S2000 AP2 2006–09 cable conversion → MaxxECU MaxxECU MINI
AP2 2006–09 converted to cable throttle — MaxxECU — MaxxECU MINI
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-11
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 1: read the Findings page before cutting any wire |
| Size of the job | 42 wires · 12 connectors · 5 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-A-2 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-A-3 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | MAXXECUMINI-C1-H4 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-A-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-A-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-A-8 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-A-9 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-E-3 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | MAXXECUMINI-C1-G4 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-A-24 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | SP-0V-1 | MAXXECUMINI-C1-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | SP-0V-1 | MAXXECUMINI-C1-B3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | SP-0V-1 | MAXXECUMINI-C1-B4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | SP-0V-1 | MAXXECUMINI-C1-D4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | SP-5V1-1 | MAXXECUMINI-C1-E2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-A-7 | MAXXECUMINI-C1-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-A-16 | MAXXECUMINI-C1-F1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-A-15 | MAXXECUMINI-C1-F2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-A-14 | MAXXECUMINI-C1-F3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-A-13 | MAXXECUMINI-C1-F4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-B-5 | MAXXECUMINI-C1-G3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-B-4 | MAXXECUMINI-C1-H1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-B-3 | MAXXECUMINI-C1-H2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-B-2 | MAXXECUMINI-C1-H3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-E-17 | MAXXECUMINI-C1-G2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-E-7 | MAXXECUMINI-C1-G1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-B-6 | RLY1-R-OUT | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | SP-14V-1 | RLY1-R-IN | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | SP-14V-1 | RLY1-R-COIL+ | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | RLY1-R-COIL- | MAXXECUMINI-C1-E1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-A-30 | MAXXECUMINI-C1-C3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-B-8 | MAXXECUMINI-C1-C1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-E-1 | MAXXECUMINI-C1-C2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-A-18 | MAXXECUMINI-C1-B1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-B-11 | MAXXECUMINI-C1-B2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-E-11 | MAXXECUMINI-C1-E4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-E-24 | MAXXECUMINI-C1-E3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-A-21 | SP-5V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | SP-5V-1 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | SP-5V-1 | TPS-J-VCC | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | TPS-J-SIG | MAXXECUMINI-C1-C4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | TPS-J-GND | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | MAXXECUMINI-C1-E2 | MAXXECUMINI-C1-A2 | open (OL) | 5 V sensor reference must not touch sensor ground | |
| 2 | MAXXECUMINI-C1-H4 | MAXXECUMINI-C1-A2 | open (OL) | +12 V supply must not touch sensor ground | |
| 3 | MAXXECUMINI-C1-H4 | MAXXECUMINI-C1-G4 | open (OL) | +12 V supply must not touch power ground | |
| 4 | MAXXECUMINI-C1-A2 | RLY1-R-OUT | open (OL) | sensor ground must not touch +12 V supply | |
