S2000 AP2 2006–09 cable conversion → FuelTech FT450
AP2 2006–09 converted to cable throttle — FuelTech — FT450
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-12
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 2: read the Findings page before cutting any wire |
| Size of the job | 41 wires · 12 connectors · 5 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-A-2 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-A-3 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | FT450-A-A13 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-A-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-A-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-A-8 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-A-9 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-E-3 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | FT450-A-A7 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-A-24 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | SP-0V-1 | FT450-A-A12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | SP-5V1-1 | FT450-A-A14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-A-7 | FT450-A-A18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | SP-0V-1 | FT450-A-A18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-A-6 | FT450-A-A17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-A-16 | FT450-A-A8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-A-15 | FT450-A-A9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-A-14 | FT450-A-A10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-A-13 | FT450-A-A11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-B-5 | FT450-A-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-B-4 | FT450-A-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-B-3 | FT450-A-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-B-2 | FT450-A-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-E-17 | FT450-A-A6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-E-7 | FT450-A-A3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-B-6 | RLY1-R-OUT | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | SP-14V-1 | RLY1-R-IN | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | SP-14V-1 | RLY1-R-COIL+ | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | RLY1-R-COIL- | FT450-A-A4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-A-30 | FT450-A-A20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-B-8 | FT450-A-A24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-E-20 | FT450-A-A23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-E-1 | FT450-A-A26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-B-17 | FT450-A-A25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-E-11 | FT450-A-A16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-E-24 | FT450-A-A15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-A-21 | SP-5V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | SP-5V-1 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | SP-5V-1 | TPS-J-VCC | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | TPS-J-SIG | FT450-A-A22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | TPS-J-GND | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | FT450-A-A13 | FT450-A-A12 | open (OL) | +12 V supply must not touch sensor ground | |
| 2 | FT450-A-A13 | FT450-A-A7 | open (OL) | +12 V supply must not touch power ground | |
| 3 | FT450-A-A12 | FT450-A-A14 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 4 | FT450-A-A12 | RLY1-R-OUT | open (OL) | sensor ground must not touch +12 V supply | |
| 5 | FT450-A-A13 | FT450-A-A14 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 6 | FT450-A-A14 | RLY1-R-OUT | open (OL) | 5 V sensor reference must not touch +12 V supply | |
| 7 | FT450-A-A7 | FT450-A-A14 | open (OL) | power ground must not touch 5 V sensor reference | |
| 8 | FT450-A-A7 | RLY1-R-OUT | open (OL) | power ground must not touch +12 V supply |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
FT450-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A1 | Injector 1 (Bank A) | — | W20 | — | 0.5 | OEM-B-5 | — | — | — |
