Lexus LS400 1989-97 (1UZ-FE non-VVTi) → ECUMASTER EMU PRO 16 (auto)
Lexus LS400 1989-97 (1UZ-FE non-VVTi) — ECUMASTER — EMU PRO 16
⚠ NOT CHECKED. Don't build from this.
Drawn by Michael Gnankou · Rev 0 · draft · 2026-10-12
Before you start
Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
| Status | draft · not yet verified: nobody has reported building and running this harness |
|---|---|
| Open errors | 2: read the Findings page before cutting any wire |
| Size of the job | 65 wires · 11 connectors · 5 part lines |
| Tools | Crimp and extraction tools for each terminal family (see Connectors) · wire strippers · multimeter · heat gun + heat-shrink |
| Terminals | 3-1447221-4 |
| Order of work | 1. Check every part against the parts list. 2. Cut and label every wire (labels: Export → Wire labels). 3. Crimp and pin connector by connector, ticking the build checklist. 4. Run the bench test with nothing plugged in and the battery disconnected. 5. Only then connect the ECU and power up. |
Build checklist
Tick each box as you go. Continuity: meter from end to end, expect under 1 Ω.
| Wire | From | To | Gauge | Colour | Cut | Label | Crimp A | Crimp B | Pin A | Pin B | Continuity |
|---|---|---|---|---|---|---|---|---|---|---|---|
| W1 | OEM-A-12 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W2 | OEM-A-13 | SP-14V-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W3 | SP-14V-1 | EMUPRO16-B-14 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W4 | SP-14V-1 | EMUPRO16-B-8 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W5 | OEM-A-22 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W6 | OEM-D-13 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W7 | OEM-D-26 | SP-GND-1 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W8 | SP-GND-1 | EMUPRO16-A-11 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W9 | SP-GND-1 | EMUPRO16-A-17 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W10 | SP-GND-1 | EMUPRO16-A-19 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W11 | SP-GND-1 | EMUPRO16-B-19 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W12 | SP-GND-1 | EMUPRO16-C-30 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W13 | SP-GND-1 | EMUPRO16-D-18 | 0.85 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W14 | OEM-A-18 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W15 | OEM-C-15 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W16 | OEM-C-16 | SP-0V-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W17 | SP-0V-1 | EMUPRO16-A-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W18 | SP-0V-1 | EMUPRO16-B-9 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W19 | SP-0V-1 | EMUPRO16-C-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W20 | SP-0V-1 | EMUPRO16-D-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W21 | OEM-A-11 | EMUPRO16-A-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W22 | OEM-C-8 | EMUPRO16-A-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W23 | OEM-C-3 | EMUPRO16-B-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W24 | OEM-C-11 | EMUPRO16-B-17 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W25 | OEM-C-5 | EMUPRO16-A-30 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W26 | OEM-C-13 | EMUPRO16-A-29 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W27 | OEM-D-12 | EMUPRO16-A-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W28 | OEM-D-11 | EMUPRO16-A-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W29 | OEM-D-24 | EMUPRO16-A-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W30 | OEM-D-25 | EMUPRO16-A-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W31 | OEM-A-1 | EMUPRO16-B-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W32 | OEM-A-4 | EMUPRO16-C-31 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W33 | OEM-A-5 | EMUPRO16-C-18 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W34 | OEM-B-4 | EMUPRO16-B-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W35 | OEM-B-6 | EMUPRO16-B-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W36 | OEM-B-7 | EMUPRO16-B-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W37 | OEM-D-19 | EMUPRO16-B-4 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W38 | OEM-D-20 | EMUPRO16-B-5 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W39 | OEM-D-17 | EMUPRO16-B-6 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W40 | OEM-D-8 | EMUPRO16-B-7 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W41 | OEM-D-7 | EMUPRO16-B-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W42 | OEM-D-6 | EMUPRO16-A-25 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W43 | OEM-D-5 | EMUPRO16-C-1 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W44 | OEM-B-5 | EMUPRO16-C-2 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W45 | OEM-B-8 | EMUPRO16-C-3 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W46 | OEM-D-21 | EMUPRO16-D-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W47 | OEM-D-22 | EMUPRO16-D-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W48 | OEM-D-4 | EMUPRO16-D-26 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W49 | OEM-A-17 | EMUPRO16-C-32 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W50 | OEM-A-6 | EMUPRO16-C-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W51 | OEM-B-11 | EMUPRO16-C-33 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W52 | OEM-B-24 | EMUPRO16-C-19 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W53 | OEM-A-16 | EMUPRO16-C-34 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W54 | OEM-A-7 | EMUPRO16-C-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W55 | OEM-C-2 | EMUPRO16-A-13 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W56 | OEM-C-10 | EMUPRO16-A-22 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W57 | OEM-A-19 | EMUPRO16-A-14 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W58 | OEM-A-9 | EMUPRO16-A-24 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W59 | OEM-A-20 | EMUPRO16-A-16 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W60 | OEM-A-14 | EMUPRO16-A-23 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W61 | OEM-A-2 | EMUPRO16-A-15 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W62 | OEM-B-19 | EMUPRO16-D-11 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W63 | OEM-B-20 | EMUPRO16-D-12 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W64 | OEM-B-23 | EMUPRO16-D-21 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | |
| W65 | OEM-C-1 | EMUPRO16-C-20 | 0.5 | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ | ☐ |
Bench test (before first power-up)
Battery disconnected, ECU and every sensor unplugged. Meter on resistance. Each pair below must read open (OL): a reading means a pinched wire, a stray strand or a mis-pinned cavity. Then check continuity of every wire (last column of the build checklist).
| # | Probe A | Probe B | Expect | Why | Reading |
|---|---|---|---|---|---|
| 1 | EMUPRO16-A-12 | EMUPRO16-A-11 | open (OL) | 5 V sensor reference must not touch power ground | |
| 2 | EMUPRO16-A-12 | EMUPRO16-A-20 | open (OL) | 5 V sensor reference must not touch sensor ground | |
| 3 | EMUPRO16-B-14 | EMUPRO16-A-11 | open (OL) | +12 V supply must not touch power ground | |
| 4 | EMUPRO16-B-14 | EMUPRO16-A-20 | open (OL) | +12 V supply must not touch sensor ground | |
| 5 | EMUPRO16-A-12 | EMUPRO16-B-14 | open (OL) | 5 V sensor reference must not touch +12 V supply |
If any reading doesn't match, stop and get help before powering up.
