BMW 3 Series E46 M3 2001–2006 (S54) → Link G5 Voodoo Pro V1 (auto)
BMW 3 Series E46 M3 2001–2006 (S54) — Link — G5 Voodoo Pro V1
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-12
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 10: read the Findings page before cutting any wire |
| Size of the job | 48 wires · 10 connectors · 1 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-X60001-4 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-X60001-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | OEM-X60001-6 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-X60001-9 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-X60005-5 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-X60004-14 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-X60004-9 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | SP-5V1-1 | G5VOODOOPROV-A-A32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | OEM-X60003-3 | G5VOODOOPROV-A-A8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-X60003-30 | G5VOODOOPROV-A-A9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-X60003-29 | G5VOODOOPROV-A-A30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-X60003-33 | G5VOODOOPROV-B-B9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-X60003-34 | G5VOODOOPROV-B-B8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-X60005-6 | G5VOODOOPROV-A-A13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-X60005-7 | G5VOODOOPROV-A-A12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-X60005-4 | G5VOODOOPROV-A-A11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-X60005-8 | G5VOODOOPROV-A-A10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-X60005-1 | G5VOODOOPROV-B-B13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-X60005-9 | G5VOODOOPROV-B-B12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-X60003-13 | G5VOODOOPROV-A-A4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-X60003-6 | G5VOODOOPROV-A-A3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-X60003-26 | G5VOODOOPROV-A-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-X60003-7 | G5VOODOOPROV-A-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-X60003-11 | G5VOODOOPROV-B-B4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-X60003-8 | G5VOODOOPROV-B-B3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-X60003-1 | G5VOODOOPROV-A-A17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-X60003-32 | G5VOODOOPROV-A-A22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-X60004-8 | G5VOODOOPROV-A-A33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-X60003-31 | G5VOODOOPROV-A-A14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-X60004-13 | G5VOODOOPROV-B-B33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-X60003-28 | G5VOODOOPROV-A-A15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-X60001-1 | G5VOODOOPROV-A-A21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-X60002-23 | G5VOODOOPROV-A-A20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-X60004-10 | G5VOODOOPROV-A-A19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-X60002-1 | G5VOODOOPROV-E-E15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-X60002-12 | G5VOODOOPROV-E-E22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-X60002-2 | G5VOODOOPROV-A-A18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-X60002-6 | G5VOODOOPROV-A-A29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-X60003-10 | G5VOODOOPROV-A-A28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-X60003-12 | G5VOODOOPROV-A-A27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-X60003-21 | G5VOODOOPROV-A-A26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-X60003-9 | G5VOODOOPROV-B-B2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-X60002-14 | G5VOODOOPROV-B-B15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-X60002-16 | G5VOODOOPROV-B-B16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-X60003-27 | G5VOODOOPROV-A-A16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-X60003-44 | G5VOODOOPROV-B-B6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | OEM-X60003-16 | G5VOODOOPROV-A-A31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | OEM-X60003-50 | G5VOODOOPROV-A-A23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | OEM-X60001-4 | G5VOODOOPROV-A-A32 | open (OL) | power ground must not touch 5 V sensor reference |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