| A1 | Injector 1 (Bank A) | — | W22 | — | 0.5 | OEM-B-3 | — | — | — |
| A10 | Ignition 3 | — | W18 | — | 0.5 | OEM-A-14 | — | — | — |
| A11 | Ignition 4 | — | W19 | — | 0.5 | OEM-A-13 | — | — | — |
| A12 | Signal ground | — | W11 | — | 0.5 | SP-0V-1 | — | — | — |
| A13 | +12V switched | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| A14 | +5V sensor supply | — | W12 | — | 0.5 | SP-5V1-1 | — | — | — |
| A15 | CAN A LOW | — | W36 | — | 0.5 | OEM-E-24 | — | — | — |
| A16 | CAN A HIGH | — | W35 | — | 0.5 | OEM-E-11 | — | — | — |
| A17 | Phase input (cam) | — | W15 | — | 0.5 | OEM-A-6 | — | — | — |
| A18 | RPM reference (crank -) | — | W13 | — | 0.5 | OEM-A-7 | — | — | — |
| A18 | RPM reference (crank -) | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| A19 | RPM signal (crank +) | — | — | — | — | — | — | — | — |
| A2 | Injector 2 (Bank A) | — | W21 | — | 0.5 | OEM-B-4 | — | — | — |
| A2 | Injector 2 (Bank A) | — | W23 | — | 0.5 | OEM-B-2 | — | — | — |
| A20 | White input 1 | — | W30 | — | 0.5 | OEM-A-30 | — | — | — |
| A21 | White input 2 | — | — | — | — | — | — | — | — |
| A22 | White input 3 (TPS) | — | W40 | — | 0.5 | TPS-J-SIG | — | — | — |
| A23 | White input 4 (oil pressure) | — | W32 | — | 0.5 | OEM-E-20 | — | — | — |
| A24 | White input 5 (water temp) | — | W31 | — | 0.5 | OEM-B-8 | — | — | — |
| A25 | White input 6 (fuel pressure) | — | W34 | — | 0.5 | OEM-B-17 | — | — | — |
| A26 | White input 7 (air temp) | — | W33 | — | 0.5 | OEM-E-1 | — | — | — |
| A3 | Aux 1 | — | W25 | — | 0.5 | OEM-E-7 | — | — | — |
| A4 | Aux 2 | — | W29 | — | 0.5 | RLY1-R-COIL- | — | — | — |
| A5 | Aux 3 | — | — | — | — | — | — | — | — |
| A6 | Aux 4 (fuel pump / relays) | — | W24 | — | 0.5 | OEM-E-17 | — | — | — |
| A7 | Power ground | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| A8 | Ignition 1 | — | W16 | — | 0.5 | OEM-A-16 | — | — | — |
| A9 | Ignition 2 | — | W17 | — | 0.5 | OEM-A-15 | — | — | — |
OEM-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Knock sensor | — | — | — | — | — | — | — | — |
| 2 | Ignition power 2 | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 3 | Ignition power 1 | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 4 | Power ground 2 | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | Power ground 1 | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Cam position sensor (T2) | — | W15 | — | 0.5 | FT450-A-A17 | — | — | — |
| 7 | Crank position sensor (T1) | — | W13 | — | 0.5 | FT450-A-A18 | — | — | — |
| 8 | Logic ground 2 | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 9 | Logic ground 1 | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 10 | A/F sensor heater | — | — | — | — | — | — | — | — |
| 11 | Unused cavity | — | — | — | — | — | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Ignition coil 4 | — | W19 | — | 0.5 | FT450-A-A11 | — | — | — |
| 14 | Ignition coil 3 | — | W18 | — | 0.5 | FT450-A-A10 | — | — | — |
| 15 | Ignition coil 2 | — | W17 | — | 0.5 | FT450-A-A9 | — | — | — |
| 16 | Ignition coil 1 | — | W16 | — | 0.5 | FT450-A-A8 | — | — | — |
| 17 | Unused cavity | — | — | — | — | — | — | — | — |
| 18 | Vehicle speed sensor | — | — | — | — | — | — | — | — |
| 19 | Unused cavity | — | — | — | — | — | — | — | — |
| 20 | Sensor voltage 2 | — | — | — | — | — | — | — | — |
| 21 | Sensor voltage 1 | — | W37 | — | 0.5 | SP-5V-1 | — | — | — |
| 22 | Unused cavity | — | — | — | — | — | — | — | — |
| 23 | Sensor ground 2 | — | — | — | — | — | — | — | — |
| 24 | Sensor ground 1 | — | W10 | — | 0.5 | SP-0V-1 | — | — | — |
| 25 | Accelerator pedal position B | — | — | — | — | — | — | — | — |
| 26 | Accelerator pedal position A | — | — | — | — | — | — | — | — |
| 27 | Unused cavity | — | — | — | — | — | — | — | — |
| 28 | A/F sensor signal − | — | — | — | — | — | — | — | — |
| 29 | Unused cavity | — | — | — | — | — | — | — | — |
| 30 | MAP sensor | — | W30 | — | 0.5 | FT450-A-A20 | — | — | — |
| 31 | A/F sensor signal + | — | — | — | — | — | — | — | — |