Revisions
| Rev | Label | By | Date |
|---|---|---|---|
| No revisions yet. | |||
Schematic
Connectors
EMUPRO16-A
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Ignition 8 | — | — | — | — | — | — | — | — |
| 2 | Injector 1 | — | W27 | — | 0.5 | OEM-D-12 | — | — | — |
| 3 | Injector 2 | — | W28 | — | 0.5 | OEM-D-11 | — | — | — |
| 4 | Injector 3 | — | W29 | — | 0.5 | OEM-D-24 | — | — | — |
| 5 | Injector 4 | — | W30 | — | 0.5 | OEM-D-25 | — | — | — |
| 6 | Injector 5 | — | — | — | — | — | — | — | — |
| 7 | Injector 6 | — | — | — | — | — | — | — | — |
| 8 | Injector 7 | — | — | — | — | — | — | — | — |
| 9 | Injector 8 | — | — | — | — | — | — | — | — |
| 10 | Ignition 7 | — | — | — | — | — | — | — | — |
| 11 | Power GND | — | W8 | — | 0.85 | SP-GND-1 | — | — | — |
| 12 | +5V source A | — | W21 | — | 0.5 | OEM-A-11 | — | — | — |
| 13 | Digital 2 | — | W55 | — | 0.5 | OEM-C-2 | — | — | — |
| 14 | Digital 4 | — | W57 | — | 0.5 | OEM-A-19 | — | — | — |
| 15 | Digital 8 | — | W61 | — | 0.5 | OEM-A-2 | — | — | — |
| 16 | Digital 6 (turbo) | — | W59 | — | 0.5 | OEM-A-20 | — | — | — |
| 17 | Power GND | — | W9 | — | 0.85 | SP-GND-1 | — | — | — |
| 18 | Ignition 6 | — | — | — | — | — | — | — | — |
| 19 | Power GND | — | W10 | — | 0.85 | SP-GND-1 | — | — | — |
| 20 | Digital GND | — | W17 | — | 0.5 | SP-0V-1 | — | — | — |
| 21 | Digital 1 (crank) | — | W22 | — | 0.5 | OEM-C-8 | — | — | — |
| 22 | Digital 3 | — | W56 | — | 0.5 | OEM-C-10 | — | — | — |
| 23 | Digital 7 | — | W60 | — | 0.5 | OEM-A-14 | — | — | — |
| 24 | Digital 5 (turbo) | — | W58 | — | 0.5 | OEM-A-9 | — | — | — |
| 25 | Auxiliary 9 | — | W42 | — | 0.5 | OEM-D-6 | — | — | — |
| 26 | Ignition 5 | — | — | — | — | — | — | — | — |
| 27 | Ignition 4 | — | — | — | — | — | — | — | — |
| 28 | Ignition 3 | — | — | — | — | — | — | — | — |
| 29 | Ignition 2 | — | W26 | — | 0.5 | OEM-C-13 | — | — | — |
| 30 | Ignition 1 | — | W25 | — | 0.5 | OEM-C-5 | — | — | — |
| 31 | CAN 1 high (PC comm) | — | — | — | — | — | — | — | — |
| 32 | CAN 1 low (PC comm) | — | — | — | — | — | — | — | — |
| 33 | CAN 2 high | — | — | — | — | — | — | — | — |
| 34 | CAN 2 low | — | — | — | — | — | — | — | — |
EMUPRO16-B
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Auxiliary 1 (WBO heater) | — | W34 | — | 0.5 | OEM-B-4 | — | — | — |
| 2 | Auxiliary 2 (WBO heater) | — | W35 | — | 0.5 | OEM-B-6 | — | — | — |
| 3 | Auxiliary 3 (WBO heater) | — | W36 | — | 0.5 | OEM-B-7 | — | — | — |
| 4 | Auxiliary 4 (WBO heater) | — | W37 | — | 0.5 | OEM-D-19 | — | — | — |
| 5 | Auxiliary 5 | — | W38 | — | 0.5 | OEM-D-20 | — | — | — |
| 6 | Auxiliary 6 | — | W39 | — | 0.5 | OEM-D-17 | — | — | — |
| 7 | Auxiliary 7 | — | W40 | — | 0.5 | OEM-D-8 | — | — | — |
| 8 | +12V supply | — | W4 | — | 0.85 | SP-14V-1 | — | — | — |
| 9 | Digital GND (flash drive) | — | W18 | — | 0.5 | SP-0V-1 | — | — | — |
| 10 | USB D- (flash drive) | — | — | — | — | — | — | — | — |
| 11 | USB D+ (flash drive) | — | — | — | — | — | — | — | — |
| 12 | +5V source A (flash drive) | — | — | — | — | — | — | — | — |
| 13 | Auxiliary 8 | — | W41 | — | 0.5 | OEM-D-7 | — | — | — |
| 14 | +12V supply | — | W3 | — | 0.85 | SP-14V-1 | — | — | — |
| 15 | +12V switched | — | W31 | — | 0.5 | OEM-A-1 | — | — | — |
| 16 | Knock sensor 1 | — | W23 | — | 0.5 | OEM-C-3 | — | — | — |
| 17 | Knock sensor 2 | — | W24 | — | 0.5 | OEM-C-11 | — | — | — |
| 18 | WBO 2 VGND (LSU 4.9) | — | — | — | — | — | — | — | — |
| 19 | Power GND | — | W11 | — | 0.85 | SP-GND-1 | — | — | — |
| 20 | WBO 1 IP (LSU 4.9) | — | — | — | — | — | — | — | — |
| 21 | WBO 1 VS (LSU 4.9) | — | — | — | — | — | — | — | — |
| 22 | WBO 1 RCAL (LSU 4.9) | — | — | — | — | — | — | — | — |
| 23 | WBO 1 VGND (LSU 4.9) | — | — | — | — | — | — | — | — |
| 24 | WBO 2 IP (LSU 4.9) | — | — | — | — | — | — | — | — |
| 25 | WBO 2 VS (LSU 4.9) | — | — | — | — | — | — | — | — |
| 26 | WBO 2 RCAL (LSU 4.9) | — | — | — | — | — | — | — | — |
EMUPRO16-C
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Auxiliary 10 | — | W43 | — | 0.5 | OEM-D-5 | — | — | — |
| 2 | Auxiliary 11 | — | W44 | — | 0.5 | OEM-B-5 | — | — | — |
| 3 | Auxiliary 12 | — | W45 | — | 0.5 | OEM-B-8 | — | — | — |
| 4 | Analog 7 | — | — | — | — | — | — | — | — |
| 5 | Analog 10 (2k2 pull) | — | — | — | — | — | — | — | — |
| 6 | H-bridge 1A | — | — | — | — | — | — | — | — |
