Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
100%
Stock ECU being replaced
SPEEDUINO-A-16 Proto area 3 (fuel pump)
SPEEDUINO-A-15 Proto area 2 (fan)
SPEEDUINO-A-18 Proto area 5 (clutch)
SPEEDUINO-A-38 VVT
SPEEDUINO-A-36 Idle 2 (3-wire idle)
SPEEDUINO-A-14 Proto area 1 (flex fuel)
SPEEDUINO-A-35 Boost
OEM-1
Stock ECU being replaced
ACooling fan relay (low-side)
BA/C condenser fan relay
CStarter input (12V while cranking)
ECheck engine light (MIL)
GA/C clutch relay
MVehicle speed sensor (VSS)
UFuel pump relay (low-side)
SPEEDUINO-A-21 O2 sensor
SPEEDUINO-A-22 TPS input
SPEEDUINO-A-19 Coolant temp (CLT)
SPEEDUINO-A-11 MAP sensor (0-5V)
5V ref
SPEEDUINO-A-20 Inlet air temp (IAT)
SPEEDUINO-A-37 PWM idle
0V sensor
OEM-3
Stock ECU being replaced
CFront O2 sensor input
FThrottle position (TPS)
GEngine coolant temp (CLT)
HEGR boost sensor
I+5V sensor reference
KIntake air temp (IAT)
MFront O2 heater control
OSensor ground
GND
GND
GND
SPEEDUINO-A-25 Crank input / VR1+
SPEEDUINO-A-26 VR2-
SPEEDUINO-A-24 Cam input / VR2+
0V sensor
GND
SPEEDUINO-A-17 Proto area 4 (tachometer)
SPEEDUINO-A-7 Ignition 1
SPEEDUINO-A-34 Ignition 2
SPEEDUINO-A-1 Injector 1
SPEEDUINO-A-2 Injector 2
SPEEDUINO-A-3 Injector 3
SPEEDUINO-A-5 Injector 4
OEM-4
Stock ECU being replaced
AChassis ground
CChassis ground
DChassis ground
ECrank position (CKP) sensor
FCAS SGT (cam trigger)
GCAS SGC (cam sync)
HCrank pickup timing ground (CKP gnd)
KChassis ground
LTachometer output
NIgnition coil trigger (cyl 1&4)
RIgnition coil trigger (cyl 2&3)
UInjector 1 (cyl 1)
VInjector 2 (cyl 2)
WInjector 3 (cyl 3)
XInjector 4 (cyl 4)
SPEEDUINO
SPEEDUINO-A
SPEEDUINO
1Injector 1
2Injector 2
3Injector 3
5Injector 4
7Ignition 1
9Ground
10Ground
11MAP sensor (0-5V)
12Ground
135V
14Proto area 1 (flex fuel)
15Proto area 2 (fan)
16Proto area 3 (fuel pump)
17Proto area 4 (tachometer)
18Proto area 5 (clutch)
19Coolant temp (CLT)
20Inlet air temp (IAT)
21O2 sensor
22TPS input
23Ground
24Cam input / VR2+
25Crank input / VR1+
26VR2-
34Ignition 2
35Boost
36Idle 2 (3-wire idle)
37PWM idle
38VVT
OEM-4-U Injector 1 (cyl 1)
OEM-4-V Injector 2 (cyl 2)
OEM-4-W Injector 3 (cyl 3)
OEM-4-X Injector 4 (cyl 4)
OEM-4-N Ignition coil trigger (cyl 1&4)
GND
GND
OEM-3-H EGR boost sensor
0V sensor
5V ref
OEM-1-M Vehicle speed sensor (VSS)
OEM-1-B A/C condenser fan relay
OEM-1-A Cooling fan relay (low-side)
OEM-4-L Tachometer output
OEM-1-C Starter input (12V while cranking)
OEM-3-G Engine coolant temp (CLT)
OEM-3-K Intake air temp (IAT)
OEM-3-C Front O2 sensor input
OEM-3-F Throttle position (TPS)
0V sensor
OEM-4-G CAS SGC (cam sync)
OEM-4-E Crank position (CKP) sensor
OEM-4-F CAS SGT (cam trigger)
OEM-4-R Ignition coil trigger (cyl 2&3)
OEM-1-U Fuel pump relay (low-side)
OEM-1-G A/C clutch relay
OEM-3-M Front O2 heater control
OEM-1-E Check engine light (MIL)
SP-0V · 5 pins
SP-GND · 7 pins
Press enter or space to select a node. You can then use the arrow keys to move the node around. Press delete to remove it and escape to cancel.
Press enter or space to select an edge. You can then press delete to remove it or escape to cancel.