G5VOODOOPROV-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A1 | Injection 4 | — | W23 | — | 0.5 | OEM-X60003-7 | — | — | — |
| A10 | Ignition 4 | — | W17 | — | 0.5 | OEM-X60005-8 | — | — | — |
| A11 | Ignition 3 | — | W16 | — | 0.5 | OEM-X60005-4 | — | — | — |
| A12 | Ignition 2 | — | W15 | — | 0.5 | OEM-X60005-7 | — | — | — |
| A13 | Ignition 1 | — | W14 | — | 0.5 | OEM-X60005-6 | — | — | — |
| A14 | Analogue Volt 4 | — | W29 | — | 0.5 | OEM-X60003-31 | — | — | — |
| A15 | Analogue Temp 1 | — | W31 | — | 0.5 | OEM-X60003-28 | — | — | — |
| A16 | Analogue Temp 2 | — | W45 | — | 0.5 | OEM-X60003-27 | — | — | — |
| A17 | Analogue Volt 1 | — | W26 | — | 0.5 | OEM-X60003-1 | — | — | — |
| A18 | Aux 4 | — | W37 | — | 0.5 | OEM-X60002-2 | — | — | — |
| A19 | Aux 3 | — | W34 | — | 0.5 | OEM-X60004-10 | — | — | — |
| A2 | Injection 3 | — | W22 | — | 0.5 | OEM-X60003-26 | — | — | — |
| A20 | Aux 2 | — | W33 | — | 0.5 | OEM-X60002-23 | — | — | — |
| A21 | Aux 1 | — | W32 | — | 0.5 | OEM-X60001-1 | — | — | — |
| A22 | Analogue Volt 2 | — | W27 | — | 0.5 | OEM-X60003-32 | — | — | — |
| A23 | Digital Input 3 | — | W48 | — | 0.5 | OEM-X60003-50 | — | — | — |
| A26 | Aux 8 | — | W41 | — | 0.5 | OEM-X60003-21 | — | — | — |
| A27 | Aux 7 | — | W40 | — | 0.5 | OEM-X60003-12 | — | — | — |
| A28 | Aux 6 | — | W39 | — | 0.5 | OEM-X60003-10 | — | — | — |
| A29 | Aux 5 | — | W38 | — | 0.5 | OEM-X60002-6 | — | — | — |
| A3 | Injection 2 | — | W21 | — | 0.5 | OEM-X60003-6 | — | — | — |
| A30 | Digital Input 1 | — | W11 | — | 0.5 | OEM-X60003-29 | — | — | — |
| A31 | Digital Input 2 | — | W47 | — | 0.5 | OEM-X60003-16 | — | — | — |
| A32 | +5V Out | — | W8 | — | 0.5 | SP-5V1-1 | — | — | — |
| A33 | Analogue Volt 3 | — | W28 | — | 0.5 | OEM-X60004-8 | — | — | — |
| A4 | Injection 1 | — | W20 | — | 0.5 | OEM-X60003-13 | — | — | — |
| A6 | Ignition Switch | — | — | — | — | — | — | — | — |
| A8 | Trigger 1 | — | W9 | — | 0.5 | OEM-X60003-3 | — | — | — |
| A9 | Trigger 2 | — | W10 | — | 0.5 | OEM-X60003-30 | — | — | — |
G5VOODOOPROV-B
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| B1 | Injection 8 | — | — | — | — | — | — | — | — |
| B10 | Ignition 8 | — | — | — | — | — | — | — | — |
| B11 | Ignition 7 | — | — | — | — | — | — | — | — |
| B12 | Ignition 6 | — | W19 | — | 0.5 | OEM-X60005-9 | — | — | — |
| B13 | Ignition 5 | — | W18 | — | 0.5 | OEM-X60005-1 | — | — | — |
| B14 | Analogue Volt 14 | — | — | — | — | — | — | — | — |
| B15 | Analogue Volt 6 | — | W43 | — | 0.5 | OEM-X60002-14 | — | — | — |
| B16 | Analogue Volt 7 | — | W44 | — | 0.5 | OEM-X60002-16 | — | — | — |
| B18 | Aux 9 | — | — | — | — | — | — | — | — |
| B19 | Digital Input 6 | — | — | — | — | — | — | — | — |
| B2 | Injection 7 | — | W42 | — | 0.5 | OEM-X60003-9 | — | — | — |
| B20 | Digital Input 5 | — | — | — | — | — | — | — | — |
| B21 | Digital Input 4 | — | — | — | — | — | — | — | — |
| B23 | Analogue Volt 8 | — | — | — | — | — | — | — | — |
| B24 | Analogue Volt 9 | — | — | — | — | — | — | — | — |
| B26 | Aux 10 | — | — | — | — | — | — | — | — |
| B27 | Digital Input 10 | — | — | — | — | — | — | — | — |
| B28 | Digital Input 9 | — | — | — | — | — | — | — | — |
| B29 | Digital Input 8 | — | — | — | — | — | — | — | — |
| B3 | Injection 6 | — | W25 | — | 0.5 | OEM-X60003-8 | — | — | — |
| B30 | Digital Input 7 | — | — | — | — | — | — | — | — |
| B31 | Analogue Volt 10 | — | — | — | — | — | — | — | — |
| B32 | Analogue Volt 11 | — | — | — | — | — | — | — | — |
| B33 | Analogue Volt 5 | — | W30 | — | 0.5 | OEM-X60004-13 | — | — | — |
| B4 | Injection 5 | — | W24 | — | 0.5 | OEM-X60003-11 | — | — | — |
| B6 | Analogue Temp 3 | — | W46 | — | 0.5 | OEM-X60003-44 | — | — | — |
| B7 | Analogue Temp 4 | — | — | — | — | — | — | — | — |
| B8 | Knock 2 | — | W13 | — | 0.5 | OEM-X60003-34 | — | — | — |
| B9 | Knock 1 | — | W12 | — | 0.5 | OEM-X60003-33 | — | — | — |
G5VOODOOPROV-E
