Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
100%
Stock ECU being replaced
P8-C1-18 Injector 2
P8-C1-37 Injector 1
P8-C1-54 Injector 3
GND
OEM-A
Stock ECU being replaced
11Injectors 2 & 6 (No.20)
12Injectors 1 & 4 (No.10)
25Injectors 3 & 5 (No.30)
26Power ground (E01/E02)
P8-C1-26 Water Temp
P8-C1-12 Lambda Signal
0V sensor
P8-C1-48 Throttle Wiper
OEM-B
Stock ECU being replaced
4Coolant temp (THW)
6Primary O2 sensor (OX1)
9Sensor ground (E1)
11Throttle position sensor (VTA)
P8-C1-11 Undriven Wheel (must)
P8-C1-45 Air Temp
P8-C1-5 Aux Out 2
P8-C1-29 Left Driven Wheel
P8-C1-13 Map2/ALS/Ana1 On/Off
P8-C1-14 Traction Wet/Dry
EFI main relay power (+B)
EFI main relay power (second feed) (+B1)
P8-C1-31 Launch Button
OEM-D
Stock ECU being replaced
2Karman-vortex AFM signal (KS)
3Intake air temp (THA)
4EFI main relay control (M-REL)
9Vehicle speed sensor (SPD)
10A/C compressor request (A/C)
11Starter signal (STA)
12EFI main relay power (+B)
13EFI main relay power (second feed) (+B1)
22Neutral start switch (NSW)
P8
P8-C1
P8
5Aux Out 2
11Undriven Wheel (must)
12Lambda Signal
13Map2/ALS/Ana1 On/Off
14Traction Wet/Dry
15Power Ground
18Injector 2
1912 Volts
26Water Temp
29Left Driven Wheel
31Launch Button
34Power Ground
37Injector 1
41Fuel Pump Relay
45Air Temp
46Signal Ground
47Signal Ground
48Throttle Wiper
49Lambda Earth
51Signal Ground
54Injector 3
55Power Ground
OEM-D-4 EFI main relay control (M-REL)
OEM-D-2 Karman-vortex AFM signal (KS)
OEM-B-6 Primary O2 sensor (OX1)
OEM-D-10 A/C compressor request (A/C)
OEM-D-11 Starter signal (STA)
GND
OEM-A-11 Injectors 2 & 6 (No.20)
12 Volts
OEM-B-4 Coolant temp (THW)
OEM-D-9 Vehicle speed sensor (SPD)
OEM-D-22 Neutral start switch (NSW)
GND
OEM-A-12 Injectors 1 & 4 (No.10)
NEW-FUELPUMP
OEM-D-3 Intake air temp (THA)
0V sensor
0V sensor
OEM-B-11 Throttle position sensor (VTA)
0V sensor
0V sensor
OEM-A-25 Injectors 3 & 5 (No.30)
GND
SP-GND · 5 pins
◯New feed: NEW-FUELPUMP
SP-0V · 6 pins
SP-14V · 4 pins
Press enter or space to select a node. You can then use the arrow keys to move the node around. Press delete to remove it and escape to cancel.
Press enter or space to select an edge. You can then press delete to remove it or escape to cancel.