Chevrolet Camaro SS 2010-15 (LS3/L99) → Motorsport Electronics ME360 (auto)
Chevrolet Camaro SS 2010-15 (LS3/L99) — Motorsport Electronics — ME360
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-11
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 8: read the Findings page before cutting any wire |
| Size of the job | 86 wires · 7 connectors · 0 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-X1-19 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-X1-47 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | ME360-C1-15 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | SP-14V-1 | ME360-C1-64 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-X1-73 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-X2-78 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-X2-79 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | SP-GND-1 | ME360-C1-10 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | ME360-C1-61 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | SP-GND-1 | ME360-C1-89 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | SP-GND-1 | ME360-C1-90 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-X1-11 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-X1-13 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-X1-23 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-X1-30 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-X1-31 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-X1-38 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-X1-49 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-X2-22 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-X2-34 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-X2-35 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-X2-52 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-X2-53 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-X2-56 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-X2-60 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-X2-66 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-X2-69 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | SP-0V-1 | ME360-C1-52 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | SP-0V-1 | ME360-C1-84 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-X1-33 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-X1-34 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-X1-36 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-X1-56 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-X2-2 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-X2-3 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-X2-41 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-X2-43 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-X2-44 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | SP-5V1-1 | ME360-C1-45 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-X2-68 | ME360-C1-80 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-X2-64 | ME360-C1-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-X2-26 | ME360-C1-53 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-X2-70 | ME360-C1-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-X2-73 | ME360-C1-31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-X2-77 | ME360-C1-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-X2-76 | ME360-C1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | OEM-X2-75 | ME360-C1-59 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | OEM-X2-74 | ME360-C1-60 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W49 | OEM-X2-20 | ME360-C1-63 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W50 | OEM-X2-37 | ME360-C1-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W51 | OEM-X2-38 | ME360-C1-33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W52 | OEM-X2-39 | ME360-C1-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W53 | OEM-X2-18 | ME360-C1-28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W54 | OEM-X2-19 | ME360-C1-58 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W55 | OEM-X2-40 | ME360-C1-63 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W56 | OEM-X2-17 | ME360-C1-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W57 | OEM-X1-50 | ME360-C1-37 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W58 | OEM-X1-59 | ME360-C1-42 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W59 | OEM-X1-41 | ME360-C1-26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W60 | OEM-X2-58 | ME360-C1-56 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W61 | OEM-X1-29 | ME360-C1-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W62 | OEM-X2-65 | ME360-C1-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W63 | OEM-X2-21 | ME360-C1-86 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W64 | OEM-X1-17 | ME360-C1-72 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W65 | OEM-X1-51 | ME360-C1-43 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W66 | OEM-X1-52 | ME360-C1-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W67 | OEM-X1-58 | ME360-C1-75 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W68 | OEM-X1-63 | ME360-C1-40 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W69 | OEM-X1-64 | ME360-C1-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W70 | OEM-X1-65 | ME360-C1-73 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W71 | OEM-X2-12 | ME360-C1-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W72 | OEM-X2-13 | ME360-C1-74 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W73 | OEM-X2-10 | ME360-C1-44 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W74 | OEM-X2-14 | ME360-C1-69 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W75 | OEM-X2-9 | ME360-C1-39 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W76 | OEM-X2-11 | ME360-C1-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W77 | OEM-X1-48 | ME360-C1-79 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W78 | OEM-X1-37 | ME360-C1-57 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W79 | OEM-X1-71 | ME360-C1-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W80 | OEM-X1-72 | ME360-C1-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W81 | OEM-X1-2 | ME360-C1-8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W82 | OEM-X1-1 | ME360-C1-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W83 | OEM-X1-3 | ME360-C1-62 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W84 | OEM-X1-9 | ME360-C1-34 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W85 | OEM-X1-28 | ME360-C1-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W86 | OEM-X1-27 | ME360-C1-51 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | ME360-C1-15 | ME360-C1-10 | open (OL) | +12 V supply must not touch power ground | |
