Toyota 86 (ZN6, FA20) → DTAFast T2i (auto)
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 9: read the Findings page before cutting any wire |
| Size of the job | 45 wires · 9 connectors · 2 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Terminals | 3-1447221-4 |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-A33-1 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-A34-6 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | T2I-C1-31 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-A33-2 | T2I-C1-21 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-A33-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-A34-1 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-A34-2 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-A34-3 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | OEM-A36-3 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-A36-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | SP-GND-1 | T2I-C1-13 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | SP-GND-1 | T2I-C1-14 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-A33-29 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-A34-27 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-A35-29 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-A35-30 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-A36-29 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | SP-0V-1 | T2I-C1-28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | SP-0V-1 | T2I-C1-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-A34-34 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-A35-21 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-A35-22 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-A36-19 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | SP-5V1-1 | T2I-C1-27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-A34-16 | T2I-C1-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-A34-14 | T2I-C1-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-A36-21 | T2I-C1-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-A36-10 | T2I-C1-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-A35-13 | T2I-C1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-A35-12 | T2I-C1-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-A35-11 | T2I-C1-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-A33-20 | T2I-C1-26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-A34-5 | T2I-C1-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-A33-22 | T2I-C1-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-A34-20 | T2I-C1-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-A35-31 | T2I-C1-23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-A36-28 | T2I-C1-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-A35-23 | T2I-C1-33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-A36-18 | T2I-C1-34 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-A36-30 | T2I-C1-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-A33-12 | T2I-C1-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-A33-14 | T2I-C1-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-A33-15 | T2I-C1-30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-A33-19 | T2I-C1-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-A33-18 | T2I-C1-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | T2I-C1-21 | T2I-C1-13 | open (OL) | +12 V supply must not touch power ground | |
| 2 | T2I-C1-21 | T2I-C1-28 | open (OL) | +12 V supply must not touch sensor ground | |
| 3 | T2I-C1-31 | T2I-C1-13 | open (OL) | +12 V supply must not touch power ground | |
| 4 | T2I-C1-31 | T2I-C1-28 | open (OL) | +12 V supply must not touch sensor ground | |
| 5 | T2I-C1-13 | T2I-C1-27 | open (OL) | power ground must not touch 5 V sensor reference | |
| 6 | T2I-C1-21 | T2I-C1-27 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 7 | T2I-C1-28 | T2I-C1-27 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 8 | T2I-C1-31 | T2I-C1-27 | open (OL) | +12 V supply must not touch 5 V sensor reference |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
OEM-A33
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | ECU power (+B2, main relay) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 12 | Intake air temperature (THA, in MAF) | — | W41 | — | 0.5 | T2I-C1-32 | — | — | — |
| 14 | Starter signal (STSW2) | — | W42 | — | 0.5 | T2I-C1-11 | — | — | — |
| 15 | Clutch switch (CLSW) | — | W43 | — | 0.5 | T2I-C1-30 | — | — | — |
| 16 | Neutral switch (NSW) | — | — | — | — | — | — | — | — |
