MX-5 Miata Mazdaspeed 2004-05 (BP-ZET turbo, no VVT) → Speeduino Speeduino v0.4 (auto)
MX-5 Miata Mazdaspeed 2004-05 (BP-ZET turbo, no VVT) — Speeduino — Speeduino
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-11
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 2: read the Findings page before cutting any wire |
| Size of the job | 4 wires · 2 connectors · 0 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-4-D | SPEEDUINO-A-31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-4-E | SPEEDUINO-A-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | OEM-4-AE | SPEEDUINO-A-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-4-R | SPEEDUINO-A-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| No supply/ground nets found to cross-check. | |||||
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
OEM-4
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| AC | Data link connector (DLC TEN, turbo) | — | — | — | — | — | — | — | — |
| AE | BARO/MAP sensor (turbo boost pressure) | — | W3 | — | 0.5 | SPEEDUINO-A-11 | — | — | — |
| D | Boost control solenoid (turbo) | — | W1 | — | 0.5 | SPEEDUINO-A-31 | — | — | — |
| E | Boost control solenoid (turbo) | — | W2 | — | 0.5 | SPEEDUINO-A-32 | — | — | — |
| R | Intake air temperature 2 (IAT2, turbo) | — | W4 | — | 0.5 | SPEEDUINO-A-19 | — | — | — |
SPEEDUINO-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector 1 | — | — | — | — | — | — | — | — |
| 10 | Ground | — | — | — | — | — | — | — | — |
| 11 | MAP sensor (0-5V) | — | W3 | — | 0.5 | OEM-4-AE | — | — | — |
| 12 | Ground | — | — | — | — | — | — | — | — |
| 13 | 5V | — | — | — | — | — | — | — | — |
| 14 | Proto area 1 (flex fuel) | — | — | — | — | — | — | — | — |
| 15 | Proto area 2 (fan) | — | — | — | — | — | — | — | — |
| 16 | Proto area 3 (fuel pump) | — | — | — | — | — | — | — | — |
| 17 | Proto area 4 (tachometer) | — | — | — | — | — | — | — | — |
| 18 | Proto area 5 (clutch) | — | — | — | — | — | — | — | — |
| 19 | Coolant temp (CLT) | — | W4 | — | 0.5 | OEM-4-R | — | — | — |
| 2 | Injector 2 | — | — | — | — | — | — | — | — |
| 20 | Inlet air temp (IAT) | — | — | — | — | — | — | — | — |
| 21 | O2 sensor | — | — | — | — | — | — | — | — |
| 22 | TPS input | — | — | — | — | — | — | — | — |
| 23 | Ground | — | — | — | — | — | — | — | — |
| 24 | Cam input / VR2+ | — | — | — | — | — | — | — | — |
| 25 | Crank input / VR1+ | — | — | — | — | — | — | — | — |
| 26 | VR2- | — | — | — | — | — | — | — | — |
| 27 | VR1- | — | — | — | — | — | — | — | — |
| 28 | 5V | — | — | — | — | — | — | — | — |
| 29 | Idle stepper 2B | — | — | — | — | — | — | — | — |
| 3 | Injector 3 | — | — | — | — | — | — | — | — |
| 30 | Idle stepper 2A | — | — | — | — | — | — | — | — |
| 31 | Idle stepper 1A | — | W1 | — | 0.5 | OEM-4-D | — | — | — |
| 32 | Idle stepper 1B | — | W2 | — | 0.5 | OEM-4-E | — | — | — |
| 33 | Ignition 3 | — | — | — | — | — | — | — | — |
| 34 | Ignition 2 | — | — | — | — | — | — | — | — |
| 35 | Boost | — | — | — | — | — | — | — | — |
| 36 | Idle 2 (3-wire idle) | — | — | — | — | — | — | — | — |
| 37 | PWM idle | — | — | — | — | — | — | — | — |
| 38 | VVT | — | — | — | — | — | — | — | — |
| 5 | Injector 4 | — | — | — | — | — | — | — | — |
| 7 | Ignition 1 | — | — | — | — | — | — | — | — |
