Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
100%
Stock ECU being replaced
GND
KV8-B-6 Injection 6
KV8-B-2 Injection 2
KV8-B-4 Injection 4
KV8-B-10 Aux 1
KV8-B-14 Aux 5
GND
KV8-B-26 Ignition 1
KV8-B-15 Aux 6
GND
KV8-C-4 Analog in 3
KV8-C-6 Analog in 5
0V sensor
KV8-C-2 Analog in 1
KV8-C-5 Analog in 4
KV8-B-12 Aux 3
ECU main power (from engine-electronics relay)
KV8-B-1 Injection 1
KV8-B-5 Injection 5
KV8-B-3 Injection 3
KV8-B-16 Aux 7
KV8-B-17 Aux 8
0V sensor
KV8-D-11 Knock 1 +
KV8-C-7 Analog in 6
KV8-C-28 Digital in 2
KV8-D-15 Ignition switch input
KV8-C-29 Digital in 3
KV8-C-3 Analog in 2
5V ref
KV8-D-6 Sync sensor +
KV8-D-9 EFI relay output (low side, 200 mA)
KV8-B-13 Aux 4
KV8-B-28 Ignition 3
KV8-B-11 Aux 2
GND
GND
KV8-B-27 Ignition 2
KV8-C-27 Digital in 1
0V sensor
KV8-D-4 Crank index sensor +
OEM-A
Stock ECU being replaced
1Ground (E-1)
2Injector 6 (cyl 6)
3Injector 2 (cyl 2)
4Injector 4 (cyl 4)
5Check engine light (MIL)
6Fuel pump relay control
7Ground (E-2)
8Ignition coil 2 (coil pack pin 2)
9Engine electronics relay control
10Ground (OBD1 EGR enable)
14Coolant temperature (CLT)
15EGR temperature sensor
16MAF ground
17MAF signal
20O2 sensor 1 (primary)
22Tachometer output
23ECU main power (from engine-electronics relay)
24Injector 1 (cyl 1)
25Injector 5 (cyl 5)
26Injector 3 (cyl 3)
27Idle air control valve
31EVAP canister purge valve
33Sensor ground bus
34Knock sensor 1
36Intake air temperature (IAT)
37A/C compressor switch
38Ignition switch (run/start)
39A/C switch (cabin)
40Throttle position sensor 1
41TPS power (+5V)
44Camshaft position sensor (G40)
49Secondary air injection relay control
51MFA fuel-consumption signal
52Ignition coil 4 (coil pack pin 4)
53Idle air control valve (2nd)
55Ground (E-3)
56Ground (E-4)
60Ignition coil 3 (coil pack pin 3)
65Vehicle speed sensor (VSS)
67Crank sensor return (VR-)
68Crank position sensor (G28, VR+)
KV8
KV8-A
KV8
KV8-B
KV8
1Injection 1
2Injection 2
3Injection 3
4Injection 4
5Injection 5
6Injection 6
9ECU ground
10Aux 1
11Aux 2
12Aux 3
13Aux 4
14Aux 5
15Aux 6
16Aux 7
17Aux 8
26Ignition 1
27Ignition 2
28Ignition 3
34ECU ground
OEM-A-24 Injector 1 (cyl 1)
OEM-A-3 Injector 2 (cyl 2)
OEM-A-26 Injector 3 (cyl 3)
OEM-A-4 Injector 4 (cyl 4)
OEM-A-25 Injector 5 (cyl 5)
OEM-A-2 Injector 6 (cyl 6)
GND
OEM-A-5 Check engine light (MIL)
OEM-A-53 Idle air control valve (2nd)
OEM-A-22 Tachometer output
OEM-A-51 MFA fuel-consumption signal
OEM-A-6 Fuel pump relay control
OEM-A-9 Engine electronics relay control
OEM-A-27 Idle air control valve
OEM-A-31 EVAP canister purge valve
OEM-A-8 Ignition coil 2 (coil pack pin 2)
OEM-A-60 Ignition coil 3 (coil pack pin 3)
OEM-A-52 Ignition coil 4 (coil pack pin 4)
GND
KV8-C
KV8
1ECU ground
2Analog in 1
3Analog in 2
4Analog in 3
5Analog in 4
6Analog in 5
7Analog in 6
17Analog sensor 0V reference
25Analog sensor 0V reference
26ECU ground
27Digital in 1
28Digital in 2
29Digital in 3
GND
OEM-A-17 MAF signal
OEM-A-40 Throttle position sensor 1
OEM-A-14 Coolant temperature (CLT)
OEM-A-20 O2 sensor 1 (primary)
OEM-A-15 EGR temperature sensor
OEM-A-36 Intake air temperature (IAT)
0V sensor
0V sensor
GND
OEM-A-65 Vehicle speed sensor (VSS)
OEM-A-37 A/C compressor switch
OEM-A-39 A/C switch (cabin)
KV8-D
KV8
1ECU 14V supply
2Aux 13–16 14V supply
4Crank index sensor +
5Crank index sensor −
6Sync sensor +
7Sync sensor −
9EFI relay output (low side, 200 mA)
11Knock 1 +
15Ignition switch input
20Aux 9–12 14V supply
21Sensor supply Vref1 5.0V
ECU 14V supply
Aux 13–16 14V supply
OEM-A-68 Crank position sensor (G28, VR+)
SP-0V · 3 pins
OEM-A-44 Camshaft position sensor (G40)
SP-0V · 3 pins
OEM-A-49 Secondary air injection relay control
OEM-A-34 Knock sensor 1
OEM-A-38 Ignition switch (run/start)
Aux 9–12 14V supply
5V ref
SP-GND · 10 pins
SP-0V · 8 pins
SP-14V · 5 pins
Press enter or space to select a node. You can then use the arrow keys to move the node around. Press delete to remove it and escape to cancel.
Press enter or space to select an edge. You can then press delete to remove it or escape to cancel.