Lexus IS300 (XE10 / JCE10) 2001-05 2JZ-GE VVT-i → Link G5 Voodoo Pro V1 (auto)
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 8: read the Findings page before cutting any wire |
| Size of the job | 51 wires · 10 connectors · 0 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-E6-17 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-E7-21 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | OEM-E6-2 | G5VOODOOPROV-A-A32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | OEM-E7-23 | G5VOODOOPROV-A-A8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-E7-10 | G5VOODOOPROV-A-A9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-E7-28 | G5VOODOOPROV-B-B9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-E7-27 | G5VOODOOPROV-B-B8 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | OEM-E7-11 | G5VOODOOPROV-A-A13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | OEM-E7-12 | G5VOODOOPROV-A-A12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | OEM-E7-13 | G5VOODOOPROV-A-A11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | OEM-E6-5 | G5VOODOOPROV-A-A4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | OEM-E6-6 | G5VOODOOPROV-A-A3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | OEM-E7-1 | G5VOODOOPROV-A-A2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-E7-2 | G5VOODOOPROV-A-A1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-E7-3 | G5VOODOOPROV-B-B4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-E7-4 | G5VOODOOPROV-B-B3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | OEM-E3-9 | G5VOODOOPROV-A-A6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | OEM-E7-17 | G5VOODOOPROV-A-A21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | OEM-E7-18 | G5VOODOOPROV-A-A20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | OEM-E7-19 | G5VOODOOPROV-A-A19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-E7-20 | G5VOODOOPROV-A-A18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-E6-15 | G5VOODOOPROV-A-A17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-E6-23 | G5VOODOOPROV-A-A22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-E6-16 | G5VOODOOPROV-A-A33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-E6-24 | G5VOODOOPROV-A-A14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-E6-14 | G5VOODOOPROV-A-A15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-E3-10 | G5VOODOOPROV-E-E15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-E3-4 | G5VOODOOPROV-E-E22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-E4-13 | G5VOODOOPROV-A-A29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-E2-25 | G5VOODOOPROV-A-A28 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-E2-26 | G5VOODOOPROV-A-A27 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-E6-3 | G5VOODOOPROV-A-A26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-E6-4 | G5VOODOOPROV-B-B2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-E3-5 | G5VOODOOPROV-B-B1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-E3-6 | G5VOODOOPROV-E-E4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-E5-12 | G5VOODOOPROV-E-E3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-E6-7 | G5VOODOOPROV-E-E2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-E7-5 | G5VOODOOPROV-E-E1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-E6-10 | G5VOODOOPROV-B-B33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-E2-24 | G5VOODOOPROV-B-B15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-E4-8 | G5VOODOOPROV-B-B16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-E6-11 | G5VOODOOPROV-B-B23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-E6-12 | G5VOODOOPROV-B-B24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-E6-22 | G5VOODOOPROV-A-A16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-E4-18 | G5VOODOOPROV-B-B31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-E5-11 | G5VOODOOPROV-A-A30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | OEM-E5-5 | G5VOODOOPROV-A-A31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | OEM-E7-25 | G5VOODOOPROV-A-A23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W49 | OEM-E4-2 | G5VOODOOPROV-B-B21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W50 | OEM-E4-5 | G5VOODOOPROV-B-B20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W51 | OEM-E4-6 | G5VOODOOPROV-B-B19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | OEM-E6-17 | G5VOODOOPROV-A-A32 | open (OL) | power ground must not touch 5 V sensor reference |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