| 8 | Ignition 4 | — | — | — | — | — | — | — | — |
| 9 | Ground | — | — | — | — | — | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-4-AC | Data link connector (DLC TEN, turbo) | serial | — | — | — | BrY | single_source |
| OEM-4-AE | BARO/MAP sensor (turbo boost pressure) | analog_in | SPEEDUINO-A-11 | MAP sensor (0-5V) | analog_in | LY | single_source |
| OEM-4-D | Boost control solenoid (turbo) | high_side_out | SPEEDUINO-A-31 | Idle stepper 1A | hbridge_out | Y | single_source |
| OEM-4-E | Boost control solenoid (turbo) | high_side_out | SPEEDUINO-A-32 | Idle stepper 1B | hbridge_out | Y | single_source |
| OEM-4-R | Intake air temperature 2 (IAT2, turbo) | temp_in | SPEEDUINO-A-19 | Coolant temp (CLT) | temp_in | VY | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-4-D | SPEEDUINO-A-31 | 0.5 | no route | Boost control solenoid (turbo) | — | |
| W2 | OEM-4-E | SPEEDUINO-A-32 | 0.5 | no route | Boost control solenoid (turbo) | — | |
| W3 | OEM-4-AE | SPEEDUINO-A-11 | 0.5 | no route | BARO/MAP sensor (turbo boost pressure) | — | |
| W4 | OEM-4-R | SPEEDUINO-A-19 | 0.5 | no route | Intake air temperature 2 (IAT2, turbo) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (5)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | PHYS_REQUIRED_OPEN | SPEEDUINO-A-10 | SPEEDUINO-A-10 "Ground" is required but not wired. |
| error | PHYS_REQUIRED_OPEN | SPEEDUINO-A-9 | SPEEDUINO-A-9 "Ground" is required but not wired. |
| warn | NET_FAMILY | OEM-4-D ↔ SPEEDUINO-A-31 | OEM-4-D "Boost control solenoid (turbo)" [high_side_out] is wired to SPEEDUINO-A-31 "Idle stepper 1A" [hbridge_out]. A half-bridge can act as a high-side switch only if configured that way. |
| warn | NET_FAMILY | OEM-4-E ↔ SPEEDUINO-A-32 | OEM-4-E "Boost control solenoid (turbo)" [high_side_out] is wired to SPEEDUINO-A-32 "Idle stepper 1B" [hbridge_out]. A half-bridge can act as a high-side switch only if configured that way. |
| info | UNMAPPED | OEM | 1 optional OEM pins are not mapped: OEM-4-AC Data link connector (DLC TEN, turbo) |
Accepted (0)
| Code | Subject | Reason | By |
|---|
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-11. Review every wire against both manuals before building. Open items: - Main-relay feed: no ecu_main_power pin on the stock or the new ECU - SPEEDUINO-A 10: Ground: required by Speeduino Speeduino but no stock pin feeds it; wire by hand - SPEEDUINO-A 9: Ground: required by Speeduino Speeduino but no stock pin feeds it; wire by hand Not wired: - OEM-4 AC: Data link connector (DLC TEN, turbo): no free k_line on Speeduino Speeduino
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | oem_manual | 2005 Mazda MX-5 Miata Engine Performance Control System (PCM terminal voltage reference, BP and BP WITH TC) | https://trull.org/alex/pubmirror/www.mellens.net/mazda/Mazda-Miata-2005/engine_control_system.pdf | — | — | — |
| 4 | vendor_doc | Adaptronic eSel039 Select Plugin ECU for Mazda MX5 / Miata NB8B/C (OEM ECU pinout) | https://www.miataturbo.net/attachments/ecus-tuning-54/04-msm-ecu-pinout-104032/nb8bc_oem_ecu_pinouts-224948d1602912806 | — | — | — |
| 4 | vendor_doc | Speeduino Manual (08/04/25) — V0.4 board IDC40 pinout & features | https://speeduino.com/Speeduino_manual.pdf | archive | 2026-10-05 | 21806bd29ef0 |