Honda NSX NA2 1997-2005 (C32B) → MoTeC M130 13130 (auto)
Honda NSX NA2 1997-2005 (C32B) — MoTeC — M130
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-12
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 5: read the Findings page before cutting any wire |
| Size of the job | 64 wires · 12 connectors · 0 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-A-13 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-C-1 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | OEM-G-10 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-G-2 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-G-3 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-G-9 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | SP-14V-1 | M130-A-26 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-D-1 | M130-B-12 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | OEM-A-12 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-A-25 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-G-7 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-G-8 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | SP-GND-1 | M130-A-10 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | SP-GND-1 | M130-A-11 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-A-26 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-B-13 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-B-14 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-B-15 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-B-16 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-B-9 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-D-11 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-F-15 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-F-2 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | SP-0V-1 | M130-B-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | SP-0V-1 | M130-B-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-D-10 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-F-1 | SP-5V1-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | SP-5V1-1 | M130-A-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-F-14 | M130-A-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-B-8 | M130-B-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-B-7 | M130-B-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-B-6 | M130-B-8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-B-5 | M130-B-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-D-13 | M130-B-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-D-2 | M130-B-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-A-11 | M130-A-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-A-24 | M130-A-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-B-12 | M130-A-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-B-11 | M130-A-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-B-10 | M130-A-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-B-2 | M130-A-8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-A-1 | M130-A-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-A-2 | M130-A-23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-A-3 | M130-A-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-A-14 | M130-A-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-A-15 | M130-A-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | OEM-A-16 | M130-A-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | OEM-A-5 | M130-A-27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W49 | OEM-F-19 | M130-A-28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W50 | OEM-F-20 | M130-A-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W51 | OEM-D-9 | M130-A-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W52 | OEM-F-13 | M130-A-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W53 | OEM-F-12 | M130-A-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W54 | OEM-D-12 | M130-A-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W55 | OEM-D-7 | M130-B-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W56 | OEM-F-4 | M130-A-30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W57 | OEM-D-16 | M130-A-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W58 | OEM-D-17 | M130-B-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W59 | OEM-D-18 | M130-B-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W60 | OEM-D-19 | M130-B-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W61 | OEM-D-8 | M130-B-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W62 | OEM-C-7 | M130-B-10 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W63 | OEM-F-16 | M130-B-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W64 | OEM-F-6 | M130-B-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | M130-A-26 | M130-B-15 | open (OL) | +12 V supply must not touch sensor ground | |
| 2 | M130-A-10 | M130-A-2 | open (OL) | power ground must not touch 5 V sensor reference | |