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| E1 | Injection 12 | — | — | — | — | — | — | — | — |
| E10 | Injection 14 / Ignition 10 | — | — | — | — | — | — | — | — |
| E11 | Injection 13 / Ignition 9 | — | — | — | — | — | — | — | — |
| E12 | Analogue Volt 12 | — | — | — | — | — | — | — | — |
| E13 | Analogue Volt 13 | — | — | — | — | — | — | — | — |
| E14 | Aux 11 | — | — | — | — | — | — | — | — |
| E15 | Aux 13 / WB Heater 1 | — | W35 | — | 0.5 | OEM-X60002-1 | — | — | — |
| E16 | RE 1 | — | — | — | — | — | — | — | — |
| E17 | IPE 1 | — | — | — | — | — | — | — | — |
| E18 | APE 1 | — | — | — | — | — | — | — | — |
| E19 | MES 1 | — | — | — | — | — | — | — | — |
| E2 | Injection 11 | — | — | — | — | — | — | — | — |
| E20 | Aux 12 | — | — | — | — | — | — | — | — |
| E22 | Aux 14 / WB Heater 2 | — | W36 | — | 0.5 | OEM-X60002-12 | — | — | — |
| E23 | RE 2 | — | — | — | — | — | — | — | — |
| E24 | IPE 2 | — | — | — | — | — | — | — | — |
| E25 | APE 2 | — | — | — | — | — | — | — | — |
| E26 | MES 2 | — | — | — | — | — | — | — | — |
| E3 | Injection 10 | — | — | — | — | — | — | — | — |
| E4 | Injection 9 | — | — | — | — | — | — | — | — |
| E8 | Injection 16 / Ignition 12 | — | — | — | — | — | — | — | — |
| E9 | Injection 15 / Ignition 11 | — | — | — | — | — | — | — | — |
OEM-X60001
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector relay control | — | W32 | — | 0.5 | G5VOODOOPROV-A-A21 | — | — | — |
| 2 | DBW output-stage supply (P_DKSM+) | — | — | — | — | — | — | — | — |
| 4 | Power ground | — | W1 | — | 0.85 | SP-GND-1 | — | — | — |
| 5 | Power ground | — | W2 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Power ground | — | W3 | — | 0.85 | SP-GND-1 | — | — | — |
| 7 | Battery constant (terminal 30) | — | — | — | — | — | — | — | — |
| 8 | ECU main power (terminal 87 via main relay) | — | — | — | — | — | — | — | — |
| 9 | DBW output-stage return (P_DKSM-) | — | W4 | — | 0.85 | SP-GND-1 | — | — | — |
OEM-X60002
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | O2 sensor heater, front 1 (pre-cat) | — | W35 | — | 0.5 | G5VOODOOPROV-E-E15 | — | — | — |
| 12 | O2 sensor heater, rear 2 (post-cat) | — | W36 | — | 0.5 | G5VOODOOPROV-E-E22 | — | — | — |
| 14 | O2 sensor signal, rear 2 (post-cat) | — | W43 | — | 0.5 | G5VOODOOPROV-B-B15 | — | — | — |
| 16 | O2 sensor signal, rear 1 (post-cat) | — | W44 | — | 0.5 | G5VOODOOPROV-B-B16 | — | — | — |
| 2 | O2 sensor heater, front 2 (pre-cat) | — | W37 | — | 0.5 | G5VOODOOPROV-A-A18 | — | — | — |
| 23 | Main relay control | — | W33 | — | 0.5 | G5VOODOOPROV-A-A20 | — | — | — |
| 6 | O2 sensor heater, rear 1 (post-cat) | — | W38 | — | 0.5 | G5VOODOOPROV-A-A29 | — | — | — |
OEM-X60003
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Mass air flow (MAF) signal | — | W26 | — | 0.5 | G5VOODOOPROV-A-A17 | — | — | — |
| 10 | VANOS intake solenoid | — | W39 | — | 0.5 | G5VOODOOPROV-A-A28 | — | — | — |
| 11 | Injector cylinder 5 | — | W24 | — | 0.5 | G5VOODOOPROV-B-B4 | — | — | — |
| 12 | Map-controlled thermostat | — | W40 | — | 0.5 | G5VOODOOPROV-A-A27 | — | — | — |
| 13 | Injector cylinder 1 | — | W20 | — | 0.5 | G5VOODOOPROV-A-A4 | — | — | — |
| 15 | Throttle ground | — | — | — | — | — | — | — | — |
| 16 | Oil pressure switch | — | W47 | — | 0.5 | G5VOODOOPROV-A-A31 | — | — | — |
| 21 | Evap purge valve | — | W41 | — | 0.5 | G5VOODOOPROV-A-A26 | — | — | — |
| 22 | Idle speed control, close | — | — | — | — | — | — | — | — |
| 23 | Idle speed control, open | — | — | — | — | — | — | — | — |
| 26 | Injector cylinder 3 | — | W22 | — | 0.5 | G5VOODOOPROV-A-A2 | — | — | — |
| 27 | Intake air temperature (IAT) | — | W45 | — | 0.5 | G5VOODOOPROV-A-A16 | — | — | — |
| 28 | Engine coolant temperature (ECT) | — | W31 | — | 0.5 | G5VOODOOPROV-A-A15 | — | — | — |
| 29 | Intake camshaft position | — | W11 | — | 0.5 | G5VOODOOPROV-A-A30 | — | — | — |
| 3 | Crankshaft position | — | W9 | — | 0.5 | G5VOODOOPROV-A-A8 | — | — | — |
| 30 | Exhaust camshaft position | — | W10 | — | 0.5 | G5VOODOOPROV-A-A9 | — | — | — |
| 31 | Throttle position sensor 2 | — | W29 | — | 0.5 | G5VOODOOPROV-A-A14 | — | — | — |