| 5 | MAXXECUMINI-C1-E2 | RLY1-R-OUT | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 6 | MAXXECUMINI-C1-G4 | MAXXECUMINI-C1-E2 | open (OL) | power ground must not touch 5 V sensor reference | |
| 7 | MAXXECUMINI-C1-G4 | RLY1-R-OUT | open (OL) | power ground must not touch +12 V supply | |
| 8 | MAXXECUMINI-C1-H4 | MAXXECUMINI-C1-E2 | open (OL) | +12 V supply must not touch 5 V sensor reference |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
MAXXECUMINI-C1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A1 | TRIGGER | — | W16 | — | 0.5 | OEM-A-7 | — | — | — |
| A2 | TRIGGER GND | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| B1 | DIN 1 (Hall only) | — | W34 | — | 0.5 | OEM-A-18 | — | — | — |
| B2 | DIN 2 (Hall only) | — | W35 | — | 0.5 | OEM-B-11 | — | — | — |
| B3 | SENSOR GND | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| B4 | SENSOR GND | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| C1 | CLT | — | W32 | — | 0.5 | OEM-B-8 | — | — | — |
| C2 | IAT | — | W33 | — | 0.5 | OEM-E-1 | — | — | — |
| C3 | AIN 3 (0-5V) | — | W31 | — | 0.5 | OEM-A-30 | — | — | — |
| C4 | AIN 4 (0-5V) | — | W41 | — | 0.5 | TPS-J-SIG | — | — | — |
| D1 | GPO 8/TACHO | — | — | — | — | — | — | — | — |
| D2 | TPS | — | — | — | — | — | — | — | — |
| D3 | GND Shield | — | — | — | — | — | — | — | — |
| D4 | SENSOR GND | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| E1 | GPO 3 | — | W30 | — | 0.5 | RLY1-R-COIL- | — | — | — |
| E2 | +5V sensor supply | — | W15 | — | 0.5 | SP-5V1-1 | — | — | — |
| E3 | CAN L | — | W37 | — | 0.5 | OEM-E-24 | — | — | — |
| E4 | CAN H | — | W36 | — | 0.5 | OEM-E-11 | — | — | — |
| F1 | IGN 1 | — | W17 | — | 0.5 | OEM-A-16 | — | — | — |
| F2 | IGN 2 | — | W18 | — | 0.5 | OEM-A-15 | — | — | — |
| F3 | IGN 3 | — | W19 | — | 0.5 | OEM-A-14 | — | — | — |
| F4 | IGN 4 | — | W20 | — | 0.5 | OEM-A-13 | — | — | — |
| G1 | GPO 2 | — | W26 | — | 0.5 | OEM-E-7 | — | — | — |
| G2 | GPO 1 | — | W25 | — | 0.5 | OEM-E-17 | — | — | — |
| G3 | INJ 1 | — | W21 | — | 0.5 | OEM-B-5 | — | — | — |
| G4 | ENGINE GND | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| H1 | INJ 2 | — | W22 | — | 0.5 | OEM-B-4 | — | — | — |
| H2 | INJ 3 | — | W23 | — | 0.5 | OEM-B-3 | — | — | — |
| H3 | INJ 4 | — | W24 | — | 0.5 | OEM-B-2 | — | — | — |
| H4 | +12V (ECU power supply) | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
OEM-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Knock sensor | — | — | — | — | — | — | — | — |
| 2 | Ignition power 2 | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 3 | Ignition power 1 | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 4 | Power ground 2 | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | Power ground 1 | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Cam position sensor (T2) | — | — | — | — | — | — | — | — |
| 7 | Crank position sensor (T1) | — | W16 | — | 0.5 | MAXXECUMINI-C1-A1 | — | — | — |
| 8 | Logic ground 2 | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 9 | Logic ground 1 | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 10 | A/F sensor heater | — | — | — | — | — | — | — | — |
| 11 | Unused cavity | — | — | — | — | — | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Ignition coil 4 | — | W20 | — | 0.5 | MAXXECUMINI-C1-F4 | — | — | — |
| 14 | Ignition coil 3 | — | W19 | — | 0.5 | MAXXECUMINI-C1-F3 | — | — | — |
| 15 | Ignition coil 2 | — | W18 | — | 0.5 | MAXXECUMINI-C1-F2 | — | — | — |
| 16 | Ignition coil 1 | — | W17 | — | 0.5 | MAXXECUMINI-C1-F1 | — | — | — |
| 17 | Unused cavity | — | — | — | — | — | — | — | — |
| 18 | Vehicle speed sensor | — | W34 | — | 0.5 | MAXXECUMINI-C1-B1 | — | — | — |
| 19 | Unused cavity | — | — | — | — | — | — | — | — |
| 20 | Sensor voltage 2 | — | — | — | — | — | — | — | — |
| 21 | Sensor voltage 1 | — | W38 | — | 0.5 | SP-5V-1 | — | — | — |
| 22 | Unused cavity | — | — | — | — | — | — | — | — |
| 23 | Sensor ground 2 | — | — | — | — | — | — | — | — |
| 24 | Sensor ground 1 | — | W10 | — | 0.5 | SP-0V-1 | — | — | — |