| 3 | M130-A-10 | M130-A-26 | open (OL) | power ground must not touch +12 V supply | |
| 4 | M130-A-10 | M130-A-9 | open (OL) | power ground must not touch 5 V sensor reference | |
| 5 | M130-A-10 | M130-B-12 | open (OL) | power ground must not touch +12 V supply | |
| 6 | M130-A-26 | M130-A-2 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 7 | M130-A-26 | M130-A-9 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 8 | M130-B-12 | M130-A-2 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 9 | M130-B-12 | M130-A-9 | open (OL) | +12 V supply must not touch 5 V sensor reference | |
| 10 | M130-B-15 | M130-A-2 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 11 | M130-B-15 | M130-A-9 | open (OL) | sensor ground must not touch 5 V sensor reference | |
| 12 | M130-B-15 | M130-B-12 | open (OL) | sensor ground must not touch +12 V supply |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
M130-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Half Bridge Output 2 | — | — | — | — | — | — | — | — |
| 10 | Battery Negative 1 | — | W13 | — | 0.85 | SP-GND-1 | — | — | — |
| 11 | Battery Negative 2 | — | W14 | — | 0.85 | SP-GND-1 | — | — | — |
| 12 | Low Side Ignition 7 | — | — | — | — | — | — | — | — |
| 13 | Low Side Ignition 8 | — | — | — | — | — | — | — | — |
| 14 | Analogue Voltage Input 1 | — | W51 | — | 0.5 | OEM-D-9 | — | — | — |
| 15 | Analogue Voltage Input 2 | — | W52 | — | 0.5 | OEM-F-13 | — | — | — |
| 16 | Analogue Voltage Input 3 | — | W53 | — | 0.5 | OEM-F-12 | — | — | — |
| 17 | Analogue Voltage Input 4 | — | W54 | — | 0.5 | OEM-D-12 | — | — | — |
| 18 | Half Bridge Output 1 | — | — | — | — | — | — | — | — |
| 19 | Peak Hold Injector 1 | — | W42 | — | 0.5 | OEM-A-1 | — | — | — |
| 2 | Sensor 5.0V A | — | W29 | — | 0.5 | OEM-F-14 | — | — | — |
| 20 | Peak Hold Injector 2 | — | W44 | — | 0.5 | OEM-A-3 | — | — | — |
| 21 | Peak Hold Injector 3 | — | W46 | — | 0.5 | OEM-A-15 | — | — | — |
| 22 | Peak Hold Injector 4 | — | W47 | — | 0.5 | OEM-A-16 | — | — | — |
| 23 | Low Side Injector 1 | — | W43 | — | 0.5 | OEM-A-2 | — | — | — |
| 24 | Low Side Injector 2 | — | W45 | — | 0.5 | OEM-A-14 | — | — | — |
| 25 | Analogue Voltage Input 5 | — | W57 | — | 0.5 | OEM-D-16 | — | — | — |
| 26 | Battery Positive | — | W7 | — | 0.85 | SP-14V-1 | — | — | — |
| 27 | Peak Hold Injector 5 | — | W48 | — | 0.5 | OEM-A-5 | — | — | — |
| 28 | Peak Hold Injector 6 | — | W49 | — | 0.5 | OEM-F-19 | — | — | — |
| 29 | Peak Hold Injector 7 | — | W50 | — | 0.5 | OEM-F-20 | — | — | — |
| 3 | Low Side Ignition 1 | — | W36 | — | 0.5 | OEM-A-11 | — | — | — |
| 30 | Peak Hold Injector 8 | — | W56 | — | 0.5 | OEM-F-4 | — | — | — |
| 31 | Half Bridge Output 3 | — | — | — | — | — | — | — | — |
| 32 | Half Bridge Output 4 | — | — | — | — | — | — | — | — |
| 33 | Half Bridge Output 5 | — | — | — | — | — | — | — | — |
| 34 | Half Bridge Output 6 | — | — | — | — | — | — | — | — |
| 4 | Low Side Ignition 2 | — | W37 | — | 0.5 | OEM-A-24 | — | — | — |
| 5 | Low Side Ignition 3 | — | W38 | — | 0.5 | OEM-B-12 | — | — | — |
| 6 | Low Side Ignition 4 | — | W39 | — | 0.5 | OEM-B-11 | — | — | — |
| 7 | Low Side Ignition 5 | — | W40 | — | 0.5 | OEM-B-10 | — | — | — |
| 8 | Low Side Ignition 6 | — | W41 | — | 0.5 | OEM-B-2 | — | — | — |
| 9 | Sensor 5.0V B | — | W28 | — | 0.5 | SP-5V1-1 | — | — | — |
M130-B
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Universal Digital Input 1 | — | W30 | — | 0.5 | OEM-B-8 | — | — | — |
| 10 | Universal Digital Input 5 | — | W62 | — | 0.5 | OEM-C-7 | — | — | — |
| 11 | Universal Digital Input 6 | — | W63 | — | 0.5 | OEM-F-16 | — | — | — |
| 12 | Battery Backup | — | W8 | — | 0.85 | OEM-D-1 | — | — | — |
| 13 | Knock Input 2 | — | W35 | — | 0.5 | OEM-D-2 | — | — | — |
| 14 | Universal Digital Input 7 | — | W64 | — | 0.5 | OEM-F-6 | — | — | — |
| 15 | Sensor 0V A | — | W24 | — | 0.5 | SP-0V-1 | — | — | — |
| 16 | Sensor 0V B | — | W25 | — | 0.5 | SP-0V-1 | — | — | — |
| 17 | CAN Bus 1 High | — | — | — | — | — | — | — | — |
| 18 | CAN Bus 1 Low | — | — | — | — | — | — | — | — |
| 19 | Sensor 6.3V | — | — | — | — | — | — | — | — |
| 2 | Universal Digital Input 2 | — | W31 | — | 0.5 | OEM-B-7 | — | — | — |
| 20 | Analogue Voltage Input 6 | — | W58 | — | 0.5 | OEM-D-17 | — | — | — |
| 21 | Analogue Voltage Input 7 | — | W59 | — | 0.5 | OEM-D-18 | — | — | — |
| 22 | Analogue Voltage Input 8 | — | W60 | — | 0.5 | OEM-D-19 | — | — | — |
| 23 | Ethernet Transmit + | — | — | — | — | — | — | — | — |
| 24 | Ethernet Transmit - | — | — | — | — | — | — | — | — |
| 25 | Ethernet Receive + | — | — | — | — | — | — | — | — |
| 26 | Ethernet Receive - | — | — | — | — | — | — | — | — |
| 3 | Analogue Temperature Input 1 | — | W55 | — | 0.5 | OEM-D-7 | — | — | — |
| 4 | Analogue Temperature Input 2 | — | W61 | — | 0.5 | OEM-D-8 | — | — | — |
| 5 | Analogue Temperature Input 3 | — | — | — | — | — | — | — | — |
| 6 | Analogue Temperature Input 4 | — | — | — | — | — | — | — | — |