| 17 | Starter signal (STSW2) | — | — | — | — | — | — | — | — |
| 18 | CAN low (CANL) | — | W45 | — | 0.5 | T2I-C1-17 | — | — | — |
| 19 | CAN high (CANH) | — | W44 | — | 0.5 | T2I-C1-16 | — | — | — |
| 2 | Battery constant (BATT, memory) | — | W4 | — | 0.85 | T2I-C1-21 | — | — | — |
| 20 | Blower relay (HB) | — | W32 | — | 0.5 | T2I-C1-26 | — | — | — |
| 22 | Mass air flow (VG) | — | W34 | — | 0.5 | T2I-C1-20 | — | — | — |
| 27 | Ignition switch sense (IGSW, IG2 relay) | — | — | — | — | — | — | — | — |
| 28 | Shield ground (SLE2) | — | — | — | — | — | — | — | — |
| 29 | MAF sensor ground (E2G) | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 3 | Stop light switch (ST1-) | — | — | — | — | — | — | — | — |
| 4 | Power ground (EC) | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 7 | Stop light switch (STP) | — | — | — | — | — | — | — | — |
| 8 | A/C pressure sensor (ACP) | — | — | — | — | — | — | — | — |
OEM-A34
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Power ground (E03) | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 11 | DI injector confirmation (IJF1) | — | — | — | — | — | — | — | — |
| 13 | High-pressure fuel pump spill valve (FPF) | — | — | — | — | — | — | — | — |
| 14 | VVT cam sensor exhaust bank 1 (EV1+) | — | W26 | — | 0.5 | T2I-C1-12 | — | — | — |
| 15 | VVT cam sensor intake bank 2 (VV2+) | — | — | — | — | — | — | — | — |
| 16 | Crank position (NE+) | — | W25 | — | 0.5 | T2I-C1-19 | — | — | — |
| 17 | Knock sensor 2 (KNK2) | — | — | — | — | — | — | — | — |
| 18 | A/F ratio sensor (A1A-) | — | — | — | — | — | — | — | — |
| 19 | A/F ratio sensor (A1A+) | — | — | — | — | — | — | — | — |
| 2 | Power ground (E04) | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 20 | Manifold absolute pressure (PIM) | — | W35 | — | 0.5 | T2I-C1-22 | — | — | — |
| 21 | Heated oxygen sensor (OX1B, rear) | — | — | — | — | — | — | — | — |
| 25 | VVT cam sensor exhaust bank 2 (EV2+) | — | — | — | — | — | — | — | — |
| 26 | VVT cam sensor intake bank 1 (VV1+) | — | — | — | — | — | — | — | — |
| 27 | Crank position return (NE-) | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 28 | Knock sensor 1 (KNK1) | — | — | — | — | — | — | — | — |
| 29 | Shield ground (EKNK) | — | — | — | — | — | — | — | — |
| 3 | Power ground (E05) | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 30 | Shield ground (SLE1) | — | — | — | — | — | — | — | — |
| 31 | DI injector confirmation (IJF2) | — | — | — | — | — | — | — | — |
| 32 | High-pressure fuel pump spill valve (FPD) | — | — | — | — | — | — | — | — |
| 34 | OCV power source (VCV, 5V) | — | W20 | — | 0.5 | SP-5V1-1 | — | — | — |
| 35 | Shield ground (SLE3) | — | — | — | — | — | — | — | — |
| 5 | A/F ratio sensor heater (HA1A) | — | W33 | — | 0.5 | T2I-C1-15 | — | — | — |
| 6 | ECU power (+B, main relay) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 9 | Fuel pressure sensor (PR) | — | — | — | — | — | — | — | — |
OEM-A35
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Canister vent valve (VPMP) | — | — | — | — | — | — | — | — |
| 10 | Fuel pump control monitor (DI) | — | — | — | — | — | — | — | — |
| 11 | Cooling fan relay 3 (FAN1) | — | W31 | — | 0.5 | T2I-C1-18 | — | — | — |
| 12 | Cooling fan relay 2 (FAN2) | — | W30 | — | 0.5 | T2I-C1-10 | — | — | — |
| 13 | EFI main relay 1 (SSHUT) | — | W29 | — | 0.5 | T2I-C1-1 | — | — | — |
| 15 | Tachometer output (TACH) | — | — | — | — | — | — | — | — |
| 17 | ETCS relay (MCR) | — | — | — | — | — | — | — | — |
| 19 | Fuel pump control (FPC) | — | — | — | — | — | — | — | — |
| 20 | Canister pressure sensor (PPMP) | — | — | — | — | — | — | — | — |
| 21 | Accelerator pedal 5V supply (VCPA) | — | W21 | — | 0.5 | SP-5V1-1 | — | — | — |
| 22 | Accelerator pedal 5V supply (VCP2) | — | W22 | — | 0.5 | SP-5V1-1 | — | — | — |
| 23 | Accelerator pedal position (VPA) | — | W38 | — | 0.5 | T2I-C1-33 | — | — | — |
| 26 | Starter signal (STA) | — | — | — | — | — | — | — | — |
| 29 | Accelerator pedal ground (EPA) | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 30 | Accelerator pedal ground (EPA2) | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 31 | Accelerator pedal position 2 (VPA2) | — | W36 | — | 0.5 | T2I-C1-23 | — | — | — |
| 35 | A/C clutch relay (AC) | — | — | — | — | — | — | — | — |
| 5 | Injector relay (IREL) | — | — | — | — | — | — | — | — |
| 7 | ETCS relay (+BM) | — | — | — | — | — | — | — | — |
| 8 | Leak detection pump (MPMP) | — | — | — | — | — | — | — | — |
OEM-A36