OEM-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Unused cavity | — | — | — | — | — | — | — | — |
| 2 | Injector 4 | — | W23 | — | 0.5 | FT450-A-A2 | — | — | — |
| 3 | Injector 3 | — | W22 | — | 0.5 | FT450-A-A1 | — | — | — |
| 4 | Injector 2 | — | W21 | — | 0.5 | FT450-A-A2 | — | — | — |
| 5 | Injector 1 | — | W20 | — | 0.5 | FT450-A-A1 | — | — | — |
| 6 | VTEC solenoid | — | W26 | — | 0.5 | RLY1-R-OUT | — | — | — |
| 7 | Unused cavity | — | — | — | — | — | — | — | — |
| 8 | Coolant temp sensor | — | W31 | — | 0.5 | FT450-A-A24 | — | — | — |
| 9 | Unused cavity | — | — | — | — | — | — | — | — |
| 10 | Alternator L signal | — | — | — | — | — | — | — | — |
| 11 | VTEC oil pressure switch | — | — | — | — | — | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Alternator FR signal | — | — | — | — | — | — | — | — |
| 14 | Unused cavity | — | — | — | — | — | — | — | — |
| 15 | Engine mount control solenoid | — | — | — | — | — | — | — | — |
| 16 | Unused cavity | — | — | — | — | — | — | — | — |
| 17 | Intake air temp sensor | — | W34 | — | 0.5 | FT450-A-A25 | — | — | — |
| 18 | Alternator control | — | — | — | — | — | — | — | — |
| 19 | Throttle actuator command to throttle control module (SEFD) | — | — | — | — | — | — | — | — |
| 20 | Throttle actuator command to throttle control module (SEDF) | — | — | — | — | — | — | — | — |
| 21 | Evap canister purge valve | — | — | — | — | — | — | — | — |
| 22 | Unused cavity | — | — | — | — | — | — | — | — |
| 23 | Unused cavity | — | — | — | — | — | — | — | — |
| 24 | Unused cavity | — | — | — | — | — | — | — | — |
OEM-D
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Cruise set switch | — | — | — | — | — | — | — | — |
| 2 | Unused cavity | — | — | — | — | — | — | — | — |
| 3 | Unused cavity | — | — | — | — | — | — | — | — |
| 4 | Cruise main switch | — | — | — | — | — | — | — | — |
| 5 | Unused cavity | — | — | — | — | — | — | — | — |
| 6 | Unused cavity | — | — | — | — | — | — | — | — |
| 7 | Cruise resume switch | — | — | — | — | — | — | — | — |
| 8 | Brake pedal position switch | — | — | — | — | — | — | — | — |
| 9 | Cruise clutch signal | — | — | — | — | — | — | — | — |
| 10 | Unused cavity | — | — | — | — | — | — | — | — |
| 11 | Unused cavity | — | — | — | — | — | — | — | — |
| 12 | Unused cavity | — | — | — | — | — | — | — | — |
| 13 | Unused cavity | — | — | — | — | — | — | — | — |
| 14 | Unused cavity | — | — | — | — | — | — | — | — |
| 15 | Throttle actuator relay | — | — | — | — | — | — | — | — |
| 16 | Unused cavity | — | — | — | — | — | — | — | — |
| 17 | Unused cavity | — | — | — | — | — | — | — | — |
OEM-E
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Coolant temp sensor 2 | — | W33 | — | 0.5 | FT450-A-A26 | — | — | — |
| 2 | Unused cavity | — | — | — | — | — | — | — | — |
| 3 | Logic ground 3 | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 4 | Sensor ground 3 | — | — | — | — | — | — | — | — |
| 5 | Sensor voltage 3 | — | — | — | — | — | — | — | — |
| 6 | Unused cavity | — | — | — | — | — | — | — | — |
| 7 | Main relay control | — | W25 | — | 0.5 | FT450-A-A3 | — | — | — |
| 8 | A/F sensor heater relay | — | — | — | — | — | — | — | — |
| 9 | Ignition signal | — | — | — | — | — | — | — | — |
| 10 | Unused cavity | — | — | — | — | — | — | — | — |
| 11 | CAN H | — | W35 | — | 0.5 | FT450-A-A16 | — | — | — |
| 12 | Radiator fan control | — | — | — | — | — | — | — | — |
| 13 | Multiplex communication | — | — | — | — | — | — | — | — |
| 14 | Fuel tank pressure sensor | — | — | — | — | — | — | — | — |
| 15 | Electrical load detector | — | — | — | — | — | — | — | — |
| 16 | Power steering load detector | — | — | — | — | — | — | — | — |
| 17 | Fuel pump relay | — | W24 | — | 0.5 | FT450-A-A6 | — | — | — |
| 18 | A/C clutch relay | — | — | — | — | — | — | — | — |
| 19 | Evap canister vent shut valve | — | — | — | — | — | — | — | — |
| 20 | Secondary O2 sensor | — | W32 | — | 0.5 | FT450-A-A23 | — | — | — |
| 21 | Secondary O2 heater | — | — | — | — | — | — | — | — |