| 7 | Knock Input 1 | — | W34 | — | 0.5 | OEM-D-13 | — | — | — |
| 8 | Universal Digital Input 3 | — | W32 | — | 0.5 | OEM-B-6 | — | — | — |
| 9 | Universal Digital Input 4 | — | W33 | — | 0.5 | OEM-B-5 | — | — | — |
OEM-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector 1 (INJ1) | — | W42 | — | 0.5 | M130-A-19 | — | — | — |
| 10 | Rear secondary O2 heater (RSO2SHTC) | — | — | — | — | — | — | — | — |
| 11 | Ignition coil 1 (IGN COIL1) | — | W36 | — | 0.5 | M130-A-3 | — | — | — |
| 12 | Power ground (PG1) | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 13 | ECM power source (IGP1) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 14 | Injector 4 (INJ4) | — | W45 | — | 0.5 | M130-A-24 | — | — | — |
| 15 | Injector 5 (INJ5) | — | W46 | — | 0.5 | M130-A-21 | — | — | — |
| 16 | Injector 6 (INJ6) | — | W47 | — | 0.5 | M130-A-22 | — | — | — |
| 17 | EVAP bypass solenoid (2WBS) | — | — | — | — | — | — | — | — |
| 2 | Injector 2 (INJ2) | — | W43 | — | 0.5 | M130-A-23 | — | — | — |
| 20 | IAB control solenoid (IABCS) | — | — | — | — | — | — | — | — |
| 21 | EVAP purge control solenoid (PCS) | — | — | — | — | — | — | — | — |
| 22 | Front primary O2 heater (FPO2SHTC) | — | — | — | — | — | — | — | — |
| 23 | Rear primary O2 heater (RPO2SHTC) | — | — | — | — | — | — | — | — |
| 24 | Ignition coil 2 (IGN COIL2) | — | W37 | — | 0.5 | M130-A-4 | — | — | — |
| 25 | Power ground (PG2) | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 26 | Logic ground (LG1) | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 3 | Injector 3 (INJ3) | — | W44 | — | 0.5 | M130-A-20 | — | — | — |
| 4 | EVAP canister vent shut valve (VSV) | — | — | — | — | — | — | — | — |
| 5 | Fuel pump relay (FLR1) | — | W48 | — | 0.5 | M130-A-27 | — | — | — |
| 6 | EGR control solenoid (ESOL) | — | — | — | — | — | — | — | — |
| 7 | Malfunction indicator lamp (MIL) | — | — | — | — | — | — | — | — |
| 8 | A/C clutch relay (ACC) | — | — | — | — | — | — | — | — |
| 9 | Front secondary O2 heater (FSO2SHTC) | — | — | — | — | — | — | — | — |
OEM-B
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | VTEC pressure switch front (VTP SWF) | — | — | — | — | — | — | — | — |
| 10 | Ignition coil 5 (IGN COIL5) | — | W40 | — | 0.5 | M130-A-7 | — | — | — |
| 11 | Ignition coil 4 (IGN COIL4) | — | W39 | — | 0.5 | M130-A-6 | — | — | — |
| 12 | Ignition coil 3 (IGN COIL3) | — | W38 | — | 0.5 | M130-A-5 | — | — | — |
| 13 | Cylinder position sensor 2 return (CYP 2M) | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 14 | Cylinder position sensor 1 return (CYP 1M) | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 15 | Crank position sensor 2 return (CKP 2M) | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 16 | Crank position sensor 1 return (CKP 1M) | — | W19 | — | 0.5 | SP-0V-1 | — | — | — |
| 2 | Ignition coil 6 (IGN COIL6) | — | W41 | — | 0.5 | M130-A-8 | — | — | — |
| 3 | VTEC pressure switch rear (VTP SWR) | — | — | — | — | — | — | — | — |
| 4 | Neutral switch (NT SW, M/T) | — | — | — | — | — | — | — | — |
| 5 | Cylinder position sensor 2 + (CYP 2P) | — | W33 | — | 0.5 | M130-B-9 | — | — | — |
| 6 | Cylinder position sensor 1 + (CYP 1P) | — | W32 | — | 0.5 | M130-B-8 | — | — | — |
| 7 | Crank position sensor 2 + (CKP 2P) | — | W31 | — | 0.5 | M130-B-2 | — | — | — |
| 8 | Crank position sensor 1 + (CKP 1P) | — | W30 | — | 0.5 | M130-B-1 | — | — | — |
| 9 | Logic ground (LG2) | — | W20 | — | 0.5 | SP-0V-1 | — | — | — |
OEM-C
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | ECM power source (IGP2) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 4 | Clutch switch (MTCLS, M/T) | — | — | — | — | — | — | — | — |
| 6 | Starter switch (STS) | — | — | — | — | — | — | — | — |
| 7 | Vehicle speed sensor (VSS) | — | W62 | — | 0.5 | M130-B-10 | — | — | — |
| 8 | Engine speed pulse (NEP) | — | — | — | — | — | — | — | — |
OEM-D
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Backup power (VBU) | — | W8 | — | 0.85 | M130-B-12 | — | — | — |
| 10 | Sensor 5V supply (VCC2) | — | W26 | — | 0.5 | SP-5V1-1 | — | — | — |
| 11 | Sensor ground (SG2) | — | W21 | — | 0.5 | SP-0V-1 | — | — | — |
| 12 | Throttle position sensor (TPS) | — | W54 | — | 0.5 | M130-A-17 | — | — | — |
| 13 | Knock sensor front (KSF) | — | W34 | — | 0.5 | M130-B-7 | — | — | — |
| 16 | Front secondary O2 signal (O2S FS) | — | W57 | — | 0.5 | M130-A-25 | — | — | — |
| 17 | Rear secondary O2 signal (O2S RS) | — | W58 | — | 0.5 | M130-B-20 | — | — | — |
| 18 | Front primary O2 signal (O2S FP) | — | W59 | — | 0.5 | M130-B-21 | — | — | — |
| 19 | Rear primary O2 signal (O2S RP) | — | W60 | — | 0.5 | M130-B-22 | — | — | — |
| 2 | Knock sensor rear (KSR) | — | W35 | — | 0.5 | M130-B-13 | — | — | — |
| 20 | EGR valve lift sensor (EGRL) | — | — | — | — | — | — | — | — |
| 4 | K-line diagnostics | — | — | — | — | — | — | — | — |
| 7 | Engine coolant temperature (ECT) | — | W55 | — | 0.5 | M130-B-3 | — | — | — |