G5VOODOOPROV-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| A1 | Injection 4 | — | W14 | — | 0.5 | OEM-E7-2 | — | — | — |
| A10 | Ignition 4 | — | — | — | — | — | — | — | — |
| A11 | Ignition 3 | — | W10 | — | 0.5 | OEM-E7-13 | — | — | — |
| A12 | Ignition 2 | — | W9 | — | 0.5 | OEM-E7-12 | — | — | — |
| A13 | Ignition 1 | — | W8 | — | 0.5 | OEM-E7-11 | — | — | — |
| A14 | Analogue Volt 4 | — | W25 | — | 0.5 | OEM-E6-24 | — | — | — |
| A15 | Analogue Temp 1 | — | W26 | — | 0.5 | OEM-E6-14 | — | — | — |
| A16 | Analogue Temp 2 | — | W44 | — | 0.5 | OEM-E6-22 | — | — | — |
| A17 | Analogue Volt 1 | — | W22 | — | 0.5 | OEM-E6-15 | — | — | — |
| A18 | Aux 4 | — | W21 | — | 0.5 | OEM-E7-20 | — | — | — |
| A19 | Aux 3 | — | W20 | — | 0.5 | OEM-E7-19 | — | — | — |
| A2 | Injection 3 | — | W13 | — | 0.5 | OEM-E7-1 | — | — | — |
| A20 | Aux 2 | — | W19 | — | 0.5 | OEM-E7-18 | — | — | — |
| A21 | Aux 1 | — | W18 | — | 0.5 | OEM-E7-17 | — | — | — |
| A22 | Analogue Volt 2 | — | W23 | — | 0.5 | OEM-E6-23 | — | — | — |
| A23 | Digital Input 3 | — | W48 | — | 0.5 | OEM-E7-25 | — | — | — |
| A26 | Aux 8 | — | W32 | — | 0.5 | OEM-E6-3 | — | — | — |
| A27 | Aux 7 | — | W31 | — | 0.5 | OEM-E2-26 | — | — | — |
| A28 | Aux 6 | — | W30 | — | 0.5 | OEM-E2-25 | — | — | — |
| A29 | Aux 5 | — | W29 | — | 0.5 | OEM-E4-13 | — | — | — |
| A3 | Injection 2 | — | W12 | — | 0.5 | OEM-E6-6 | — | — | — |
| A30 | Digital Input 1 | — | W46 | — | 0.5 | OEM-E5-11 | — | — | — |
| A31 | Digital Input 2 | — | W47 | — | 0.5 | OEM-E5-5 | — | — | — |
| A32 | +5V Out | — | W3 | — | 0.5 | OEM-E6-2 | — | — | — |
| A33 | Analogue Volt 3 | — | W24 | — | 0.5 | OEM-E6-16 | — | — | — |
| A4 | Injection 1 | — | W11 | — | 0.5 | OEM-E6-5 | — | — | — |
| A6 | Ignition Switch | — | W17 | — | 0.5 | OEM-E3-9 | — | — | — |
| A8 | Trigger 1 | — | W4 | — | 0.5 | OEM-E7-23 | — | — | — |
| A9 | Trigger 2 | — | W5 | — | 0.5 | OEM-E7-10 | — | — | — |
G5VOODOOPROV-B
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| B1 | Injection 8 | — | W34 | — | 0.5 | OEM-E3-5 | — | — | — |
| B10 | Ignition 8 | — | — | — | — | — | — | — | — |
| B11 | Ignition 7 | — | — | — | — | — | — | — | — |
| B12 | Ignition 6 | — | — | — | — | — | — | — | — |
| B13 | Ignition 5 | — | — | — | — | — | — | — | — |
| B14 | Analogue Volt 14 | — | — | — | — | — | — | — | — |
| B15 | Analogue Volt 6 | — | W40 | — | 0.5 | OEM-E2-24 | — | — | — |
| B16 | Analogue Volt 7 | — | W41 | — | 0.5 | OEM-E4-8 | — | — | — |
| B18 | Aux 9 | — | — | — | — | — | — | — | — |
| B19 | Digital Input 6 | — | W51 | — | 0.5 | OEM-E4-6 | — | — | — |
| B2 | Injection 7 | — | W33 | — | 0.5 | OEM-E6-4 | — | — | — |
| B20 | Digital Input 5 | — | W50 | — | 0.5 | OEM-E4-5 | — | — | — |
| B21 | Digital Input 4 | — | W49 | — | 0.5 | OEM-E4-2 | — | — | — |
| B23 | Analogue Volt 8 | — | W42 | — | 0.5 | OEM-E6-11 | — | — | — |
| B24 | Analogue Volt 9 | — | W43 | — | 0.5 | OEM-E6-12 | — | — | — |
| B26 | Aux 10 | — | — | — | — | — | — | — | — |
| B27 | Digital Input 10 | — | — | — | — | — | — | — | — |
| B28 | Digital Input 9 | — | — | — | — | — | — | — | — |
| B29 | Digital Input 8 | — | — | — | — | — | — | — | — |
| B3 | Injection 6 | — | W16 | — | 0.5 | OEM-E7-4 | — | — | — |
| B30 | Digital Input 7 | — | — | — | — | — | — | — | — |
| B31 | Analogue Volt 10 | — | W45 | — | 0.5 | OEM-E4-18 | — | — | — |
| B32 | Analogue Volt 11 | — | — | — | — | — | — | — | — |
| B33 | Analogue Volt 5 | — | W39 | — | 0.5 | OEM-E6-10 | — | — | — |