| 2 | ME360-C1-45 | ME360-C1-10 | open (OL) | 5 V sensor reference must not touch power ground | |
| 3 | ME360-C1-15 | ME360-C1-45 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 4 | ME360-C1-52 | ME360-C1-15 | open (OL) | sensor ground must not touch +12 V supply | |
| 5 | ME360-C1-52 | ME360-C1-45 | open (OL) | sensor ground must not touch 5 V sensor reference |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
ME360-C1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | COIL 4 | — | W46 | — | 0.5 | OEM-X2-76 | — | — | — |
| 10 | GROUND CHASSIS | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 11 | EGT 1 | — | — | — | — | — | — | — | — |
| 12 | LOW SIDE 2 | — | W71 | — | 0.5 | OEM-X2-12 | — | — | — |
| 13 | LOW SIDE RELAY 15 | — | W66 | — | 0.5 | OEM-X1-52 | — | — | — |
| 14 | LSU +12V | — | — | — | — | — | — | — | — |
| 15 | IGN +12V | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 16 | LSU HEATER -VE | — | W69 | — | 0.5 | OEM-X1-64 | — | — | — |
| 17 | ANA VOLT 3 | — | W61 | — | 0.5 | OEM-X1-29 | — | — | — |
| 18 | ANA VOLT 4 | — | W62 | — | 0.5 | OEM-X2-65 | — | — | — |
| 19 | LSU UN | — | — | — | — | — | — | — | — |
| 2 | COIL 3 | — | W45 | — | 0.5 | OEM-X2-77 | — | — | — |
| 20 | LSU VM | — | — | — | — | — | — | — | — |
| 21 | CAN 1 HIGH | — | W85 | — | 0.5 | OEM-X1-28 | — | — | — |
| 22 | CAM A VR+ | — | W41 | — | 0.5 | OEM-X2-64 | — | — | — |
| 23 | CAM A VR- | — | — | — | — | — | — | — | — |
| 24 | SERIAL 1 GROUND | — | — | — | — | — | — | — | — |
| 25 | SERIAL 1 TX | — | — | — | — | — | — | — | — |
| 26 | ANA VOLT 1 | — | W59 | — | 0.5 | OEM-X1-41 | — | — | — |
| 28 | INJECTOR 5 | — | W53 | — | 0.5 | OEM-X2-18 | — | — | — |
| 3 | INJECTOR 4 | — | W52 | — | 0.5 | OEM-X2-39 | — | — | — |
| 31 | COIL 2 | — | W44 | — | 0.5 | OEM-X2-73 | — | — | — |
| 32 | COIL 1 | — | W43 | — | 0.5 | OEM-X2-70 | — | — | — |
| 33 | INJECTOR 3 | — | W51 | — | 0.5 | OEM-X2-38 | — | — | — |
| 34 | DIG_IN 6 | — | W84 | — | 0.5 | OEM-X1-9 | — | — | — |
| 35 | USB D+ | — | — | — | — | — | — | — | — |
| 36 | USB D- | — | — | — | — | — | — | — | — |
| 37 | LOW SIDE RELAY 11 | — | W57 | — | 0.5 | OEM-X1-50 | — | — | — |
| 38 | USB VBUS | — | — | — | — | — | — | — | — |
| 39 | LOW SIDE 6 | — | W75 | — | 0.5 | OEM-X2-9 | — | — | — |
| 4 | INJECTOR 2 | — | W50 | — | 0.5 | OEM-X2-37 | — | — | — |
| 4 | INJECTOR 2 | — | W56 | — | 0.5 | OEM-X2-17 | — | — | — |
| 40 | LOW SIDE RELAY 17 | — | W68 | — | 0.5 | OEM-X1-63 | — | — | — |
| 41 | USB GROUND | — | — | — | — | — | — | — | — |
| 42 | LOW SIDE RELAY 12 | — | W58 | — | 0.5 | OEM-X1-59 | — | — | — |
| 43 | LOW SIDE RELAY 14 | — | W65 | — | 0.5 | OEM-X1-51 | — | — | — |
| 44 | LOW SIDE 4 | — | W73 | — | 0.5 | OEM-X2-10 | — | — | — |
| 45 | 5V REF | — | W39 | — | 0.5 | SP-5V1-1 | — | — | — |
| 46 | 5V REF | — | — | — | — | — | — | — | — |
| 49 | LSU IA | — | — | — | — | — | — | — | — |
| 5 | DIG_IN 4 | — | W82 | — | 0.5 | OEM-X1-1 | — | — | — |
| 50 | LSU IP | — | — | — | — | — | — | — | — |
| 51 | CAN 1 LOW | — | W86 | — | 0.5 | OEM-X1-27 | — | — | — |
| 52 | SENSORS GROUND | — | W28 | — | 0.5 | SP-0V-1 | — | — | — |
| 53 | KNOCK 1 SIGNAL | — | W42 | — | 0.5 | OEM-X2-26 | — | — | — |
| 55 | SERIAL 1 RX | — | — | — | — | — | — | — | — |
| 56 | ANA VOLT 2 | — | W60 | — | 0.5 | OEM-X2-58 | — | — | — |
| 57 | ANA TEMP 2 | — | W78 | — | 0.5 | OEM-X1-37 | — | — | — |
| 58 | INJECTOR 6 | — | W54 | — | 0.5 | OEM-X2-19 | — | — | — |
| 59 | COIL 5 | — | W47 | — | 0.5 | OEM-X2-75 | — | — | — |
| 6 | DIG_IN 1 | — | W79 | — | 0.5 | OEM-X1-71 | — | — | — |
| 60 | COIL 6 | — | W48 | — | 0.5 | OEM-X2-74 | — | — | — |
| 61 | GROUND | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 62 | DIG_IN 5 | — | W83 | — | 0.5 | OEM-X1-3 | — | — | — |
| 63 | INJECTOR 1 | — | W49 | — | 0.5 | OEM-X2-20 | — | — | — |
| 63 | INJECTOR 1 | — | W55 | — | 0.5 | OEM-X2-40 | — | — | — |
| 64 | VBAT | — | W4 | — | 0.85 | SP-14V-1 | — | — | — |
| 65 | H-BRIDGE A OUT 1 | — | — | — | — | — | — | — | — |
| 66 | H-BRIDGE A OUT 2 | — | — | — | — | — | — | — | — |
| 67 | Stepper 1 / A1 | — | — | — | — | — | — | — | — |
| 68 | Stepper 2 / A2 | — | — | — | — | — | — | — | — |
| 69 | LOW SIDE 5 | — | W74 | — | 0.5 | OEM-X2-14 | — | — | — |
| 7 | DIG_IN 2 | — | W80 | — | 0.5 | OEM-X1-72 | — | — | — |
| 70 | Stepper 3 / B1 | — | — | — | — | — | — | — | — |
| 71 | Stepper 4 / B2 | — | — | — | — | — | — | — | — |
| 72 | LOW SIDE RELAY 13 | — | W64 | — | 0.5 | OEM-X1-17 | — | — | — |
| 73 | LOW SIDE 1 | — | W70 | — | 0.5 | OEM-X1-65 | — | — | — |
| 74 | LOW SIDE 3 | — | W72 | — | 0.5 | OEM-X2-13 | — | — | — |
| 75 | LOW SIDE RELAY 16 | — | W67 | — | 0.5 | OEM-X1-58 | — | — | — |
| 76 | 5V REF | — | — | — | — | — | — | — | — |
| 77 | ANA TEMP 3 | — | — | — | — | — | — | — | — |
| 79 | TACHOMETER | — | W77 | — | 0.5 | OEM-X1-48 | — | — | — |
| 8 | DIG_IN 3 | — | W81 | — | 0.5 | OEM-X1-2 | — | — | — |
| 80 | CRANK VR+ | — | W40 | — | 0.5 | OEM-X2-68 | — | — | — |
| 81 | CRANK VR- | — | — | — | — | — | — | — | — |
| 82 | CAM B VR+ | — | — | — | — | — | — | — | — |
| 83 | CAM B VR- | — | — | — | — | — | — | — | — |
| 84 | Sensor Ground | — | W29 | — | 0.5 | SP-0V-1 | — | — | — |