| 32 | Throttle position sensor 1 | — | W27 | — | 0.5 | G5VOODOOPROV-A-A22 | — | — | — |
| 33 | Knock sensor 1 | — | W12 | — | 0.5 | G5VOODOOPROV-B-B9 | — | — | — |
| 34 | Knock sensor 2 | — | W13 | — | 0.5 | G5VOODOOPROV-B-B8 | — | — | — |
| 35 | ECT ground | — | — | — | — | — | — | — | — |
| 36 | Intake camshaft ground | — | — | — | — | — | — | — | — |
| 37 | Crankshaft ground | — | — | — | — | — | — | — | — |
| 4 | MAF supply | — | — | — | — | — | — | — | — |
| 42 | Throttle motor drive 1 (H-bridge) | — | — | — | — | — | — | — | — |
| 43 | Throttle motor drive 2 (H-bridge) | — | — | — | — | — | — | — | — |
| 44 | Engine oil temperature | — | W46 | — | 0.5 | G5VOODOOPROV-B-B6 | — | — | — |
| 45 | Oil temperature ground | — | — | — | — | — | — | — | — |
| 46 | Knock sensor 3 | — | — | — | — | — | — | — | — |
| 47 | Knock sensor 4 | — | — | — | — | — | — | — | — |
| 49 | Exhaust camshaft ground | — | — | — | — | — | — | — | — |
| 5 | Throttle (EDK/ITB) supply | — | — | — | — | — | — | — | — |
| 50 | Oil level switch | — | W48 | — | 0.5 | G5VOODOOPROV-A-A23 | — | — | — |
| 6 | Injector cylinder 2 | — | W21 | — | 0.5 | G5VOODOOPROV-A-A3 | — | — | — |
| 7 | Injector cylinder 4 | — | W23 | — | 0.5 | G5VOODOOPROV-A-A1 | — | — | — |
| 8 | Injector cylinder 6 | — | W25 | — | 0.5 | G5VOODOOPROV-B-B3 | — | — | — |
| 9 | VANOS exhaust solenoid | — | W42 | — | 0.5 | G5VOODOOPROV-B-B2 | — | — | — |
OEM-X60004
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | Fuel pump relay control | — | W34 | — | 0.5 | G5VOODOOPROV-A-A19 | — | — | — |
| 12 | Pedal ground 2 | — | — | — | — | — | — | — | — |
| 13 | Pedal position signal 2 | — | W30 | — | 0.5 | G5VOODOOPROV-B-B33 | — | — | — |
| 14 | Pedal +5V supply 2 | — | W6 | — | 0.5 | SP-5V1-1 | — | — | — |
| 7 | Pedal ground 1 | — | — | — | — | — | — | — | — |
| 8 | Pedal position signal 1 | — | W28 | — | 0.5 | G5VOODOOPROV-A-A33 | — | — | — |
| 9 | Pedal +5V supply 1 | — | W7 | — | 0.5 | SP-5V1-1 | — | — | — |
OEM-X60005
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Ignition coil 5 | — | W18 | — | 0.5 | G5VOODOOPROV-B-B13 | — | — | — |
| 4 | Ignition coil 3 | — | W16 | — | 0.5 | G5VOODOOPROV-A-A11 | — | — | — |
| 5 | Ignition ground | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 6 | Ignition coil 1 | — | W14 | — | 0.5 | G5VOODOOPROV-A-A13 | — | — | — |
| 7 | Ignition coil 2 | — | W15 | — | 0.5 | G5VOODOOPROV-A-A12 | — | — | — |
| 8 | Ignition coil 4 | — | W17 | — | 0.5 | G5VOODOOPROV-A-A10 | — | — | — |
| 9 | Ignition coil 6 | — | W19 | — | 0.5 | G5VOODOOPROV-B-B12 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W6 | — | 0.5 | OEM-X60004-14 | — | — | — |
| 1 | — | — | W7 | — | 0.5 | OEM-X60004-9 | — | — | — |
| 1 | — | — | W8 | — | 0.5 | G5VOODOOPROV-A-A32 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-X60001-4 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-X60001-5 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | OEM-X60001-6 | — | — | — |
| 1 | — | — | W4 | — | 0.85 | OEM-X60001-9 | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-X60005-5 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-X60001-1 | Injector relay control | low_side_out | G5VOODOOPROV-A-A21 | Aux 1 | low_side_out | corroborated | |
| OEM-X60001-2 | DBW output-stage supply (P_DKSM+) | power_in | — | — | — | single_source | |
| OEM-X60001-4 | Power ground | ground | — | — | — | corroborated | |
| OEM-X60001-5 | Power ground | ground | — | — | — | corroborated | |
| OEM-X60001-6 | Power ground | ground | — | — | — | corroborated | |
| OEM-X60001-7 | Battery constant (terminal 30) | power_in | — | — | — | corroborated | |
| OEM-X60001-8 | ECU main power (terminal 87 via main relay) | power_in | — | — | — | corroborated | |
| OEM-X60001-9 | DBW output-stage return (P_DKSM-) | ground | — | — | — | single_source | |
| OEM-X60002-1 | O2 sensor heater, front 1 (pre-cat) | low_side_out | G5VOODOOPROV-E-E15 | Aux 13 / WB Heater 1 | low_side_out | corroborated | |
| OEM-X60002-12 | O2 sensor heater, rear 2 (post-cat) | low_side_out | G5VOODOOPROV-E-E22 | Aux 14 / WB Heater 2 | low_side_out | corroborated | |
| OEM-X60002-14 | O2 sensor signal, rear 2 (post-cat) | lambda_nb_in | G5VOODOOPROV-B-B15 | Analogue Volt 6 | analog_in | corroborated | |