| 7 | H-bridge 2B | — | — | — | — | — | — | — | — |
| 8 | H-bridge 3A | — | — | — | — | — | — | — | — |
| 9 | H-bridge 2A | — | — | — | — | — | — | — | — |
| 10 | Analog 1 (MAP) | — | — | — | — | — | — | — | — |
| 11 | Analog 3 | — | W50 | — | 0.5 | OEM-A-6 | — | — | — |
| 12 | Analog 5 | — | W54 | — | 0.5 | OEM-A-7 | — | — | — |
| 13 | Analog 8 | — | — | — | — | — | — | — | — |
| 14 | Analog 11 (2k2 pull) | — | — | — | — | — | — | — | — |
| 15 | Analog 13 (1k pull) | — | — | — | — | — | — | — | — |
| 16 | Analog 15 (330R pull) | — | — | — | — | — | — | — | — |
| 17 | H-bridge 3B | — | — | — | — | — | — | — | — |
| 18 | Analog 2 | — | W33 | — | 0.5 | OEM-A-5 | — | — | — |
| 19 | Analog 4 | — | W52 | — | 0.5 | OEM-B-24 | — | — | — |
| 20 | Analog 6 | — | W65 | — | 0.5 | OEM-C-1 | — | — | — |
| 21 | Analog 9 (2k2 pull) | — | — | — | — | — | — | — | — |
| 22 | Analog 12 (2k2 pull) | — | — | — | — | — | — | — | — |
| 23 | Analog 14 (1k pull) | — | — | — | — | — | — | — | — |
| 24 | Analog 16 (100R pull) | — | — | — | — | — | — | — | — |
| 25 | H-bridge 1B | — | — | — | — | — | — | — | — |
| 26 | LIN | — | — | — | — | — | — | — | — |
| 27 | +5V source B | — | — | — | — | — | — | — | — |
| 28 | +5V source B | — | — | — | — | — | — | — | — |
| 29 | Analog GND | — | W19 | — | 0.5 | SP-0V-1 | — | — | — |
| 30 | Power GND | — | W12 | — | 0.85 | SP-GND-1 | — | — | — |
| 31 | Precision analog 1 | — | W32 | — | 0.5 | OEM-A-4 | — | — | — |
| 32 | Precision analog 2 | — | W49 | — | 0.5 | OEM-A-17 | — | — | — |
| 33 | Precision analog 3 | — | W51 | — | 0.5 | OEM-B-11 | — | — | — |
| 34 | Precision analog 4 | — | W53 | — | 0.5 | OEM-A-16 | — | — | — |
EMUPRO16-D
Mating face
Wire side
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Injector 10 | — | — | — | — | — | — | — | — |
| 2 | Injector 11 | — | — | — | — | — | — | — | — |
| 3 | Injector 12 | — | — | — | — | — | — | — | — |
| 4 | Injector 13 | — | — | — | — | — | — | — | — |
| 5 | Injector 14 | — | — | — | — | — | — | — | — |
| 6 | Injector 15 | — | — | — | — | — | — | — | — |
| 7 | Injector 16 | — | — | — | — | — | — | — | — |
| 8 | Injector 9 | — | — | — | — | — | — | — | — |
| 9 | Analog 17 | — | — | — | — | — | — | — | — |
| 10 | Analog 18 | — | — | — | — | — | — | — | — |
| 11 | Digital 9 / Analog 19 | — | W62 | — | 0.5 | OEM-B-19 | — | — | — |
| 12 | Digital 10 / Analog 20 | — | W63 | — | 0.5 | OEM-B-20 | — | — | — |
| 13 | Auxiliary 13 | — | W46 | — | 0.5 | OEM-D-21 | — | — | — |
| 14 | H-bridge 4A | — | — | — | — | — | — | — | — |
| 15 | Precision analog 6 | — | — | — | — | — | — | — | — |
| 16 | Precision analog 8 | — | — | — | — | — | — | — | — |
| 17 | Analog GND | — | W20 | — | 0.5 | SP-0V-1 | — | — | — |
| 18 | Power GND | — | W13 | — | 0.85 | SP-GND-1 | — | — | — |
| 19 | Auxiliary 14 | — | W47 | — | 0.5 | OEM-D-22 | — | — | — |
| 20 | H-bridge 4B | — | — | — | — | — | — | — | — |
| 21 | Precision analog 5 | — | W64 | — | 0.5 | OEM-B-23 | — | — | — |
| 22 | Precision analog 7 | — | — | — | — | — | — | — | — |
| 23 | Ignition 9 | — | — | — | — | — | — | — | — |
| 24 | Ignition 10 | — | — | — | — | — | — | — | — |
| 25 | Auxiliary 16 | — | — | — | — | — | — | — | — |
| 26 | Auxiliary 15 | — | W48 | — | 0.5 | OEM-D-4 | — | — | — |
OEM-A
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | Ignition switch (IGSW) | — | W31 | — | 0.5 | EMUPRO16-B-15 | — | — | — |
| 11 | Sensor supply +5V (VC) | — | W21 | — | 0.5 | EMUPRO16-A-12 | — | — | — |
| 12 | EFI main relay (B+) | — | W1 | — | 0.85 | SP-14V-1 | — | — | — |
| 13 | EFI main relay (B1+) | — | W2 | — | 0.85 | SP-14V-1 | — | — | — |
| 14 | Neutral start switch (NSW) | — | W60 | — | 0.5 | EMUPRO16-A-23 | — | — | — |
| 16 | Intake air temperature (THA) | — | W53 | — | 0.5 | EMUPRO16-C-34 | — | — | — |
| 17 | O2 right front (OXR1) | — | W49 | — | 0.5 | EMUPRO16-C-32 | — | — | — |
| 18 | Sensor ground (E2) | — | W14 | — | 0.5 | SP-0V-1 | — | — | — |
| 19 | Vehicle speed (SPD) | — | W57 | — | 0.5 | EMUPRO16-A-14 | — | — | — |
| 2 | Starter signal (STA) | — | W61 | — | 0.5 | EMUPRO16-A-15 | — | — | — |
| 20 | Diagnostic test 2 (TE2) | — | W59 | — | 0.5 | EMUPRO16-A-16 | — | — | — |
| 22 | Power ground (E1) | — | W5 | — | 0.85 | SP-GND-1 | — | — | — |
| 4 | Throttle position (VTA1) | — | W32 | — | 0.5 | EMUPRO16-C-31 | — | — | — |
