011–14 Mustang GT PCM 70-way connector C175E (housing P/N unknown) | 1.000 | ea |
| connector | FORD-COYOTE-APP | Ford | Ford Coyote accelerator pedal plug (P/N unknown; 6-way) | 1.000 | ea |
| connector | FORD-COYOTE-TB | Ford | Ford Coyote throttle body plug (P/N unknown; 6-way) | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| dbw_motor | TB | Throttle motor + | — | — | — | — | — |
| dbw_motor | TB | Throttle motor − | — | — | — | — | — |
| dbw_pedal | APP | Pedal position 1 | 0_5v | FT450-A-A22 | White input 3 (TPS) | analog_0_5 | — |
| dbw_pedal | APP | Pedal position 2 | 0_5v | FT450-A-A25 | White input 6 (fuel pressure) | analog_0_5 | — |
| dbw_tps | TB | Throttle position 1 | 0_5v | FT450-A-A23 | White input 4 (oil pressure) | analog_0_5 | — |
| dbw_tps | TB | Throttle position 2 | 0_5v | — | — | — | — |
Findings
Open (9)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | PHYS_REQUIRED_OPEN | TB-J-M+ | TB-J-M+ "Throttle motor +" is required but not wired. |
| error | PHYS_REQUIRED_OPEN | TB-J-M- | TB-J-M- "Throttle motor −" is required but not wired. |
| error | PHYS_REQUIRED_OPEN | TB-J-TPS2 | TB-J-TPS2 "Throttle position 2" is required but not wired. |
| error | REQUIRED_UNMAPPED | OEM-C175E-41 | Required OEM function "Camshaft position bank 2 (CMP2)" (trigger_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-C175E-42 | Required OEM function "Camshaft position bank 2 exhaust (CMP2 EX)" (trigger_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-C175E-56 | Required OEM function "Camshaft position bank 1 exhaust (CMP1 EX)" (trigger_in) is not connected to the new ECU. |
| warn | DATASET_GAP | Mustang GT PCM C175E | 22 of 70 cavities on Mustang GT PCM C175E have no pin data (11,12,13,14,15,19,22,24,25,26,28,29,32,33,37,38,43,58,63,64,65,66). Anything there is invisible to these checks. |
| info | NET_FAMILY | OEM-C175E-69 ↔ FT450-A-A18 | OEM-C175E-69 "Crankshaft position return (CKP−)" [sensor_ground] is wired to FT450-A-A18 "RPM signal (crank −)" [trigger_in]. Trigger return tied to sensor/trigger ground: correct for single-ended trigger inputs. |
| info | UNMAPPED | OEM | 17 optional OEM pins are not mapped: OEM-C175E-20 Universal HEGO 1st reference (UREF-11); OEM-C175E-21 Universal HEGO 2nd reference (UREF-21); OEM-C175E-30 Engine oil level switch (EOL); OEM-C175E-35 Universal HEGO 1st pump current (UO2SIP-11); OEM-C175E-36 Universal HEGO 2nd pump current (UO2SIP-21); OEM-C175E-39 Crankshaft sensor shield/drain; OEM-C175E-44 Intake manifold monitor (IMM); OEM-C175E-45 Intake port deactivation valve position; OEM-C175E-48 Oil pressure switch; OEM-C175E-50 Universal HEGO 1st sense (UO2SN-11); OEM-C175E-51 Universal HEGO 2nd sense (UO2SN-21); OEM-C175E-53 Knock sensor 1 bank 1 signal (KS1+); OEM-C175E-57 Oil pressure switch (MTX); OEM-C175E-59 Manifold heater (CE511) or IMRC charge-motion valve (CE315, 5.0L RHD); OEM-C175E-6 Variable camshaft timing valve 4 (VCT4); OEM-C175E-60 IMTV monitor (CE923) or intake manifold tuning valve (CE316, 5.0L RHD); OEM-C175E-68 Knock sensor 2 bank 1 signal (KS2+) |
Accepted (0)
| Code | Subject | Reason | By |
|---|
Notes