| OEM-X60002-16 | O2 sensor signal, rear 1 (post-cat) | lambda_nb_in | G5VOODOOPROV-B-B16 | Analogue Volt 7 | analog_in | corroborated | |
| OEM-X60002-2 | O2 sensor heater, front 2 (pre-cat) | low_side_out | G5VOODOOPROV-A-A18 | Aux 4 | low_side_out | corroborated | |
| OEM-X60002-23 | Main relay control | low_side_out | G5VOODOOPROV-A-A20 | Aux 2 | low_side_out | corroborated | |
| OEM-X60002-6 | O2 sensor heater, rear 1 (post-cat) | low_side_out | G5VOODOOPROV-A-A29 | Aux 5 | switch_out | corroborated | |
| OEM-X60003-1 | Mass air flow (MAF) signal | analog_in | G5VOODOOPROV-A-A17 | Analogue Volt 1 | analog_in | corroborated | |
| OEM-X60003-10 | VANOS intake solenoid | low_side_out | G5VOODOOPROV-A-A28 | Aux 6 | switch_out | corroborated | |
| OEM-X60003-11 | Injector cylinder 5 | injector_out | G5VOODOOPROV-B-B4 | Injection 5 | injector_out | corroborated | |
| OEM-X60003-12 | Map-controlled thermostat | low_side_out | G5VOODOOPROV-A-A27 | Aux 7 | switch_out | corroborated | |
| OEM-X60003-13 | Injector cylinder 1 | injector_out | G5VOODOOPROV-A-A4 | Injection 1 | injector_out | corroborated | |
| OEM-X60003-15 | Throttle ground | sensor_ground | — | — | — | corroborated | |
| OEM-X60003-16 | Oil pressure switch | digital_in | G5VOODOOPROV-A-A31 | Digital Input 2 | digital_in | corroborated | |
| OEM-X60003-21 | Evap purge valve | low_side_out | G5VOODOOPROV-A-A26 | Aux 8 | switch_out | corroborated | |
| OEM-X60003-22 | Idle speed control, close | hbridge_out | — | — | — | corroborated | |
| OEM-X60003-23 | Idle speed control, open | hbridge_out | — | — | — | corroborated | |
| OEM-X60003-26 | Injector cylinder 3 | injector_out | G5VOODOOPROV-A-A2 | Injection 3 | injector_out | corroborated | |
| OEM-X60003-27 | Intake air temperature (IAT) | temp_in | G5VOODOOPROV-A-A16 | Analogue Temp 2 | temp_in | corroborated | |
| OEM-X60003-28 | Engine coolant temperature (ECT) | temp_in | G5VOODOOPROV-A-A15 | Analogue Temp 1 | temp_in | corroborated | |
| OEM-X60003-29 | Intake camshaft position | trigger_in | G5VOODOOPROV-A-A30 | Digital Input 1 | digital_in | corroborated | |
| OEM-X60003-3 | Crankshaft position | trigger_in | G5VOODOOPROV-A-A8 | Trigger 1 | trigger_in | corroborated | |
| OEM-X60003-30 | Exhaust camshaft position | trigger_in | G5VOODOOPROV-A-A9 | Trigger 2 | trigger_in | corroborated | |
| OEM-X60003-31 | Throttle position sensor 2 | analog_in | G5VOODOOPROV-A-A14 | Analogue Volt 4 | analog_in | corroborated | |
| OEM-X60003-32 | Throttle position sensor 1 | analog_in | G5VOODOOPROV-A-A22 | Analogue Volt 2 | analog_in | corroborated | |
| OEM-X60003-33 | Knock sensor 1 | knock_in | G5VOODOOPROV-B-B9 | Knock 1 | knock_in | corroborated | |
| OEM-X60003-34 | Knock sensor 2 | knock_in | G5VOODOOPROV-B-B8 | Knock 2 | knock_in | corroborated | |
| OEM-X60003-35 | ECT ground | sensor_ground | — | — | — | corroborated | |
| OEM-X60003-36 | Intake camshaft ground | sensor_ground | — | — | — | corroborated | |
| OEM-X60003-37 | Crankshaft ground | sensor_ground | — | — | — | corroborated | |
| OEM-X60003-4 | MAF supply | power_in | — | — | — | corroborated | |
| OEM-X60003-42 | Throttle motor drive 1 (H-bridge) | hbridge_out | — | — | — | corroborated | |
| OEM-X60003-43 | Throttle motor drive 2 (H-bridge) | hbridge_out | — | — | — | corroborated | |
| OEM-X60003-44 | Engine oil temperature | temp_in | G5VOODOOPROV-B-B6 | Analogue Temp 3 | temp_in | corroborated | |
| OEM-X60003-45 | Oil temperature ground | sensor_ground | — | — | — | corroborated | |
| OEM-X60003-46 | Knock sensor 3 | knock_in | — | — | — | corroborated | |
| OEM-X60003-47 | Knock sensor 4 | knock_in | — | — | — | corroborated | |
| OEM-X60003-49 | Exhaust camshaft ground | sensor_ground | — | — | — | corroborated | |
| OEM-X60003-5 | Throttle (EDK/ITB) supply | power_in | — | — | — | corroborated | |
| OEM-X60003-50 | Oil level switch | digital_in | G5VOODOOPROV-A-A23 | Digital Input 3 | digital_in | corroborated | |
| OEM-X60003-6 | Injector cylinder 2 | injector_out | G5VOODOOPROV-A-A3 | Injection 2 | injector_out | corroborated | |