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Throttle actuator motor - (M-) | — | — | — | — | — | — | — | — |
| 10 | Ignition coil 2 (IGT2) | — | W28 | — | 0.5 | T2I-C1-6 | — | — | — |
| 11 | Purge valve (PRG) | — | — | — | — | — | — | — | — |
| 12 | Injector 1 port (#10) | — | — | — | — | — | — | — | — |
| 13 | Injector 4 port (#40) | — | — | — | — | — | — | — | — |
| 14 | Injector 1 direct (#1) | — | — | — | — | — | — | — | — |
| 16 | OCV intake bank 2 (OC2) | — | — | — | — | — | — | — | — |
| 17 | OCV intake bank 1 (OC1) | — | — | — | — | — | — | — | — |
| 18 | Throttle position (VTA1) | — | W39 | — | 0.5 | T2I-C1-34 | — | — | — |
| 19 | Sensor 5V supply (VC) | — | W23 | — | 0.5 | SP-5V1-1 | — | — | — |
| 2 | Throttle actuator motor + (M+) | — | — | — | — | — | — | — | — |
| 20 | Oil temperature (OT) | — | — | — | — | — | — | — | — |
| 21 | Ignition coil 1 (IGT1) | — | W27 | — | 0.5 | T2I-C1-3 | — | — | — |
| 22 | Injector 2 port (#20) | — | — | — | — | — | — | — | — |
| 23 | Injector 4 direct (#4) | — | — | — | — | — | — | — | — |
| 24 | Injector 3 direct (#3) | — | — | — | — | — | — | — | — |
| 25 | Injector 2 direct (#2) | — | — | — | — | — | — | — | — |
| 28 | Throttle position 2 (VTA2) | — | W37 | — | 0.5 | T2I-C1-25 | — | — | — |
| 29 | Sensor ground (E1) | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 3 | Power ground (E02) | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 30 | Engine coolant temperature (THW) | — | W40 | — | 0.5 | T2I-C1-24 | — | — | — |
| 31 | Ignition coil 3 (IGT3) | — | — | — | — | — | — | — | — |
| 32 | Injector 3 port (#30) | — | — | — | — | — | — | — | — |
| 4 | Power ground (E01) | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | OCV exhaust bank 2 (OE2) | — | — | — | — | — | — | — | — |
| 6 | Heated oxygen sensor heater (HT1B) | — | — | — | — | — | — | — | — |
| 7 | OCV exhaust bank 1 (OE1) | — | — | — | — | — | — | — | — |
| 8 | Ignition coil 4 (IGT4) | — | — | — | — | — | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W13 | — | 0.5 | OEM-A33-29 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | OEM-A34-27 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | OEM-A35-29 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-A35-30 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | OEM-A36-29 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | T2I-C1-28 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | T2I-C1-29 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-A33-1 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-A34-6 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | T2I-C1-31 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W20 | — | 0.5 | OEM-A34-34 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | OEM-A35-21 | — | — | — |
| 1 | — | — | W22 | — | 0.5 | OEM-A35-22 | — | — | — |
| 1 | — | — | W23 | — | 0.5 | OEM-A36-19 | — | — | — |
| 1 | — | — | W24 | — | 0.5 | T2I-C1-27 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W10 | — | 0.85 | OEM-A36-4 | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-A33-4 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-A34-1 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-A34-2 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | OEM-A34-3 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | OEM-A36-3 | — | — | — |
| 1 | — | — | W11 | — | 0.85 | T2I-C1-13 | — | — | — |
| 1 | — | — | W12 | — | 0.85 | T2I-C1-14 | — | — | — |
T2I-C1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | PWM 1 | — | W29 | — | 0.5 | OEM-A35-13 | — | — | — |
| 2 | Lambda Nernst Voltage | — | — | — | — | — | — | — | — |
| 3 | Coil 1 | — | W27 | — | 0.5 | OEM-A36-21 | — | — | — |
| 4 | Lambda VGND | — | — | — | — | — | — | — | — |
| 5 | Lambda Pump Current | — | — | — | — | — | — | — | — |
| 6 | Coil 2 | — | W28 | — | 0.5 | OEM-A36-10 | — | — | — |
| 7 | Lambda Trim Resistor | — | — | — | — | — | — | — | — |
| 8 | — | — | — | — | — | — | — | — | — |
| 9 | — | — | — | — | — | — | — | — | — |
| 10 | PWM 2 | — | W30 | — | 0.5 | OEM-A35-12 | — | — | — |
| 11 | Digital 1 | — | W42 | — | 0.5 | OEM-A33-14 | — | — | — |
| 12 | Wheel 1 | — | W26 | — | 0.5 | OEM-A34-14 | — | — | — |
| 13 | Power Ground 1 | — | W11 | — | 0.85 | SP-GND-1 | — | — | — |
| 14 | Power Ground 2 | — | W12 | — | 0.85 | SP-GND-1 | — | — | — |
| 15 | Lambda Heater Negative | — | W33 | — | 0.5 | OEM-A34-5 | — | — | — |
| 16 | CAN High | — | W44 | — | 0.5 | OEM-A33-19 | — | — | — |
| 17 | CAN Low | — | W45 | — | 0.5 | OEM-A33-18 | — | — | — |
| 18 | PWM 3 | — | W31 | — | 0.5 | OEM-A35-11 | — | — | — |