| 86 | ANA TEMP 1 | — | W63 | — | 0.5 | OEM-X2-21 | — | — | — |
| 89 | GROUND | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 9 | LOW SIDE RELAY 18 | — | W76 | — | 0.5 | OEM-X2-11 | — | — | — |
| 90 | GROUND | — | W11 | — | 0.85 | SP-GND-1 | — | — | — |
OEM-X1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Park/Neutral signal (1786) | — | W82 | — | 0.5 | ME360-C1-5 | — | — | — |
| 10 | HO2S signal, bank 1 sensor 2 (post-cat) | — | — | — | — | — | — | — | — |
| 11 | HO2S low reference, bank 1 sensor 2 | — | W12 | — | 0.5 | SP-0V-1 | — | — | — |
| 12 | A/C refrigerant pressure signal | — | — | — | — | — | — | — | — |
| 13 | A/C refrigerant pressure sensor low reference (5514) | — | W13 | — | 0.5 | SP-0V-1 | — | — | — |
| 16 | Fuel level sensor signal, primary (1589) | — | — | — | — | — | — | — | — |
| 17 | High speed cooling fan relay | — | W64 | — | 0.5 | ME360-C1-72 | — | — | — |
| 18 | Accessory wakeup serial data (5985) | — | — | — | — | — | — | — | — |
| 19 | Ignition 1 voltage (key hot) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 2 | 4WD low signal (1694) | — | W81 | — | 0.5 | ME360-C1-8 | — | — | — |
| 20 | Battery positive voltage (batt hot) | — | — | — | — | — | — | — | — |
| 23 | APP sensor low reference | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 24 | Fuel tank pressure signal | — | — | — | — | — | — | — | — |
| 27 | High-speed GMLAN serial data bus - (2501) | — | W86 | — | 0.5 | ME360-C1-51 | — | — | — |
| 28 | High-speed GMLAN serial data bus + (2500) | — | W85 | — | 0.5 | ME360-C1-21 | — | — | — |
| 29 | Accelerator pedal position (APP) sensor 1 signal | — | W61 | — | 0.5 | ME360-C1-17 | — | — | — |
| 3 | Axle switch signal (1695) | — | W83 | — | 0.5 | ME360-C1-62 | — | — | — |
| 30 | APP sensor low reference | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 31 | Fuel tank pressure sensor low reference (6049) | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 32 | Accelerator pedal position (APP) sensor 2 signal | — | — | — | — | — | — | — | — |
| 33 | 5V reference (fuel tank pressure) | — | W30 | — | 0.5 | SP-5V1-1 | — | — | — |
| 34 | 5V reference (A/C pressure) | — | W31 | — | 0.5 | SP-5V1-1 | — | — | — |
| 36 | 5V reference (APP sensor) | — | W32 | — | 0.5 | SP-5V1-1 | — | — | — |
| 37 | Intake air temperature (IAT) signal | — | W78 | — | 0.5 | ME360-C1-57 | — | — | — |
| 38 | Intake air temperature (IAT) low reference | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 41 | Mass air flow (MAF) signal | — | W59 | — | 0.5 | ME360-C1-26 | — | — | — |
| 47 | Ignition 1 voltage (key hot) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 48 | Tachometer output | — | W77 | — | 0.5 | ME360-C1-79 | — | — | — |
| 49 | HO2S low reference, bank 2 sensor 2 | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 50 | Fuel pump relay control (primary) | — | W57 | — | 0.5 | ME360-C1-37 | — | — | — |
| 51 | Fuel pump relay control (secondary) | — | W65 | — | 0.5 | ME360-C1-43 | — | — | — |
| 52 | Starter enable relay control | — | W66 | — | 0.5 | ME360-C1-13 | — | — | — |
| 56 | 5V reference (APP sensor) | — | W33 | — | 0.5 | SP-5V1-1 | — | — | — |
| 57 | VSS output to ABS (128k) | — | — | — | — | — | — | — | — |
| 58 | Low speed cooling fan relay | — | W67 | — | 0.5 | ME360-C1-75 | — | — | — |
| 59 | Powertrain relay coil control (main relay) | — | W58 | — | 0.5 | ME360-C1-42 | — | — | — |
| 61 | EVAP canister vent solenoid | — | — | — | — | — | — | — | — |
| 63 | A/C compressor clutch relay | — | W68 | — | 0.5 | ME360-C1-40 | — | — | — |
| 64 | HO2S heater low control, bank 2 sensor 2 | — | W69 | — | 0.5 | ME360-C1-16 | — | — | — |
| 65 | HO2S heater low control, bank 1 sensor 2 | — | W70 | — | 0.5 | ME360-C1-73 | — | — | — |
| 68 | Malfunction indicator lamp (MIL) | — | — | — | — | — | — | — | — |
| 69 | HO2S signal, bank 2 sensor 2 (post-cat) | — | — | — | — | — | — | — | — |
| 70 | Secondary fuel level sensor signal (1937) | — | — | — | — | — | — | — | — |
| 71 | VSS high signal (manual trans) | — | W79 | — | 0.5 | ME360-C1-6 | — | — | — |
| 72 | VSS low signal (manual trans) | — | W80 | — | 0.5 | ME360-C1-7 | — | — | — |
| 73 | Power ground | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 9 | Brake switch signal | — | W84 | — | 0.5 | ME360-C1-34 | — | — | — |
OEM-X2
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | Cylinder shutoff solenoid 1 (AFM) | — | W73 | — | 0.5 | ME360-C1-44 | — | — | — |
| 11 | Cylinder shutoff solenoid 4 (AFM) | — | W76 | — | 0.5 | ME360-C1-9 | — | — | — |
| 12 | HO2S heater low control, bank 1 sensor 1 | — | W71 | — | 0.5 | ME360-C1-12 | — | — | — |
| 13 | HO2S heater low control, bank 2 sensor 1 | — | W72 | — | 0.5 | ME360-C1-74 | — | — | — |
| 14 | Cylinder shutoff solenoid 2 (AFM) | — | W74 | — | 0.5 | ME360-C1-69 | — | — | — |
| 16 | Camshaft actuator solenoid (VVT) | — | — | — | — | — | — | — | — |
| 17 | Injector 8 | — | W56 | — | 0.5 | ME360-C1-4 | — | — | — |
| 18 | Injector 5 | — | W53 | — | 0.5 | ME360-C1-28 | — | — | — |
| 19 | Injector 6 | — | W54 | — | 0.5 | ME360-C1-58 | — | — | — |
| 2 | 5V reference (crankshaft sensor) | — | W34 | — | 0.5 | SP-5V1-1 | — | — | — |
| 20 | Injector 1 | — | W49 | — | 0.5 | ME360-C1-63 | — | — | — |
| 21 | Engine coolant temperature (ECT) signal | — | W63 | — | 0.5 | ME360-C1-86 | — | — | — |
| 22 | ECT low reference | — | W19 | — | 0.5 | SP-0V-1 | — | — | — |
| 26 | Knock sensor 1 signal A | — | W42 | — | 0.5 | ME360-C1-53 | — | — | — |
| 27 | Knock sensor 1 signal B | — | — | — | — | — | — | — | — |
| 29 | Knock sensor 2 signal A | — | — | — | — | — | — | — | — |
| 3 | 5V reference (throttle body) | — | W35 | — | 0.5 | SP-5V1-1 | — | — | — |
| 30 | Knock sensor 2 signal B | — | — | — | — | — | — | — | — |
| 32 | Generator field duty control | — | — | — | — | — | — | — | — |
| 33 | Oil level switch signal | — | — | — | — | — | — | — | — |
| 34 | Oil pressure low reference | — | W20 | — | 0.5 | SP-0V-1 | — | — | — |