| 5 | Coolant temperature (THW) | — | W33 | — | 0.5 | EMUPRO16-C-18 | — | — | — |
| 6 | O2 left front (OXL1) | — | W50 | — | 0.5 | EMUPRO16-C-11 | — | — | — |
| 7 | EGR temperature sensor | — | W54 | — | 0.5 | EMUPRO16-C-12 | — | — | — |
| 8 | Knock/shield (KS) | — | — | — | — | — | — | — | — |
| 9 | Diagnostic test 1 (TE1) | — | W58 | — | 0.5 | EMUPRO16-A-24 | — | — | — |
OEM-B
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 11 | O2 right rear (OXR2) | — | W51 | — | 0.5 | EMUPRO16-C-33 | — | — | — |
| 19 | Stop light switch (BK) | — | W62 | — | 0.5 | EMUPRO16-D-11 | — | — | — |
| 20 | A/T kickdown switch (KD) | — | W63 | — | 0.5 | EMUPRO16-D-12 | — | — | — |
| 23 | A/C request (AC) | — | W64 | — | 0.5 | EMUPRO16-D-21 | — | — | — |
| 24 | O2 left rear (OXL2) | — | W52 | — | 0.5 | EMUPRO16-C-19 | — | — | — |
| 26 | Battery constant (BATT) | — | — | — | — | — | — | — | — |
| 4 | EFI main relay control (MREL) | — | W34 | — | 0.5 | EMUPRO16-B-1 | — | — | — |
| 5 | Check-engine lamp (W) | — | W44 | — | 0.5 | EMUPRO16-C-2 | — | — | — |
| 6 | Fuel pump relay (FPR) | — | W35 | — | 0.5 | EMUPRO16-B-2 | — | — | — |
| 7 | A/C clutch relay (ACMG) | — | W36 | — | 0.5 | EMUPRO16-B-3 | — | — | — |
| 8 | Fuel pump control (FC) | — | W45 | — | 0.5 | EMUPRO16-C-3 | — | — | — |
OEM-C
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | TPS idle switch (IDL) | — | W65 | — | 0.5 | EMUPRO16-C-20 | — | — | — |
| 10 | Igniter 2 feedback (IGF2) | — | W56 | — | 0.5 | EMUPRO16-A-22 | — | — | — |
| 11 | Knock sensor 2 (KNK2) | — | W24 | — | 0.5 | EMUPRO16-B-17 | — | — | — |
| 12 | Check connector VF2 | — | — | — | — | — | — | — | — |
| 13 | Ignition 2 (IGT2) | — | W26 | — | 0.5 | EMUPRO16-A-29 | — | — | — |
| 15 | Cam sensor ground (G-) | — | W15 | — | 0.5 | SP-0V-1 | — | — | — |
| 16 | Crank sensor - (NE-) | — | W16 | — | 0.5 | SP-0V-1 | — | — | — |
| 2 | Igniter 1 feedback (IGF1) | — | W55 | — | 0.5 | EMUPRO16-A-13 | — | — | — |
| 3 | Knock sensor 1 (KNK1) | — | W23 | — | 0.5 | EMUPRO16-B-16 | — | — | — |
| 4 | Check connector VF1 | — | — | — | — | — | — | — | — |
| 5 | Ignition 1 (IGT1) | — | W25 | — | 0.5 | EMUPRO16-A-30 | — | — | — |
| 6 | Cam sensor 2 + (G2+) | — | — | — | — | — | — | — | — |
| 7 | Cam sensor 1 + (G1+) | — | — | — | — | — | — | — | — |
| 8 | Crank sensor + (NE+) | — | W22 | — | 0.5 | EMUPRO16-A-21 | — | — | — |
OEM-D
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 11 | Injector 2&8 (#20) | — | W28 | — | 0.5 | EMUPRO16-A-3 | — | — | — |
| 12 | Injector 1&7 (#10) | — | W27 | — | 0.5 | EMUPRO16-A-2 | — | — | — |
| 13 | Power ground (E01) | — | W6 | — | 0.85 | SP-GND-1 | — | — | — |
| 17 | Cold start injector 1 (STJ1) | — | W39 | — | 0.5 | EMUPRO16-B-6 | — | — | — |
| 19 | O2 heater 2 (HT2) | — | W37 | — | 0.5 | EMUPRO16-B-4 | — | — | — |
| 20 | O2 heater 1 (HT1) | — | W38 | — | 0.5 | EMUPRO16-B-5 | — | — | — |
| 21 | EGR solenoid | — | W46 | — | 0.5 | EMUPRO16-D-13 | — | — | — |
| 22 | Fuel pressure-up VSV (PR) | — | W47 | — | 0.5 | EMUPRO16-D-19 | — | — | — |
| 24 | Injector 3&5 (#40) | — | W29 | — | 0.5 | EMUPRO16-A-4 | — | — | — |
| 25 | Injector 4&6 (#30) | — | W30 | — | 0.5 | EMUPRO16-A-5 | — | — | — |
| 26 | Power ground (E02) | — | W7 | — | 0.85 | SP-GND-1 | — | — | — |
| 4 | Cold start injector (STJ) | — | W48 | — | 0.5 | EMUPRO16-D-26 | — | — | — |
| 5 | ISC stepper coil 4 (ISC4) | — | W43 | — | 0.5 | EMUPRO16-C-1 | — | — | — |
| 6 | ISC stepper coil 3 (ISC3) | — | W42 | — | 0.5 | EMUPRO16-A-25 | — | — | — |
| 7 | ISC stepper coil 2 (ISC2) | — | W41 | — | 0.5 | EMUPRO16-B-13 | — | — | — |
| 8 | ISC stepper coil 1 (ISC1) | — | W40 | — | 0.5 | EMUPRO16-B-7 | — | — | — |
SP-0V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W14 | — | 0.5 | OEM-A-18 | — | — | — |
| 1 | — | — | W15 | — | 0.5 | OEM-C-15 | — | — | — |
| 1 | — | — | W16 | — | 0.5 | OEM-C-16 | — | — | — |
| 1 | — | — | W17 | — | 0.5 | EMUPRO16-A-20 | — | — | — |
| 1 | — | — | W18 | — | 0.5 | EMUPRO16-B-9 | — | — | — |
| 1 | — | — | W19 | — | 0.5 | EMUPRO16-C-29 | — | — | — |
| 1 | — | — | W20 | — | 0.5 | EMUPRO16-D-17 | — | — | — |
SP-14V
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W1 | — | 0.85 | OEM-A-12 | — | — | — |
| 1 | — | — | W2 | — | 0.85 | OEM-A-13 | — | — | — |
| 1 | — | — | W3 | — | 0.85 | EMUPRO16-B-14 | — | — | — |