| 22 | Brake pedal switch | — | — | — | — | — | — | — | — |
| 23 | Unused cavity | — | — | — | — | — | — | — | — |
| 24 | CAN L | — | W36 | — | 0.5 | FT450-A-A15 | — | — | — |
| 25 | Engine speed pulse (tacho) | — | — | — | — | — | — | — | — |
| 26 | Vehicle speed output | — | — | — | — | — | — | — | — |
| 27 | Immobilizer code | — | — | — | — | — | — | — | — |
| 28 | A/C switch signal | — | — | — | — | — | — | — | — |
| 29 | Service check signal | — | — | — | — | — | — | — | — |
| 30 | Write enable signal | — | — | — | — | — | — | — | — |
| 31 | Unused cavity | — | — | — | — | — | — | — | — |
RLY1-R
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| COIL+ | Relay coil positive (switched +12 V) | — | W28 | — | 0.5 | SP-14V-1 | — | — | — |
| COIL- | Relay coil negative (ECU low-side driver) | — | W29 | — | 0.5 | FT450-A-A4 | — | — | — |
| IN | Relay contact input (switched +12 V) | — | W27 | — | 0.5 | SP-14V-1 | — | — | — |
| OUT | Relay contact output (switched +12 V to load) | — | W26 | — | 0.5 | OEM-B-6 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W10 | — | 0.5 | OEM-A-24 | — | — | — |
| 1 | — | — | W11 | — | 0.5 | FT450-A-A12 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | FT450-A-A18 | — | — | — |
| 1 | — | — | W41 | — | 0.5 | TPS-J-GND | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-A-2 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-A-3 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | FT450-A-A13 | — | — | — |
| 1 | — | — | W27 | — | 0.5 | RLY1-R-IN | — | — | — |
| 1 | — | — | W28 | — | 0.5 | RLY1-R-COIL+ | — | — | — |
SP-5V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W37 | — | 0.5 | OEM-A-21 | — | — | — |
| 1 | — | — | W38 | — | 0.5 | SP-5V1-1 | — | — | — |
| 1 | — | — | W39 | — | 0.5 | TPS-J-VCC | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W38 | — | 0.5 | SP-5V-1 | — | — | — |
| 1 | — | — | W12 | — | 0.5 | FT450-A-A14 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W5 | — | 0.85 | OEM-A-5 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-A-8 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | OEM-E-3 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | FT450-A-A7 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-A-9 | — | — | — |
| 1 | — | — | W4 | — | 0.85 | OEM-A-4 | — | — | — |
TPS-J
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| VCC | 5V supply in | — | W39 | — | 0.5 | SP-5V-1 | — | — | — |
| SIG | Throttle position signal | — | W40 | — | 0.5 | FT450-A-A22 | — | — | — |
| GND | Sensor ground | — | W41 | — | 0.5 | SP-0V-1 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-A-1 | Knock sensor | knock_in | — | — | — | single_source | |
| OEM-A-10 | A/F sensor heater | low_side_out | — | — | — | single_source | |
| OEM-A-11 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-12 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-13 | Ignition coil 4 | ignition_out | FT450-A-A11 | Ignition 4 | ignition_out | single_source | |
| OEM-A-14 | Ignition coil 3 | ignition_out | FT450-A-A10 | Ignition 3 | ignition_out | single_source | |
| OEM-A-15 | Ignition coil 2 | ignition_out | FT450-A-A9 | Ignition 2 | ignition_out | single_source | |
| OEM-A-16 | Ignition coil 1 | ignition_out | FT450-A-A8 | Ignition 1 | ignition_out | single_source | |
| OEM-A-17 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-18 | Vehicle speed sensor | digital_in | — | — | — | single_source | |
| OEM-A-19 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-2 | Ignition power 2 | power_in | FT450-A-A13 + RLY1-R-COIL+ + RLY1-R-IN | +12V switched + Relay coil positive (switched +12 V) + Relay contact input (switched +12 V) | power_in + power_out | single_source | |
| OEM-A-20 | Sensor voltage 2 | vref | — | — | — | corroborated | |
| OEM-A-21 | Sensor voltage 1 | vref | FT450-A-A14 + TPS-J-VCC | +5V sensor supply + 5V supply in | power_in + vref | single_source | |
| OEM-A-22 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-23 | Sensor ground 2 | sensor_ground | — | — | — | corroborated | |