| 35 | Throttle body low reference | — | W21 | — | 0.5 | SP-0V-1 | — | — | — |
| 37 | Injector 2 | — | W50 | — | 0.5 | ME360-C1-4 | — | — | — |
| 38 | Injector 3 | — | W51 | — | 0.5 | ME360-C1-33 | — | — | — |
| 39 | Injector 4 | — | W52 | — | 0.5 | ME360-C1-3 | — | — | — |
| 40 | Injector 7 | — | W55 | — | 0.5 | ME360-C1-63 | — | — | — |
| 41 | 5V reference (oil pressure) | — | W36 | — | 0.5 | SP-5V1-1 | — | — | — |
| 43 | 5V reference (MAP) | — | W37 | — | 0.5 | SP-5V1-1 | — | — | — |
| 44 | 5V reference (camshaft sensor) | — | W38 | — | 0.5 | SP-5V1-1 | — | — | — |
| 5 | Throttle actuator motor control 2 | — | — | — | — | — | — | — | — |
| 50 | Engine oil pressure signal | — | — | — | — | — | — | — | — |
| 52 | Camshaft actuator low reference | — | W22 | — | 0.5 | SP-0V-1 | — | — | — |
| 53 | MAP low reference | — | W23 | — | 0.5 | SP-0V-1 | — | — | — |
| 56 | HO2S low reference, bank 1 sensor 1 | — | W24 | — | 0.5 | SP-0V-1 | — | — | — |
| 57 | HO2S signal, bank 1 sensor 1 (pre-cat) | — | — | — | — | — | — | — | — |
| 58 | Manifold absolute pressure (MAP) signal | — | W60 | — | 0.5 | ME360-C1-56 | — | — | — |
| 59 | HO2S signal, bank 2 sensor 1 (pre-cat) | — | — | — | — | — | — | — | — |
| 6 | Throttle actuator motor control 1 | — | — | — | — | — | — | — | — |
| 60 | HO2S low reference, bank 2 sensor 1 | — | W25 | — | 0.5 | SP-0V-1 | — | — | — |
| 61 | Charge indicator signal | — | — | — | — | — | — | — | — |
| 63 | Throttle position sensor 2 signal | — | — | — | — | — | — | — | — |
| 64 | Camshaft position signal (4x) | — | W41 | — | 0.5 | ME360-C1-22 | — | — | — |
| 65 | Throttle position sensor 1 signal | — | W62 | — | 0.5 | ME360-C1-18 | — | — | — |
| 66 | Camshaft position low reference | — | W26 | — | 0.5 | SP-0V-1 | — | — | — |
| 68 | Crankshaft position signal (58x) | — | W40 | — | 0.5 | ME360-C1-80 | — | — | — |
| 69 | Crankshaft position low reference | — | W27 | — | 0.5 | SP-0V-1 | — | — | — |
| 70 | Ignition coil 1 control | — | W43 | — | 0.5 | ME360-C1-32 | — | — | — |
| 71 | Ignition coil 8 control | — | — | — | — | — | — | — | — |
| 72 | Ignition coil 7 control | — | — | — | — | — | — | — | — |
| 73 | Ignition coil 2 control | — | W44 | — | 0.5 | ME360-C1-31 | — | — | — |
| 74 | Ignition coil 6 control | — | W48 | — | 0.5 | ME360-C1-60 | — | — | — |
| 75 | Ignition coil 5 control | — | W47 | — | 0.5 | ME360-C1-59 | — | — | — |
| 76 | Ignition coil 4 control | — | W46 | — | 0.5 | ME360-C1-1 | — | — | — |
| 77 | Ignition coil 3 control | — | W45 | — | 0.5 | ME360-C1-2 | — | — | — |
| 78 | Coil low reference (odd bank) | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 79 | Coil low reference (even bank) | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 8 | EVAP canister purge solenoid | — | — | — | — | — | — | — | — |
| 9 | Cylinder shutoff solenoid 3 (AFM) | — | W75 | — | 0.5 | ME360-C1-39 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W12 | — | 0.5 | OEM-X1-11 | — | — | — |
| 1 | — | — | W13 | — | 0.5 | OEM-X1-13 | — | — | — |
| 1 | — | — | W14 | — | 0.5 | OEM-X1-23 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | OEM-X1-30 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-X1-31 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | OEM-X1-38 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | OEM-X1-49 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | OEM-X2-22 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | OEM-X2-34 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | OEM-X2-35 | — | — | — |
| 1 | — | — | W22 | — | 0.5 | OEM-X2-52 | — | — | — |
| 1 | — | — | W23 | — | 0.5 | OEM-X2-53 | — | — | — |
| 1 | — | — | W24 | — | 0.5 | OEM-X2-56 | — | — | — |
| 1 | — | — | W25 | — | 0.5 | OEM-X2-60 | — | — | — |
| 1 | — | — | W26 | — | 0.5 | OEM-X2-66 | — | — | — |
| 1 | — | — | W27 | — | 0.5 | OEM-X2-69 | — | — | — |
| 1 | — | — | W28 | — | 0.5 | ME360-C1-52 | — | — | — |
| 1 | — | — | W29 | — | 0.5 | ME360-C1-84 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-X1-19 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-X1-47 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | ME360-C1-15 | — | — | — |
| 1 | — | — | W4 | — | 0.85 | ME360-C1-64 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W30 | — | 0.5 | OEM-X1-33 | — | — | — |
| 1 | — | — | W31 | — | 0.5 | OEM-X1-34 | — | — | — |
| 1 | — | — | W32 | — | 0.5 | OEM-X1-36 | — | — | — |
| 1 | — | — | W33 | — | 0.5 | OEM-X1-56 | — | — | — |
| 1 | — | — | W34 | — | 0.5 | OEM-X2-2 | — | — | — |
| 1 | — | — | W35 | — | 0.5 | OEM-X2-3 | — | — | — |
| 1 | — | — | W36 | — | 0.5 | OEM-X2-41 | — | — | — |
| 1 | — | — | W37 | — | 0.5 | OEM-X2-43 | — | — | — |
| 1 | — | — | W38 | — | 0.5 | OEM-X2-44 | — | — | — |
| 1 | — | — | W39 | — | 0.5 | ME360-C1-45 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W5 | — | 0.85 | OEM-X1-73 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-X2-78 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-X2-79 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | ME360-C1-10 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | ME360-C1-61 | — | — | — |
| 1 | — | — | W10 | — | 0.85 | ME360-C1-89 | — | — | — |
| 1 | — | — | W11 | — | 0.85 | ME360-C1-90 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-X1-1 | Park/Neutral signal (1786) | digital_in | ME360-C1-5 | DIG_IN 4 | digital_in | single_source | |
| OEM-X1-10 | HO2S signal, bank 1 sensor 2 (post-cat) | lambda_nb_in | — | — | — | single_source | |
| OEM-X1-11 | HO2S low reference, bank 1 sensor 2 | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X1-12 | A/C refrigerant pressure signal | analog_in | — | — | — | corroborated | |
| OEM-X1-13 | A/C refrigerant pressure sensor low reference (5514) | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X1-16 | Fuel level sensor signal, primary (1589) | analog_in | — | — | — | single_source | |