| 8 | Intake air temperature (IAT) | — | W61 | — | 0.5 | M130-B-4 | — | — | — |
| 9 | MAP sensor | — | W51 | — | 0.5 | M130-A-14 | — | — | — |
OEM-F
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Sensor 5V supply (VCC1) | — | W27 | — | 0.5 | SP-5V1-1 | — | — | — |
| 12 | Accelerator pedal position 2 (AP2) | — | W53 | — | 0.5 | M130-A-16 | — | — | — |
| 13 | Accelerator pedal position 1 (AP1) | — | W52 | — | 0.5 | M130-A-15 | — | — | — |
| 14 | Accelerator pedal 5V supply (VCC3) | — | W29 | — | 0.5 | M130-A-2 | — | — | — |
| 15 | Accelerator pedal ground (SG3) | — | W22 | — | 0.5 | SP-0V-1 | — | — | — |
| 16 | Brake switch 1 (BKSW1) | — | W63 | — | 0.5 | M130-B-11 | — | — | — |
| 19 | VTEC solenoid front (VT SOLF) | — | W49 | — | 0.5 | M130-A-28 | — | — | — |
| 2 | Sensor ground (SG1) | — | W23 | — | 0.5 | SP-0V-1 | — | — | — |
| 20 | VTEC solenoid rear (VT SOLR) | — | W50 | — | 0.5 | M130-A-29 | — | — | — |
| 4 | Fuel pump relay 2 (FLR2) | — | W56 | — | 0.5 | M130-A-30 | — | — | — |
| 6 | Brake switch 2 (BKSW2) | — | W64 | — | 0.5 | M130-B-14 | — | — | — |
OEM-G
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | Throttle motor common power phases 2&4 (COM2) | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 11 | Throttle motor phase 3 (PM3) | — | — | — | — | — | — | — | — |
| 12 | Throttle motor phase 4 (PM4) | — | — | — | — | — | — | — | — |
| 2 | Throttle motor power source 1 (IGM1) | — | W4 | — | 0.85 | SP-14V-1 | — | — | — |
| 3 | Throttle motor power source 2 (IGM2) | — | W5 | — | 0.85 | SP-14V-1 | — | — | — |
| 4 | Throttle motor phase 1 (PM1) | — | — | — | — | — | — | — | — |
| 5 | Throttle motor phase 2 (PM2) | — | — | — | — | — | — | — | — |
| 7 | Throttle motor ground 1 (PGM1) | — | W11 | — | 0.85 | SP-GND-1 | — | — | — |
| 8 | Throttle motor ground 2 (PGM2) | — | W12 | — | 0.85 | SP-GND-1 | — | — | — |
| 9 | Throttle motor common power phases 1&3 (COM1) | — | W6 | — | 0.85 | SP-14V-1 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W15 | — | 0.5 | OEM-A-26 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-B-13 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | OEM-B-14 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | OEM-B-15 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | OEM-B-16 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | OEM-B-9 | — | — | — |
| 1 | — | — | W21 | — | 0.5 | OEM-D-11 | — | — | — |
| 1 | — | — | W22 | — | 0.5 | OEM-F-15 | — | — | — |
| 1 | — | — | W23 | — | 0.5 | OEM-F-2 | — | — | — |
| 1 | — | — | W24 | — | 0.5 | M130-B-15 | — | — | — |
| 1 | — | — | W25 | — | 0.5 | M130-B-16 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-A-13 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-C-1 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | OEM-G-10 | — | — | — |
| 1 | — | — | W4 | — | 0.85 | OEM-G-2 | — | — | — |
| 1 | — | — | W5 | — | 0.85 | OEM-G-3 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-G-9 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | M130-A-26 | — | — | — |
SP-5V1
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W26 | — | 0.5 | OEM-D-10 | — | — | — |
| 1 | — | — | W27 | — | 0.5 | OEM-F-1 | — | — | — |
| 1 | — | — | W28 | — | 0.5 | M130-A-9 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W9 | — | 0.85 | OEM-A-12 | — | — | — |
| 1 | — | — | W10 | — | 0.85 | OEM-A-25 | — | — | — |
| 1 | — | — | W11 | — | 0.85 | OEM-G-7 | — | — | — |
| 1 | — | — | W12 | — | 0.85 | OEM-G-8 | — | — | — |
| 1 | — | — | W13 | — | 0.85 | M130-A-10 | — | — | — |
| 1 | — | — | W14 | — | 0.85 | M130-A-11 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-A-1 | Injector 1 (INJ1) | injector_out | M130-A-19 | Peak Hold Injector 1 | injector_out | single_source | |
| OEM-A-10 | Rear secondary O2 heater (RSO2SHTC) | low_side_out | — | — | — | single_source | |
| OEM-A-11 | Ignition coil 1 (IGN COIL1) | ignition_out | M130-A-3 | Low Side Ignition 1 | ignition_out | single_source | |
| OEM-A-12 | Power ground (PG1) | ground | M130-A-10 + M130-A-11 | Battery Negative 1 + Battery Negative 2 | ground | single_source | |
| OEM-A-13 | ECM power source (IGP1) | power_in | M130-A-26 | Battery Positive | power_in | single_source | |
| OEM-A-14 | Injector 4 (INJ4) | injector_out | M130-A-24 | Low Side Injector 2 | injector_out | single_source | |
| OEM-A-15 | Injector 5 (INJ5) | injector_out | M130-A-21 | Peak Hold Injector 3 | injector_out | single_source | |
| OEM-A-16 | Injector 6 (INJ6) | injector_out | M130-A-22 | Peak Hold Injector 4 | injector_out | single_source | |
| OEM-A-17 | EVAP bypass solenoid (2WBS) | low_side_out | — | — | — | single_source | |
| OEM-A-2 | Injector 2 (INJ2) | injector_out | M130-A-23 | Low Side Injector 1 | injector_out | single_source | |
| OEM-A-20 | IAB control solenoid (IABCS) | low_side_out | — | — | — | single_source | |
| OEM-A-21 | EVAP purge control solenoid (PCS) | low_side_out | — | — | — | single_source | |
| OEM-A-22 | Front primary O2 heater (FPO2SHTC) | low_side_out | — | — | — | single_source | |