| 25 | Accelerator pedal position B | — | — | — | — | — | — | — | — |
| 26 | Accelerator pedal position A | — | — | — | — | — | — | — | — |
| 27 | Unused cavity | — | — | — | — | — | — | — | — |
| 28 | A/F sensor signal − | — | — | — | — | — | — | — | — |
| 29 | Unused cavity | — | — | — | — | — | — | — | — |
| 30 | MAP sensor | — | W31 | — | 0.5 | MAXXECUMINI-C1-C3 | — | — | — |
| 31 | A/F sensor signal + | — | — | — | — | — | — | — | — |
OEM-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Unused cavity | — | — | — | — | — | — | — | — |
| 2 | Injector 4 | — | W24 | — | 0.5 | MAXXECUMINI-C1-H3 | — | — | — |
| 3 | Injector 3 | — | W23 | — | 0.5 | MAXXECUMINI-C1-H2 | — | — | — |
| 4 | Injector 2 | — | W22 | — | 0.5 | MAXXECUMINI-C1-H1 | — | — | — |
| 5 | Injector 1 | — | W21 | — | 0.5 | MAXXECUMINI-C1-G3 | — | — | — |
| 6 | VTEC solenoid | — | W27 | — | 0.5 | RLY1-R-OUT | — | — | — |
| 7 | Unused cavity | — | — | — | — | — | — | — | — |
| 8 | Coolant temp sensor | — | W32 | — | 0.5 | MAXXECUMINI-C1-C1 | — | — | — |
| 9 | Unused cavity | — | — | — | — | — | — | — | — |
| 10 | Alternator L signal | — | — | — | — | — | — | — | — |
| 11 | VTEC oil pressure switch | — | W35 | — | 0.5 | MAXXECUMINI-C1-B2 | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Alternator FR signal | — | — | — | — | — | — | — | — |
| 14 | Unused cavity | — | — | — | — | — | — | — | — |
| 15 | Engine mount control solenoid | — | — | — | — | — | — | — | — |
| 16 | Unused cavity | — | — | — | — | — | — | — | — |
| 17 | Intake air temp sensor | — | — | — | — | — | — | — | — |
| 18 | Alternator control | — | — | — | — | — | — | — | — |
| 19 | Throttle actuator command to throttle control module (SEFD) | — | — | — | — | — | — | — | — |
| 20 | Throttle actuator command to throttle control module (SEDF) | — | — | — | — | — | — | — | — |
| 21 | Evap canister purge valve | — | — | — | — | — | — | — | — |
| 22 | Unused cavity | — | — | — | — | — | — | — | — |
| 23 | Unused cavity | — | — | — | — | — | — | — | — |
| 24 | Unused cavity | — | — | — | — | — | — | — | — |
OEM-D
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Cruise set switch | — | — | — | — | — | — | — | — |
| 2 | Unused cavity | — | — | — | — | — | — | — | — |
| 3 | Unused cavity | — | — | — | — | — | — | — | — |
| 4 | Cruise main switch | — | — | — | — | — | — | — | — |
| 5 | Unused cavity | — | — | — | — | — | — | — | — |
| 6 | Unused cavity | — | — | — | — | — | — | — | — |
| 7 | Cruise resume switch | — | — | — | — | — | — | — | — |
| 8 | Brake pedal position switch | — | — | — | — | — | — | — | — |
| 9 | Cruise clutch signal | — | — | — | — | — | — | — | — |
| 10 | Unused cavity | — | — | — | — | — | — | — | — |
| 11 | Unused cavity | — | — | — | — | — | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Unused cavity | — | — | — | — | — | — | — | — |
| 14 | Unused cavity | — | — | — | — | — | — | — | — |
| 15 | Throttle actuator relay | — | — | — | — | — | — | — | — |
| 16 | Unused cavity | — | — | — | — | — | — | — | — |
| 17 | Unused cavity | — | — | — | — | — | — | — | — |
OEM-E
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Coolant temp sensor 2 | — | W33 | — | 0.5 | MAXXECUMINI-C1-C2 | — | — | — |
| 2 | Unused cavity | — | — | — | — | — | — | — | — |
| 3 | Logic ground 3 | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 4 | Sensor ground 3 | — | — | — | — | — | — | — | — |
| 5 | Sensor voltage 3 | — | — | — | — | — | — | — | — |
| 6 | Unused cavity | — | — | — | — | — | — | — | — |
| 7 | Main relay control | — | W26 | — | 0.5 | MAXXECUMINI-C1-G1 | — | — | — |
| 8 | A/F sensor heater relay | — | — | — | — | — | — | — | — |
| 9 | Ignition signal | — | — | — | — | — | — | — | — |
| 10 | Unused cavity | — | — | — | — | — | — | — | — |
| 11 | CAN H | — | W36 | — | 0.5 | MAXXECUMINI-C1-E4 | — | — | — |
| 12 | Radiator fan control | — | — | — | — | — | — | — | — |