| 19 | Crank | — | W25 | — | 0.5 | OEM-A34-16 | — | — | — |
| 20 | Analogue 1 | — | W34 | — | 0.5 | OEM-A33-22 | — | — | — |
| 21 | Permanent 12v | — | W4 | — | 0.85 | OEM-A33-2 | — | — | — |
| 22 | Analogue 2 | — | W35 | — | 0.5 | OEM-A34-20 | — | — | — |
| 23 | Analogue 3 | — | W36 | — | 0.5 | OEM-A35-31 | — | — | — |
| 24 | Thermistor 1 | — | W40 | — | 0.5 | OEM-A36-30 | — | — | — |
| 25 | Analogue 4 | — | W37 | — | 0.5 | OEM-A36-28 | — | — | — |
| 26 | PWM 4 | — | W32 | — | 0.5 | OEM-A33-20 | — | — | — |
| 27 | 5v Output | — | W24 | — | 0.5 | SP-5V1-1 | — | — | — |
| 28 | Sensor Ground | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 29 | Sensor Ground | — | W19 | — | 0.5 | SP-0V-1 | — | — | — |
| 30 | Digital 2 | — | W43 | — | 0.5 | OEM-A33-15 | — | — | — |
| 31 | Ignition 12v In | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 32 | Thermistor 2 | — | W41 | — | 0.5 | OEM-A33-12 | — | — | — |
| 33 | Analogue 5 | — | W38 | — | 0.5 | OEM-A35-23 | — | — | — |
| 34 | Analogue 6 | — | W39 | — | 0.5 | OEM-A36-18 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-A33-1 | ECU power (+B2, main relay) | power_in | T2I-C1-31 | Ignition 12v In | power_in | single_source | |
| OEM-A33-12 | Intake air temperature (THA, in MAF) | temp_in | T2I-C1-32 | Thermistor 2 | temp_in | single_source | |
| OEM-A33-14 | Starter signal (STSW2) | digital_in | T2I-C1-11 | Digital 1 | digital_in | single_source | |
| OEM-A33-15 | Clutch switch (CLSW) | digital_in | T2I-C1-30 | Digital 2 | digital_in | single_source | |
| OEM-A33-16 | Neutral switch (NSW) | digital_in | — | — | — | single_source | |
| OEM-A33-17 | Starter signal (STSW2) | digital_in | — | — | — | single_source | |
| OEM-A33-18 | CAN low (CANL) | can_l | T2I-C1-17 | CAN Low | can_l | single_source | |
| OEM-A33-19 | CAN high (CANH) | can_h | T2I-C1-16 | CAN High | can_h | single_source | |
| OEM-A33-2 | Battery constant (BATT, memory) | power_in | T2I-C1-21 | Permanent 12v | power_in | single_source | |
| OEM-A33-20 | Blower relay (HB) | low_side_out | T2I-C1-26 | PWM 4 | low_side_out | single_source | |
| OEM-A33-22 | Mass air flow (VG) | analog_in | T2I-C1-20 | Analogue 1 | analog_in | single_source | |
| OEM-A33-27 | Ignition switch sense (IGSW, IG2 relay) | digital_in | — | — | — | single_source | |
| OEM-A33-28 | Shield ground (SLE2) | shield | — | — | — | single_source | |
| OEM-A33-29 | MAF sensor ground (E2G) | sensor_ground | T2I-C1-28 + T2I-C1-29 | Sensor Ground + Sensor Ground | sensor_ground | single_source | |
| OEM-A33-3 | Stop light switch (ST1-) | digital_in | — | — | — | single_source | |
| OEM-A33-4 | Power ground (EC) | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-A33-7 | Stop light switch (STP) | digital_in | — | — | — | single_source | |
| OEM-A33-8 | A/C pressure sensor (ACP) | analog_in | — | — | — | single_source | |
| OEM-A34-1 | Power ground (E03) | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-A34-11 | DI injector confirmation (IJF1) | analog_in | — | — | — | single_source | |
| OEM-A34-13 | High-pressure fuel pump spill valve (FPF) | low_side_out | — | — | — | single_source | |
| OEM-A34-14 | VVT cam sensor exhaust bank 1 (EV1+) | trigger_in | T2I-C1-12 | Wheel 1 | digital_in | single_source | |
| OEM-A34-15 | VVT cam sensor intake bank 2 (VV2+) | trigger_in | — | — | — | single_source | |
| OEM-A34-16 | Crank position (NE+) | trigger_in | T2I-C1-19 | Crank | trigger_in | single_source | |
| OEM-A34-17 | Knock sensor 2 (KNK2) | knock_in | — | — | — | single_source | |
| OEM-A34-18 | A/F ratio sensor (A1A-) | — | — | — | — | single_source | |
| OEM-A34-19 | A/F ratio sensor (A1A+) | — | — | — | — | single_source | |
| OEM-A34-2 | Power ground (E04) | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-A34-20 | Manifold absolute pressure (PIM) | analog_in | T2I-C1-22 | Analogue 2 | analog_in | single_source | |
| OEM-A34-21 | Heated oxygen sensor (OX1B, rear) | lambda_nb_in | — | — | — | single_source | |
| OEM-A34-25 | VVT cam sensor exhaust bank 2 (EV2+) | trigger_in | — | — | — | single_source | |
| OEM-A34-26 | VVT cam sensor intake bank 1 (VV1+) | trigger_in | — | — | — | single_source | |
| OEM-A34-27 | Crank position return (NE-) | sensor_ground | T2I-C1-28 + T2I-C1-29 | Sensor Ground + Sensor Ground | sensor_ground | single_source | |
| OEM-A34-28 | Knock sensor 1 (KNK1) | knock_in | — | — | — | single_source | |
| OEM-A34-29 | Shield ground (EKNK) | shield | — | — | — | single_source | |