| OEM-A-23 | Rear primary O2 heater (RPO2SHTC) | low_side_out | — | — | — | single_source | |
| OEM-A-24 | Ignition coil 2 (IGN COIL2) | ignition_out | M130-A-4 | Low Side Ignition 2 | ignition_out | single_source | |
| OEM-A-25 | Power ground (PG2) | ground | M130-A-10 + M130-A-11 | Battery Negative 1 + Battery Negative 2 | ground | single_source | |
| OEM-A-26 | Logic ground (LG1) | sensor_ground | M130-B-15 + M130-B-16 | Sensor 0V A + Sensor 0V B | sensor_ground | single_source | |
| OEM-A-3 | Injector 3 (INJ3) | injector_out | M130-A-20 | Peak Hold Injector 2 | injector_out | single_source | |
| OEM-A-4 | EVAP canister vent shut valve (VSV) | low_side_out | — | — | — | single_source | |
| OEM-A-5 | Fuel pump relay (FLR1) | low_side_out | M130-A-27 | Peak Hold Injector 5 | injector_out | single_source | |
| OEM-A-6 | EGR control solenoid (ESOL) | low_side_out | — | — | — | single_source | |
| OEM-A-7 | Malfunction indicator lamp (MIL) | low_side_out | — | — | — | single_source | |
| OEM-A-8 | A/C clutch relay (ACC) | low_side_out | — | — | — | single_source | |
| OEM-A-9 | Front secondary O2 heater (FSO2SHTC) | low_side_out | — | — | — | single_source | |
| OEM-B-1 | VTEC pressure switch front (VTP SWF) | digital_in | — | — | — | single_source | |
| OEM-B-10 | Ignition coil 5 (IGN COIL5) | ignition_out | M130-A-7 | Low Side Ignition 5 | ignition_out | single_source | |
| OEM-B-11 | Ignition coil 4 (IGN COIL4) | ignition_out | M130-A-6 | Low Side Ignition 4 | ignition_out | single_source | |
| OEM-B-12 | Ignition coil 3 (IGN COIL3) | ignition_out | M130-A-5 | Low Side Ignition 3 | ignition_out | single_source | |
| OEM-B-13 | Cylinder position sensor 2 return (CYP 2M) | sensor_ground | M130-B-15 + M130-B-16 | Sensor 0V A + Sensor 0V B | sensor_ground | single_source | |
| OEM-B-14 | Cylinder position sensor 1 return (CYP 1M) | sensor_ground | M130-B-15 + M130-B-16 | Sensor 0V A + Sensor 0V B | sensor_ground | single_source | |
| OEM-B-15 | Crank position sensor 2 return (CKP 2M) | sensor_ground | M130-B-15 + M130-B-16 | Sensor 0V A + Sensor 0V B | sensor_ground | single_source | |
| OEM-B-16 | Crank position sensor 1 return (CKP 1M) | sensor_ground | M130-B-15 + M130-B-16 | Sensor 0V A + Sensor 0V B | sensor_ground | single_source | |
| OEM-B-2 | Ignition coil 6 (IGN COIL6) | ignition_out | M130-A-8 | Low Side Ignition 6 | ignition_out | single_source | |
| OEM-B-3 | VTEC pressure switch rear (VTP SWR) | digital_in | — | — | — | single_source | |
| OEM-B-4 | Neutral switch (NT SW, M/T) | digital_in | — | — | — | single_source | |
| OEM-B-5 | Cylinder position sensor 2 + (CYP 2P) | trigger_in | M130-B-9 | Universal Digital Input 4 | digital_in | single_source | |
| OEM-B-6 | Cylinder position sensor 1 + (CYP 1P) | trigger_in | M130-B-8 | Universal Digital Input 3 | digital_in | single_source | |
| OEM-B-7 | Crank position sensor 2 + (CKP 2P) | trigger_in | M130-B-2 | Universal Digital Input 2 | digital_in | single_source | |
| OEM-B-8 | Crank position sensor 1 + (CKP 1P) | trigger_in | M130-B-1 | Universal Digital Input 1 | digital_in | single_source | |
| OEM-B-9 | Logic ground (LG2) | sensor_ground | M130-B-15 + M130-B-16 | Sensor 0V A + Sensor 0V B | sensor_ground | single_source | |
| OEM-C-1 | ECM power source (IGP2) | power_in | M130-A-26 | Battery Positive | power_in | single_source | |
| OEM-C-4 | Clutch switch (MTCLS, M/T) | digital_in | — | — | — | single_source | |
| OEM-C-6 | Starter switch (STS) | digital_in | — | — | — | single_source | |
| OEM-C-7 | Vehicle speed sensor (VSS) | digital_in | M130-B-10 | Universal Digital Input 5 | digital_in | single_source | |
| OEM-C-8 | Engine speed pulse (NEP) | tacho_out | — | — | — | single_source | |
| OEM-D-1 | Backup power (VBU) | power_in | M130-B-12 | Battery Backup | power_in | single_source | |
| OEM-D-10 | Sensor 5V supply (VCC2) | vref | M130-A-9 | Sensor 5.0V B | vref | single_source | |
| OEM-D-11 | Sensor ground (SG2) | sensor_ground | M130-B-15 + M130-B-16 | Sensor 0V A + Sensor 0V B | sensor_ground | single_source | |
| OEM-D-12 | Throttle position sensor (TPS) | analog_in | M130-A-17 | Analogue Voltage Input 4 | analog_in | single_source | |
| OEM-D-13 | Knock sensor front (KSF) | knock_in | M130-B-7 | Knock Input 1 | knock_in | single_source | |
| OEM-D-16 | Front secondary O2 signal (O2S FS) | lambda_nb_in | M130-A-25 | Analogue Voltage Input 5 | analog_in | single_source | |
| OEM-D-17 | Rear secondary O2 signal (O2S RS) | lambda_nb_in | M130-B-20 | Analogue Voltage Input 6 | analog_in | single_source | |
| OEM-D-18 | Front primary O2 signal (O2S FP) | lambda_nb_in | M130-B-21 | Analogue Voltage Input 7 | analog_in | single_source | |
| OEM-D-19 | Rear primary O2 signal (O2S RP) | lambda_nb_in | M130-B-22 | Analogue Voltage Input 8 | analog_in | single_source | |
| OEM-D-2 | Knock sensor rear (KSR) | knock_in | M130-B-13 | Knock Input 2 | knock_in | single_source | |