| OEM-A-24 | Sensor ground 1 | sensor_ground | FT450-A-A12 + FT450-A-A18 + TPS-J-GND | Signal ground + RPM reference (crank -) + Sensor ground | sensor_ground + trigger_in | single_source | |
| OEM-A-25 | Accelerator pedal position B | analog_in | — | — | — | corroborated | |
| OEM-A-26 | Accelerator pedal position A | analog_in | — | — | — | corroborated | |
| OEM-A-27 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-28 | A/F sensor signal − | — | — | — | — | single_source | |
| OEM-A-29 | Unused cavity | — | — | — | — | unverified | |
| OEM-A-3 | Ignition power 1 | power_in | FT450-A-A13 + RLY1-R-COIL+ + RLY1-R-IN | +12V switched + Relay coil positive (switched +12 V) + Relay contact input (switched +12 V) | power_in + power_out | single_source | |
| OEM-A-30 | MAP sensor | analog_in | FT450-A-A20 | White input 1 | analog_in | single_source | |
| OEM-A-31 | A/F sensor signal + | — | — | — | — | single_source | |
| OEM-A-4 | Power ground 2 | ground | FT450-A-A7 | Power ground | ground | single_source | |
| OEM-A-5 | Power ground 1 | ground | FT450-A-A7 | Power ground | ground | single_source | |
| OEM-A-6 | Cam position sensor (T2) | trigger_in | FT450-A-A17 | Phase input (cam) | trigger_in | single_source | |
| OEM-A-7 | Crank position sensor (T1) | trigger_in | FT450-A-A12 + FT450-A-A18 + TPS-J-GND | Signal ground + RPM reference (crank -) + Sensor ground | sensor_ground + trigger_in | single_source | |
| OEM-A-8 | Logic ground 2 | ground | FT450-A-A7 | Power ground | ground | single_source | |
| OEM-A-9 | Logic ground 1 | ground | FT450-A-A7 | Power ground | ground | single_source | |
| OEM-B-1 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-10 | Alternator L signal | — | — | — | — | single_source | |
| OEM-B-11 | VTEC oil pressure switch | digital_in | — | — | — | single_source | |
| OEM-B-12 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-13 | Alternator FR signal | analog_in | — | — | — | single_source | |
| OEM-B-14 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-15 | Engine mount control solenoid | low_side_out | — | — | — | single_source | |
| OEM-B-16 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-17 | Intake air temp sensor | temp_in | FT450-A-A25 | White input 6 (fuel pressure) | analog_in | single_source | |
| OEM-B-18 | Alternator control | low_side_out | — | — | — | single_source | |
| OEM-B-19 | Throttle actuator command to throttle control module (SEFD) | — | — | — | — | conflict | |
| OEM-B-2 | Injector 4 | injector_out | FT450-A-A2 | Injector 2 (Bank A) | injector_out | single_source | |
| OEM-B-20 | Throttle actuator command to throttle control module (SEDF) | — | — | — | — | conflict | |
| OEM-B-21 | Evap canister purge valve | low_side_out | — | — | — | single_source | |
| OEM-B-22 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-23 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-24 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-3 | Injector 3 | injector_out | FT450-A-A1 | Injector 1 (Bank A) | injector_out | single_source | |
| OEM-B-4 | Injector 2 | injector_out | FT450-A-A2 | Injector 2 (Bank A) | injector_out | single_source | |
| OEM-B-5 | Injector 1 | injector_out | FT450-A-A1 | Injector 1 (Bank A) | injector_out | single_source | |
| OEM-B-6 | VTEC solenoid | high_side_out | RLY1-R-OUT | Relay contact output (switched +12 V to load) | power_out | single_source | |
| OEM-B-7 | Unused cavity | — | — | — | — | unverified | |
| OEM-B-8 | Coolant temp sensor | temp_in | FT450-A-A24 | White input 5 (water temp) | temp_in | single_source | |
| OEM-B-9 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-1 | Cruise set switch | digital_in | — | — | — | single_source | |
| OEM-D-10 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-11 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-12 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-13 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-14 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-15 | Throttle actuator relay | low_side_out | — | — | — | single_source | |