| 1 | — | — | W4 | — | 0.85 | EMUPRO16-B-8 | — | — | — |
SP-GND
| Cavity | Function | Signal | Wire | Colour | Gauge (mm²) | Destination | Terminal | Seal | Plug |
|---|---|---|---|---|---|---|---|---|---|
| 1 | — | — | W5 | — | 0.85 | OEM-A-22 | — | — | — |
| 1 | — | — | W6 | — | 0.85 | OEM-D-13 | — | — | — |
| 1 | — | — | W7 | — | 0.85 | OEM-D-26 | — | — | — |
| 1 | — | — | W8 | — | 0.85 | EMUPRO16-A-11 | — | — | — |
| 1 | — | — | W9 | — | 0.85 | EMUPRO16-A-17 | — | — | — |
| 1 | — | — | W10 | — | 0.85 | EMUPRO16-A-19 | — | — | — |
| 1 | — | — | W11 | — | 0.85 | EMUPRO16-B-19 | — | — | — |
| 1 | — | — | W12 | — | 0.85 | EMUPRO16-C-30 | — | — | — |
| 1 | — | — | W13 | — | 0.85 | EMUPRO16-D-18 | — | — | — |
Pin map
| OEM point | OEM function | OEM family | Target point | Target function | Target family | Wire colour | Evidence |
|---|---|---|---|---|---|---|---|
| OEM-A-1 | Ignition switch (IGSW) | digital_in | EMUPRO16-B-15 | +12V switched | digital_in | single_source | |
| OEM-A-11 | Sensor supply +5V (VC) | vref | EMUPRO16-A-12 | +5V source A | vref | single_source | |
| OEM-A-12 | EFI main relay (B+) | power_in | EMUPRO16-B-14 + EMUPRO16-B-8 | +12V supply + +12V supply | power_in | single_source | |
| OEM-A-13 | EFI main relay (B1+) | power_in | EMUPRO16-B-14 + EMUPRO16-B-8 | +12V supply + +12V supply | power_in | single_source | |
| OEM-A-14 | Neutral start switch (NSW) | digital_in | EMUPRO16-A-23 | Digital 7 | digital_in | single_source | |
| OEM-A-16 | Intake air temperature (THA) | temp_in | EMUPRO16-C-34 | Precision analog 4 | analog_in | single_source | |
| OEM-A-17 | O2 right front (OXR1) | lambda_nb_in | EMUPRO16-C-32 | Precision analog 2 | analog_in | single_source | |
| OEM-A-18 | Sensor ground (E2) | sensor_ground | EMUPRO16-A-20 + EMUPRO16-B-9 + EMUPRO16-C-29 + EMUPRO16-D-17 | Digital GND + Digital GND (flash drive) + Analog GND + Analog GND | sensor_ground | single_source | |
| OEM-A-19 | Vehicle speed (SPD) | digital_in | EMUPRO16-A-14 | Digital 4 | digital_in | single_source | |
| OEM-A-2 | Starter signal (STA) | digital_in | EMUPRO16-A-15 | Digital 8 | digital_in | single_source | |
| OEM-A-20 | Diagnostic test 2 (TE2) | digital_in | EMUPRO16-A-16 | Digital 6 (turbo) | digital_in | single_source | |
| OEM-A-22 | Power ground (E1) | ground | EMUPRO16-A-11 + EMUPRO16-A-17 + EMUPRO16-A-19 + EMUPRO16-B-19 + EMUPRO16-C-30 + EMUPRO16-D-18 | Power GND + Power GND + Power GND + Power GND + Power GND + Power GND | ground | single_source | |
| OEM-A-4 | Throttle position (VTA1) | analog_in | EMUPRO16-C-31 | Precision analog 1 | analog_in | single_source | |
| OEM-A-5 | Coolant temperature (THW) | temp_in | EMUPRO16-C-18 | Analog 2 | analog_in | single_source | |
| OEM-A-6 | O2 left front (OXL1) | lambda_nb_in | EMUPRO16-C-11 | Analog 3 | analog_in | single_source | |
| OEM-A-7 | EGR temperature sensor | temp_in | EMUPRO16-C-12 | Analog 5 | analog_in | single_source | |
| OEM-A-8 | Knock/shield (KS) | knock_in | — | — | — | single_source | |
| OEM-A-9 | Diagnostic test 1 (TE1) | digital_in | EMUPRO16-A-24 | Digital 5 (turbo) | digital_in | single_source | |
| OEM-B-11 | O2 right rear (OXR2) | lambda_nb_in | EMUPRO16-C-33 | Precision analog 3 | analog_in | single_source | |
| OEM-B-19 | Stop light switch (BK) | digital_in | EMUPRO16-D-11 | Digital 9 / Analog 19 | digital_in | single_source | |
| OEM-B-20 | A/T kickdown switch (KD) | digital_in | EMUPRO16-D-12 | Digital 10 / Analog 20 | digital_in | single_source | |
| OEM-B-23 | A/C request (AC) | digital_in | EMUPRO16-D-21 | Precision analog 5 | analog_in | single_source | |
| OEM-B-24 | O2 left rear (OXL2) | lambda_nb_in | EMUPRO16-C-19 | Analog 4 | analog_in | single_source | |
| OEM-B-26 | Battery constant (BATT) | power_in | — | — | — | single_source | |
| OEM-B-4 | EFI main relay control (MREL) | low_side_out | EMUPRO16-B-1 | Auxiliary 1 (WBO heater) | low_side_out | single_source | |
| OEM-B-5 | Check-engine lamp (W) | low_side_out | EMUPRO16-C-2 | Auxiliary 11 | low_side_out | single_source | |
| OEM-B-6 | Fuel pump relay (FPR) | low_side_out | EMUPRO16-B-2 | Auxiliary 2 (WBO heater) | low_side_out | single_source | |
| OEM-B-7 | A/C clutch relay (ACMG) | low_side_out | EMUPRO16-B-3 | Auxiliary 3 (WBO heater) | low_side_out | single_source | |