| 13 | Multiplex communication | — | — | — | — | — | — | — | — |
| 14 | Fuel tank pressure sensor | — | — | — | — | — | — | — | — |
| 15 | Electrical load detector | — | — | — | — | — | — | — | — |
| 16 | Power steering load detector | — | — | — | — | — | — | — | — |
| 17 | Fuel pump relay | — | W25 | — | 0.5 | MAXXECUMINI-C1-G2 | — | — | — |
| 18 | A/C clutch relay | — | — | — | — | — | — | — | — |
| 19 | Evap canister vent shut valve | — | — | — | — | — | — | — | — |
| 20 | Secondary O2 sensor | — | — | — | — | — | — | — | — |
| 21 | Secondary O2 heater | — | — | — | — | — | — | — | — |
| 22 | Brake pedal switch | — | — | — | — | — | — | — | — |
| 23 | Unused cavity | — | — | — | — | — | — | — | — |
| 24 | CAN L | — | W37 | — | 0.5 | MAXXECUMINI-C1-E3 | — | — | — |
| 25 | Engine speed pulse (tacho) | — | — | — | — | — | — | — | — |
| 26 | Vehicle speed output | — | — | — | — | — | — | — | — |
| 27 | Immobilizer code | — | — | — | — | — | — | — | — |
| 28 | A/C switch signal | — | — | — | — | — | — | — | — |
| 29 | Service check signal | — | — | — | — | — | — | — | — |
| 30 | Write enable signal | — | — | — | — | — | — | — | — |
| 31 | Unused cavity | — | — | — | — | — | — | — | — |
RLY1-R
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| COIL+ | Relay coil positive (switched +12 V) | — | W29 | — | 0.5 | SP-14V-1 | — | — | — |
| COIL- | Relay coil negative (ECU low-side driver) | — | W30 | — | 0.5 | MAXXECUMINI-C1-E1 | — | — | — |
| IN | Relay contact input (switched +12 V) | — | W28 | — | 0.5 | SP-14V-1 | — | — | — |
| OUT | Relay contact output (switched +12 V to load) | — | W27 | — | 0.5 | OEM-B-6 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W42 | — | 0.5 | TPS-J-GND | — | — | — |
| 1 | — | — | W10 | — | 0.5 | OEM-A-24 | — | — | — |
| 1 | — | — | W11 | — | 0.5 | MAXXECUMINI-C1-A2 | — | — | — |
| 1 | — | — | W12 | — | 0.5 | MAXXECUMINI-C1-B3 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | MAXXECUMINI-C1-B4 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | MAXXECUMINI-C1-D4 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W2 | — | 0.85 | OEM-A-3 | — | — | — |
| 1 | — | — | W1 | — | 0.85 | OEM-A-2 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | MAXXECUMINI-C1-H4 | — | — | — |
| 1 | — | — | W28 | — | 0.5 | RLY1-R-IN | — | — | — |
| 1 | — | — | W29 | — | 0.5 | RLY1-R-COIL+ | — | — | — |
SP-5V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W38 | — | 0.5 | OEM-A-21 | — | — | — |
| 1 | — | — | W39 | — | 0.5 | SP-5V1-1 | — | — | — |
| 1 | — | — | W40 | — | 0.5 | TPS-J-VCC | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W39 | — | 0.5 | SP-5V-1 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | MAXXECUMINI-C1-E2 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W4 | — | 0.85 | OEM-A-4 | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-A-5 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-A-8 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-A-9 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | OEM-E-3 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | MAXXECUMINI-C1-G4 | — | — | — |
TPS-J
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| VCC | 5V supply in | — | W40 | — | 0.5 | SP-5V-1 | — | — | — |
| SIG | Throttle position signal | — | W41 | — | 0.5 | MAXXECUMINI-C1-C4 | — | — | — |
| GND | Sensor ground | — | W42 | — | 0.5 | SP-0V-1 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-A-1 | Knock sensor | knock_in | — | — | — | single_source | |
| OEM-A-10 | A/F sensor heater | low_side_out | — | — | — | single_source | |
| OEM-A-11 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-12 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-13 | Ignition coil 4 | ignition_out | MAXXECUMINI-C1-F4 | IGN 4 | ignition_out | single_source | |
| OEM-A-14 | Ignition coil 3 | ignition_out | MAXXECUMINI-C1-F3 | IGN 3 | ignition_out | single_source | |
| OEM-A-15 | Ignition coil 2 | ignition_out | MAXXECUMINI-C1-F2 | IGN 2 | ignition_out | single_source | |