| OEM-X60003-7 | Injector cylinder 4 | injector_out | G5VOODOOPROV-A-A1 | Injection 4 | injector_out | corroborated | |
| OEM-X60003-8 | Injector cylinder 6 | injector_out | G5VOODOOPROV-B-B3 | Injection 6 | injector_out | corroborated | |
| OEM-X60003-9 | VANOS exhaust solenoid | low_side_out | G5VOODOOPROV-B-B2 | Injection 7 | injector_out | corroborated | |
| OEM-X60004-10 | Fuel pump relay control | low_side_out | G5VOODOOPROV-A-A19 | Aux 3 | low_side_out | corroborated | |
| OEM-X60004-12 | Pedal ground 2 | sensor_ground | — | — | — | corroborated | |
| OEM-X60004-13 | Pedal position signal 2 | analog_in | G5VOODOOPROV-B-B33 | Analogue Volt 5 | analog_in | corroborated | |
| OEM-X60004-14 | Pedal +5V supply 2 | vref | G5VOODOOPROV-A-A32 | +5V Out | vref | corroborated | |
| OEM-X60004-7 | Pedal ground 1 | sensor_ground | — | — | — | corroborated | |
| OEM-X60004-8 | Pedal position signal 1 | analog_in | G5VOODOOPROV-A-A33 | Analogue Volt 3 | analog_in | corroborated | |
| OEM-X60004-9 | Pedal +5V supply 1 | vref | G5VOODOOPROV-A-A32 | +5V Out | vref | corroborated | |
| OEM-X60005-1 | Ignition coil 5 | ignition_out | G5VOODOOPROV-B-B13 | Ignition 5 | ignition_out | corroborated | |
| OEM-X60005-4 | Ignition coil 3 | ignition_out | G5VOODOOPROV-A-A11 | Ignition 3 | ignition_out | corroborated | |
| OEM-X60005-5 | Ignition ground | ground | — | — | — | corroborated | |
| OEM-X60005-6 | Ignition coil 1 | ignition_out | G5VOODOOPROV-A-A13 | Ignition 1 | ignition_out | corroborated | |
| OEM-X60005-7 | Ignition coil 2 | ignition_out | G5VOODOOPROV-A-A12 | Ignition 2 | ignition_out | corroborated | |
| OEM-X60005-8 | Ignition coil 4 | ignition_out | G5VOODOOPROV-A-A10 | Ignition 4 | ignition_out | corroborated | |
| OEM-X60005-9 | Ignition coil 6 | ignition_out | G5VOODOOPROV-B-B12 | Ignition 6 | ignition_out | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-X60001-4 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W2 | OEM-X60001-5 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W3 | OEM-X60001-6 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W4 | OEM-X60001-9 | SP-GND-1 | 0.85 | no route | DBW output-stage return (P_DKSM-) | — | |
| W5 | OEM-X60005-5 | SP-GND-1 | 0.85 | no route | Ignition ground | — | |
| W6 | OEM-X60004-14 | SP-5V1-1 | 0.5 | no route | Pedal +5V supply 2 | — | |
| W7 | OEM-X60004-9 | SP-5V1-1 | 0.5 | no route | Pedal +5V supply 1 | — | |
| W8 | SP-5V1-1 | G5VOODOOPROV-A-A32 | 0.5 | no route | +5V Out | — | |
| W9 | OEM-X60003-3 | G5VOODOOPROV-A-A8 | 0.5 | no route | Crankshaft position | — | |
| W10 | OEM-X60003-30 | G5VOODOOPROV-A-A9 | 0.5 | no route | Exhaust camshaft position | — | |
| W11 | OEM-X60003-29 | G5VOODOOPROV-A-A30 | 0.5 | no route | Intake camshaft position | — | |
| W12 | OEM-X60003-33 | G5VOODOOPROV-B-B9 | 0.5 | no route | Knock sensor 1 | — | |
| W13 | OEM-X60003-34 | G5VOODOOPROV-B-B8 | 0.5 | no route | Knock sensor 2 | — | |
| W14 | OEM-X60005-6 | G5VOODOOPROV-A-A13 | 0.5 | no route | Ignition coil 1 | — | |
| W15 | OEM-X60005-7 | G5VOODOOPROV-A-A12 | 0.5 | no route | Ignition coil 2 | — | |
| W16 | OEM-X60005-4 | G5VOODOOPROV-A-A11 | 0.5 | no route | Ignition coil 3 | — | |
| W17 | OEM-X60005-8 | G5VOODOOPROV-A-A10 | 0.5 | no route | Ignition coil 4 | — | |
| W18 | OEM-X60005-1 | G5VOODOOPROV-B-B13 | 0.5 | no route | Ignition coil 5 | — | |
| W19 | OEM-X60005-9 | G5VOODOOPROV-B-B12 | 0.5 | no route | Ignition coil 6 | — | |
| W20 | OEM-X60003-13 | G5VOODOOPROV-A-A4 | 0.5 | no route | Injector cylinder 1 | — | |
| W21 | OEM-X60003-6 | G5VOODOOPROV-A-A3 | 0.5 | no route | Injector cylinder 2 | — | |
| W22 | OEM-X60003-26 | G5VOODOOPROV-A-A2 | 0.5 | no route | Injector cylinder 3 | — | |
| W23 | OEM-X60003-7 | G5VOODOOPROV-A-A1 | 0.5 | no route | Injector cylinder 4 | — | |
| W24 | OEM-X60003-11 | G5VOODOOPROV-B-B4 | 0.5 | no route | Injector cylinder 5 | — | |
| W25 | OEM-X60003-8 | G5VOODOOPROV-B-B3 | 0.5 | no route | Injector cylinder 6 | — | |
| W26 | OEM-X60003-1 | G5VOODOOPROV-A-A17 | 0.5 | no route | Mass air flow (MAF) signal | — | |
| W27 | OEM-X60003-32 | G5VOODOOPROV-A-A22 | 0.5 | no route | Throttle position sensor 1 | — | |