| OEM-D-20 | EGR valve lift sensor (EGRL) | analog_in | — | — | — | single_source | |
| OEM-D-4 | K-line diagnostics | serial | — | — | — | single_source | |
| OEM-D-7 | Engine coolant temperature (ECT) | temp_in | M130-B-3 | Analogue Temperature Input 1 | temp_in | single_source | |
| OEM-D-8 | Intake air temperature (IAT) | temp_in | M130-B-4 | Analogue Temperature Input 2 | temp_in | single_source | |
| OEM-D-9 | MAP sensor | analog_in | M130-A-14 | Analogue Voltage Input 1 | analog_in | single_source | |
| OEM-F-1 | Sensor 5V supply (VCC1) | vref | M130-A-9 | Sensor 5.0V B | vref | single_source | |
| OEM-F-12 | Accelerator pedal position 2 (AP2) | analog_in | M130-A-16 | Analogue Voltage Input 3 | analog_in | single_source | |
| OEM-F-13 | Accelerator pedal position 1 (AP1) | analog_in | M130-A-15 | Analogue Voltage Input 2 | analog_in | single_source | |
| OEM-F-14 | Accelerator pedal 5V supply (VCC3) | vref | M130-A-2 | Sensor 5.0V A | vref | single_source | |
| OEM-F-15 | Accelerator pedal ground (SG3) | sensor_ground | M130-B-15 + M130-B-16 | Sensor 0V A + Sensor 0V B | sensor_ground | single_source | |
| OEM-F-16 | Brake switch 1 (BKSW1) | digital_in | M130-B-11 | Universal Digital Input 6 | digital_in | single_source | |
| OEM-F-19 | VTEC solenoid front (VT SOLF) | low_side_out | M130-A-28 | Peak Hold Injector 6 | injector_out | single_source | |
| OEM-F-2 | Sensor ground (SG1) | sensor_ground | M130-B-15 + M130-B-16 | Sensor 0V A + Sensor 0V B | sensor_ground | single_source | |
| OEM-F-20 | VTEC solenoid rear (VT SOLR) | low_side_out | M130-A-29 | Peak Hold Injector 7 | injector_out | single_source | |
| OEM-F-4 | Fuel pump relay 2 (FLR2) | low_side_out | M130-A-30 | Peak Hold Injector 8 | injector_out | single_source | |
| OEM-F-6 | Brake switch 2 (BKSW2) | digital_in | M130-B-14 | Universal Digital Input 7 | digital_in | single_source | |
| OEM-G-10 | Throttle motor common power phases 2&4 (COM2) | power_in | M130-A-26 | Battery Positive | power_in | single_source | |
| OEM-G-11 | Throttle motor phase 3 (PM3) | hbridge_out | — | — | — | single_source | |
| OEM-G-12 | Throttle motor phase 4 (PM4) | hbridge_out | — | — | — | single_source | |
| OEM-G-2 | Throttle motor power source 1 (IGM1) | power_in | M130-A-26 | Battery Positive | power_in | single_source | |
| OEM-G-3 | Throttle motor power source 2 (IGM2) | power_in | M130-A-26 | Battery Positive | power_in | single_source | |
| OEM-G-4 | Throttle motor phase 1 (PM1) | hbridge_out | — | — | — | single_source | |
| OEM-G-5 | Throttle motor phase 2 (PM2) | hbridge_out | — | — | — | single_source | |
| OEM-G-7 | Throttle motor ground 1 (PGM1) | ground | M130-A-10 + M130-A-11 | Battery Negative 1 + Battery Negative 2 | ground | single_source | |
| OEM-G-8 | Throttle motor ground 2 (PGM2) | ground | M130-A-10 + M130-A-11 | Battery Negative 1 + Battery Negative 2 | ground | single_source | |
| OEM-G-9 | Throttle motor common power phases 1&3 (COM1) | power_in | M130-A-26 | Battery Positive | power_in | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-A-13 | SP-14V-1 | 0.85 | no route | ECM power source (IGP1) | — | |
| W2 | OEM-C-1 | SP-14V-1 | 0.85 | no route | ECM power source (IGP2) | — | |
| W3 | OEM-G-10 | SP-14V-1 | 0.85 | no route | Throttle motor common power phases 2&4 (COM2) | — | |
| W4 | OEM-G-2 | SP-14V-1 | 0.85 | no route | Throttle motor power source 1 (IGM1) | — | |
| W5 | OEM-G-3 | SP-14V-1 | 0.85 | no route | Throttle motor power source 2 (IGM2) | — | |
| W6 | OEM-G-9 | SP-14V-1 | 0.85 | no route | Throttle motor common power phases 1&3 (COM1) | — | |
| W7 | SP-14V-1 | M130-A-26 | 0.85 | no route | Battery Positive | — | |
| W8 | OEM-D-1 | M130-B-12 | 0.85 | no route | Backup power (VBU) | — | |
| W9 | OEM-A-12 | SP-GND-1 | 0.85 | no route | Power ground (PG1) | — | |
| W10 | OEM-A-25 | SP-GND-1 | 0.85 | no route | Power ground (PG2) | — | |
| W11 | OEM-G-7 | SP-GND-1 | 0.85 | no route | Throttle motor ground 1 (PGM1) | — | |
| W12 | OEM-G-8 | SP-GND-1 | 0.85 | no route | Throttle motor ground 2 (PGM2) | — | |
| W13 | SP-GND-1 | M130-A-10 | 0.85 | no route | Battery Negative 1 | — | |
| W14 | SP-GND-1 | M130-A-11 | 0.85 | no route | Battery Negative 2 | — | |
| W15 | OEM-A-26 | SP-0V-1 | 0.5 | no route | Logic ground (LG1) | — | |
| W16 | OEM-B-13 | SP-0V-1 | 0.5 | no route | Cylinder position sensor 2 return (CYP 2M) | — | |
| W17 | OEM-B-14 | SP-0V-1 | 0.5 | no route | Cylinder position sensor 1 return (CYP 1M) | — | |
| W18 | OEM-B-15 | SP-0V-1 | 0.5 | no route | Crank position sensor 2 return (CKP 2M) | — | |
| W19 | OEM-B-16 | SP-0V-1 | 0.5 | no route | Crank position sensor 1 return (CKP 1M) | — | |
| W20 | OEM-B-9 | SP-0V-1 | 0.5 | no route | Logic ground (LG2) | — | |
| W21 | OEM-D-11 | SP-0V-1 | 0.5 | no route | Sensor ground (SG2) | — | |
| W22 | OEM-F-15 | SP-0V-1 | 0.5 | no route | Accelerator pedal ground (SG3) | — | |