| OEM-X1-17 | High speed cooling fan relay | low_side_out | ME360-C1-72 | LOW SIDE RELAY 13 | low_side_out | corroborated | |
| OEM-X1-18 | Accessory wakeup serial data (5985) | serial | — | — | — | single_source | |
| OEM-X1-19 | Ignition 1 voltage (key hot) | power_in | ME360-C1-15 + ME360-C1-64 | IGN +12V + VBAT | power_in | single_source | |
| OEM-X1-2 | 4WD low signal (1694) | digital_in | ME360-C1-8 | DIG_IN 3 | digital_in | single_source | |
| OEM-X1-20 | Battery positive voltage (batt hot) | power_in | — | — | — | single_source | |
| OEM-X1-23 | APP sensor low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X1-24 | Fuel tank pressure signal | analog_in | — | — | — | corroborated | |
| OEM-X1-27 | High-speed GMLAN serial data bus - (2501) | can_l | ME360-C1-51 | CAN 1 LOW | can_l | single_source | |
| OEM-X1-28 | High-speed GMLAN serial data bus + (2500) | can_h | ME360-C1-21 | CAN 1 HIGH | can_h | single_source | |
| OEM-X1-29 | Accelerator pedal position (APP) sensor 1 signal | analog_in | ME360-C1-17 | ANA VOLT 3 | analog_in | single_source | |
| OEM-X1-3 | Axle switch signal (1695) | digital_in | ME360-C1-62 | DIG_IN 5 | digital_in | single_source | |
| OEM-X1-30 | APP sensor low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X1-31 | Fuel tank pressure sensor low reference (6049) | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X1-32 | Accelerator pedal position (APP) sensor 2 signal | analog_in | — | — | — | single_source | |
| OEM-X1-33 | 5V reference (fuel tank pressure) | vref | ME360-C1-45 | 5V REF | vref | single_source | |
| OEM-X1-34 | 5V reference (A/C pressure) | vref | ME360-C1-45 | 5V REF | vref | single_source | |
| OEM-X1-36 | 5V reference (APP sensor) | vref | ME360-C1-45 | 5V REF | vref | single_source | |
| OEM-X1-37 | Intake air temperature (IAT) signal | temp_in | ME360-C1-57 | ANA TEMP 2 | temp_in | corroborated | |
| OEM-X1-38 | Intake air temperature (IAT) low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X1-41 | Mass air flow (MAF) signal | analog_in | ME360-C1-26 | ANA VOLT 1 | analog_in | corroborated | |
| OEM-X1-47 | Ignition 1 voltage (key hot) | power_in | ME360-C1-15 + ME360-C1-64 | IGN +12V + VBAT | power_in | single_source | |
| OEM-X1-48 | Tachometer output | tacho_out | ME360-C1-79 | TACHOMETER | tacho_out | corroborated | |
| OEM-X1-49 | HO2S low reference, bank 2 sensor 2 | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X1-50 | Fuel pump relay control (primary) | low_side_out | ME360-C1-37 | LOW SIDE RELAY 11 | low_side_out | corroborated | |
| OEM-X1-51 | Fuel pump relay control (secondary) | low_side_out | ME360-C1-43 | LOW SIDE RELAY 14 | low_side_out | corroborated | |
| OEM-X1-52 | Starter enable relay control | low_side_out | ME360-C1-13 | LOW SIDE RELAY 15 | low_side_out | corroborated | |
| OEM-X1-56 | 5V reference (APP sensor) | vref | ME360-C1-45 | 5V REF | vref | single_source | |
| OEM-X1-57 | VSS output to ABS (128k) | tacho_out | — | — | — | corroborated | |
| OEM-X1-58 | Low speed cooling fan relay | low_side_out | ME360-C1-75 | LOW SIDE RELAY 16 | low_side_out | corroborated | |
| OEM-X1-59 | Powertrain relay coil control (main relay) | low_side_out | ME360-C1-42 | LOW SIDE RELAY 12 | low_side_out | corroborated | |
| OEM-X1-61 | EVAP canister vent solenoid | low_side_out | — | — | — | corroborated | |
| OEM-X1-63 | A/C compressor clutch relay | low_side_out | ME360-C1-40 | LOW SIDE RELAY 17 | low_side_out | corroborated | |
| OEM-X1-64 | HO2S heater low control, bank 2 sensor 2 | low_side_out | ME360-C1-16 | LSU HEATER -VE | low_side_out | single_source | |
| OEM-X1-65 | HO2S heater low control, bank 1 sensor 2 | low_side_out | ME360-C1-73 | LOW SIDE 1 | low_side_out | single_source | |
| OEM-X1-68 | Malfunction indicator lamp (MIL) | low_side_out | — | — | — | corroborated | |
| OEM-X1-69 | HO2S signal, bank 2 sensor 2 (post-cat) | lambda_nb_in | — | — | — | single_source | |
| OEM-X1-70 | Secondary fuel level sensor signal (1937) | analog_in | — | — | — | single_source | |
| OEM-X1-71 | VSS high signal (manual trans) | digital_in | ME360-C1-6 | DIG_IN 1 | digital_in | corroborated | |
| OEM-X1-72 | VSS low signal (manual trans) | digital_in | ME360-C1-7 | DIG_IN 2 | digital_in | corroborated | |
| OEM-X1-73 | Power ground | ground | ME360-C1-10 + ME360-C1-61 + ME360-C1-89 + ME360-C1-90 | GROUND CHASSIS + GROUND + GROUND + GROUND | ground | single_source | |
| OEM-X1-9 | Brake switch signal | digital_in | ME360-C1-34 | DIG_IN 6 | digital_in | corroborated | |
| OEM-X2-10 | Cylinder shutoff solenoid 1 (AFM) | low_side_out | ME360-C1-44 | LOW SIDE 4 | low_side_out | corroborated | |
| OEM-X2-11 | Cylinder shutoff solenoid 4 (AFM) | low_side_out | ME360-C1-9 | LOW SIDE RELAY 18 | low_side_out | corroborated | |
| OEM-X2-12 | HO2S heater low control, bank 1 sensor 1 | low_side_out | ME360-C1-12 | LOW SIDE 2 | low_side_out | single_source | |
| OEM-X2-13 | HO2S heater low control, bank 2 sensor 1 | low_side_out | ME360-C1-74 | LOW SIDE 3 | low_side_out | single_source | |
| OEM-X2-14 | Cylinder shutoff solenoid 2 (AFM) | low_side_out | ME360-C1-69 | LOW SIDE 5 | low_side_out | corroborated | |
| OEM-X2-16 | Camshaft actuator solenoid (VVT) | low_side_out | — | — | — | corroborated | |
| OEM-X2-17 | Injector 8 | injector_out | ME360-C1-4 | INJECTOR 2 | injector_out | single_source | |
| OEM-X2-18 | Injector 5 | injector_out | ME360-C1-28 | INJECTOR 5 | injector_out | single_source | |
| OEM-X2-19 | Injector 6 | injector_out | ME360-C1-58 | INJECTOR 6 | injector_out | single_source | |
| OEM-X2-2 | 5V reference (crankshaft sensor) | vref | ME360-C1-45 | 5V REF | vref | single_source | |
| OEM-X2-20 | Injector 1 | injector_out | ME360-C1-63 | INJECTOR 1 | injector_out | single_source | |
| OEM-X2-21 | Engine coolant temperature (ECT) signal | temp_in | ME360-C1-86 | ANA TEMP 1 | temp_in | corroborated | |
| OEM-X2-22 | ECT low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X2-26 | Knock sensor 1 signal A | knock_in | ME360-C1-53 | KNOCK 1 SIGNAL | knock_in | corroborated | |