| OEM-B-8 | Fuel pump control (FC) | low_side_out | EMUPRO16-C-3 | Auxiliary 12 | low_side_out | single_source | |
| OEM-C-1 | TPS idle switch (IDL) | digital_in | EMUPRO16-C-20 | Analog 6 | analog_in | single_source | |
| OEM-C-10 | Igniter 2 feedback (IGF2) | digital_in | EMUPRO16-A-22 | Digital 3 | digital_in | single_source | |
| OEM-C-11 | Knock sensor 2 (KNK2) | knock_in | EMUPRO16-B-17 | Knock sensor 2 | knock_in | single_source | |
| OEM-C-12 | Check connector VF2 | analog_out | — | — | — | single_source | |
| OEM-C-13 | Ignition 2 (IGT2) | ignition_out | EMUPRO16-A-29 | Ignition 2 | ignition_out | single_source | |
| OEM-C-15 | Cam sensor ground (G-) | sensor_ground | EMUPRO16-A-20 + EMUPRO16-B-9 + EMUPRO16-C-29 + EMUPRO16-D-17 | Digital GND + Digital GND (flash drive) + Analog GND + Analog GND | sensor_ground | single_source | |
| OEM-C-16 | Crank sensor - (NE-) | sensor_ground | EMUPRO16-A-20 + EMUPRO16-B-9 + EMUPRO16-C-29 + EMUPRO16-D-17 | Digital GND + Digital GND (flash drive) + Analog GND + Analog GND | sensor_ground | single_source | |
| OEM-C-2 | Igniter 1 feedback (IGF1) | digital_in | EMUPRO16-A-13 | Digital 2 | digital_in | single_source | |
| OEM-C-3 | Knock sensor 1 (KNK1) | knock_in | EMUPRO16-B-16 | Knock sensor 1 | knock_in | single_source | |
| OEM-C-4 | Check connector VF1 | analog_out | — | — | — | single_source | |
| OEM-C-5 | Ignition 1 (IGT1) | ignition_out | EMUPRO16-A-30 | Ignition 1 | ignition_out | single_source | |
| OEM-C-6 | Cam sensor 2 + (G2+) | trigger_in | — | — | — | single_source | |
| OEM-C-7 | Cam sensor 1 + (G1+) | trigger_in | — | — | — | single_source | |
| OEM-C-8 | Crank sensor + (NE+) | trigger_in | EMUPRO16-A-21 | Digital 1 (crank) | trigger_in | single_source | |
| OEM-D-11 | Injector 2&8 (#20) | injector_out | EMUPRO16-A-3 | Injector 2 | injector_out | single_source | |
| OEM-D-12 | Injector 1&7 (#10) | injector_out | EMUPRO16-A-2 | Injector 1 | injector_out | single_source | |
| OEM-D-13 | Power ground (E01) | ground | EMUPRO16-A-11 + EMUPRO16-A-17 + EMUPRO16-A-19 + EMUPRO16-B-19 + EMUPRO16-C-30 + EMUPRO16-D-18 | Power GND + Power GND + Power GND + Power GND + Power GND + Power GND | ground | single_source | |
| OEM-D-17 | Cold start injector 1 (STJ1) | low_side_out | EMUPRO16-B-6 | Auxiliary 6 | low_side_out | single_source | |
| OEM-D-19 | O2 heater 2 (HT2) | low_side_out | EMUPRO16-B-4 | Auxiliary 4 (WBO heater) | low_side_out | single_source | |
| OEM-D-20 | O2 heater 1 (HT1) | low_side_out | EMUPRO16-B-5 | Auxiliary 5 | low_side_out | single_source | |
| OEM-D-21 | EGR solenoid | low_side_out | EMUPRO16-D-13 | Auxiliary 13 | low_side_out | single_source | |
| OEM-D-22 | Fuel pressure-up VSV (PR) | low_side_out | EMUPRO16-D-19 | Auxiliary 14 | low_side_out | single_source | |
| OEM-D-24 | Injector 3&5 (#40) | injector_out | EMUPRO16-A-4 | Injector 3 | injector_out | single_source | |
| OEM-D-25 | Injector 4&6 (#30) | injector_out | EMUPRO16-A-5 | Injector 4 | injector_out | single_source | |
| OEM-D-26 | Power ground (E02) | ground | EMUPRO16-A-11 + EMUPRO16-A-17 + EMUPRO16-A-19 + EMUPRO16-B-19 + EMUPRO16-C-30 + EMUPRO16-D-18 | Power GND + Power GND + Power GND + Power GND + Power GND + Power GND | ground | single_source | |
| OEM-D-4 | Cold start injector (STJ) | low_side_out | EMUPRO16-D-26 | Auxiliary 15 | low_side_out | single_source | |
| OEM-D-5 | ISC stepper coil 4 (ISC4) | low_side_out | EMUPRO16-C-1 | Auxiliary 10 | low_side_out | single_source | |
| OEM-D-6 | ISC stepper coil 3 (ISC3) | low_side_out | EMUPRO16-A-25 | Auxiliary 9 | low_side_out | single_source | |
| OEM-D-7 | ISC stepper coil 2 (ISC2) | low_side_out | EMUPRO16-B-13 | Auxiliary 8 | low_side_out | single_source | |
| OEM-D-8 | ISC stepper coil 1 (ISC1) | low_side_out | EMUPRO16-B-7 | Auxiliary 7 | low_side_out | single_source |
Cut list
| Wire | From | To | Gauge (mm²) | Colour | Length | Signal | Ident |
|---|---|---|---|---|---|---|---|
| W1 | OEM-A-12 | SP-14V-1 | 0.85 | no route | EFI main relay (B+) | — | |
| W2 | OEM-A-13 | SP-14V-1 | 0.85 | no route | EFI main relay (B1+) | — | |
| W3 | SP-14V-1 | EMUPRO16-B-14 | 0.85 | no route | +12V supply | — | |
| W4 | SP-14V-1 | EMUPRO16-B-8 | 0.85 | no route | +12V supply | — | |
| W5 | OEM-A-22 | SP-GND-1 | 0.85 | no route | Power ground (E1) | — | |
| W6 | OEM-D-13 | SP-GND-1 | 0.85 | no route | Power ground (E01) | — | |