| OEM-A-16 | Ignition coil 1 | ignition_out | MAXXECUMINI-C1-F1 | IGN 1 | ignition_out | single_source | |
| OEM-A-17 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-18 | Vehicle speed sensor | digital_in | MAXXECUMINI-C1-B1 | DIN 1 (Hall only) | digital_in | single_source | |
| OEM-A-19 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-2 | Ignition power 2 | power_in | MAXXECUMINI-C1-H4 + RLY1-R-COIL+ + RLY1-R-IN | +12V (ECU power supply) + Relay coil positive (switched +12 V) + Relay contact input (switched +12 V) | power_in + power_out | single_source | |
| OEM-A-20 | Sensor voltage 2 | vref | — | — | — | corroborated | |
| OEM-A-21 | Sensor voltage 1 | vref | MAXXECUMINI-C1-E2 + TPS-J-VCC | +5V sensor supply + 5V supply in | power_in + vref | single_source | |
| OEM-A-22 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-23 | Sensor ground 2 | sensor_ground | — | — | — | corroborated | |
| OEM-A-24 | Sensor ground 1 | sensor_ground | MAXXECUMINI-C1-A2 + MAXXECUMINI-C1-B3 + MAXXECUMINI-C1-B4 + MAXXECUMINI-C1-D4 + TPS-J-GND | TRIGGER GND + SENSOR GND + SENSOR GND + SENSOR GND + Sensor ground | sensor_ground | single_source | |
| OEM-A-25 | Accelerator pedal position B | analog_in | — | — | — | corroborated | |
| OEM-A-26 | Accelerator pedal position A | analog_in | — | — | — | corroborated | |
| OEM-A-27 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-28 | A/F sensor signal − | — | — | — | — | single_source | |
| OEM-A-29 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-3 | Ignition power 1 | power_in | MAXXECUMINI-C1-H4 + RLY1-R-COIL+ + RLY1-R-IN | +12V (ECU power supply) + Relay coil positive (switched +12 V) + Relay contact input (switched +12 V) | power_in + power_out | single_source | |
| OEM-A-30 | MAP sensor | analog_in | MAXXECUMINI-C1-C3 | AIN 3 (0-5V) | analog_in | single_source | |
| OEM-A-31 | A/F sensor signal + | — | — | — | — | single_source | |
| OEM-A-4 | Power ground 2 | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | single_source | |
| OEM-A-5 | Power ground 1 | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | single_source | |
| OEM-A-6 | Cam position sensor (T2) | trigger_in | — | — | — | single_source | |
| OEM-A-7 | Crank position sensor (T1) | trigger_in | MAXXECUMINI-C1-A1 | TRIGGER | trigger_in | single_source | |
| OEM-A-8 | Logic ground 2 | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | single_source | |
| OEM-A-9 | Logic ground 1 | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | single_source | |
| OEM-B-1 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-10 | Alternator L signal | — | — | — | — | single_source | |
| OEM-B-11 | VTEC oil pressure switch | digital_in | MAXXECUMINI-C1-B2 | DIN 2 (Hall only) | digital_in | single_source | |
| OEM-B-12 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-13 | Alternator FR signal | analog_in | — | — | — | single_source | |
| OEM-B-14 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-15 | Engine mount control solenoid | low_side_out | — | — | — | single_source | |
| OEM-B-16 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-17 | Intake air temp sensor | temp_in | — | — | — | single_source | |
| OEM-B-18 | Alternator control | low_side_out | — | — | — | single_source | |
| OEM-B-19 | Throttle actuator command to throttle control module (SEFD) | — | — | — | — | conflict | |
| OEM-B-2 | Injector 4 | injector_out | MAXXECUMINI-C1-H3 | INJ 4 | injector_out | single_source | |
| OEM-B-20 | Throttle actuator command to throttle control module (SEDF) | — | — | — | — | conflict | |
| OEM-B-21 | Evap canister purge valve | low_side_out | — | — | — | single_source | |
| OEM-B-22 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-23 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-24 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-3 | Injector 3 | injector_out | MAXXECUMINI-C1-H2 | INJ 3 | injector_out | single_source | |