| W28 | OEM-X60004-8 | G5VOODOOPROV-A-A33 | 0.5 | no route | Pedal position signal 1 | — | |
| W29 | OEM-X60003-31 | G5VOODOOPROV-A-A14 | 0.5 | no route | Throttle position sensor 2 | — | |
| W30 | OEM-X60004-13 | G5VOODOOPROV-B-B33 | 0.5 | no route | Pedal position signal 2 | — | |
| W31 | OEM-X60003-28 | G5VOODOOPROV-A-A15 | 0.5 | no route | Engine coolant temperature (ECT) | — | |
| W32 | OEM-X60001-1 | G5VOODOOPROV-A-A21 | 0.5 | no route | Injector relay control | — | |
| W33 | OEM-X60002-23 | G5VOODOOPROV-A-A20 | 0.5 | no route | Main relay control | — | |
| W34 | OEM-X60004-10 | G5VOODOOPROV-A-A19 | 0.5 | no route | Fuel pump relay control | — | |
| W35 | OEM-X60002-1 | G5VOODOOPROV-E-E15 | 0.5 | no route | O2 sensor heater, front 1 (pre-cat) | — | |
| W36 | OEM-X60002-12 | G5VOODOOPROV-E-E22 | 0.5 | no route | O2 sensor heater, rear 2 (post-cat) | — | |
| W37 | OEM-X60002-2 | G5VOODOOPROV-A-A18 | 0.5 | no route | O2 sensor heater, front 2 (pre-cat) | — | |
| W38 | OEM-X60002-6 | G5VOODOOPROV-A-A29 | 0.5 | no route | O2 sensor heater, rear 1 (post-cat) | — | |
| W39 | OEM-X60003-10 | G5VOODOOPROV-A-A28 | 0.5 | no route | VANOS intake solenoid | — | |
| W40 | OEM-X60003-12 | G5VOODOOPROV-A-A27 | 0.5 | no route | Map-controlled thermostat | — | |
| W41 | OEM-X60003-21 | G5VOODOOPROV-A-A26 | 0.5 | no route | Evap purge valve | — | |
| W42 | OEM-X60003-9 | G5VOODOOPROV-B-B2 | 0.5 | no route | VANOS exhaust solenoid | — | |
| W43 | OEM-X60002-14 | G5VOODOOPROV-B-B15 | 0.5 | no route | O2 sensor signal, rear 2 (post-cat) | — | |
| W44 | OEM-X60002-16 | G5VOODOOPROV-B-B16 | 0.5 | no route | O2 sensor signal, rear 1 (post-cat) | — | |
| W45 | OEM-X60003-27 | G5VOODOOPROV-A-A16 | 0.5 | no route | Intake air temperature (IAT) | — | |
| W46 | OEM-X60003-44 | G5VOODOOPROV-B-B6 | 0.5 | no route | Engine oil temperature | — | |
| W47 | OEM-X60003-16 | G5VOODOOPROV-A-A31 | 0.5 | no route | Oil pressure switch | — | |
| W48 | OEM-X60003-50 | G5VOODOOPROV-A-A23 | 0.5 | no route | Oil level switch | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | BMW-E46-MSS54-CONN | BMW | E46 DME (MSS54) harness connector | 1.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (17)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | PHYS_REQUIRED_OPEN | G5VOODOOPROV-A-A6 | G5VOODOOPROV-A-A6 "Ignition Switch" is required but not wired. |
| error | REQUIRED_UNMAPPED | OEM-X60001-2 | Required OEM function "DBW output-stage supply (P_DKSM+)" (power_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60001-4 | Required OEM function "Power ground" (ground) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60001-5 | Required OEM function "Power ground" (ground) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60001-6 | Required OEM function "Power ground" (ground) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60001-8 | Required OEM function "ECU main power (terminal 87 via main relay)" (power_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60001-9 | Required OEM function "DBW output-stage return (P_DKSM-)" (ground) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60003-42 | Required OEM function "Throttle motor drive 1 (H-bridge)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60003-43 | Required OEM function "Throttle motor drive 2 (H-bridge)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X60005-5 | Required OEM function "Ignition ground" (ground) is not connected to the new ECU. |
| warn | NET_FAMILY | OEM-X60003-29 ↔ G5VOODOOPROV-A-A30 | OEM-X60003-29 "Intake camshaft position" [trigger_in] is wired to G5VOODOOPROV-A-A30 "Digital Input 1" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| info | NET_FAMILY | OEM-X60002-6 ↔ G5VOODOOPROV-A-A29 | OEM-X60002-6 "O2 sensor heater, rear 1 (post-cat)" [low_side_out] is wired to G5VOODOOPROV-A-A29 "Aux 5" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-X60003-10 ↔ G5VOODOOPROV-A-A28 | OEM-X60003-10 "VANOS intake solenoid" [low_side_out] is wired to G5VOODOOPROV-A-A28 "Aux 6" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-X60003-12 ↔ G5VOODOOPROV-A-A27 | OEM-X60003-12 "Map-controlled thermostat" [low_side_out] is wired to