| W23 | OEM-F-2 | SP-0V-1 | 0.5 | no route | Sensor ground (SG1) | — | |
| W24 | SP-0V-1 | M130-B-15 | 0.5 | no route | Sensor 0V A | — | |
| W25 | SP-0V-1 | M130-B-16 | 0.5 | no route | Sensor 0V B | — | |
| W26 | OEM-D-10 | SP-5V1-1 | 0.5 | no route | Sensor 5V supply (VCC2) | — | |
| W27 | OEM-F-1 | SP-5V1-1 | 0.5 | no route | Sensor 5V supply (VCC1) | — | |
| W28 | SP-5V1-1 | M130-A-9 | 0.5 | no route | Sensor 5.0V B | — | |
| W29 | OEM-F-14 | M130-A-2 | 0.5 | no route | Accelerator pedal 5V supply (VCC3) | — | |
| W30 | OEM-B-8 | M130-B-1 | 0.5 | no route | Crank position sensor 1 + (CKP 1P) | — | |
| W31 | OEM-B-7 | M130-B-2 | 0.5 | no route | Crank position sensor 2 + (CKP 2P) | — | |
| W32 | OEM-B-6 | M130-B-8 | 0.5 | no route | Cylinder position sensor 1 + (CYP 1P) | — | |
| W33 | OEM-B-5 | M130-B-9 | 0.5 | no route | Cylinder position sensor 2 + (CYP 2P) | — | |
| W34 | OEM-D-13 | M130-B-7 | 0.5 | no route | Knock sensor front (KSF) | — | |
| W35 | OEM-D-2 | M130-B-13 | 0.5 | no route | Knock sensor rear (KSR) | — | |
| W36 | OEM-A-11 | M130-A-3 | 0.5 | no route | Ignition coil 1 (IGN COIL1) | — | |
| W37 | OEM-A-24 | M130-A-4 | 0.5 | no route | Ignition coil 2 (IGN COIL2) | — | |
| W38 | OEM-B-12 | M130-A-5 | 0.5 | no route | Ignition coil 3 (IGN COIL3) | — | |
| W39 | OEM-B-11 | M130-A-6 | 0.5 | no route | Ignition coil 4 (IGN COIL4) | — | |
| W40 | OEM-B-10 | M130-A-7 | 0.5 | no route | Ignition coil 5 (IGN COIL5) | — | |
| W41 | OEM-B-2 | M130-A-8 | 0.5 | no route | Ignition coil 6 (IGN COIL6) | — | |
| W42 | OEM-A-1 | M130-A-19 | 0.5 | no route | Injector 1 (INJ1) | — | |
| W43 | OEM-A-2 | M130-A-23 | 0.5 | no route | Injector 2 (INJ2) | — | |
| W44 | OEM-A-3 | M130-A-20 | 0.5 | no route | Injector 3 (INJ3) | — | |
| W45 | OEM-A-14 | M130-A-24 | 0.5 | no route | Injector 4 (INJ4) | — | |
| W46 | OEM-A-15 | M130-A-21 | 0.5 | no route | Injector 5 (INJ5) | — | |
| W47 | OEM-A-16 | M130-A-22 | 0.5 | no route | Injector 6 (INJ6) | — | |
| W48 | OEM-A-5 | M130-A-27 | 0.5 | no route | Fuel pump relay (FLR1) | — | |
| W49 | OEM-F-19 | M130-A-28 | 0.5 | no route | VTEC solenoid front (VT SOLF) | — | |
| W50 | OEM-F-20 | M130-A-29 | 0.5 | no route | VTEC solenoid rear (VT SOLR) | — | |
| W51 | OEM-D-9 | M130-A-14 | 0.5 | no route | MAP sensor | — | |
| W52 | OEM-F-13 | M130-A-15 | 0.5 | no route | Accelerator pedal position 1 (AP1) | — | |
| W53 | OEM-F-12 | M130-A-16 | 0.5 | no route | Accelerator pedal position 2 (AP2) | — | |
| W54 | OEM-D-12 | M130-A-17 | 0.5 | no route | Throttle position sensor (TPS) | — | |
| W55 | OEM-D-7 | M130-B-3 | 0.5 | no route | Engine coolant temperature (ECT) | — | |
| W56 | OEM-F-4 | M130-A-30 | 0.5 | no route | Fuel pump relay 2 (FLR2) | — | |
| W57 | OEM-D-16 | M130-A-25 | 0.5 | no route | Front secondary O2 signal (O2S FS) | — | |
| W58 | OEM-D-17 | M130-B-20 | 0.5 | no route | Rear secondary O2 signal (O2S RS) | — | |
| W59 | OEM-D-18 | M130-B-21 | 0.5 | no route | Front primary O2 signal (O2S FP) | — | |
| W60 | OEM-D-19 | M130-B-22 | 0.5 | no route | Rear primary O2 signal (O2S RP) | — | |
| W61 | OEM-D-8 | M130-B-4 | 0.5 | no route | Intake air temperature (IAT) | — | |
| W62 | OEM-C-7 | M130-B-10 | 0.5 | no route | Vehicle speed sensor (VSS) | — | |
| W63 | OEM-F-16 | M130-B-11 | 0.5 | no route | Brake switch 1 (BKSW1) | — | |
| W64 | OEM-F-6 | M130-B-14 | 0.5 | no route | Brake switch 2 (BKSW2) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (14)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | DBW_SENSOR_INPUT | tps | Only 0 throttle-position track(s) found. An electronic throttle needs two (main and sub) so the ECU can cross-check them. |
| error | REQUIRED_UNMAPPED | OEM-G-11 | Required OEM function "Throttle motor phase 3 (PM3)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-G-12 | Required OEM function "Throttle motor phase 4 (PM4)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-G-4 | Required OEM function "Throttle motor phase 1 (PM1)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-G-5 | Required OEM function "Throttle motor phase 2 (PM2)" (hbridge_out) is not connected to the new ECU. |
| warn | NET_FAMILY | OEM-B-5 ↔ M130-B-9 | OEM-B-5 "Cylinder position sensor 2 + (CYP 2P)" [trigger_in] is wired to M130-B-9 "Universal Digital Input 4" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| warn | NET_FAMILY | OEM-B-6 ↔ M130-B-8 | OEM-B-6 "Cylinder position sensor 1 + (CYP 1P)" [trigger_in] is wired to M130-B-8 "Universal Digital Input 3" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| warn | NET_FAMILY | OEM-B-7 ↔ M130-B-2 | OEM-B-7 "Crank position sensor 2 + (CKP 2P)" [trigger_in] is wired to M130-B-2 "Universal Digital Input 2" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| warn | NET_FAMILY | OEM-B-8 ↔ M130-B-1 | OEM-B-8 "Crank position sensor 1 + (CKP 1P)" [trigger_in] is wired to M130-B-1 "Universal Digital Input 1" [digital_in]. Hall-type cam/speed signals can use a digital input if it handles the frequency; VR signals cannot. |