| OEM-X2-27 | Knock sensor 1 signal B | knock_in | — | — | — | single_source | |
| OEM-X2-29 | Knock sensor 2 signal A | knock_in | — | — | — | corroborated | |
| OEM-X2-3 | 5V reference (throttle body) | vref | ME360-C1-45 | 5V REF | vref | single_source | |
| OEM-X2-30 | Knock sensor 2 signal B | knock_in | — | — | — | single_source | |
| OEM-X2-32 | Generator field duty control | low_side_out | — | — | — | corroborated | |
| OEM-X2-33 | Oil level switch signal | digital_in | — | — | — | corroborated | |
| OEM-X2-34 | Oil pressure low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X2-35 | Throttle body low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X2-37 | Injector 2 | injector_out | ME360-C1-4 | INJECTOR 2 | injector_out | single_source | |
| OEM-X2-38 | Injector 3 | injector_out | ME360-C1-33 | INJECTOR 3 | injector_out | single_source | |
| OEM-X2-39 | Injector 4 | injector_out | ME360-C1-3 | INJECTOR 4 | injector_out | single_source | |
| OEM-X2-40 | Injector 7 | injector_out | ME360-C1-63 | INJECTOR 1 | injector_out | single_source | |
| OEM-X2-41 | 5V reference (oil pressure) | vref | ME360-C1-45 | 5V REF | vref | single_source | |
| OEM-X2-43 | 5V reference (MAP) | vref | ME360-C1-45 | 5V REF | vref | single_source | |
| OEM-X2-44 | 5V reference (camshaft sensor) | vref | ME360-C1-45 | 5V REF | vref | single_source | |
| OEM-X2-5 | Throttle actuator motor control 2 | hbridge_out | — | — | — | corroborated | |
| OEM-X2-50 | Engine oil pressure signal | analog_in | — | — | — | corroborated | |
| OEM-X2-52 | Camshaft actuator low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X2-53 | MAP low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X2-56 | HO2S low reference, bank 1 sensor 1 | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X2-57 | HO2S signal, bank 1 sensor 1 (pre-cat) | lambda_nb_in | — | — | — | single_source | |
| OEM-X2-58 | Manifold absolute pressure (MAP) signal | analog_in | ME360-C1-56 | ANA VOLT 2 | analog_in | corroborated | |
| OEM-X2-59 | HO2S signal, bank 2 sensor 1 (pre-cat) | lambda_nb_in | — | — | — | single_source | |
| OEM-X2-6 | Throttle actuator motor control 1 | hbridge_out | — | — | — | corroborated | |
| OEM-X2-60 | HO2S low reference, bank 2 sensor 1 | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X2-61 | Charge indicator signal | low_side_out | — | — | — | corroborated | |
| OEM-X2-63 | Throttle position sensor 2 signal | analog_in | — | — | — | single_source | |
| OEM-X2-64 | Camshaft position signal (4x) | trigger_in | ME360-C1-22 | CAM A VR+ | trigger_in | single_source | |
| OEM-X2-65 | Throttle position sensor 1 signal | analog_in | ME360-C1-18 | ANA VOLT 4 | analog_in | single_source | |
| OEM-X2-66 | Camshaft position low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X2-68 | Crankshaft position signal (58x) | trigger_in | ME360-C1-80 | CRANK VR+ | trigger_in | single_source | |
| OEM-X2-69 | Crankshaft position low reference | sensor_ground | ME360-C1-52 + ME360-C1-84 | SENSORS GROUND + Sensor Ground | sensor_ground | single_source | |
| OEM-X2-70 | Ignition coil 1 control | ignition_out | ME360-C1-32 | COIL 1 | ignition_out | single_source | |
| OEM-X2-71 | Ignition coil 8 control | ignition_out | — | — | — | single_source | |
| OEM-X2-72 | Ignition coil 7 control | ignition_out | — | — | — | single_source | |
| OEM-X2-73 | Ignition coil 2 control | ignition_out | ME360-C1-31 | COIL 2 | ignition_out | single_source | |
| OEM-X2-74 | Ignition coil 6 control | ignition_out | ME360-C1-60 | COIL 6 | ignition_out | single_source | |
| OEM-X2-75 | Ignition coil 5 control | ignition_out | ME360-C1-59 | COIL 5 | ignition_out | single_source | |
| OEM-X2-76 | Ignition coil 4 control | ignition_out | ME360-C1-1 | COIL 4 | ignition_out | single_source | |
| OEM-X2-77 | Ignition coil 3 control | ignition_out | ME360-C1-2 | COIL 3 | ignition_out | single_source | |
| OEM-X2-78 | Coil low reference (odd bank) | ground | ME360-C1-10 + ME360-C1-61 + ME360-C1-89 + ME360-C1-90 | GROUND CHASSIS + GROUND + GROUND + GROUND | ground | single_source | |
| OEM-X2-79 | Coil low reference (even bank) | ground | ME360-C1-10 + ME360-C1-61 + ME360-C1-89 + ME360-C1-90 | GROUND CHASSIS + GROUND + GROUND + GROUND | ground | single_source | |
| OEM-X2-8 | EVAP canister purge solenoid | low_side_out | — | — | — | corroborated | |
| OEM-X2-9 | Cylinder shutoff solenoid 3 (AFM) | low_side_out | ME360-C1-39 | LOW SIDE 6 | low_side_out | corroborated |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-X1-19 | SP-14V-1 | 0.85 | no route | Ignition 1 voltage (key hot) | — | |
| W2 | OEM-X1-47 | SP-14V-1 | 0.85 | no route | Ignition 1 voltage (key hot) | — | |
| W3 | SP-14V-1 | ME360-C1-15 | 0.85 | no route | IGN +12V | — | |
| W4 | SP-14V-1 | ME360-C1-64 | 0.85 | no route | VBAT | — | |
| W5 | OEM-X1-73 | SP-GND-1 | 0.85 | no route | Power ground | — | |
| W6 | OEM-X2-78 | SP-GND-1 | 0.85 | no route | Coil low reference (odd bank) | — | |
| W7 | OEM-X2-79 | SP-GND-1 | 0.85 | no route | Coil low reference (even bank) | — | |
| W8 | SP-GND-1 | ME360-C1-10 | 0.85 | no route | GROUND CHASSIS | — | |
| W9 | SP-GND-1 | ME360-C1-61 | 0.85 | no route | GROUND | — | |
| W10 | SP-GND-1 | ME360-C1-89 | 0.85 | no route | GROUND | — | |
| W11 | SP-GND-1 | ME360-C1-90 | 0.85 | no route | GROUND | — | |
| W12 | OEM-X1-11 | SP-0V-1 | 0.5 | no route | HO2S low reference, bank 1 sensor 2 | — | |
| W13 | OEM-X1-13 | SP-0V-1 | 0.5 | no route | A/C refrigerant pressure sensor low reference (5514) | — | |
| W14 | OEM-X1-23 | SP-0V-1 | 0.5 | no route | APP sensor low reference | — | |
| W15 | OEM-X1-30 | SP-0V-1 | 0.5 | no route | APP sensor low reference | — | |
| W16 | OEM-X1-31 | SP-0V-1 | 0.5 | no route | Fuel tank pressure sensor low reference (6049) | — | |
| W17 | OEM-X1-38 | SP-0V-1 | 0.5 | no route | Intake air temperature (IAT) low reference | — | |