| OEM-A34-3 | Power ground (E05) | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-A34-30 | Shield ground (SLE1) | shield | — | — | — | single_source | |
| OEM-A34-31 | DI injector confirmation (IJF2) | analog_in | — | — | — | single_source | |
| OEM-A34-32 | High-pressure fuel pump spill valve (FPD) | low_side_out | — | — | — | single_source | |
| OEM-A34-34 | OCV power source (VCV, 5V) | vref | T2I-C1-27 | 5v Output | vref | single_source | |
| OEM-A34-35 | Shield ground (SLE3) | shield | — | — | — | single_source | |
| OEM-A34-5 | A/F ratio sensor heater (HA1A) | low_side_out | T2I-C1-15 | Lambda Heater Negative | low_side_out | single_source | |
| OEM-A34-6 | ECU power (+B, main relay) | power_in | T2I-C1-31 | Ignition 12v In | power_in | single_source | |
| OEM-A34-9 | Fuel pressure sensor (PR) | analog_in | — | — | — | single_source | |
| OEM-A35-1 | Canister vent valve (VPMP) | low_side_out | — | — | — | single_source | |
| OEM-A35-10 | Fuel pump control monitor (DI) | analog_in | — | — | — | single_source | |
| OEM-A35-11 | Cooling fan relay 3 (FAN1) | low_side_out | T2I-C1-18 | PWM 3 | low_side_out | single_source | |
| OEM-A35-12 | Cooling fan relay 2 (FAN2) | low_side_out | T2I-C1-10 | PWM 2 | low_side_out | single_source | |
| OEM-A35-13 | EFI main relay 1 (SSHUT) | low_side_out | T2I-C1-1 | PWM 1 | low_side_out | single_source | |
| OEM-A35-15 | Tachometer output (TACH) | tacho_out | — | — | — | single_source | |
| OEM-A35-17 | ETCS relay (MCR) | low_side_out | — | — | — | single_source | |
| OEM-A35-19 | Fuel pump control (FPC) | low_side_out | — | — | — | single_source | |
| OEM-A35-20 | Canister pressure sensor (PPMP) | analog_in | — | — | — | single_source | |
| OEM-A35-21 | Accelerator pedal 5V supply (VCPA) | vref | T2I-C1-27 | 5v Output | vref | single_source | |
| OEM-A35-22 | Accelerator pedal 5V supply (VCP2) | vref | T2I-C1-27 | 5v Output | vref | single_source | |
| OEM-A35-23 | Accelerator pedal position (VPA) | analog_in | T2I-C1-33 | Analogue 5 | analog_in | single_source | |
| OEM-A35-26 | Starter signal (STA) | digital_in | — | — | — | single_source | |
| OEM-A35-29 | Accelerator pedal ground (EPA) | sensor_ground | T2I-C1-28 + T2I-C1-29 | Sensor Ground + Sensor Ground | sensor_ground | single_source | |
| OEM-A35-30 | Accelerator pedal ground (EPA2) | sensor_ground | T2I-C1-28 + T2I-C1-29 | Sensor Ground + Sensor Ground | sensor_ground | single_source | |
| OEM-A35-31 | Accelerator pedal position 2 (VPA2) | analog_in | T2I-C1-23 | Analogue 3 | analog_in | single_source | |
| OEM-A35-35 | A/C clutch relay (AC) | low_side_out | — | — | — | single_source | |
| OEM-A35-5 | Injector relay (IREL) | low_side_out | — | — | — | single_source | |
| OEM-A35-7 | ETCS relay (+BM) | low_side_out | — | — | — | single_source | |
| OEM-A35-8 | Leak detection pump (MPMP) | low_side_out | — | — | — | single_source | |
| OEM-A36-1 | Throttle actuator motor - (M-) | hbridge_out | — | — | — | single_source | |
| OEM-A36-10 | Ignition coil 2 (IGT2) | ignition_out | T2I-C1-6 | Coil 2 | ignition_out | single_source | |
| OEM-A36-11 | Purge valve (PRG) | low_side_out | — | — | — | single_source | |
| OEM-A36-12 | Injector 1 port (#10) | injector_out | — | — | — | single_source | |
| OEM-A36-13 | Injector 4 port (#40) | injector_out | — | — | — | single_source | |
| OEM-A36-14 | Injector 1 direct (#1) | injector_out | — | — | — | single_source | |
| OEM-A36-16 | OCV intake bank 2 (OC2) | low_side_out | — | — | — | single_source | |
| OEM-A36-17 | OCV intake bank 1 (OC1) | low_side_out | — | — | — | single_source | |
| OEM-A36-18 | Throttle position (VTA1) | analog_in | T2I-C1-34 | Analogue 6 | analog_in | single_source | |
| OEM-A36-19 | Sensor 5V supply (VC) | vref | T2I-C1-27 | 5v Output | vref | single_source | |
| OEM-A36-2 | Throttle actuator motor + (M+) | hbridge_out | — | — | — | single_source | |
| OEM-A36-20 | Oil temperature (OT) | temp_in | — | — | — | single_source | |
| OEM-A36-21 | Ignition coil 1 (IGT1) | ignition_out | T2I-C1-3 | Coil 1 | ignition_out | single_source | |
| OEM-A36-22 | Injector 2 port (#20) | injector_out | — | — | — | single_source | |
| OEM-A36-23 | Injector 4 direct (#4) | injector_out | — | — | — | single_source | |
| OEM-A36-24 | Injector 3 direct (#3) | injector_out | — | — | — | single_source | |
| OEM-A36-25 | Injector 2 direct (#2) | injector_out | — | — | — | single_source | |
| OEM-A36-28 | Throttle position 2 (VTA2) | analog_in | T2I-C1-25 | Analogue 4 | analog_in | single_source | |
