Lengths need a layout. Add bundles in Layout.
Not set yet: signal, colour, stripe, ident. Show
W1
OEM-A-14 ECU power (control-unit relay) → SP-14V-1
0.85 mm² (≈18 AWG)
W2
SP-14V-1 → P8-C1-19 12 Volts
0.85 mm² (≈18 AWG)
W3
OEM-A-13 Ground → SP-GND-1
0.85 mm² (≈18 AWG)
W4
OEM-A-19 Ground → SP-GND-1
0.85 mm² (≈18 AWG)
W5
SP-GND-1 → P8-C1-15 Power Ground
0.85 mm² (≈18 AWG)
W6
SP-GND-1 → P8-C1-34 Power Ground
0.85 mm² (≈18 AWG)
W7
SP-GND-1 → P8-C1-55 Power Ground
0.85 mm² (≈18 AWG)
W8
OEM-A-5 Knock sensor return → SP-0V-1
0.5 mm² (≈20 AWG)
W9
OEM-A-6 Sensor ground (CTS/Hall/AFM/throttle) → SP-0V-1
0.5 mm² (≈20 AWG)
W10
SP-0V-1 → P8-C1-46 Signal Ground
0.5 mm² (≈20 AWG)
W11
SP-0V-1 → P8-C1-47 Signal Ground
0.5 mm² (≈20 AWG)
W12
SP-0V-1 → P8-C1-49 Lambda Earth
0.5 mm² (≈20 AWG)
W13
SP-0V-1 → P8-C1-51 Signal Ground
0.5 mm² (≈20 AWG)
W14
OEM-A-17 AFM potentiometer supply → P8-C1-10 5 Volts
0.5 mm² (≈20 AWG)
W15
OEM-A-18 Hall sender signal (engine speed) → P8-C1-27 Cam Sensor
0.5 mm² (≈20 AWG)
W16
OEM-A-25 Ignition timing signal to TCI → P8-C1-1 Coil 1
0.5 mm² (≈20 AWG)
W17
OEM-A-12 Injector driver (batch, all 4) → P8-C1-37 Injector 1
0.5 mm² (≈20 AWG)
W18
OEM-A-3 Fuel pump relay control → P8-C1-41 Fuel Pump Relay
0.5 mm² (≈20 AWG)
W19
OEM-A-21 AFM signal → P8-C1-25 Analogue Input 1
0.5 mm² (≈20 AWG)
W20
OEM-A-10 Coolant temperature sensor → P8-C1-26 Water Temp
0.5 mm² (≈20 AWG)
W21
OEM-A-22 Idle stabilizer valve coil 1 → P8-C1-4 Idle Valve
0.5 mm² (≈20 AWG)
W22
OEM-A-23 Idle stabilizer valve coil 2 → P8-C1-42 Cam Phase Valve/Aux Out 4
0.5 mm² (≈20 AWG)
W23
OEM-A-2 Oxygen (lambda) sensor signal → P8-C1-12 Lambda Signal
0.5 mm² (≈20 AWG)
W24
OEM-A-9 Intake air temperature sensor → P8-C1-45 Air Temp
0.5 mm² (≈20 AWG)
W25
OEM-A-1 Starter signal (term 50) → P8-C1-13 Map2/ALS/Ana1 On/Off
0.5 mm² (≈20 AWG)
W26
OEM-A-11 Idle/WOT throttle switch → P8-C1-14 Traction Wet/Dry
0.5 mm² (≈20 AWG)
W27
OEM-A-16 A/C compressor signal → P8-C1-31 Launch Button
0.5 mm² (≈20 AWG)