| W18 | OEM-X1-49 | SP-0V-1 | 0.5 | no route | HO2S low reference, bank 2 sensor 2 | — | |
| W19 | OEM-X2-22 | SP-0V-1 | 0.5 | no route | ECT low reference | — | |
| W20 | OEM-X2-34 | SP-0V-1 | 0.5 | no route | Oil pressure low reference | — | |
| W21 | OEM-X2-35 | SP-0V-1 | 0.5 | no route | Throttle body low reference | — | |
| W22 | OEM-X2-52 | SP-0V-1 | 0.5 | no route | Camshaft actuator low reference | — | |
| W23 | OEM-X2-53 | SP-0V-1 | 0.5 | no route | MAP low reference | — | |
| W24 | OEM-X2-56 | SP-0V-1 | 0.5 | no route | HO2S low reference, bank 1 sensor 1 | — | |
| W25 | OEM-X2-60 | SP-0V-1 | 0.5 | no route | HO2S low reference, bank 2 sensor 1 | — | |
| W26 | OEM-X2-66 | SP-0V-1 | 0.5 | no route | Camshaft position low reference | — | |
| W27 | OEM-X2-69 | SP-0V-1 | 0.5 | no route | Crankshaft position low reference | — | |
| W28 | SP-0V-1 | ME360-C1-52 | 0.5 | no route | SENSORS GROUND | — | |
| W29 | SP-0V-1 | ME360-C1-84 | 0.5 | no route | Sensor Ground | — | |
| W30 | OEM-X1-33 | SP-5V1-1 | 0.5 | no route | 5V reference (fuel tank pressure) | — | |
| W31 | OEM-X1-34 | SP-5V1-1 | 0.5 | no route | 5V reference (A/C pressure) | — | |
| W32 | OEM-X1-36 | SP-5V1-1 | 0.5 | no route | 5V reference (APP sensor) | — | |
| W33 | OEM-X1-56 | SP-5V1-1 | 0.5 | no route | 5V reference (APP sensor) | — | |
| W34 | OEM-X2-2 | SP-5V1-1 | 0.5 | no route | 5V reference (crankshaft sensor) | — | |
| W35 | OEM-X2-3 | SP-5V1-1 | 0.5 | no route | 5V reference (throttle body) | — | |
| W36 | OEM-X2-41 | SP-5V1-1 | 0.5 | no route | 5V reference (oil pressure) | — | |
| W37 | OEM-X2-43 | SP-5V1-1 | 0.5 | no route | 5V reference (MAP) | — | |
| W38 | OEM-X2-44 | SP-5V1-1 | 0.5 | no route | 5V reference (camshaft sensor) | — | |
| W39 | SP-5V1-1 | ME360-C1-45 | 0.5 | no route | 5V REF | — | |
| W40 | OEM-X2-68 | ME360-C1-80 | 0.5 | no route | Crankshaft position signal (58x) | — | |
| W41 | OEM-X2-64 | ME360-C1-22 | 0.5 | no route | Camshaft position signal (4x) | — | |
| W42 | OEM-X2-26 | ME360-C1-53 | 0.5 | no route | Knock sensor 1 signal A | — | |
| W43 | OEM-X2-70 | ME360-C1-32 | 0.5 | no route | Ignition coil 1 control | — | |
| W44 | OEM-X2-73 | ME360-C1-31 | 0.5 | no route | Ignition coil 2 control | — | |
| W45 | OEM-X2-77 | ME360-C1-2 | 0.5 | no route | Ignition coil 3 control | — | |
| W46 | OEM-X2-76 | ME360-C1-1 | 0.5 | no route | Ignition coil 4 control | — | |
| W47 | OEM-X2-75 | ME360-C1-59 | 0.5 | no route | Ignition coil 5 control | — | |
| W48 | OEM-X2-74 | ME360-C1-60 | 0.5 | no route | Ignition coil 6 control | — | |
| W49 | OEM-X2-20 | ME360-C1-63 | 0.5 | no route | Injector 1 | — | |
| W50 | OEM-X2-37 | ME360-C1-4 | 0.5 | no route | Injector 2 | — | |
| W51 | OEM-X2-38 | ME360-C1-33 | 0.5 | no route | Injector 3 | — | |
| W52 | OEM-X2-39 | ME360-C1-3 | 0.5 | no route | Injector 4 | — | |
| W53 | OEM-X2-18 | ME360-C1-28 | 0.5 | no route | Injector 5 | — | |
| W54 | OEM-X2-19 | ME360-C1-58 | 0.5 | no route | Injector 6 | — | |
| W55 | OEM-X2-40 | ME360-C1-63 | 0.5 | no route | Injector 7 | — | |
| W56 | OEM-X2-17 | ME360-C1-4 | 0.5 | no route | Injector 8 | — | |
| W57 | OEM-X1-50 | ME360-C1-37 | 0.5 | no route | Fuel pump relay control (primary) | — | |
| W58 | OEM-X1-59 | ME360-C1-42 | 0.5 | no route | Powertrain relay coil control (main relay) | — | |
| W59 | OEM-X1-41 | ME360-C1-26 | 0.5 | no route | Mass air flow (MAF) signal | — | |
| W60 | OEM-X2-58 | ME360-C1-56 | 0.5 | no route | Manifold absolute pressure (MAP) signal | — | |
| W61 | OEM-X1-29 | ME360-C1-17 | 0.5 | no route | Accelerator pedal position (APP) sensor 1 signal | — | |
| W62 | OEM-X2-65 | ME360-C1-18 | 0.5 | no route | Throttle position sensor 1 signal | — | |
| W63 | OEM-X2-21 | ME360-C1-86 | 0.5 | no route | Engine coolant temperature (ECT) signal | — | |
| W64 | OEM-X1-17 | ME360-C1-72 | 0.5 | no route | High speed cooling fan relay | — | |
| W65 | OEM-X1-51 | ME360-C1-43 | 0.5 | no route | Fuel pump relay control (secondary) | — | |
| W66 | OEM-X1-52 | ME360-C1-13 | 0.5 | no route | Starter enable relay control | — | |
| W67 | OEM-X1-58 | ME360-C1-75 | 0.5 | no route | Low speed cooling fan relay | — | |
| W68 | OEM-X1-63 | ME360-C1-40 | 0.5 | no route | A/C compressor clutch relay | — | |
| W69 | OEM-X1-64 | ME360-C1-16 | 0.5 | no route | HO2S heater low control, bank 2 sensor 2 | — | |
| W70 | OEM-X1-65 | ME360-C1-73 | 0.5 | no route | HO2S heater low control, bank 1 sensor 2 | — | |
| W71 | OEM-X2-12 | ME360-C1-12 | 0.5 | no route | HO2S heater low control, bank 1 sensor 1 | — | |
| W72 | OEM-X2-13 | ME360-C1-74 | 0.5 | no route | HO2S heater low control, bank 2 sensor 1 | — | |
| W73 | OEM-X2-10 | ME360-C1-44 | 0.5 | no route | Cylinder shutoff solenoid 1 (AFM) | — | |
| W74 | OEM-X2-14 | ME360-C1-69 | 0.5 | no route | Cylinder shutoff solenoid 2 (AFM) | — | |
| W75 | OEM-X2-9 | ME360-C1-39 | 0.5 | no route | Cylinder shutoff solenoid 3 (AFM) | — | |
| W76 | OEM-X2-11 | ME360-C1-9 | 0.5 | no route | Cylinder shutoff solenoid 4 (AFM) | — | |
| W77 | OEM-X1-48 | ME360-C1-79 | 0.5 | no route | Tachometer output | — | |
| W78 | OEM-X1-37 | ME360-C1-57 | 0.5 | no route | Intake air temperature (IAT) signal | — | |
| W79 | OEM-X1-71 | ME360-C1-6 | 0.5 | no route | VSS high signal (manual trans) | — | |
| W80 | OEM-X1-72 | ME360-C1-7 | 0.5 | no route | VSS low signal (manual trans) | — | |
| W81 | OEM-X1-2 | ME360-C1-8 | 0.5 | no route | 4WD low signal (1694) | — | |
| W82 | OEM-X1-1 | ME360-C1-5 | 0.5 | no route | Park/Neutral signal (1786) | — | |
| W83 | OEM-X1-3 | ME360-C1-62 | 0.5 | no route | Axle switch signal (1695) | — | |
| W84 | OEM-X1-9 | ME360-C1-34 | 0.5 | no route | Brake switch signal | — | |
| W85 | OEM-X1-28 | ME360-C1-21 | 0.5 | no route | High-speed GMLAN serial data bus + (2500) | — | |