G5VOODOOPROV-A-A27 "Aux 7" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-X60003-21 ↔ G5VOODOOPROV-A-A26 | OEM-X60003-21 "Evap purge valve" [low_side_out] is wired to G5VOODOOPROV-A-A26 "Aux 8" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-X60003-9 ↔ G5VOODOOPROV-B-B2 | OEM-X60003-9 "VANOS exhaust solenoid" [low_side_out] is wired to G5VOODOOPROV-B-B2 "Injection 7" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | UNMAPPED | OEM | 14 optional OEM pins are not mapped: OEM-X60003-15 Throttle ground; OEM-X60003-22 Idle speed control, close; OEM-X60003-23 Idle speed control, open; OEM-X60003-35 ECT ground; OEM-X60003-36 Intake camshaft ground; OEM-X60003-37 Crankshaft ground; OEM-X60003-4 MAF supply; OEM-X60003-45 Oil temperature ground; OEM-X60003-46 Knock sensor 3; OEM-X60003-47 Knock sensor 4; OEM-X60003-49 Exhaust camshaft ground; OEM-X60003-5 Throttle (EDK/ITB) supply; OEM-X60004-12 Pedal ground 2; OEM-X60004-7 Pedal ground 1 |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-X60001-7 | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
Notes
Fit check: unconfirmed. Confirm these before building: - Needs CAN (E46 K-bus/CAN); not documented for this ECU - This car has EWS 3.3 (rolling code) immobilizer; needs a delete/bypass Auto-mapped by auto_map() from the library pin data on 2026-10-11. Review every wire against both manuals before building. Open items: - Main-relay feed: no ecu_main_power pin on the stock or the new ECU - Link G5 Voodoo Pro V1: no power-ground pins in the library - Link G5 Voodoo Pro V1: no sensor-ground pin in the library - OEM-X60003 42: Throttle motor drive 1 (H-bridge): no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-X60003 43: Throttle motor drive 2 (H-bridge): no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-X60001 2: DBW output-stage supply (P_DKSM+): no rule for class switched_feed; wire by hand - OEM-X60001 8: ECU main power (terminal 87 via main relay): no rule for class ecu_main_power; wire by hand - G5VOODOOPROV-A A6: Ignition Switch: required by Link G5 Voodoo Pro V1 but no stock pin feeds it; wire by hand Not wired: - OEM-X60001 7: Battery constant (terminal 30): Link G5 Voodoo Pro V1 has no battery-constant input; not needed - OEM-X60003 46: Knock sensor 3: no free knock input on Link G5 Voodoo Pro V1 - OEM-X60003 47: Knock sensor 4: no free knock input on Link G5 Voodoo Pro V1 - OEM-X60004 7: Pedal ground 1: no rule for class ground_sensor; wire by hand - OEM-X60004 12: Pedal ground 2: no rule for class ground_sensor; wire by hand - OEM-X60003 15: Throttle ground: no rule for class ground_sensor; wire by hand - OEM-X60003 22: Idle speed control, close: no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-X60003 23: Idle speed control, open: no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-X60003 35: ECT ground: no rule for class ground_sensor; wire by hand - OEM-X60003 36: Intake camshaft ground: no rule for class ground_sensor; wire by hand - OEM-X60003 37: Crankshaft ground: no rule for class ground_sensor; wire by hand - OEM-X60003 4: MAF supply: no rule for class switched_feed; wire by hand - OEM-X60003 45: Oil temperature ground: no rule for class ground_sensor; wire by hand - OEM-X60003 49: Exhaust camshaft ground: no rule for class ground_sensor; wire by hand - OEM-X60003 5: Throttle (EDK/ITB) supply: no rule for class switched_feed; wire by hand
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | oem_wiring_diagram | BMW WDS A6000 DME pin table, E83 X3 (M54B30/MS45) | https://wds.psjr.org/sv/e83/zinfo/E83_PA6000A.htm | — | — | — |
| 4 | vendor_doc | Link G5 Voodoo Pro V1 Installer I/O Table | https://kb.linkecu.com/__attachments/a_5cf0fc044bcfb915ac75562b29399beb93e47860e38990b3c01614530f927686/G5%20Voodoo%20Pro%20V1%20Installer%20IO%20Table.pdf | — | — | — |
| 2 | community_copy | bimmer-service: DME MSS54 (S54) pinout | https://www.bimmer-service.com/2025/11/14/dme-mss54-s54-pinout-schematic-diagram/ | — | — | — |
| 2 | community_copy | rusefi wiki: 2002 and 2004 BMW M3 E46 DME pinout (S54/MSS54) | https://github.com/rusefi/rusefi/wiki/2002-and-2004-BMW-M3-E46-DME-pinout | — | — | — |