Fit check: needs add-on. Resolve these before building: - No drive-by-wire; needs a cable-throttle conversion or an external DBW controller - Needs CAN (ford_mustang_2011_14); not documented for this ECU - No knock input; the stock knock sensor would be unused - Only 4 ignition outputs for 8 cylinders: wasted spark (pair coils per firing order) - Only 6 injector outputs for 8 injectors: batch / semi-sequential injection - second cam not wired: no sequential/VVT - This car has PATS immobilizer; needs a delete/bypass Auto-mapped by auto_map() from the library pin data on 2026-10-23. Review every wire against both manuals before building. Open items: - OEM-C175E 56: Camshaft position bank 1 exhaust (CMP1 EX): no free cam_vr/cam_hall/frequency_in input on FuelTech FT450 - OEM-C175E 41: Camshaft position bank 2 (CMP2): no free cam_vr/cam_hall/frequency_in input on FuelTech FT450 - OEM-C175E 42: Camshaft position bank 2 exhaust (CMP2 EX): no free cam_vr/cam_hall/frequency_in input on FuelTech FT450 - TB-J M+: Throttle motor +: needs a paired H-bridge on FuelTech FT450 (H-bridge pairing not in the library: set device_pin.bridge_pair from the ECU manual) - TB-J M-: Throttle motor −: needs a paired H-bridge on FuelTech FT450 (H-bridge pairing not in the library: set device_pin.bridge_pair from the ECU manual) - TB-J TPS2: Throttle position 2: no free analog_0_5 on FuelTech FT450 Not wired: - OEM-C175E 53: Knock sensor 1 bank 1 signal (KS1+): no free knock input on FuelTech FT450 - OEM-C175E 68: Knock sensor 2 bank 1 signal (KS2+): no free knock input on FuelTech FT450 - OEM-C175E 39: Crankshaft sensor shield/drain: no shield pin on FuelTech FT450 - OEM-C175E 6: Variable camshaft timing valve 4 (VCT4): no free low_side/relay_control/heater_low_side/ls_hs/injector on FuelTech FT450 - OEM-C175E 35: Universal HEGO 1st pump current (UO2SIP-11): no free wb_ip on FuelTech FT450 - OEM-C175E 36: Universal HEGO 2nd pump current (UO2SIP-21): no free wb_ip on FuelTech FT450 - OEM-C175E 50: Universal HEGO 1st sense (UO2SN-11): no free wb_vs on FuelTech FT450 - OEM-C175E 51: Universal HEGO 2nd sense (UO2SN-21): no free wb_vs on FuelTech FT450 - OEM-C175E 20: Universal HEGO 1st reference (UREF-11): no free wb_vgnd on FuelTech FT450 - OEM-C175E 21: Universal HEGO 2nd reference (UREF-21): no free wb_vgnd on FuelTech FT450 - OEM-C175E 44: Intake manifold monitor (IMM): no free map/analog_0_5 on FuelTech FT450 - OEM-C175E 45: Intake port deactivation valve position: no free analog_0_5 on FuelTech FT450 - OEM-C175E 30: Engine oil level switch (EOL): no free switch_in/frequency_in/analog_0_5 on FuelTech FT450 - OEM-C175E 48: Oil pressure switch: no free switch_in/frequency_in/analog_0_5 on FuelTech FT450 - OEM-C175E 57: Oil pressure switch (MTX): no free switch_in/frequency_in/analog_0_5 on FuelTech FT450 - OEM-C175E 59: Manifold heater (CE511) or IMRC charge-motion valve (CE315, 5.0L RHD): not classified in the library; wire by hand - OEM-C175E 60: IMTV monitor (CE923) or intake manifold tuning valve (CE316, 5.0L RHD): not classified in the library; wire by hand
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | Emtron SL4/SL6/SL8 pinout pages | https://docs.emtronaustralia.com.au/engine-management/wiring/index.html | archive | 2026-10-05 | e52b3da9996a |
| 4 | vendor_doc | Ford Performance Gen 1 Coyote control pack (M-6017-A504VB) instruction sheet | — | — | — | — |
| 4 | vendor_doc | FuelTech FT450/FT550 ready harness manual (4 & 6 cylinder) — FT450 Connector A pinout | http://ftmanager.fueltech.com.br/downloads/manual/Portugues/Chicote_pronto_FT450-FT550.pdf | — | — | — |
| 3 | community_copy | iihs.net: 2011 Mustang factory Wiring Diagrams (Cell 24 Electronic Engine Controls, 5.0L) | https://iihs.net/fsm/?d=711 | — | — | — |
| 3 | forum | rusEFI Mazda Miata 2002 engine wiring | https://github.com/rusefi/rusefi/wiki/Mazda-Miata-2002 | archive | 2026-10-05 | cc3cae670408 |
| 2 | community_copy | rusEFI OEM-Docs: Coyote C175E pinout (Pin/Circuit/Gauge/Circuit Function/Qualifier) | https://raw.githubusercontent.com/rusefi/rusefi_documentation/master/OEM-Docs/Ford/Coyote-175e-pinout-B.png | — | — | — |