| OEM-D-16 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-17 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-2 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-3 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-4 | Cruise main switch | digital_in | — | — | — | single_source | |
| OEM-D-5 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-6 | Unused cavity | — | — | — | — | unverified | |
| OEM-D-7 | Cruise resume switch | digital_in | — | — | — | single_source | |
| OEM-D-8 | Brake pedal position switch | digital_in | — | — | — | single_source | |
| OEM-D-9 | Cruise clutch signal | digital_in | — | — | — | single_source | |
| OEM-E-1 | Coolant temp sensor 2 | temp_in | FT450-A-A26 | White input 7 (air temp) | temp_in | single_source | |
| OEM-E-10 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-11 | CAN H | can_h | FT450-A-A16 | CAN A HIGH | can_h | single_source | |
| OEM-E-12 | Radiator fan control | low_side_out | — | — | — | single_source | |
| OEM-E-13 | Multiplex communication | serial | — | — | — | single_source | |
| OEM-E-14 | Fuel tank pressure sensor | analog_in | — | — | — | single_source | |
| OEM-E-15 | Electrical load detector | analog_in | — | — | — | single_source | |
| OEM-E-16 | Power steering load detector | analog_in | — | — | — | corroborated | |
| OEM-E-17 | Fuel pump relay | low_side_out | FT450-A-A6 | Aux 4 (fuel pump / relays) | low_side_out | single_source | |
| OEM-E-18 | A/C clutch relay | low_side_out | — | — | — | single_source | |
| OEM-E-19 | Evap canister vent shut valve | low_side_out | — | — | — | single_source | |
| OEM-E-2 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-20 | Secondary O2 sensor | lambda_nb_in | FT450-A-A23 | White input 4 (oil pressure) | analog_in | single_source | |
| OEM-E-21 | Secondary O2 heater | low_side_out | — | — | — | single_source | |
| OEM-E-22 | Brake pedal switch | digital_in | — | — | — | single_source | |
| OEM-E-23 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-24 | CAN L | can_l | FT450-A-A15 | CAN A LOW | can_l | single_source | |
| OEM-E-25 | Engine speed pulse (tacho) | tacho_out | — | — | — | single_source | |
| OEM-E-26 | Vehicle speed output | tacho_out | — | — | — | single_source | |
| OEM-E-27 | Immobilizer code | — | — | — | — | single_source | |
| OEM-E-28 | A/C switch signal | digital_in | — | — | — | single_source | |
| OEM-E-29 | Service check signal | — | — | — | — | single_source | |
| OEM-E-3 | Logic ground 3 | ground | FT450-A-A7 | Power ground | ground | single_source | |
| OEM-E-30 | Write enable signal | — | — | — | — | single_source | |
| OEM-E-31 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-4 | Sensor ground 3 | sensor_ground | — | — | — | corroborated | |
| OEM-E-5 | Sensor voltage 3 | vref | — | — | — | corroborated | |
| OEM-E-6 | Unused cavity | — | — | — | — | unverified | |
| OEM-E-7 | Main relay control | low_side_out | FT450-A-A3 | Aux 1 | low_side_out | single_source | |
| OEM-E-8 | A/F sensor heater relay | low_side_out | — | — | — | single_source | |
| OEM-E-9 | Ignition signal | digital_in | — | — | — | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-A-2 | SP-14V-1 | 0.85 | no route | Ignition power 2 | — | |
| W2 | OEM-A-3 | SP-14V-1 | 0.85 | no route | Ignition power 1 | — | |
| W3 | SP-14V-1 | FT450-A-A13 | 0.85 | no route | +12V switched | — | |
| W4 | OEM-A-4 | SP-GND-1 | 0.85 | no route | Power ground 2 | — | |
| W5 | OEM-A-5 | SP-GND-1 | 0.85 | no route | Power ground 1 | — | |
| W6 | OEM-A-8 | SP-GND-1 | 0.85 | no route | Logic ground 2 | — | |
| W7 | OEM-A-9 | SP-GND-1 | 0.85 | no route | Logic ground 1 | — | |
| W8 | OEM-E-3 | SP-GND-1 | 0.85 | no route | Logic ground 3 | — | |
| W9 | SP-GND-1 | FT450-A-A7 | 0.85 | no route | Power ground | — | |
| W10 | OEM-A-24 | SP-0V-1 | 0.5 | no route | Sensor ground 1 | — | |
| W11 | SP-0V-1 | FT450-A-A12 | 0.5 | no route | Signal ground | — | |
| W12 | SP-5V1-1 | FT450-A-A14 | 0.5 | no route | +5V sensor supply | — | |