| B4 | Injection 5 | — | W15 | — | 0.5 | OEM-E7-3 | — | — | — |
| B6 | Analogue Temp 3 | — | — | — | — | — | — | — | — |
| B7 | Analogue Temp 4 | — | — | — | — | — | — | — | — |
| B8 | Knock 2 | — | W7 | — | 0.5 | OEM-E7-27 | — | — | — |
| B9 | Knock 1 | — | W6 | — | 0.5 | OEM-E7-28 | — | — | — |
G5VOODOOPROV-E
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| E1 | Injection 12 | — | W38 | — | 0.5 | OEM-E7-5 | — | — | — |
| E10 | Injection 14 / Ignition 10 | — | — | — | — | — | — | — | — |
| E11 | Injection 13 / Ignition 9 | — | — | — | — | — | — | — | — |
| E12 | Analogue Volt 12 | — | — | — | — | — | — | — | — |
| E13 | Analogue Volt 13 | — | — | — | — | — | — | — | — |
| E14 | Aux 11 | — | — | — | — | — | — | — | — |
| E15 | Aux 13 / WB Heater 1 | — | W27 | — | 0.5 | OEM-E3-10 | — | — | — |
| E16 | RE 1 | — | — | — | — | — | — | — | — |
| E17 | IPE 1 | — | — | — | — | — | — | — | — |
| E18 | APE 1 | — | — | — | — | — | — | — | — |
| E19 | MES 1 | — | — | — | — | — | — | — | — |
| E2 | Injection 11 | — | W37 | — | 0.5 | OEM-E6-7 | — | — | — |
| E20 | Aux 12 | — | — | — | — | — | — | — | — |
| E22 | Aux 14 / WB Heater 2 | — | W28 | — | 0.5 | OEM-E3-4 | — | — | — |
| E23 | RE 2 | — | — | — | — | — | — | — | — |
| E24 | IPE 2 | — | — | — | — | — | — | — | — |
| E25 | APE 2 | — | — | — | — | — | — | — | — |
| E26 | MES 2 | — | — | — | — | — | — | — | — |
| E3 | Injection 10 | — | W36 | — | 0.5 | OEM-E5-12 | — | — | — |
| E4 | Injection 9 | — | W35 | — | 0.5 | OEM-E3-6 | — | — | — |
| E8 | Injection 16 / Ignition 12 | — | — | — | — | — | — | — | — |
| E9 | Injection 15 / Ignition 11 | — | — | — | — | — | — | — | — |
OEM-E2
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 13 | ETCS power (TBP, throttle bypass) | — | — | — | — | — | — | — | — |
| 24 | O2 right rear (OXR2) | — | W40 | — | 0.5 | G5VOODOOPROV-B-B15 | — | — | — |
| 25 | O2 heater right rear (HTR2) | — | W30 | — | 0.5 | G5VOODOOPROV-A-A28 | — | — | — |
| 26 | O2 heater left rear (HTL2) | — | W31 | — | 0.5 | G5VOODOOPROV-A-A27 | — | — | — |
OEM-E3
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Battery constant (BATT) | — | — | — | — | — | — | — | — |
| 10 | EFI main relay control (MREL) | — | W27 | — | 0.5 | G5VOODOOPROV-E-E15 | — | — | — |
| 11 | Serial diagnostic (SIL) | — | — | — | — | — | — | — | — |
| 16 | EFI main relay (+B) | — | — | — | — | — | — | — | — |
| 4 | Fuel pump relay (FPR) | — | W28 | — | 0.5 | G5VOODOOPROV-E-E22 | — | — | — |
| 5 | Fuel pump control (FC) | — | W34 | — | 0.5 | G5VOODOOPROV-B-B1 | — | — | — |
| 6 | Check-engine lamp (W) | — | W35 | — | 0.5 | G5VOODOOPROV-E-E4 | — | — | — |
| 7 | ETCS main relay (+BM) | — | — | — | — | — | — | — | — |
| 8 | EFI main relay (+B2) | — | — | — | — | — | — | — | — |
| 9 | Ignition switch (IGSW) | — | W17 | — | 0.5 | G5VOODOOPROV-A-A6 | — | — | — |
OEM-E4
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 13 | A/C clutch relay (ACMG) | — | W29 | — | 0.5 | G5VOODOOPROV-A-A29 | — | — | — |
| 18 | EVAP vapor pressure (PTNK) | — | W45 | — | 0.5 | G5VOODOOPROV-B-B31 | — | — | — |
| 2 | Starter signal (STA) | — | W49 | — | 0.5 | G5VOODOOPROV-B-B21 | — | — | — |
| 5 | Diagnostic/timing check (TC) | — | W50 | — | 0.5 | G5VOODOOPROV-B-B20 | — | — | — |
| 6 | Stop light switch (STP) | — | W51 | — | 0.5 | G5VOODOOPROV-B-B19 | — | — | — |
| 8 | O2 left rear (OXL2) | — | W41 | — | 0.5 | G5VOODOOPROV-B-B16 | — | — | — |
OEM-E5
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 11 | Vehicle speed sensor (SP2-) | — | W46 | — | 0.5 | G5VOODOOPROV-A-A30 | — | — | — |
| 12 | Canister close valve (CCV) | — | W36 | — | 0.5 | G5VOODOOPROV-E-E3 | — | — | — |
| 5 | Vehicle speed sensor (SP2+) | — | W47 | — | 0.5 | G5VOODOOPROV-A-A31 | — | — | — |
OEM-E6
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 10 | Mass air flow (VG) | — | W39 | — | 0.5 | G5VOODOOPROV-B-B33 | — | — | — |
| 11 | O2 right front (OXR1) | — | W42 | — | 0.5 | G5VOODOOPROV-B-B23 | — | — | — |