| OEM-B-4 | Injector 2 | injector_out | MAXXECUMINI-C1-H1 | INJ 2 | injector_out | single_source | |
| OEM-B-5 | Injector 1 | injector_out | MAXXECUMINI-C1-G3 | INJ 1 | injector_out | single_source | |
| OEM-B-6 | VTEC solenoid | high_side_out | RLY1-R-OUT | Relay contact output (switched +12 V to load) | power_out | single_source | |
| OEM-B-7 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-8 | Coolant temp sensor | temp_in | MAXXECUMINI-C1-C1 | CLT | temp_in | single_source | |
| OEM-B-9 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-1 | Cruise set switch | digital_in | — | — | — | single_source | |
| OEM-D-10 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-11 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-12 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-13 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-14 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-15 | Throttle actuator relay | low_side_out | — | — | — | single_source | |
| OEM-D-16 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-17 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-2 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-3 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-4 | Cruise main switch | digital_in | — | — | — | single_source | |
| OEM-D-5 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-6 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-7 | Cruise resume switch | digital_in | — | — | — | single_source | |
| OEM-D-8 | Brake pedal position switch | digital_in | — | — | — | single_source | |
| OEM-D-9 | Cruise clutch signal | digital_in | — | — | — | single_source | |
| OEM-E-1 | Coolant temp sensor 2 | temp_in | MAXXECUMINI-C1-C2 | IAT | temp_in | single_source | |
| OEM-E-10 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-11 | CAN H | can_h | MAXXECUMINI-C1-E4 | CAN H | can_h | single_source | |
| OEM-E-12 | Radiator fan control | low_side_out | — | — | — | single_source | |
| OEM-E-13 | Multiplex communication | serial | — | — | — | single_source | |
| OEM-E-14 | Fuel tank pressure sensor | analog_in | — | — | — | single_source | |
| OEM-E-15 | Electrical load detector | analog_in | — | — | — | single_source | |
| OEM-E-16 | Power steering load detector | analog_in | — | — | — | corroborated | |
| OEM-E-17 | Fuel pump relay | low_side_out | MAXXECUMINI-C1-G2 | GPO 1 | low_side_out | single_source | |
| OEM-E-18 | A/C clutch relay | low_side_out | — | — | — | single_source | |
| OEM-E-19 | Evap canister vent shut valve | low_side_out | — | — | — | single_source | |
| OEM-E-2 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-20 | Secondary O2 sensor | lambda_nb_in | — | — | — | single_source | |
| OEM-E-21 | Secondary O2 heater | low_side_out | — | — | — | single_source | |
| OEM-E-22 | Brake pedal switch | digital_in | — | — | — | single_source | |
| OEM-E-23 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-24 | CAN L | can_l | MAXXECUMINI-C1-E3 | CAN L | can_l | single_source | |
| OEM-E-25 | Engine speed pulse (tacho) | tacho_out | — | — | — | single_source | |
| OEM-E-26 | Vehicle speed output | tacho_out | — | — | — | single_source | |
| OEM-E-27 | Immobilizer code | — | — | — | — | single_source | |
| OEM-E-28 | A/C switch signal | digital_in | — | — | — | single_source | |
| OEM-E-29 | Service check signal | — | — | — | — | single_source | |
| OEM-E-3 | Logic ground 3 | ground | MAXXECUMINI-C1-G4 | ENGINE GND | ground | single_source | |
| OEM-E-30 | Write enable signal | — | — | — | — | single_source | |
| OEM-E-31 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-4 | Sensor ground 3 | sensor_ground | — | — | — | corroborated | |
| OEM-E-5 | Sensor voltage 3 | vref | — | — | — | corroborated | |
| OEM-E-6 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-7 | Main relay control | low_side_out | MAXXECUMINI-C1-G1 | GPO 2 | low_side_out | single_source | |
