Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
100%
Stock ECU being replaced
GND
M170-A-66 Peak Hold Injector 4
M170-A-43 Low Side Injector 1
M170-A-51 Low Side Injector 2
M170-A-42 Peak Hold Injector 6
GND
M170-A-1 Low Side Ignition 1
M170-A-57 Peak Hold Injector 7
GND
M170-A-28 Analogue Temperature Input 1
M170-A-38 Analogue Temperature Input 2
0V sensor
M170-A-26 Analogue Voltage Input 1
M170-A-6 Analogue Voltage Input 3
ECU main power (from engine-electronics relay)
M170-A-33 Peak Hold Injector 1
M170-A-63 Peak Hold Injector 3
M170-A-50 Peak Hold Injector 2
M170-A-62 Peak Hold Injector 8
0V sensor
M170-A-29 Knock Input 1
M170-A-30 Analogue Temperature Input 3
M170-A-45 Universal Digital Input 4
M170-A-52 Universal Digital Input 5
M170-A-18 Analogue Voltage Input 2
5V ref
M170-A-56 Universal Digital Input 2
M170-A-24 Peak Hold Injector 5
M170-A-4 Low Side Ignition 3
Battery constant (+12V)
GND
GND
M170-A-5 Low Side Ignition 2
M170-A-46 Universal Digital Input 3
0V sensor
M170-A-49 Universal Digital Input 1
OEM-A
Stock ECU being replaced
1Ground (E-1)
2Injector 6 (cyl 6)
3Injector 2 (cyl 2)
4Injector 4 (cyl 4)
6Fuel pump relay control
7Ground (E-2)
8Ignition coil 2 (coil pack pin 2)
9Engine electronics relay control
10Ground (OBD1 EGR enable)
14Coolant temperature (CLT)
15EGR temperature sensor
16MAF ground
17MAF signal
20O2 sensor 1 (primary)
23ECU main power (from engine-electronics relay)
24Injector 1 (cyl 1)
25Injector 5 (cyl 5)
26Injector 3 (cyl 3)
27Idle air control valve
33Sensor ground bus
34Knock sensor 1
36Intake air temperature (IAT)
37A/C compressor switch
39A/C switch (cabin)
40Throttle position sensor 1
41TPS power (+5V)
44Camshaft position sensor (G40)
49Secondary air injection relay control
52Ignition coil 4 (coil pack pin 4)
54Battery constant (+12V)
55Ground (E-3)
56Ground (E-4)
60Ignition coil 3 (coil pack pin 3)
65Vehicle speed sensor (VSS)
67Crank sensor return (VR-)
68Crank position sensor (G28, VR+)
M170
M170-A
M170
1Low Side Ignition 1
4Low Side Ignition 3
5Low Side Ignition 2
6Analogue Voltage Input 3
11Sensor 0V A
14Battery Negative 1
15Battery Negative 2
16Sensor 5.0V A
18Analogue Voltage Input 2
19Battery Negative 3
20Battery Negative 4
21Battery Negative 5
23Battery Positive
24Peak Hold Injector 5
26Analogue Voltage Input 1
27Sensor 0V B
28Analogue Temperature Input 1
29Knock Input 1
30Analogue Temperature Input 3
32Battery Positive
33Peak Hold Injector 1
38Analogue Temperature Input 2
41Battery Positive
42Peak Hold Injector 6
43Low Side Injector 1
45Universal Digital Input 4
46Universal Digital Input 3
49Universal Digital Input 1
50Peak Hold Injector 2
51Low Side Injector 2
52Universal Digital Input 5
54Battery Backup
56Universal Digital Input 2
57Peak Hold Injector 7
62Peak Hold Injector 8
63Peak Hold Injector 3
66Peak Hold Injector 4
OEM-A-8 Ignition coil 2 (coil pack pin 2)
OEM-A-52 Ignition coil 4 (coil pack pin 4)
OEM-A-60 Ignition coil 3 (coil pack pin 3)
OEM-A-20 O2 sensor 1 (primary)
0V sensor
GND
GND
5V ref
OEM-A-40 Throttle position sensor 1
GND
GND
GND
Battery Positive
OEM-A-49 Secondary air injection relay control
OEM-A-17 MAF signal
0V sensor
OEM-A-14 Coolant temperature (CLT)
OEM-A-34 Knock sensor 1
OEM-A-36 Intake air temperature (IAT)
Battery Positive
OEM-A-24 Injector 1 (cyl 1)
OEM-A-15 EGR temperature sensor
Battery Positive
OEM-A-6 Fuel pump relay control
OEM-A-3 Injector 2 (cyl 2)
OEM-A-37 A/C compressor switch
OEM-A-65 Vehicle speed sensor (VSS)
OEM-A-68 Crank position sensor (G28, VR+)
OEM-A-26 Injector 3 (cyl 3)
OEM-A-4 Injector 4 (cyl 4)
OEM-A-39 A/C switch (cabin)
Battery Backup
OEM-A-44 Camshaft position sensor (G40)
OEM-A-9 Engine electronics relay control
OEM-A-27 Idle air control valve
OEM-A-25 Injector 5 (cyl 5)
OEM-A-2 Injector 6 (cyl 6)
SP-GND · 11 pins
SP-0V · 6 pins
SP-14V · 5 pins
Press enter or space to select a node. You can then use the arrow keys to move the node around. Press delete to remove it and escape to cancel.
Press enter or space to select an edge. You can then press delete to remove it or escape to cancel.