| W13 | OEM-A-7 | FT450-A-A18 | 0.5 | no route | Crank position sensor (T1) | — | |
| W14 | SP-0V-1 | FT450-A-A18 | 0.5 | no route | RPM reference (crank -) | — | |
| W15 | OEM-A-6 | FT450-A-A17 | 0.5 | no route | Cam position sensor (T2) | — | |
| W16 | OEM-A-16 | FT450-A-A8 | 0.5 | no route | Ignition coil 1 | — | |
| W17 | OEM-A-15 | FT450-A-A9 | 0.5 | no route | Ignition coil 2 | — | |
| W18 | OEM-A-14 | FT450-A-A10 | 0.5 | no route | Ignition coil 3 | — | |
| W19 | OEM-A-13 | FT450-A-A11 | 0.5 | no route | Ignition coil 4 | — | |
| W20 | OEM-B-5 | FT450-A-A1 | 0.5 | no route | Injector 1 | — | |
| W21 | OEM-B-4 | FT450-A-A2 | 0.5 | no route | Injector 2 | — | |
| W22 | OEM-B-3 | FT450-A-A1 | 0.5 | no route | Injector 3 | — | |
| W23 | OEM-B-2 | FT450-A-A2 | 0.5 | no route | Injector 4 | — | |
| W24 | OEM-E-17 | FT450-A-A6 | 0.5 | no route | Fuel pump relay | — | |
| W25 | OEM-E-7 | FT450-A-A3 | 0.5 | no route | Main relay control | — | |
| W26 | OEM-B-6 | RLY1-R-OUT | 0.5 | no route | VTEC solenoid | — | |
| W27 | SP-14V-1 | RLY1-R-IN | 0.5 | no route | Relay contact input (switched +12 V) | — | |
| W28 | SP-14V-1 | RLY1-R-COIL+ | 0.5 | no route | Relay coil positive (switched +12 V) | — | |
| W29 | RLY1-R-COIL- | FT450-A-A4 | 0.5 | no route | Relay coil negative (ECU low-side driver) | — | |
| W30 | OEM-A-30 | FT450-A-A20 | 0.5 | no route | MAP sensor | — | |
| W31 | OEM-B-8 | FT450-A-A24 | 0.5 | no route | Coolant temp sensor | — | |
| W32 | OEM-E-20 | FT450-A-A23 | 0.5 | no route | Secondary O2 sensor | — | |
| W33 | OEM-E-1 | FT450-A-A26 | 0.5 | no route | Coolant temp sensor 2 | — | |
| W34 | OEM-B-17 | FT450-A-A25 | 0.5 | no route | Intake air temp sensor | — | |
| W35 | OEM-E-11 | FT450-A-A16 | 0.5 | no route | CAN H | — | |
| W36 | OEM-E-24 | FT450-A-A15 | 0.5 | no route | CAN L | — | |
| W37 | OEM-A-21 | SP-5V-1 | 0.5 | no route | Sensor voltage 1 | — | |
| W38 | SP-5V-1 | SP-5V1-1 | 0.5 | no route | — | — | |
| W39 | SP-5V-1 | TPS-J-VCC | 0.5 | no route | 5V supply in | — | |
| W40 | TPS-J-SIG | FT450-A-A22 | 0.5 | no route | Throttle position signal | — | |
| W41 | TPS-J-GND | SP-0V-1 | 0.5 | no route | Sensor ground | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | S2K-0609-ECU-A | Honda | S2000 2006–09 ECU plug A (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-B | Honda | S2000 2006–09 ECU plug B (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-D | Honda | S2000 2006–09 ECU plug D (P/N unknown) | 1.000 | ea |
| connector | S2K-0609-ECU-E | Honda | S2000 2006–09 ECU plug E (P/N unknown) | 1.000 | ea |
| connector | TPS-3W | Generic | 3-way throttle position sensor plug (match to your throttle body) | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (13)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | NET_MERGED | FT450-A-A1 + OEM-B-3 + OEM-B-5 | 2 different OEM functions share one net: OEM-B-3 Injector 3; OEM-B-5 Injector 1 |
| error | NET_MERGED | FT450-A-A2 + OEM-B-2 + OEM-B-4 | 2 different OEM functions share one net: OEM-B-2 Injector 4; OEM-B-4 Injector 2 |
| warn | LOAD_UNKNOWN | FT450-A-A1 | FT450-A-A1 "Injector 1 (Bank A)" drives OEM-B-3 Injector 3, OEM-B-5 Injector 1 (load 2.4 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | FT450-A-A2 | FT450-A-A2 "Injector 2 (Bank A)" drives OEM-B-2 Injector 4, OEM-B-4 Injector 2 (load 2.4 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | FT450-A-A3 | FT450-A-A3 "Aux 1" drives OEM-E-7 Main relay control (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | FT450-A-A6 | FT450-A-A6 "Aux 4 (fuel pump / relays)" drives OEM-E-17 Fuel pump relay (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | RLY1-R-OUT | RLY1-R-OUT "Relay contact output (switched +12 V to load)" drives OEM-B-6 VTEC solenoid (load 1.0 A) but its current rating is unknown. Check the ECU manual. |
| info | NET_FAMILY | OEM-A-7 ↔ OEM-A-24 | OEM-A-7 "Crank position sensor (T1)" [trigger_in] is wired to OEM-A-24 "Sensor ground 1" [sensor_ground]. Trigger return tied to sensor/trigger ground: correct for single-ended trigger inputs. |