| W7 | OEM-D-26 | SP-GND-1 | 0.85 | no route | Power ground (E02) | — | |
| W8 | SP-GND-1 | EMUPRO16-A-11 | 0.85 | no route | Power GND | — | |
| W9 | SP-GND-1 | EMUPRO16-A-17 | 0.85 | no route | Power GND | — | |
| W10 | SP-GND-1 | EMUPRO16-A-19 | 0.85 | no route | Power GND | — | |
| W11 | SP-GND-1 | EMUPRO16-B-19 | 0.85 | no route | Power GND | — | |
| W12 | SP-GND-1 | EMUPRO16-C-30 | 0.85 | no route | Power GND | — | |
| W13 | SP-GND-1 | EMUPRO16-D-18 | 0.85 | no route | Power GND | — | |
| W14 | OEM-A-18 | SP-0V-1 | 0.5 | no route | Sensor ground (E2) | — | |
| W15 | OEM-C-15 | SP-0V-1 | 0.5 | no route | Cam sensor ground (G-) | — | |
| W16 | OEM-C-16 | SP-0V-1 | 0.5 | no route | Crank sensor - (NE-) | — | |
| W17 | SP-0V-1 | EMUPRO16-A-20 | 0.5 | no route | Digital GND | — | |
| W18 | SP-0V-1 | EMUPRO16-B-9 | 0.5 | no route | Digital GND (flash drive) | — | |
| W19 | SP-0V-1 | EMUPRO16-C-29 | 0.5 | no route | Analog GND | — | |
| W20 | SP-0V-1 | EMUPRO16-D-17 | 0.5 | no route | Analog GND | — | |
| W21 | OEM-A-11 | EMUPRO16-A-12 | 0.5 | no route | Sensor supply +5V (VC) | — | |
| W22 | OEM-C-8 | EMUPRO16-A-21 | 0.5 | no route | Crank sensor + (NE+) | — | |
| W23 | OEM-C-3 | EMUPRO16-B-16 | 0.5 | no route | Knock sensor 1 (KNK1) | — | |
| W24 | OEM-C-11 | EMUPRO16-B-17 | 0.5 | no route | Knock sensor 2 (KNK2) | — | |
| W25 | OEM-C-5 | EMUPRO16-A-30 | 0.5 | no route | Ignition 1 (IGT1) | — | |
| W26 | OEM-C-13 | EMUPRO16-A-29 | 0.5 | no route | Ignition 2 (IGT2) | — | |
| W27 | OEM-D-12 | EMUPRO16-A-2 | 0.5 | no route | Injector 1&7 (#10) | — | |
| W28 | OEM-D-11 | EMUPRO16-A-3 | 0.5 | no route | Injector 2&8 (#20) | — | |
| W29 | OEM-D-24 | EMUPRO16-A-4 | 0.5 | no route | Injector 3&5 (#40) | — | |
| W30 | OEM-D-25 | EMUPRO16-A-5 | 0.5 | no route | Injector 4&6 (#30) | — | |
| W31 | OEM-A-1 | EMUPRO16-B-15 | 0.5 | no route | Ignition switch (IGSW) | — | |
| W32 | OEM-A-4 | EMUPRO16-C-31 | 0.5 | no route | Throttle position (VTA1) | — | |
| W33 | OEM-A-5 | EMUPRO16-C-18 | 0.5 | no route | Coolant temperature (THW) | — | |
| W34 | OEM-B-4 | EMUPRO16-B-1 | 0.5 | no route | EFI main relay control (MREL) | — | |
| W35 | OEM-B-6 | EMUPRO16-B-2 | 0.5 | no route | Fuel pump relay (FPR) | — | |
| W36 | OEM-B-7 | EMUPRO16-B-3 | 0.5 | no route | A/C clutch relay (ACMG) | — | |
| W37 | OEM-D-19 | EMUPRO16-B-4 | 0.5 | no route | O2 heater 2 (HT2) | — | |
| W38 | OEM-D-20 | EMUPRO16-B-5 | 0.5 | no route | O2 heater 1 (HT1) | — | |
| W39 | OEM-D-17 | EMUPRO16-B-6 | 0.5 | no route | Cold start injector 1 (STJ1) | — | |
| W40 | OEM-D-8 | EMUPRO16-B-7 | 0.5 | no route | ISC stepper coil 1 (ISC1) | — | |
| W41 | OEM-D-7 | EMUPRO16-B-13 | 0.5 | no route | ISC stepper coil 2 (ISC2) | — | |
| W42 | OEM-D-6 | EMUPRO16-A-25 | 0.5 | no route | ISC stepper coil 3 (ISC3) | — | |
| W43 | OEM-D-5 | EMUPRO16-C-1 | 0.5 | no route | ISC stepper coil 4 (ISC4) | — | |
| W44 | OEM-B-5 | EMUPRO16-C-2 | 0.5 | no route | Check-engine lamp (W) | — | |
| W45 | OEM-B-8 | EMUPRO16-C-3 | 0.5 | no route | Fuel pump control (FC) | — | |
| W46 | OEM-D-21 | EMUPRO16-D-13 | 0.5 | no route | EGR solenoid | — | |
| W47 | OEM-D-22 | EMUPRO16-D-19 | 0.5 | no route | Fuel pressure-up VSV (PR) | — | |
| W48 | OEM-D-4 | EMUPRO16-D-26 | 0.5 | no route | Cold start injector (STJ) | — | |
| W49 | OEM-A-17 | EMUPRO16-C-32 | 0.5 | no route | O2 right front (OXR1) | — | |
| W50 | OEM-A-6 | EMUPRO16-C-11 | 0.5 | no route | O2 left front (OXL1) | — | |
| W51 | OEM-B-11 | EMUPRO16-C-33 | 0.5 | no route | O2 right rear (OXR2) | — | |
| W52 | OEM-B-24 | EMUPRO16-C-19 | 0.5 | no route | O2 left rear (OXL2) | — | |
| W53 | OEM-A-16 | EMUPRO16-C-34 | 0.5 | no route | Intake air temperature (THA) | — | |
| W54 | OEM-A-7 | EMUPRO16-C-12 | 0.5 | no route | EGR temperature sensor | — | |
| W55 | OEM-C-2 | EMUPRO16-A-13 | 0.5 | no route | Igniter 1 feedback (IGF1) | — | |
| W56 | OEM-C-10 | EMUPRO16-A-22 | 0.5 | no route | Igniter 2 feedback (IGF2) | — | |
| W57 | OEM-A-19 | EMUPRO16-A-14 | 0.5 | no route | Vehicle speed (SPD) | — | |
| W58 | OEM-A-9 | EMUPRO16-A-24 | 0.5 | no route | Diagnostic test 1 (TE1) | — | |
| W59 | OEM-A-20 | EMUPRO16-A-16 | 0.5 | no route | Diagnostic test 2 (TE2) | — | |
| W60 | OEM-A-14 | EMUPRO16-A-23 | 0.5 | no route | Neutral start switch (NSW) | — | |