| info | NET_FAMILY | OEM-A-5 ↔ M130-A-27 | OEM-A-5 "Fuel pump relay (FLR1)" [low_side_out] is wired to M130-A-27 "Peak Hold Injector 5" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-F-19 ↔ M130-A-28 | OEM-F-19 "VTEC solenoid front (VT SOLF)" [low_side_out] is wired to M130-A-28 "Peak Hold Injector 6" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-F-20 ↔ M130-A-29 | OEM-F-20 "VTEC solenoid rear (VT SOLR)" [low_side_out] is wired to M130-A-29 "Peak Hold Injector 7" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-F-4 ↔ M130-A-30 | OEM-F-4 "Fuel pump relay 2 (FLR2)" [low_side_out] is wired to M130-A-30 "Peak Hold Injector 8" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | UNMAPPED | OEM | 19 optional OEM pins are not mapped: OEM-A-10 Rear secondary O2 heater (RSO2SHTC); OEM-A-17 EVAP bypass solenoid (2WBS); OEM-A-20 IAB control solenoid (IABCS); OEM-A-21 EVAP purge control solenoid (PCS); OEM-A-22 Front primary O2 heater (FPO2SHTC); OEM-A-23 Rear primary O2 heater (RPO2SHTC); OEM-A-4 EVAP canister vent shut valve (VSV); OEM-A-6 EGR control solenoid (ESOL); OEM-A-7 Malfunction indicator lamp (MIL); OEM-A-8 A/C clutch relay (ACC); OEM-A-9 Front secondary O2 heater (FSO2SHTC); OEM-B-1 VTEC pressure switch front (VTP SWF); OEM-B-3 VTEC pressure switch rear (VTP SWR); OEM-B-4 Neutral switch (NT SW, M/T); OEM-C-4 Clutch switch (MTCLS, M/T); OEM-C-6 Starter switch (STS); OEM-C-8 Engine speed pulse (NEP); OEM-D-20 EGR valve lift sensor (EGRL); OEM-D-4 K-line diagnostics |
Accepted (0)
| Code | Subject | Reason | By |
|---|
Notes
Fit check: unconfirmed. Confirm these before building: - Trigger pattern for Honda C32B not found in the ECU's docs (M150 engine-speed modes (datasheet 23514) list CBR250RR/F20C/J35A/K20/K20C1/K24AZ7/L15B7 — no C30A/C32B/NSX) - This car has Honda Type 1A (1997+) immobilizer; needs a delete/bypass Auto-mapped by auto_map() from the library pin data on 2026-10-11. Review every wire against both manuals before building. Open items: - OEM-G 4: Throttle motor phase 1 (PM1): no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-G 5: Throttle motor phase 2 (PM2): no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-G 11: Throttle motor phase 3 (PM3): no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-G 12: Throttle motor phase 4 (PM4): no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand Not wired: - OEM-A 8: A/C clutch relay (ACC): no free relay_control/low_side/heater_low_side/ls_hs/injector rated ≥ 0.2 A on MoTeC M130 - OEM-A 10: Rear secondary O2 heater (RSO2SHTC): no free heater_low_side/low_side/relay_control/ls_hs/injector on MoTeC M130 - OEM-A 22: Front primary O2 heater (FPO2SHTC): no free heater_low_side/low_side/relay_control/ls_hs/injector on MoTeC M130 - OEM-A 23: Rear primary O2 heater (RPO2SHTC): no free heater_low_side/low_side/relay_control/ls_hs/injector on MoTeC M130 - OEM-A 9: Front secondary O2 heater (FSO2SHTC): no free heater_low_side/low_side/relay_control/ls_hs/injector on MoTeC M130 - OEM-A 17: EVAP bypass solenoid (2WBS): no free low_side/relay_control/heater_low_side/ls_hs/injector on MoTeC M130 - OEM-A 20: IAB control solenoid (IABCS): no free low_side/relay_control/heater_low_side/ls_hs/injector on MoTeC M130 - OEM-A 21: EVAP purge control solenoid (PCS): no free low_side/relay_control/heater_low_side/ls_hs/injector on MoTeC M130 - OEM-A 4: EVAP canister vent shut valve (VSV): no free low_side/relay_control/heater_low_side/ls_hs/injector on MoTeC M130 - OEM-A 6: EGR control solenoid (ESOL): no free low_side/relay_control/heater_low_side/ls_hs/injector on MoTeC M130 - OEM-A 7: Malfunction indicator lamp (MIL): no free low_side/relay_control/heater_low_side/ls_hs/injector on MoTeC M130 - OEM-C 8: Engine speed pulse (NEP): no free tacho/frequency_out/low_side/ls_hs on MoTeC M130 - OEM-D 20: EGR valve lift sensor (EGRL): no free analog_0_5 on MoTeC M130 - OEM-B 1: VTEC pressure switch front (VTP SWF): no free switch_in/frequency_in/analog_0_5 on MoTeC M130 - OEM-B 3: VTEC pressure switch rear (VTP SWR): no free switch_in/frequency_in/analog_0_5 on MoTeC M130 - OEM-B 4: Neutral switch (NT SW, M/T): no free switch_in/frequency_in/analog_0_5 on MoTeC M130 - OEM-C 4: Clutch switch (MTCLS, M/T): no free switch_in/frequency_in/analog_0_5 on MoTeC M130 - OEM-C 6: Starter switch (STS): no free switch_in/frequency_in/analog_0_5 on MoTeC M130 - OEM-D 4: K-line diagnostics: no free k_line on MoTeC M130
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | 1997-2005 Acura NSX Service Manual §11 (PGM-FI), ECM terminal arrangement | https://www.manualslib.com/manual/1540331/Acura-Nsx-1997.html | — | — | — |
| 4 | vendor_doc | MoTeC: M1 ECU Hardware manual (7 Nov 2013) — M130/M150/M170/M190 pinout tables | https://web.archive.org/web/2023id_/https://www.motec.com.au/hessian/uploads/M1_ECU_Hardware_c2517380e4.pdf | — | 2026-10-05 | 03dc5975f739 |