| 12 | O2 left front (OXL1) | — | W43 | — | 0.5 | G5VOODOOPROV-B-B24 | — | — | — |
| 14 | Coolant temperature (THW) | — | W26 | — | 0.5 | G5VOODOOPROV-A-A15 | — | — | — |
| 15 | Accelerator pedal 1 (VPA) | — | W22 | — | 0.5 | G5VOODOOPROV-A-A17 | — | — | — |
| 16 | Accelerator pedal 2 (VPA2) | — | W24 | — | 0.5 | G5VOODOOPROV-A-A33 | — | — | — |
| 17 | Power ground (E1) | — | W1 | — | 0.85 | SP-GND-1 | — | — | — |
| 18 | Sensor ground (E2) | — | — | — | — | — | — | — | — |
| 19 | MAF ground (EVG) | — | — | — | — | — | — | — | — |
| 2 | Sensor supply +5V (VC) | — | W3 | — | 0.5 | G5VOODOOPROV-A-A32 | — | — | — |
| 22 | Intake air temperature (THA) | — | W44 | — | 0.5 | G5VOODOOPROV-A-A16 | — | — | — |
| 23 | Throttle position 1 (VTA) | — | W23 | — | 0.5 | G5VOODOOPROV-A-A22 | — | — | — |
| 24 | Throttle position 2 (VTA2) | — | W25 | — | 0.5 | G5VOODOOPROV-A-A14 | — | — | — |
| 3 | O2 heater right front (HTR) | — | W32 | — | 0.5 | G5VOODOOPROV-A-A26 | — | — | — |
| 4 | O2 heater left front (HTL) | — | W33 | — | 0.5 | G5VOODOOPROV-B-B2 | — | — | — |
| 5 | Injector 1 (#10) | — | W11 | — | 0.5 | G5VOODOOPROV-A-A4 | — | — | — |
| 6 | Injector 2 (#20) | — | W12 | — | 0.5 | G5VOODOOPROV-A-A3 | — | — | — |
| 7 | EVAP purge VSV (PRG) | — | W37 | — | 0.5 | G5VOODOOPROV-E-E2 | — | — | — |
OEM-E7
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector 3 (#30) | — | W13 | — | 0.5 | G5VOODOOPROV-A-A2 | — | — | — |
| 10 | Cam position (G2) | — | W5 | — | 0.5 | G5VOODOOPROV-A-A9 | — | — | — |
| 11 | Ignition 1 (IGT) | — | W8 | — | 0.5 | G5VOODOOPROV-A-A13 | — | — | — |
| 12 | Ignition 2 (IGT2) | — | W9 | — | 0.5 | G5VOODOOPROV-A-A12 | — | — | — |
| 13 | Ignition 3 (IGT3) | — | W10 | — | 0.5 | G5VOODOOPROV-A-A11 | — | — | — |
| 17 | VVT-i OCV - (OCV-) | — | W18 | — | 0.5 | G5VOODOOPROV-A-A21 | — | — | — |
| 18 | VVT-i OCV + (OCV+) | — | W19 | — | 0.5 | G5VOODOOPROV-A-A20 | — | — | — |
| 19 | ETCS throttle clutch - (CL-) | — | W20 | — | 0.5 | G5VOODOOPROV-A-A19 | — | — | — |
| 2 | Injector 4 (#40) | — | W14 | — | 0.5 | G5VOODOOPROV-A-A1 | — | — | — |
| 20 | ETCS throttle clutch + (CL+) | — | W21 | — | 0.5 | G5VOODOOPROV-A-A18 | — | — | — |
| 21 | Power ground (E01) | — | W2 | — | 0.85 | SP-GND-1 | — | — | — |
| 22 | Crank position return (NE-) | — | — | — | — | — | — | — | — |
| 23 | Crank position (NE) | — | W4 | — | 0.5 | G5VOODOOPROV-A-A8 | — | — | — |
| 25 | Igniter feedback (IGF) | — | W48 | — | 0.5 | G5VOODOOPROV-A-A23 | — | — | — |
| 27 | Knock sensor 2 (KNK2) | — | W7 | — | 0.5 | G5VOODOOPROV-B-B8 | — | — | — |
| 28 | Knock sensor 1 (KNK1) | — | W6 | — | 0.5 | G5VOODOOPROV-B-B9 | — | — | — |
| 3 | Injector 5 (#50) | — | W15 | — | 0.5 | G5VOODOOPROV-B-B4 | — | — | — |
| 4 | Injector 6 (#60) | — | W16 | — | 0.5 | G5VOODOOPROV-B-B3 | — | — | — |
| 5 | ACIS intake VSV | — | W38 | — | 0.5 | G5VOODOOPROV-E-E1 | — | — | — |
| 7 | ETCS throttle motor - (M-) | — | — | — | — | — | — | — | — |
| 8 | ETCS throttle motor + (M+) | — | — | — | — | — | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-E6-17 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-E7-21 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-E2-13 | ETCS power (TBP, throttle bypass) | power_in | — | — | — | single_source | |
| OEM-E2-24 | O2 right rear (OXR2) | lambda_nb_in | G5VOODOOPROV-B-B15 | Analogue Volt 6 | analog_in | single_source | |
| OEM-E2-25 | O2 heater right rear (HTR2) | low_side_out | G5VOODOOPROV-A-A28 | Aux 6 | switch_out | single_source | |
| OEM-E2-26 | O2 heater left rear (HTL2) | low_side_out | G5VOODOOPROV-A-A27 | Aux 7 | switch_out | single_source | |
| OEM-E3-1 | Battery constant (BATT) | power_in | — | — | — | single_source | |
| OEM-E3-10 | EFI main relay control (MREL) | low_side_out | G5VOODOOPROV-E-E15 | Aux 13 / WB Heater 1 | low_side_out | single_source | |
| OEM-E3-11 | Serial diagnostic (SIL) | serial | — | — | — | single_source | |
| OEM-E3-16 | EFI main relay (+B) | power_in | — | — | — | single_source | |