| W61 | OEM-A-2 | EMUPRO16-A-15 | 0.5 | no route | Starter signal (STA) | — | |
| W62 | OEM-B-19 | EMUPRO16-D-11 | 0.5 | no route | Stop light switch (BK) | — | |
| W63 | OEM-B-20 | EMUPRO16-D-12 | 0.5 | no route | A/T kickdown switch (KD) | — | |
| W64 | OEM-B-23 | EMUPRO16-D-21 | 0.5 | no route | A/C request (AC) | — | |
| W65 | OEM-C-1 | EMUPRO16-C-20 | 0.5 | no route | TPS idle switch (IDL) | — |
Bill of materials
| Category | Part number | Manufacturer | Description | Qty | Unit |
|---|---|---|---|---|---|
| connector | 1473416-1 | TE | Superseal 1.0 26-way plug, Key 3 | 1.000 | ea |
| connector | 3-1437290-7 | TE | Superseal 1.0 26-way plug | 1.000 | ea |
| connector | 4-1437290-0 | TE | Superseal 1.0 34-way plug, Key 1 | 1.000 | ea |
| connector | 4-1437290-1 | TE | Superseal 1.0 34-way plug, Key 2 | 1.000 | ea |
| terminal | 3-1447221-4 | TE | Superseal 1.0 socket terminal, 20 AWG (0.5 sq mm) | 57.000 | ea |
ECU setup sheet
| Role | Engine ref | Engine signal | Sensor | ECU point | ECU function | ECU class | Setup flag |
|---|---|---|---|---|---|---|---|
| No configured channels. | |||||||
Findings
Open (8)
| Severity | Code | Subject | Message |
|---|---|---|---|
| error | REQUIRED_UNMAPPED | OEM-C-6 | Required OEM function "Cam sensor 2 + (G2+)" (trigger_in) is not connected to the new ECU. |
| error | REQUIRED_UNMAPPED | OEM-C-7 | Required OEM function "Cam sensor 1 + (G1+)" (trigger_in) is not connected to the new ECU. |
| warn | NET_FAMILY | OEM-B-23 ↔ EMUPRO16-D-21 | OEM-B-23 "A/C request (AC)" [digital_in] is wired to EMUPRO16-D-21 "Precision analog 5" [analog_in]. Analog and digital on one net. A switch on an analog input works with a pull-up and a threshold; an analog sensor on a digital input loses its value. |
| warn | NET_FAMILY | OEM-C-1 ↔ EMUPRO16-C-20 | OEM-C-1 "TPS idle switch (IDL)" [digital_in] is wired to EMUPRO16-C-20 "Analog 6" [analog_in]. Analog and digital on one net. A switch on an analog input works with a pull-up and a threshold; an analog sensor on a digital input loses its value. |
| info | NET_FAMILY | OEM-A-16 ↔ EMUPRO16-C-34 | OEM-A-16 "Intake air temperature (THA)" [temp_in] is wired to EMUPRO16-C-34 "Precision analog 4" [analog_in]. Thermistor on a plain analog input needs a pull-up; check the channel can enable one. |
| info | NET_FAMILY | OEM-A-5 ↔ EMUPRO16-C-18 | OEM-A-5 "Coolant temperature (THW)" [temp_in] is wired to EMUPRO16-C-18 "Analog 2" [analog_in]. Thermistor on a plain analog input needs a pull-up; check the channel can enable one. |
| info | NET_FAMILY | OEM-A-7 ↔ EMUPRO16-C-12 | OEM-A-7 "EGR temperature sensor" [temp_in] is wired to EMUPRO16-C-12 "Analog 5" [analog_in]. Thermistor on a plain analog input needs a pull-up; check the channel can enable one. |
| info | UNMAPPED | OEM | 3 optional OEM pins are not mapped: OEM-A-8 Knock/shield (KS); OEM-C-12 Check connector VF2; OEM-C-4 Check connector VF1 |
Accepted (1)
| Code | Subject | Reason | By |
|---|---|---|---|
| REQUIRED_UNMAPPED | OEM-B-26 | Battery-constant (memory) feed of the stock ECU: the new ECU has no such input, so it is not needed. | mapping-proposal |
Notes
Auto-mapped by auto_map() from the library pin data on 2026-10-11. Review every wire against both manuals before building. Open items: - OEM-C 7: Cam sensor 1 + (G1+): no free cam_vr/cam_hall/frequency_in input on ECUMASTER EMU PRO 16 - OEM-C 6: Cam sensor 2 + (G2+): no free cam_vr/cam_hall/frequency_in input on ECUMASTER EMU PRO 16 Not wired: - OEM-B 26: Battery constant (BATT): ECUMASTER EMU PRO 16 has no battery-constant input; not needed - OEM-A 8: Knock/shield (KS): no free knock input on ECUMASTER EMU PRO 16 - OEM-C 4: Check connector VF1: no free analog_out on ECUMASTER EMU PRO 16 - OEM-C 12: Check connector VF2: no free analog_out on ECUMASTER EMU PRO 16
Sources
| Reliability | Kind | Title | URL | Archive | Captured | SHA-256 |
|---|---|---|---|---|---|---|
| 4 | vendor_doc | ECUMASTER EMU PRO 16 — pinout (Connectors A/B/C/D) | https://www.ecumaster.com/files/EMU_PRO/EMU_PRO_16_Pinout_v1.0.pdf | archive | 2026-10-05 | 72799bed63fb |
| 2 | community_copy | Lextreme: Adaptronic install for 1UZ-FE (Lexus LS400/SC400) — 4-plug A/B/C/D ECU pin table (1992 LS400) | https://www.lextreme.com/installation-of-an-adaptronic-ecu-for-a-lexus-ls400-sc400-1uzfe-engine/ | — | — | — |