| OEM-A36-29 | Sensor ground (E1) | sensor_ground | T2I-C1-28 + T2I-C1-29 | Sensor Ground + Sensor Ground | sensor_ground | single_source | |
| OEM-A36-3 | Power ground (E02) | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-A36-30 | Engine coolant temperature (THW) | temp_in | T2I-C1-24 | Thermistor 1 | temp_in | single_source | |
| OEM-A36-31 | Ignition coil 3 (IGT3) | ignition_out | — | — | — | single_source | |
| OEM-A36-32 | Injector 3 port (#30) | injector_out | — | — | — | single_source | |
| OEM-A36-4 | Power ground (E01) | ground | T2I-C1-13 + T2I-C1-14 | Power Ground 1 + Power Ground 2 | ground | single_source | |
| OEM-A36-5 | OCV exhaust bank 2 (OE2) | low_side_out | — | — | — | single_source | |
| OEM-A36-6 | Heated oxygen sensor heater (HT1B) | low_side_out | — | — | — | single_source | |
| OEM-A36-7 | OCV exhaust bank 1 (OE1) | low_side_out | — | — | — | single_source | |
| OEM-A36-8 | Ignition coil 4 (IGT4) | ignition_out | — | — | — | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-A33-1 | SP-14V-1 | 0.85 | no route | ECU power (+B2, main relay) | — | |
| W2 | OEM-A34-6 | SP-14V-1 | 0.85 | no route | ECU power (+B, main relay) | — | |
| W3 | SP-14V-1 | T2I-C1-31 | 0.85 | no route | Ignition 12v In | — | |
| W4 | OEM-A33-2 | T2I-C1-21 | 0.85 | no route | Battery constant (BATT, memory) | — | |
| W5 | OEM-A33-4 | SP-GND-1 | 0.85 | no route | Power ground (EC) | — | |
| W6 | OEM-A34-1 | SP-GND-1 | 0.85 | no route | Power ground (E03) | — | |
| W7 | OEM-A34-2 | SP-GND-1 | 0.85 | no route | Power ground (E04) | — | |
| W8 | OEM-A34-3 | SP-GND-1 | 0.85 | no route | Power ground (E05) | — | |
| W9 | OEM-A36-3 | SP-GND-1 | 0.85 | no route | Power ground (E02) | — | |
| W10 | OEM-A36-4 | SP-GND-1 | 0.85 | no route | Power ground (E01) | — | |
| W11 | SP-GND-1 | T2I-C1-13 | 0.85 | no route | Power Ground 1 | — | |
| W12 | SP-GND-1 | T2I-C1-14 | 0.85 | no route | Power Ground 2 | — | |
| W13 | OEM-A33-29 | SP-0V-1 | 0.5 | no route | MAF sensor ground (E2G) | — | |
| W14 | OEM-A34-27 | SP-0V-1 | 0.5 | no route | Crank position return (NE-) | — | |
| W15 | OEM-A35-29 | SP-0V-1 | 0.5 | no route | Accelerator pedal ground (EPA) | — | |
| W16 | OEM-A35-30 | SP-0V-1 | 0.5 | no route | Accelerator pedal ground (EPA2) | — | |
| W17 | OEM-A36-29 | SP-0V-1 | 0.5 | no route | Sensor ground (E1) | — | |
| W18 | SP-0V-1 | T2I-C1-28 | 0.5 | no route | Sensor Ground | — | |
| W19 | SP-0V-1 | T2I-C1-29 | 0.5 | no route | Sensor Ground | — | |
| W20 | OEM-A34-34 | SP-5V1-1 | 0.5 | no route | OCV power source (VCV, 5V) | — | |
| W21 | OEM-A35-21 | SP-5V1-1 | 0.5 | no route | Accelerator pedal 5V supply (VCPA) | — | |
| W22 | OEM-A35-22 | SP-5V1-1 | 0.5 | no route | Accelerator pedal 5V supply (VCP2) | — | |
| W23 | OEM-A36-19 | SP-5V1-1 | 0.5 | no route | Sensor 5V supply (VC) | — | |
| W24 | SP-5V1-1 | T2I-C1-27 | 0.5 | no route | 5v Output | — | |
| W25 | OEM-A34-16 | T2I-C1-19 | 0.5 | no route | Crank position (NE+) | — | |
| W26 | OEM-A34-14 | T2I-C1-12 | 0.5 | no route | VVT cam sensor exhaust bank 1 (EV1+) | — | |
| W27 | OEM-A36-21 | T2I-C1-3 | 0.5 | no route | Ignition coil 1 (IGT1) | — | |
| W28 | OEM-A36-10 | T2I-C1-6 | 0.5 | no route | Ignition coil 2 (IGT2) | — | |
| W29 | OEM-A35-13 | T2I-C1-1 | 0.5 | no route | EFI main relay 1 (SSHUT) | — | |
| W30 | OEM-A35-12 | T2I-C1-10 | 0.5 | no route | Cooling fan relay 2 (FAN2) | — | |
| W31 | OEM-A35-11 | T2I-C1-18 | 0.5 | no route | Cooling fan relay 3 (FAN1) | — | |
| W32 | OEM-A33-20 | T2I-C1-26 | 0.5 | no route | Blower relay (HB) | — | |
| W33 | OEM-A34-5 | T2I-C1-15 | 0.5 | no route | A/F ratio sensor heater (HA1A) | — | |
| W34 | OEM-A33-22 | T2I-C1-20 | 0.5 | no route | Mass air flow (VG) | — | |
| W35 | OEM-A34-20 | T2I-C1-22 | 0.5 | no route | Manifold absolute pressure (PIM) | — | |
| W36 | OEM-A35-31 | T2I-C1-23 | 0.5 | no route | Accelerator pedal position 2 (VPA2) | — | |
| W37 | OEM-A36-28 | T2I-C1-25 | 0.5 | no route | Throttle position 2 (VTA2) | — | |
| W38 | OEM-A35-23 | T2I-C1-33 | 0.5 | no route | Accelerator pedal position (VPA) | — | |
| W39 | OEM-A36-18 | T2I-C1-34 | 0.5 | no route | Throttle position (VTA1) | — | |
| W40 | OEM-A36-30 | T2I-C1-24 | 0.5 | no route | Engine coolant temperature (THW) | — | |
| W41 | OEM-A33-12 | T2I-C1-32 | 0.5 | no route | Intake air temperature (THA, in MAF) | — | |
| W42 | OEM-A33-14 | T2I-C1-11 | 0.5 | no route | Starter signal (STSW2) | — | |
| W43 | OEM-A33-15 | T2I-C1-30 | 0.5 | no route | Clutch switch (CLSW) | — | |
| W44 | OEM-A33-19 | T2I-C1-16 | 0.5 | no route | CAN high (CANH) | — | |