| OEM-E3-4 | Fuel pump relay (FPR) | low_side_out | G5VOODOOPROV-E-E22 | Aux 14 / WB Heater 2 | low_side_out | single_source | |
| OEM-E3-5 | Fuel pump control (FC) | low_side_out | G5VOODOOPROV-B-B1 | Injection 8 | injector_out | single_source | |
| OEM-E3-6 | Check-engine lamp (W) | low_side_out | G5VOODOOPROV-E-E4 | Injection 9 | injector_out | single_source | |
| OEM-E3-7 | ETCS main relay (+BM) | power_in | — | — | — | single_source | |
| OEM-E3-8 | EFI main relay (+B2) | power_in | — | — | — | single_source | |
| OEM-E3-9 | Ignition switch (IGSW) | digital_in | G5VOODOOPROV-A-A6 | Ignition Switch | digital_in | single_source | |
| OEM-E4-13 | A/C clutch relay (ACMG) | low_side_out | G5VOODOOPROV-A-A29 | Aux 5 | switch_out | single_source | |
| OEM-E4-18 | EVAP vapor pressure (PTNK) | analog_in | G5VOODOOPROV-B-B31 | Analogue Volt 10 | analog_in | single_source | |
| OEM-E4-2 | Starter signal (STA) | digital_in | G5VOODOOPROV-B-B21 | Digital Input 4 | digital_in | single_source | |
| OEM-E4-5 | Diagnostic/timing check (TC) | digital_in | G5VOODOOPROV-B-B20 | Digital Input 5 | digital_in | single_source | |
| OEM-E4-6 | Stop light switch (STP) | digital_in | G5VOODOOPROV-B-B19 | Digital Input 6 | digital_in | single_source | |
| OEM-E4-8 | O2 left rear (OXL2) | lambda_nb_in | G5VOODOOPROV-B-B16 | Analogue Volt 7 | analog_in | single_source | |
| OEM-E5-11 | Vehicle speed sensor (SP2-) | digital_in | G5VOODOOPROV-A-A30 | Digital Input 1 | digital_in | single_source | |
| OEM-E5-12 | Canister close valve (CCV) | low_side_out | G5VOODOOPROV-E-E3 | Injection 10 | injector_out | single_source | |
| OEM-E5-5 | Vehicle speed sensor (SP2+) | digital_in | G5VOODOOPROV-A-A31 | Digital Input 2 | digital_in | single_source | |
| OEM-E6-10 | Mass air flow (VG) | analog_in | G5VOODOOPROV-B-B33 | Analogue Volt 5 | analog_in | single_source | |
| OEM-E6-11 | O2 right front (OXR1) | lambda_nb_in | G5VOODOOPROV-B-B23 | Analogue Volt 8 | analog_in | single_source | |
| OEM-E6-12 | O2 left front (OXL1) | lambda_nb_in | G5VOODOOPROV-B-B24 | Analogue Volt 9 | analog_in | single_source | |
| OEM-E6-14 | Coolant temperature (THW) | temp_in | G5VOODOOPROV-A-A15 | Analogue Temp 1 | temp_in | single_source | |
| OEM-E6-15 | Accelerator pedal 1 (VPA) | analog_in | G5VOODOOPROV-A-A17 | Analogue Volt 1 | analog_in | single_source | |
| OEM-E6-16 | Accelerator pedal 2 (VPA2) | analog_in | G5VOODOOPROV-A-A33 | Analogue Volt 3 | analog_in | single_source | |
| OEM-E6-17 | Power ground (E1) | ground | — | — | — | single_source | |
| OEM-E6-18 | Sensor ground (E2) | sensor_ground | — | — | — | single_source | |
| OEM-E6-19 | MAF ground (EVG) | sensor_ground | — | — | — | single_source | |
| OEM-E6-2 | Sensor supply +5V (VC) | vref | G5VOODOOPROV-A-A32 | +5V Out | vref | single_source | |
| OEM-E6-22 | Intake air temperature (THA) | temp_in | G5VOODOOPROV-A-A16 | Analogue Temp 2 | temp_in | single_source | |
| OEM-E6-23 | Throttle position 1 (VTA) | analog_in | G5VOODOOPROV-A-A22 | Analogue Volt 2 | analog_in | single_source | |
| OEM-E6-24 | Throttle position 2 (VTA2) | analog_in | G5VOODOOPROV-A-A14 | Analogue Volt 4 | analog_in | single_source | |
| OEM-E6-3 | O2 heater right front (HTR) | low_side_out | G5VOODOOPROV-A-A26 | Aux 8 | switch_out | single_source | |
| OEM-E6-4 | O2 heater left front (HTL) | low_side_out | G5VOODOOPROV-B-B2 | Injection 7 | injector_out | single_source | |
| OEM-E6-5 | Injector 1 (#10) | injector_out | G5VOODOOPROV-A-A4 | Injection 1 | injector_out | single_source | |
| OEM-E6-6 | Injector 2 (#20) | injector_out | G5VOODOOPROV-A-A3 | Injection 2 | injector_out | single_source | |
| OEM-E6-7 | EVAP purge VSV (PRG) | low_side_out | G5VOODOOPROV-E-E2 | Injection 11 | injector_out | single_source | |
| OEM-E7-1 | Injector 3 (#30) | injector_out | G5VOODOOPROV-A-A2 | Injection 3 | injector_out | single_source | |
| OEM-E7-10 | Cam position (G2) | trigger_in | G5VOODOOPROV-A-A9 | Trigger 2 | trigger_in | single_source | |
