Lengths need a layout. Add bundles in Layout.
Not set yet: signal, colour, stripe, ident. Show
W1
OEM-A-2 Ignition power 2 → SP-14V-1
0.85 mm² (≈18 AWG)
W2
OEM-A-3 Ignition power 1 → SP-14V-1
0.85 mm² (≈18 AWG)
W3
SP-14V-1 → MICROSQUIRT-A-1 +12V In
0.85 mm² (≈18 AWG)
W4
OEM-A-4 Power ground 2 → SP-GND-1
0.85 mm² (≈18 AWG)
W5
OEM-A-5 Power ground 1 → SP-GND-1
0.85 mm² (≈18 AWG)
W6
OEM-A-8 Logic ground 2 → SP-GND-1
0.85 mm² (≈18 AWG)
W7
OEM-A-9 Logic ground 1 → SP-GND-1
0.85 mm² (≈18 AWG)
W8
OEM-E-3 Logic ground 3 → SP-GND-1
0.85 mm² (≈18 AWG)
W9
SP-GND-1 → MICROSQUIRT-A-22 POWER GROUND
0.85 mm² (≈18 AWG)
W10
SP-GND-1 → MICROSQUIRT-A-23 POWER GROUND
0.85 mm² (≈18 AWG)
W11
OEM-A-23 Sensor ground 2 → SP-0V-1
0.5 mm² (≈20 AWG)
W12
OEM-A-24 Sensor ground 1 → SP-0V-1
0.5 mm² (≈20 AWG)
W13
OEM-E-4 Sensor ground 3 → SP-0V-1
0.5 mm² (≈20 AWG)
W14
TB-J-GND Throttle sensor ground → SP-0V-1
0.5 mm² (≈20 AWG)
W15
SP-0V-1 → MICROSQUIRT-A-18 Sensor Ground
0.5 mm² (≈20 AWG)
W16
SP-0V-1 → MICROSQUIRT-A-19 Serial Ground
0.5 mm² (≈20 AWG)
W17
SP-0V-1 → MICROSQUIRT-A-20 Sensor Ground
0.5 mm² (≈20 AWG)
W18
OEM-A-20 Sensor voltage 2 → SP-5V1-1
0.5 mm² (≈20 AWG)
W19
OEM-A-21 Sensor voltage 1 → SP-5V1-1
0.5 mm² (≈20 AWG)
W20
OEM-E-5 Sensor voltage 3 → SP-5V1-1
0.5 mm² (≈20 AWG)
W21
TB-J-VCC Throttle sensor 5V supply → SP-5V1-1
0.5 mm² (≈20 AWG)
W22
SP-5V1-1 → MICROSQUIRT-A-28 TPS VREF (5V)
0.5 mm² (≈20 AWG)
W23
OEM-A-7 Crank position sensor (T1) → MICROSQUIRT-A-32 VR1+
0.5 mm² (≈20 AWG)
W24
OEM-A-6 Cam position sensor (T2) → MICROSQUIRT-A-4 VR2+
0.5 mm² (≈20 AWG)
W25
OEM-A-16 Ignition coil 1 → MICROSQUIRT-A-11 SPK B (IGN2)
0.5 mm² (≈20 AWG)
W26
OEM-A-15 Ignition coil 2 → MICROSQUIRT-A-12 SPK A (IGN 1)
0.5 mm² (≈20 AWG)
W27
OEM-B-5 Injector 1 → MICROSQUIRT-A-9 INJ 1
0.5 mm² (≈20 AWG)
W28
OEM-B-4 Injector 2 → MICROSQUIRT-A-10 INJ 2
0.5 mm² (≈20 AWG)
W29
OEM-B-3 Injector 3 → MICROSQUIRT-A-9 INJ 1
0.5 mm² (≈20 AWG)
W30
OEM-B-2 Injector 4 → MICROSQUIRT-A-10 INJ 2
0.5 mm² (≈20 AWG)
W31
OEM-E-17 Fuel pump relay → MICROSQUIRT-A-8 FP (pump)
0.5 mm² (≈20 AWG)
W32
OEM-E-7 Main relay control → MICROSQUIRT-A-16 ALED
0.5 mm² (≈20 AWG)
W33
OEM-B-6 VTEC solenoid → RLY1-R-OUT Relay contact output (switched +12 V to load)
0.5 mm² (≈20 AWG)
W34
SP-14V-1 → RLY1-R-IN Relay contact input (switched +12 V)
0.5 mm² (≈20 AWG)
W35
SP-14V-1 → RLY1-R-COIL+ Relay coil positive (switched +12 V)
0.5 mm² (≈20 AWG)
W36
RLY1-R-COIL- Relay coil negative (ECU low-side driver) → MICROSQUIRT-A-17 WLED
0.5 mm² (≈20 AWG)
W37
OEM-A-30 MAP sensor → MICROSQUIRT-A-24 MAP
0.5 mm² (≈20 AWG)
W38
OEM-A-25 Accelerator pedal position B → MICROSQUIRT-A-27 TPS
0.5 mm² (≈20 AWG)
W39
OEM-A-26 Accelerator pedal position A → MICROSQUIRT-A-5 SPAREADC2 (MAF)
0.5 mm² (≈20 AWG)
W40
OEM-B-8 Coolant temp sensor → MICROSQUIRT-A-25 CLT
0.5 mm² (≈20 AWG)
W41
TB-J-TPS1 Throttle position 1 → MICROSQUIRT-A-29 SPAREADC
0.5 mm² (≈20 AWG)
W42
OEM-D-15 Throttle actuator relay → MICROSQUIRT-A-7 FIDLE
0.5 mm² (≈20 AWG)
W43
OEM-E-25 Engine speed pulse (tacho) → MICROSQUIRT-A-35 TACHO
0.5 mm² (≈20 AWG)
W44
OEM-E-20 Secondary O2 sensor → MICROSQUIRT-A-34 O2
0.5 mm² (≈20 AWG)
W45
OEM-E-1 Coolant temp sensor 2 → MICROSQUIRT-A-26 MAT
0.5 mm² (≈20 AWG)
W46
OEM-A-18 Vehicle speed sensor → MICROSQUIRT-A-30 OPTO+
0.5 mm² (≈20 AWG)
W47
OEM-B-11 VTEC oil pressure switch → MICROSQUIRT-A-31 OPTO-
0.5 mm² (≈20 AWG)
W48
OEM-D-1 Cruise set switch → MICROSQUIRT-A-6 FLEX
0.5 mm² (≈20 AWG)
W49
OEM-E-11 CAN H → MICROSQUIRT-A-2 CANH
0.5 mm² (≈20 AWG)
W50
OEM-E-24 CAN L → MICROSQUIRT-A-3 CANL
0.5 mm² (≈20 AWG)