| W45 | OEM-A33-18 | T2I-C1-17 | 0.5 | no route | CAN low (CANL) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 4-1437290-0 | TE | Superseal 1.0 34-way plug, Key 1 | 1.000 | ea |
| terminal | 3-1447221-4 | TE | Superseal 1.0 socket terminal, 20 AWG (0.5 sq mm) | 28.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (12)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | DBW_SENSOR_INPUT | tps | Only 1 throttle-position track(s) found. An electronic throttle needs two (main and sub) so the ECU can cross-check them. |
| error | REQUIRED_UNMAPPED | OEM-A36-1 | Required OEM function "Throttle actuator motor - (M-)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-A36-12 | Required OEM function "Injector 1 port (#10)" (injector_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-A36-13 | Required OEM function "Injector 4 port (#40)" (injector_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-A36-2 | Required OEM function "Throttle actuator motor + (M+)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-A36-22 | Required OEM function "Injector 2 port (#20)" (injector_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-A36-31 | Required OEM function "Ignition coil 3 (IGT3)" (ignition_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-A36-32 | Required OEM function "Injector 3 port (#30)" (injector_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-A36-8 | Required OEM function "Ignition coil 4 (IGT4)" (ignition_out) is not connected to the new ECU. |
| warn | DATASET_GAP | T2i C1 | 2 of 34 cavities on T2i C1 have no pin data (8,9). Anything there is invisible to these checks. |
| warn | NET_FAMILY | OEM-A34-14 ↔ T2I-C1-12 | OEM-A34-14 "VVT cam sensor exhaust bank 1 (EV1+)" [trigger_in] is wired to T2I-C1-12 "Wheel 1" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| info | UNMAPPED | OEM | 45 optional OEM pins are not mapped: OEM-A33-16 Neutral switch (NSW); OEM-A33-17 Starter signal (STSW2); OEM-A33-27 Ignition switch sense (IGSW, IG2 relay); OEM-A33-28 Shield ground (SLE2); OEM-A33-3 Stop light switch (ST1-); OEM-A33-7 Stop light switch (STP); OEM-A33-8 A/C pressure sensor (ACP); OEM-A34-11 DI injector confirmation (IJF1); OEM-A34-13 High-pressure fuel pump spill valve (FPF); OEM-A34-15 VVT cam sensor intake bank 2 (VV2+); OEM-A34-17 Knock sensor 2 (KNK2); OEM-A34-18 A/F ratio sensor (A1A-); OEM-A34-19 A/F ratio sensor (A1A+); OEM-A34-21 Heated oxygen sensor (OX1B, rear); OEM-A34-25 VVT cam sensor exhaust bank 2 (EV2+); OEM-A34-26 VVT cam sensor intake bank 1 (VV1+); OEM-A34-28 Knock sensor 1 (KNK1); OEM-A34-29 Shield ground (EKNK); OEM-A34-30 Shield ground (SLE1); OEM-A34-31 DI injector confirmation (IJF2); OEM-A34-32 High-pressure fuel pump spill valve (FPD); OEM-A34-35 Shield ground (SLE3); OEM-A34-9 Fuel pressure sensor (PR); OEM-A35-1 Canister vent valve (VPMP); OEM-A35-10 Fuel pump control monitor (DI); OEM-A35-15 Tachometer output (TACH); OEM-A35-17 ETCS relay (MCR); OEM-A35-19 Fuel pump control (FPC); OEM-A35-20 Canister pressure sensor (PPMP); OEM-A35-26 Starter signal (STA); OEM-A35-35 A/C clutch relay (AC); OEM-A35-5 Injector relay (IREL); OEM-A35-7 ETCS relay (+BM); OEM-A35-8 Leak detection pump (MPMP); OEM-A36-11 Purge valve (PRG); OEM-A36-14 Injector 1 direct (#1); OEM-A36-16 OCV intake bank 2 (OC2); OEM-A36-17 OCV intake bank 1 (OC1); OEM-A36-20 Oil temperature (OT); OEM-A36-23 Injector 4 direct (#4); OEM-A36-24 Injector 3 direct (#3); OEM-A36-25 Injector 2 direct (#2); OEM-A36-5 OCV exhaust bank 2 (OE2); OEM-A36-6 Heated oxygen sensor heater (HT1B); OEM-A36-7 OCV exhaust bank 1 (OE1) |
Accepted (0)
| Code | Subject | Reason | By |
|---|
Notes
Fit check: needs add-on. Resolve these before building: - No drive-by-wire; needs a cable-throttle conversion or an external DBW controller - No knock input; the stock knock sensor would be unused Auto-mapped by auto_map() from the library pin data on 2026-10-11. Review every wire against both manuals before building. Open items: - OEM-A36 31: Ignition coil 3 (IGT3): no free ignition output on DTAFast T2i - OEM-A36 8: Ignition coil 4 (IGT4): no free ignition output on DTAFast T2i - OEM-A36 12: Injector 1 port (#10): no free injector output on DTAFast T2i - OEM-A36 22: Injector 2 port (#20): no free injector output on DTAFast T2i - OEM-A36 32: Injector 3 port (#30): no free injector output on DTAFast T2i - OEM-A36 13: Injector 4 port (#40): no free injector output on DTAFast T2i - OEM-A36 1: Throttle actuator motor - (M-): no free hbridge on DTAFast T2i - OEM-A36 2: Throttle actuator motor + (M+): no free hbridge on DTAFast T2i Not wired: - OEM-A34 26: VVT cam sensor intake bank 1 (VV1+): no free cam_hall/cam_vr/frequency_in input on DTAFast T2i - OEM-A34 25: VVT cam sensor exhaust bank 2 (EV2+): no free cam_hall/cam_vr/frequency_in input on DTAFast T2i - OEM-A34 15: VVT cam sensor intake bank 2 (VV2+): no free cam_hall/cam_vr/frequency_in input on DTAFast T2i - OEM-A34 28: Knock sensor 1 (KNK1): no free knock input on DTAFast T2i - OEM-A34 17: Knock sensor 2 (KNK2): no free knock input on DTAFast T2i - OEM-A36 14: Injector 1 direct (#1): no free injector output on DTAFast T2i - OEM-A36 25: Injector 2 direct (#2): no free injector output on DTAFast T2i - OEM-A36 24: Injector 3 direct (#3): no free injector output on DTAFast T2i - OEM-A36 23: Injector 4 direct (#4): no free injector output on DTAFast T2i - OEM-A33 28: Shield ground (SLE2): no shield pin on DTAFast T2i - OEM-A34 29: Shield ground (EKNK): no shield pin on DTAFast T2i - OEM-A34 30: Shield ground (SLE1): no shield pin on DTAFast T2i - OEM-A34 35: Shield ground (SLE3): no shield pin on DTAFast T2i - OEM-A33 27: Ignition switch sense (IGSW, IG2 relay): key-on 12 V sense — optional in a swap (the main relay is energized from keyed 12 V, not from this pin); DTAFast T2i has no dedicated key-on input - OEM-A35 17: ETCS relay (MCR): no free relay_control/low_side/ls_hs/injector/hbridge rated ≥ 0.2 A on DTAFast T2i - OEM-A35 35: A/C clutch relay (AC): no free relay_control/low_side/ls_hs/injector/hbridge rated ≥ 0.2 A on DTAFast T2i - OEM-A35 5: Injector relay (IREL): no free relay_control/low_side/ls_hs/injector/hbridge rated ≥ 0.2 A on DTAFast T2i - OEM-A35 7: ETCS relay (+BM): no free relay_control/low_side/ls_hs/injector/hbridge rated ≥ 0.2 A on DTAFast T2i - OEM-A36 6: Heated oxygen sensor heater (HT1B): no free heater_low_side/low_side/ls_hs/hbridge on DTAFast T2i - OEM-A36 17: OCV intake bank 1 (OC1): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A36 7: OCV exhaust bank 1 (OE1): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A36 16: OCV intake bank 2 (OC2): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A36 5: OCV exhaust bank 2 (OE2): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A34 13: High-pressure fuel pump spill valve (FPF): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A34 32: High-pressure fuel pump spill valve (FPD): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A35 1: Canister vent valve (VPMP): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A35 19: Fuel pump control (FPC): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A35 8: Leak detection pump (MPMP): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A36 11: Purge valve (PRG): no free low_side/ls_hs/injector/hbridge on DTAFast T2i - OEM-A35 15: Tachometer output (TACH): no free tacho/frequency_out/low_side/ls_hs on DTAFast T2i - OEM-A34 21: Heated oxygen sensor (OX1B, rear): no free o2_narrowband/analog_0_5 on DTAFast T2i - OEM-A36 20: Oil temperature (OT): no free thermistor/analog_0_5 on DTAFast T2i - OEM-A33 8: A/C pressure sensor (ACP): no free analog_0_5 on DTAFast T2i - OEM-A34 11: DI injector confirmation (IJF1): no free analog_0_5 on DTAFast T2i - OEM-A34 31: DI injector confirmation (IJF2): no free analog_0_5 on DTAFast T2i - OEM-A34 9: Fuel pressure sensor (PR): no free analog_0_5 on DTAFast T2i - OEM-A35 10: Fuel pump control monitor (DI): no free analog_0_5 on DTAFast T2i - OEM-A35 20: Canister pressure sensor (PPMP): no free analog_0_5 on DTAFast T2i - OEM-A33 16: Neutral switch (NSW): no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-A33 17: Starter signal (STSW2): no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-A33 3: Stop light switch (ST1-): no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-A33 7: Stop light switch (STP): no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-A35 26: Starter signal (STA): no free switch_in/frequency_in/analog_0_5 on DTAFast T2i - OEM-A34 18: A/F ratio sensor (A1A-): not classified in the library; wire by hand - OEM-A34 19: A/F ratio sensor (A1A+): not classified in the library; wire by hand
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | DTAFast T2i ECU wiring diagram | https://cdn.shopify.com/s/files/1/0848/7508/4108/files/T2i_Wiring-Diagram.pdf?v=1728571341 | — | — | — |
| 4 | vendor_doc | Scion FR-S / Toyota 86 Repair Manual (2013) — FA20 ECM terminal pinout (SFI system) | https://gt86.me/images/0/09/2013_Scion_FR-S_Repair_Manual.pdf | — | — | — |