| W86 | OEM-X1-27 | ME360-C1-51 | 0.5 | no route | High-speed GMLAN serial data bus - (2501) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (9)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | NET_MERGED | ME360-C1-4 + OEM-X2-17 + OEM-X2-37 | 2 different OEM functions share one net: OEM-X2-17 Injector 8; OEM-X2-37 Injector 2 |
| error | NET_MERGED | ME360-C1-63 + OEM-X2-20 + OEM-X2-40 | 2 different OEM functions share one net: OEM-X2-20 Injector 1; OEM-X2-40 Injector 7 |
| error | REQUIRED_UNMAPPED | OEM-X1-32 | Required OEM function "Accelerator pedal position (APP) sensor 2 signal" (analog_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X2-5 | Required OEM function "Throttle actuator motor control 2" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X2-6 | Required OEM function "Throttle actuator motor control 1" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X2-63 | Required OEM function "Throttle position sensor 2 signal" (analog_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X2-71 | Required OEM function "Ignition coil 8 control" (ignition_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-X2-72 | Required OEM function "Ignition coil 7 control" (ignition_out) is not connected to the new ECU. |
| info | UNMAPPED | OEM | 21 optional OEM pins are not mapped: OEM-X1-10 HO2S signal, bank 1 sensor 2 (post-cat); OEM-X1-12 A/C refrigerant pressure signal; OEM-X1-16 Fuel level sensor signal, primary (1589); OEM-X1-18 Accessory wakeup serial data (5985); OEM-X1-24 Fuel tank pressure signal; OEM-X1-57 VSS output to ABS (128k); OEM-X1-61 EVAP canister vent solenoid; OEM-X1-68 Malfunction indicator lamp (MIL); OEM-X1-69 HO2S signal, bank 2 sensor 2 (post-cat); OEM-X1-70 Secondary fuel level sensor signal (1937); OEM-X2-16 Camshaft actuator solenoid (VVT); OEM-X2-27 Knock sensor 1 signal B; OEM-X2-29 Knock sensor 2 signal A; OEM-X2-30 Knock sensor 2 signal B; OEM-X2-32 Generator field duty control; OEM-X2-33 Oil level switch signal; OEM-X2-50 Engine oil pressure signal; OEM-X2-57 HO2S signal, bank 1 sensor 1 (pre-cat); OEM-X2-59 HO2S signal, bank 2 sensor 1 (pre-cat); OEM-X2-61 Charge indicator signal; OEM-X2-8 EVAP canister purge solenoid |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-X1-20 | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-11. Review every wire against both manuals before building. Open items: - OEM-X2 72: Ignition coil 7 control: no free ignition output on Motorsport Electronics ME360 - OEM-X2 71: Ignition coil 8 control: no free ignition output on Motorsport Electronics ME360 - OEM-X1 32: Accelerator pedal position (APP) sensor 2 signal: no free tps/analog_0_5 on Motorsport Electronics ME360 - OEM-X2 63: Throttle position sensor 2 signal: no free tps/analog_0_5 on Motorsport Electronics ME360 - OEM-X2 6: Throttle actuator motor control 1: no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-X2 5: Throttle actuator motor control 2: no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand Not wired: - OEM-X1 20: Battery positive voltage (batt hot): Motorsport Electronics ME360 has no battery-constant input; not needed - OEM-X2 27: Knock sensor 1 signal B: no free knock input on Motorsport Electronics ME360 - OEM-X2 29: Knock sensor 2 signal A: no free knock input on Motorsport Electronics ME360 - OEM-X2 30: Knock sensor 2 signal B: no free knock input on Motorsport Electronics ME360 - OEM-X1 61: EVAP canister vent solenoid: no free low_side/relay_control/heater_low_side/ls_hs/injector on Motorsport Electronics ME360 - OEM-X1 68: Malfunction indicator lamp (MIL): no free low_side/relay_control/heater_low_side/ls_hs/injector on Motorsport Electronics ME360 - OEM-X2 16: Camshaft actuator solenoid (VVT): no free low_side/relay_control/heater_low_side/ls_hs/injector on Motorsport Electronics ME360 - OEM-X2 32: Generator field duty control: no free low_side/relay_control/heater_low_side/ls_hs/injector on Motorsport Electronics ME360 - OEM-X2 61: Charge indicator signal: no free low_side/relay_control/heater_low_side/ls_hs/injector on Motorsport Electronics ME360 - OEM-X2 8: EVAP canister purge solenoid: no free low_side/relay_control/heater_low_side/ls_hs/injector on Motorsport Electronics ME360 - OEM-X1 57: VSS output to ABS (128k): no free frequency_out/tacho/low_side/ls_hs on Motorsport Electronics ME360 - OEM-X1 10: HO2S signal, bank 1 sensor 2 (post-cat): no free o2_narrowband/analog_0_5 on Motorsport Electronics ME360 - OEM-X1 69: HO2S signal, bank 2 sensor 2 (post-cat): no free o2_narrowband/analog_0_5 on Motorsport Electronics ME360 - OEM-X2 57: HO2S signal, bank 1 sensor 1 (pre-cat): no free o2_narrowband/analog_0_5 on Motorsport Electronics ME360 - OEM-X2 59: HO2S signal, bank 2 sensor 1 (pre-cat): no free o2_narrowband/analog_0_5 on Motorsport Electronics ME360 - OEM-X1 12: A/C refrigerant pressure signal: no free analog_0_5 on Motorsport Electronics ME360 - OEM-X1 16: Fuel level sensor signal, primary (1589): no free analog_0_5 on Motorsport Electronics ME360 - OEM-X1 24: Fuel tank pressure signal: no free analog_0_5 on Motorsport Electronics ME360 - OEM-X1 70: Secondary fuel level sensor signal (1937): no free analog_0_5 on Motorsport Electronics ME360 - OEM-X2 50: Engine oil pressure signal: no free analog_0_5 on Motorsport Electronics ME360 - OEM-X2 33: Oil level switch signal: no free switch_in/frequency_in/analog_0_5 on Motorsport Electronics ME360 - OEM-X1 18: Accessory wakeup serial data (5985): no free k_line on Motorsport Electronics ME360
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | MaxxECU webhelp: Wiring — plug-in ECU Chevrolet Corvette C6 (GM E38 ECM) | http://www.maxxecu.com/webhelp/wirings-pluginecu-chevrolet_corvette_c6_e38_ecm.html | — | — | — |
| 4 | vendor_doc | Motorsport Electronics GEN2 ME221/ME360/ME442 wire-in pinout | https://motorsport-electronics.co.uk/onlinehelp/html/ME442ME360ME221GEN2Wire-InPinout.html | — | — | — |
| 2 | community_copy | lt1swap.com: E38 ECM Connector Pinouts | https://lt1swap.com/E38 ECM Connector Pinouts.htm | — | — | — |