| info | NET_FAMILY | OEM-B-17 ↔ FT450-A-A25 | OEM-B-17 "Intake air temp sensor" [temp_in] is wired to FT450-A-A25 "White input 6 (fuel pressure)" [analog_in]. Thermistor on a plain analog input needs a pull-up; check the channel can enable one. |
| info | PIN_UNSOURCED | TPS-J-GND | TPS-J-GND "Sensor ground" has no recorded source. |
| info | PIN_UNSOURCED | TPS-J-SIG | TPS-J-SIG "Throttle position signal" has no recorded source. |
| info | PIN_UNSOURCED | TPS-J-VCC | TPS-J-VCC "5V supply in" has no recorded source. |
| info | UNMAPPED | OEM | 36 optional OEM pins are not mapped: OEM-A-1 Knock sensor; OEM-A-10 A/F sensor heater; OEM-A-18 Vehicle speed sensor; OEM-A-28 A/F sensor signal −; OEM-A-31 A/F sensor signal +; OEM-B-10 Alternator L signal; OEM-B-11 VTEC oil pressure switch; OEM-B-13 Alternator FR signal; OEM-B-15 Engine mount control solenoid; OEM-B-18 Alternator control; OEM-B-19 Throttle actuator command to throttle control module (SEFD); OEM-B-20 Throttle actuator command to throttle control module (SEDF); OEM-B-21 Evap canister purge valve; OEM-D-1 Cruise set switch; OEM-D-15 Throttle actuator relay; OEM-D-4 Cruise main switch; OEM-D-7 Cruise resume switch; OEM-D-8 Brake pedal position switch; OEM-D-9 Cruise clutch signal; OEM-E-12 Radiator fan control; OEM-E-13 Multiplex communication; OEM-E-14 Fuel tank pressure sensor; OEM-E-15 Electrical load detector; OEM-E-16 Power steering load detector; OEM-E-18 A/C clutch relay; OEM-E-19 Evap canister vent shut valve; OEM-E-21 Secondary O2 heater; OEM-E-22 Brake pedal switch; OEM-E-25 Engine speed pulse (tacho); OEM-E-26 Vehicle speed output; OEM-E-27 Immobilizer code; OEM-E-28 A/C switch signal; OEM-E-29 Service check signal; OEM-E-30 Write enable signal; OEM-E-8 A/F sensor heater relay; OEM-E-9 Ignition signal |
Accepted (6)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-A-20 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-A-23 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-A-25 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-A-26 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-E-4 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
| REQUIRED_UNMAPPED | OEM-E-5 | DBW removed: accelerator pedal dropped (its signal, 5 V supply and sensor ground are no longer needed). | mapping-proposal |
Notes
Fit check: unconfirmed. Confirm these before building: - Trigger pattern for Honda F22C1 not found in the ECU's docs (Confirmed absent from documented trigger/decoder list. Trigger F22C1 is not in the FuelTech docs (open), but the 2006-09 AP2 has drive-by-wire and FT450 has no DBW output (spec table p.8 'DBW: NO', 0 Yellow outputs) -> not_suitable for F...) - No knock input; the stock knock sensor would be unused
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | AEM 30-6053 Series 2 Plug & Play EMS, 2006–2008 S2000 AP2 (original ECU pinout) | https://documents.aemelectronics.com/techlibrary_30-6053_series_2_plug___play_ems.pdf | — | 2026-10-05 | ecc8006f849f |
| 4 | vendor_doc | Bosch relay catalogue (mini ISO relays) | https://www.bosch-ibusiness.com/media/downloads/kataloge/relay/2025_10_bosch_relay_catalogue.pdf | archive | 2026-10-05 | 20344cff1ef3 |
| 4 | vendor_doc | FuelTech FT450/FT550 ready harness manual (4 & 6 cylinder) — FT450 Connector A pinout | http://ftmanager.fueltech.com.br/downloads/manual/Portugues/Chicote_pronto_FT450-FT550.pdf | — | — | — |
| 4 | community_copy | Honda S2000 Service Manual 2000–2008, Fuel and Emissions Systems | https://www.s2000.wiki/view/images/7/7f/Service_Manual_2000-2008.pdf | archive | 2026-10-05 | a470cfc928e9 |
| 4 | vendor_doc | Omron G8V-RH-1C7T-R-DC12 high-current micro 280 automotive relay datasheet | https://www.alldatasheet.com/datasheet-pdf/pdf/333797/OMRON/G8V-RH-1C7T-R-DC12.html | — | 2026-10-05 | 764a0505a941 |
| 3 | vendor_doc | ScienceofSpeed Link G4X ECU, S2000 2006–09 (product page) | https://www.scienceofspeed.com/s2000-2000-09/scienceofspeed-link-g4x-ecu-s2000-2006-09-enpp-3822.html | archive | 2026-10-05 | 643bc0efd6d7 |