| OEM-E-8 | A/F sensor heater relay | low_side_out | — | — | — | single_source | |
| OEM-E-9 | Ignition signal | digital_in | — | — | — | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-A-2 | SP-14V-1 | 0.85 | no route | Ignition power 2 | — | |
| W2 | OEM-A-3 | SP-14V-1 | 0.85 | no route | Ignition power 1 | — | |
| W3 | SP-14V-1 | MAXXECUMINI-C1-H4 | 0.85 | no route | +12V (ECU power supply) | — | |
| W4 | OEM-A-4 | SP-GND-1 | 0.85 | no route | Power ground 2 | — | |
| W5 | OEM-A-5 | SP-GND-1 | 0.85 | no route | Power ground 1 | — | |
| W6 | OEM-A-8 | SP-GND-1 | 0.85 | no route | Logic ground 2 | — | |
| W7 | OEM-A-9 | SP-GND-1 | 0.85 | no route | Logic ground 1 | — | |
| W8 | OEM-E-3 | SP-GND-1 | 0.85 | no route | Logic ground 3 | — | |
| W9 | SP-GND-1 | MAXXECUMINI-C1-G4 | 0.85 | no route | ENGINE GND | — | |
| W10 | OEM-A-24 | SP-0V-1 | 0.5 | no route | Sensor ground 1 | — | |
| W11 | SP-0V-1 | MAXXECUMINI-C1-A2 | 0.5 | no route | TRIGGER GND | — | |
| W12 | SP-0V-1 | MAXXECUMINI-C1-B3 | 0.5 | no route | SENSOR GND | — | |
| W13 | SP-0V-1 | MAXXECUMINI-C1-B4 | 0.5 | no route | SENSOR GND | — | |
| W14 | SP-0V-1 | MAXXECUMINI-C1-D4 | 0.5 | no route | SENSOR GND | — | |
| W15 | SP-5V1-1 | MAXXECUMINI-C1-E2 | 0.5 | no route | +5V sensor supply | — | |
| W16 | OEM-A-7 | MAXXECUMINI-C1-A1 | 0.5 | no route | Crank position sensor (T1) | — | |
| W17 | OEM-A-16 | MAXXECUMINI-C1-F1 | 0.5 | no route | Ignition coil 1 | — | |
| W18 | OEM-A-15 | MAXXECUMINI-C1-F2 | 0.5 | no route | Ignition coil 2 | — | |
| W19 | OEM-A-14 | MAXXECUMINI-C1-F3 | 0.5 | no route | Ignition coil 3 | — | |
| W20 | OEM-A-13 | MAXXECUMINI-C1-F4 | 0.5 | no route | Ignition coil 4 | — | |
| W21 | OEM-B-5 | MAXXECUMINI-C1-G3 | 0.5 | no route | Injector 1 | — | |
| W22 | OEM-B-4 | MAXXECUMINI-C1-H1 | 0.5 | no route | Injector 2 | — | |
| W23 | OEM-B-3 | MAXXECUMINI-C1-H2 | 0.5 | no route | Injector 3 | — | |
| W24 | OEM-B-2 | MAXXECUMINI-C1-H3 | 0.5 | no route | Injector 4 | — | |
| W25 | OEM-E-17 | MAXXECUMINI-C1-G2 | 0.5 | no route | Fuel pump relay | — | |
| W26 | OEM-E-7 | MAXXECUMINI-C1-G1 | 0.5 | no route | Main relay control | — | |
| W27 | OEM-B-6 | RLY1-R-OUT | 0.5 | no route | VTEC solenoid | — | |
| W28 | SP-14V-1 | RLY1-R-IN | 0.5 | no route | Relay contact input (switched +12 V) | — | |
| W29 | SP-14V-1 | RLY1-R-COIL+ | 0.5 | no route | Relay coil positive (switched +12 V) | — | |
| W30 | RLY1-R-COIL- | MAXXECUMINI-C1-E1 | 0.5 | no route | Relay coil negative (ECU low-side driver) | — | |
| W31 | OEM-A-30 | MAXXECUMINI-C1-C3 | 0.5 | no route | MAP sensor | — | |
| W32 | OEM-B-8 | MAXXECUMINI-C1-C1 | 0.5 | no route | Coolant temp sensor | — | |
| W33 | OEM-E-1 | MAXXECUMINI-C1-C2 | 0.5 | no route | Coolant temp sensor 2 | — | |
| W34 | OEM-A-18 | MAXXECUMINI-C1-B1 | 0.5 | no route | Vehicle speed sensor | — | |
| W35 | OEM-B-11 | MAXXECUMINI-C1-B2 | 0.5 | no route | VTEC oil pressure switch | — | |
| W36 | OEM-E-11 | MAXXECUMINI-C1-E4 | 0.5 | no route | CAN H | — | |
| W37 | OEM-E-24 | MAXXECUMINI-C1-E3 | 0.5 | no route | CAN L | — | |
| W38 | OEM-A-21 | SP-5V-1 | 0.5 | no route | Sensor voltage 1 | — | |
| W39 | SP-5V-1 | SP-5V1-1 | 0.5 | no route | — | — | |
| W40 | SP-5V-1 | TPS-J-VCC | 0.5 | no route | 5V supply in | — | |
| W41 | TPS-J-SIG | MAXXECUMINI-C1-C4 | 0.5 | no route | Throttle position signal | — | |
| W42 | TPS-J-GND | SP-0V-1 | 0.5 | no route | Sensor ground | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | S2K-0609-ECU-A | Honda | S2000 2006–09 ECU plug A (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-B | Honda | S2000 2006–09 ECU plug B (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-D | Honda | S2000 2006–09 ECU plug D (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-E | Honda | S2000 2006–09 ECU plug E (P/N unknown) | 1.000 | ea |