| OEM-E7-11 | Ignition 1 (IGT) | ignition_out | G5VOODOOPROV-A-A13 | Ignition 1 | ignition_out | single_source | |
| OEM-E7-12 | Ignition 2 (IGT2) | ignition_out | G5VOODOOPROV-A-A12 | Ignition 2 | ignition_out | single_source | |
| OEM-E7-13 | Ignition 3 (IGT3) | ignition_out | G5VOODOOPROV-A-A11 | Ignition 3 | ignition_out | single_source | |
| OEM-E7-17 | VVT-i OCV - (OCV-) | low_side_out | G5VOODOOPROV-A-A21 | Aux 1 | low_side_out | single_source | |
| OEM-E7-18 | VVT-i OCV + (OCV+) | low_side_out | G5VOODOOPROV-A-A20 | Aux 2 | low_side_out | single_source | |
| OEM-E7-19 | ETCS throttle clutch - (CL-) | low_side_out | G5VOODOOPROV-A-A19 | Aux 3 | low_side_out | single_source | |
| OEM-E7-2 | Injector 4 (#40) | injector_out | G5VOODOOPROV-A-A1 | Injection 4 | injector_out | single_source | |
| OEM-E7-20 | ETCS throttle clutch + (CL+) | low_side_out | G5VOODOOPROV-A-A18 | Aux 4 | low_side_out | single_source | |
| OEM-E7-21 | Power ground (E01) | ground | — | — | — | single_source | |
| OEM-E7-22 | Crank position return (NE-) | sensor_ground | — | — | — | single_source | |
| OEM-E7-23 | Crank position (NE) | trigger_in | G5VOODOOPROV-A-A8 | Trigger 1 | trigger_in | single_source | |
| OEM-E7-25 | Igniter feedback (IGF) | digital_in | G5VOODOOPROV-A-A23 | Digital Input 3 | digital_in | single_source | |
| OEM-E7-27 | Knock sensor 2 (KNK2) | knock_in | G5VOODOOPROV-B-B8 | Knock 2 | knock_in | single_source | |
| OEM-E7-28 | Knock sensor 1 (KNK1) | knock_in | G5VOODOOPROV-B-B9 | Knock 1 | knock_in | single_source | |
| OEM-E7-3 | Injector 5 (#50) | injector_out | G5VOODOOPROV-B-B4 | Injection 5 | injector_out | single_source | |
| OEM-E7-4 | Injector 6 (#60) | injector_out | G5VOODOOPROV-B-B3 | Injection 6 | injector_out | single_source | |
| OEM-E7-5 | ACIS intake VSV | low_side_out | G5VOODOOPROV-E-E1 | Injection 12 | injector_out | single_source | |
| OEM-E7-7 | ETCS throttle motor - (M-) | hbridge_out | — | — | — | single_source | |
| OEM-E7-8 | ETCS throttle motor + (M+) | hbridge_out | — | — | — | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-E6-17 | SP-GND-1 | 0.85 | no route | Power ground (E1) | — | |
| W2 | OEM-E7-21 | SP-GND-1 | 0.85 | no route | Power ground (E01) | — | |
| W3 | OEM-E6-2 | G5VOODOOPROV-A-A32 | 0.5 | no route | Sensor supply +5V (VC) | — | |
| W4 | OEM-E7-23 | G5VOODOOPROV-A-A8 | 0.5 | no route | Crank position (NE) | — | |
| W5 | OEM-E7-10 | G5VOODOOPROV-A-A9 | 0.5 | no route | Cam position (G2) | — | |
| W6 | OEM-E7-28 | G5VOODOOPROV-B-B9 | 0.5 | no route | Knock sensor 1 (KNK1) | — | |
| W7 | OEM-E7-27 | G5VOODOOPROV-B-B8 | 0.5 | no route | Knock sensor 2 (KNK2) | — | |
| W8 | OEM-E7-11 | G5VOODOOPROV-A-A13 | 0.5 | no route | Ignition 1 (IGT) | — | |
| W9 | OEM-E7-12 | G5VOODOOPROV-A-A12 | 0.5 | no route | Ignition 2 (IGT2) | — | |
| W10 | OEM-E7-13 | G5VOODOOPROV-A-A11 | 0.5 | no route | Ignition 3 (IGT3) | — | |
| W11 | OEM-E6-5 | G5VOODOOPROV-A-A4 | 0.5 | no route | Injector 1 (#10) | — | |
| W12 | OEM-E6-6 | G5VOODOOPROV-A-A3 | 0.5 | no route | Injector 2 (#20) | — | |
| W13 | OEM-E7-1 | G5VOODOOPROV-A-A2 | 0.5 | no route | Injector 3 (#30) | — | |
| W14 | OEM-E7-2 | G5VOODOOPROV-A-A1 | 0.5 | no route | Injector 4 (#40) | — | |
| W15 | OEM-E7-3 | G5VOODOOPROV-B-B4 | 0.5 | no route | Injector 5 (#50) | — | |
| W16 | OEM-E7-4 | G5VOODOOPROV-B-B3 | 0.5 | no route | Injector 6 (#60) | — | |
| W17 | OEM-E3-9 | G5VOODOOPROV-A-A6 | 0.5 | no route | Ignition switch (IGSW) | — | |
| W18 | OEM-E7-17 | G5VOODOOPROV-A-A21 | 0.5 | no route | VVT-i OCV - (OCV-) | — | |
| W19 | OEM-E7-18 | G5VOODOOPROV-A-A20 | 0.5 | no route | VVT-i OCV + (OCV+) | — | |
| W20 | OEM-E7-19 | G5VOODOOPROV-A-A19 | 0.5 | no route | ETCS throttle clutch - (CL-) | — | |
| W21 | OEM-E7-20 | G5VOODOOPROV-A-A18 | 0.5 | no route | ETCS throttle clutch + (CL+) | — | |
| W22 | OEM-E6-15 | G5VOODOOPROV-A-A17 | 0.5 | no route | Accelerator pedal 1 (VPA) | — | |
| W23 | OEM-E6-23 | G5VOODOOPROV-A-A22 | 0.5 | no route | Throttle position 1 (VTA) | — | |