| connector | TPS-3W | Generic | 3-way throttle position sensor plug (match to your throttle body) | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (8)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | REQUIRED_UNMAPPED | OEM-A-6 | Required OEM function "Cam position sensor (T2)" (trigger_in) is not connected to the new ECU. |
| warn | LOAD_UNKNOWN | MAXXECUMINI-C1-G1 | MAXXECUMINI-C1-G1 "GPO 2" drives OEM-E-7 Main relay control (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | MAXXECUMINI-C1-G2 | MAXXECUMINI-C1-G2 "GPO 1" drives OEM-E-17 Fuel pump relay (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | RLY1-R-OUT | RLY1-R-OUT "Relay contact output (switched +12 V to load)" drives OEM-B-6 VTEC solenoid (load 1.0 A) but its current rating is unknown. Check the ECU manual. |
| info | PIN_UNSOURCED | TPS-J-GND | TPS-J-GND "Sensor ground" has no recorded source. |
| info | PIN_UNSOURCED | TPS-J-SIG | TPS-J-SIG "Throttle position signal" has no recorded source. |
| info | PIN_UNSOURCED | TPS-J-VCC | TPS-J-VCC "5V supply in" has no recorded source. |
| info | UNMAPPED | OEM | 36 optional OEM pins are not mapped: OEM-A-1 Knock sensor; OEM-A-10 A/F sensor heater; OEM-A-28 A/F sensor signal −; OEM-A-31 A/F sensor signal +; OEM-B-10 Alternator L signal; OEM-B-13 Alternator FR signal; OEM-B-15 Engine mount control solenoid; OEM-B-17 Intake air temp sensor; OEM-B-18 Alternator control; OEM-B-19 Throttle actuator command to throttle control module (SEFD); OEM-B-20 Throttle actuator command to throttle control module (SEDF); OEM-B-21 Evap canister purge valve; OEM-D-1 Cruise set switch; OEM-D-15 Throttle actuator relay; OEM-D-4 Cruise main switch; OEM-D-7 Cruise resume switch; OEM-D-8 Brake pedal position switch; OEM-D-9 Cruise clutch signal; OEM-E-12 Radiator fan control; OEM-E-13 Multiplex communication; OEM-E-14 Fuel tank pressure sensor; OEM-E-15 Electrical load detector; OEM-E-16 Power steering load detector; OEM-E-18 A/C clutch relay; OEM-E-19 Evap canister vent shut valve; OEM-E-20 Secondary O2 sensor; OEM-E-21 Secondary O2 heater; OEM-E-22 Brake pedal switch; OEM-E-25 Engine speed pulse (tacho); OEM-E-26 Vehicle speed output; OEM-E-27 Immobilizer code; OEM-E-28 A/C switch signal; OEM-E-29 Service check signal; OEM-E-30 Write enable signal; OEM-E-8 A/F sensor heater relay; OEM-E-9 Ignition signal |
Accepted (6)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-A-20 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-A-23 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-A-25 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-A-26 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-E-4 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-E-5 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
Notes
No notes.
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | AEM 30-6053 Series 2 Plug & Play EMS, 2006–2008 S2000 AP2 (original ECU pinout) | https://documents.aemelectronics.com/techlibrary_30-6053_series_2_plug___play_ems.pdf | — | 2026-10-05 | ecc8006f849f |
| 4 | vendor_doc | Bosch relay catalogue (mini ISO relays) | https://www.bosch-ibusiness.com/media/downloads/kataloge/relay/2025_10_bosch_relay_catalogue.pdf | archive | 2026-10-05 | 20344cff1ef3 |
| 4 | community_copy | Honda S2000 Service Manual 2000–2008, Fuel and Emissions Systems | https://www.s2000.wiki/view/images/7/7f/Service_Manual_2000-2008.pdf | archive | 2026-10-05 | a470cfc928e9 |
| 4 | vendor_doc | MaxxECU GEN1 pinout (MINI / STREET / SPORT / V1 / RACE / PRO) | http://www.maxxecu.com/webhelp/wirings-maxxecu_pinout.html | archive | 2026-10-05 | 2e37b6814690 |
| 4 | vendor_doc | Omron G8V-RH-1C7T-R-DC12 high-current micro 280 automotive relay datasheet | https://www.alldatasheet.com/datasheet-pdf/pdf/333797/OMRON/G8V-RH-1C7T-R-DC12.html | — | 2026-10-05 | 764a0505a941 |
| 3 | vendor_doc | ScienceofSpeed Link G4X ECU, S2000 2006–09 (product page) | https://www.scienceofspeed.com/s2000-2000-09/scienceofspeed-link-g4x-ecu-s2000-2006-09-enpp-3822.html | archive | 2026-10-05 | 643bc0efd6d7 |