| W24 | OEM-E6-16 | G5VOODOOPROV-A-A33 | 0.5 | no route | Accelerator pedal 2 (VPA2) | — | |
| W25 | OEM-E6-24 | G5VOODOOPROV-A-A14 | 0.5 | no route | Throttle position 2 (VTA2) | — | |
| W26 | OEM-E6-14 | G5VOODOOPROV-A-A15 | 0.5 | no route | Coolant temperature (THW) | — | |
| W27 | OEM-E3-10 | G5VOODOOPROV-E-E15 | 0.5 | no route | EFI main relay control (MREL) | — | |
| W28 | OEM-E3-4 | G5VOODOOPROV-E-E22 | 0.5 | no route | Fuel pump relay (FPR) | — | |
| W29 | OEM-E4-13 | G5VOODOOPROV-A-A29 | 0.5 | no route | A/C clutch relay (ACMG) | — | |
| W30 | OEM-E2-25 | G5VOODOOPROV-A-A28 | 0.5 | no route | O2 heater right rear (HTR2) | — | |
| W31 | OEM-E2-26 | G5VOODOOPROV-A-A27 | 0.5 | no route | O2 heater left rear (HTL2) | — | |
| W32 | OEM-E6-3 | G5VOODOOPROV-A-A26 | 0.5 | no route | O2 heater right front (HTR) | — | |
| W33 | OEM-E6-4 | G5VOODOOPROV-B-B2 | 0.5 | no route | O2 heater left front (HTL) | — | |
| W34 | OEM-E3-5 | G5VOODOOPROV-B-B1 | 0.5 | no route | Fuel pump control (FC) | — | |
| W35 | OEM-E3-6 | G5VOODOOPROV-E-E4 | 0.5 | no route | Check-engine lamp (W) | — | |
| W36 | OEM-E5-12 | G5VOODOOPROV-E-E3 | 0.5 | no route | Canister close valve (CCV) | — | |
| W37 | OEM-E6-7 | G5VOODOOPROV-E-E2 | 0.5 | no route | EVAP purge VSV (PRG) | — | |
| W38 | OEM-E7-5 | G5VOODOOPROV-E-E1 | 0.5 | no route | ACIS intake VSV | — | |
| W39 | OEM-E6-10 | G5VOODOOPROV-B-B33 | 0.5 | no route | Mass air flow (VG) | — | |
| W40 | OEM-E2-24 | G5VOODOOPROV-B-B15 | 0.5 | no route | O2 right rear (OXR2) | — | |
| W41 | OEM-E4-8 | G5VOODOOPROV-B-B16 | 0.5 | no route | O2 left rear (OXL2) | — | |
| W42 | OEM-E6-11 | G5VOODOOPROV-B-B23 | 0.5 | no route | O2 right front (OXR1) | — | |
| W43 | OEM-E6-12 | G5VOODOOPROV-B-B24 | 0.5 | no route | O2 left front (OXL1) | — | |
| W44 | OEM-E6-22 | G5VOODOOPROV-A-A16 | 0.5 | no route | Intake air temperature (THA) | — | |
| W45 | OEM-E4-18 | G5VOODOOPROV-B-B31 | 0.5 | no route | EVAP vapor pressure (PTNK) | — | |
| W46 | OEM-E5-11 | G5VOODOOPROV-A-A30 | 0.5 | no route | Vehicle speed sensor (SP2-) | — | |
| W47 | OEM-E5-5 | G5VOODOOPROV-A-A31 | 0.5 | no route | Vehicle speed sensor (SP2+) | — | |
| W48 | OEM-E7-25 | G5VOODOOPROV-A-A23 | 0.5 | no route | Igniter feedback (IGF) | — | |
| W49 | OEM-E4-2 | G5VOODOOPROV-B-B21 | 0.5 | no route | Starter signal (STA) | — | |
| W50 | OEM-E4-5 | G5VOODOOPROV-B-B20 | 0.5 | no route | Diagnostic/timing check (TC) | — | |
| W51 | OEM-E4-6 | G5VOODOOPROV-B-B19 | 0.5 | no route | Stop light switch (STP) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (22)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | REQUIRED_UNMAPPED | OEM-E3-16 | Required OEM function "EFI main relay (+B)" (power_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-E3-7 | Required OEM function "ETCS main relay (+BM)" (power_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-E3-8 | Required OEM function "EFI main relay (+B2)" (power_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-E6-17 | Required OEM function "Power ground (E1)" (ground) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-E6-18 | Required OEM function "Sensor ground (E2)" (sensor_ground) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-E7-21 | Required OEM function "Power ground (E01)" (ground) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-E7-7 | Required OEM function "ETCS throttle motor - (M-)" (hbridge_out) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-E7-8 | Required OEM function "ETCS throttle motor + (M+)" (hbridge_out) is not connected to the new ECU. |
| warn | LOAD_UNKNOWN | G5VOODOOPROV-A-A29 | G5VOODOOPROV-A-A29 "Aux 5" drives OEM-E4-13 A/C clutch relay (ACMG) (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | G5VOODOOPROV-E-E15 | G5VOODOOPROV-E-E15 "Aux 13 / WB Heater 1" drives OEM-E3-10 EFI main relay control (MREL) (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| warn | LOAD_UNKNOWN | G5VOODOOPROV-E-E22 | G5VOODOOPROV-E-E22 "Aux 14 / WB Heater 2" drives OEM-E3-4 Fuel pump relay (FPR) (load 0.2 A) but its current rating is unknown. Check the ECU manual. |
| info | NET_FAMILY | OEM-E2-25 ↔ G5VOODOOPROV-A-A28 | OEM-E2-25 "O2 heater right rear (HTR2)" [low_side_out] is wired to G5VOODOOPROV-A-A28 "Aux 6" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-E2-26 ↔ G5VOODOOPROV-A-A27 | OEM-E2-26 "O2 heater left rear (HTL2)" [low_side_out] is wired to G5VOODOOPROV-A-A27 "Aux 7" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-E3-5 ↔ G5VOODOOPROV-B-B1 | OEM-E3-5 "Fuel pump control (FC)" [low_side_out] is wired to G5VOODOOPROV-B-B1 "Injection 8" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-E3-6 ↔ G5VOODOOPROV-E-E4 | OEM-E3-6 "Check-engine lamp (W)" [low_side_out] is wired to G5VOODOOPROV-E-E4 "Injection 9" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-E4-13 ↔ G5VOODOOPROV-A-A29 | OEM-E4-13 "A/C clutch relay (ACMG)" [low_side_out] is wired to G5VOODOOPROV-A-A29 "Aux 5" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-E5-12 ↔ G5VOODOOPROV-E-E3 | OEM-E5-12 "Canister close valve (CCV)" [low_side_out] is wired to G5VOODOOPROV-E-E3 "Injection 10" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-E6-3 ↔ G5VOODOOPROV-A-A26 | OEM-E6-3 "O2 heater right front (HTR)" [low_side_out] is wired to G5VOODOOPROV-A-A26 "Aux 8" [switch_out]. Configure this output as low side. |
| info | NET_FAMILY | OEM-E6-4 ↔ G5VOODOOPROV-B-B2 | OEM-E6-4 "O2 heater left front (HTL)" [low_side_out] is wired to G5VOODOOPROV-B-B2 "Injection 7" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-E6-7 ↔ G5VOODOOPROV-E-E2 | OEM-E6-7 "EVAP purge VSV (PRG)" [low_side_out] is wired to G5VOODOOPROV-E-E2 "Injection 11" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | NET_FAMILY | OEM-E7-5 ↔ G5VOODOOPROV-E-E1 | OEM-E7-5 "ACIS intake VSV" [low_side_out] is wired to G5VOODOOPROV-E-E1 "Injection 12" [injector_out]. Injector drivers can usually run general low-side loads; check current and PWM frequency. |
| info | UNMAPPED | OEM | 4 optional OEM pins are not mapped: OEM-E2-13 ETCS power (TBP, throttle bypass); OEM-E3-11 Serial diagnostic (SIL); OEM-E6-19 MAF ground (EVG); OEM-E7-22 Crank position return (NE-) |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-E3-1 | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-11. Review every wire against both manuals before building. Open items: - Main-relay feed: no ecu_main_power pin on the stock or the new ECU - Link G5 Voodoo Pro V1: no power-ground pins in the library - Link G5 Voodoo Pro V1: no sensor-ground pin in the library - OEM-E3 16: EFI main relay (+B): no rule for class ecu_main_power; wire by hand - OEM-E3 7: ETCS main relay (+BM): no rule for class ecu_main_power; wire by hand - OEM-E3 8: EFI main relay (+B2): no rule for class ecu_main_power; wire by hand - OEM-E6 18: Sensor ground (E2): no rule for class ground_sensor; wire by hand - OEM-E7 7: ETCS throttle motor - (M-): no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand - OEM-E7 8: ETCS throttle motor + (M+): no +/− pair in the pinout (multi-phase or half-documented motor); wire by hand Not wired: - OEM-E3 1: Battery constant (BATT): Link G5 Voodoo Pro V1 has no battery-constant input; not needed - OEM-E3 11: Serial diagnostic (SIL): no free k_line on Link G5 Voodoo Pro V1 - OEM-E2 13: ETCS power (TBP, throttle bypass): no rule for class ecu_main_power; wire by hand - OEM-E6 19: MAF ground (EVG): no rule for class ground_sensor; wire by hand - OEM-E7 22: Crank position return (NE-): no rule for class ground_sensor; wire by hand
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | Link G5 Voodoo Pro V1 Installer I/O Table | https://kb.linkecu.com/__attachments/a_5cf0fc044bcfb915ac75562b29399beb93e47860e38990b3c01614530f927686/G5%20Voodoo%20Pro%20V1%20Installer%20IO%20Table.pdf | — | — | — |
| 4 | service_manual | Toyota FSM RM779U (2001 Lexus IS300) — DIAGNOSTICS 'TERMINALS OF ECM' (DI-20/21) | http://www.2jzgarage.com/wp-content/uploads/2013/04/2001_IS300_ECU_Pinouts.pdf | — | — | — |