Not confident with automotive wiring? Have a professional harness builder or tuner do it, or check your work before first power-up. A wiring mistake can damage the ECU, the engine or the car, or start a fire.
100%
Stock ECU being replaced
FT450-A-A2 Injector 2 (Bank A)
FT450-A-A1 Injector 1 (Bank A)
FT450-A-A1 Injector 1 (Bank A)
GND
OEM-A
Stock ECU being replaced
11Injectors 2 & 6 (No.20)
12Injectors 1 & 4 (No.10)
25Injectors 3 & 5 (No.30)
26Power ground (E01/E02)
FT450-A-A24 White input 5 (water temp)
FT450-A-A21 White input 2
0V sensor
FT450-A-A20 White input 1
OEM-B
Stock ECU being replaced
4Coolant temp (THW)
6Primary O2 sensor (OX1)
9Sensor ground (E1)
11Throttle position sensor (VTA)
FT450-A-A26 White input 7 (air temp)
FT450-A-A3 Aux 1
FT450-A-A22 White input 3 (TPS)
FT450-A-A23 White input 4 (oil pressure)
EFI main relay power (+B)
EFI main relay power (second feed) (+B1)
FT450-A-A25 White input 6 (fuel pressure)
OEM-D
Stock ECU being replaced
3Intake air temp (THA)
4EFI main relay control (M-REL)
10A/C compressor request (A/C)
11Starter signal (STA)
12EFI main relay power (+B)
13EFI main relay power (second feed) (+B1)
22Neutral start switch (NSW)
FT450
FT450-A
FT450
A1Injector 1 (Bank A)
A2Injector 2 (Bank A)
A3Aux 1
A6Aux 4 (fuel pump / relays)
A7Power ground
A12Signal ground
A13+12V switched
A20White input 1
A21White input 2
A22White input 3 (TPS)
A23White input 4 (oil pressure)
A24White input 5 (water temp)
A25White input 6 (fuel pressure)
A26White input 7 (air temp)
Injectors 3 & 5 (No.30) · 2 pins
OEM-A-11 Injectors 2 & 6 (No.20)
OEM-D-4 EFI main relay control (M-REL)
NEW-FUELPUMP
GND
0V sensor
+12V switched
OEM-B-11 Throttle position sensor (VTA)
OEM-B-6 Primary O2 sensor (OX1)
OEM-D-10 A/C compressor request (A/C)
OEM-D-11 Starter signal (STA)
OEM-B-4 Coolant temp (THW)
OEM-D-22 Neutral start switch (NSW)
OEM-D-3 Intake air temp (THA)
MAIN
MAIN-R
MAIN
INRelay contact input (battery + via main fuse)
OUTRelay contact output (switched +12V bus)
COIL+Relay coil positive (ignition-switched +12V)
COIL-Relay coil negative (ECU low-side driver)
NEW-BATT
FT450-A-A13 +12V switched
Relay coil positive (ignition-switched +12V)
SP-GND · 2 pins
◯New feed: NEW-FUELPUMP
SP-0V · 3 pins
SP-GND · 4 pins
SP-14V · 3 pins
◯New feed: NEW-BATT
◯New feed: NEW-KEYON
Press enter or space to select a node. You can then use the arrow keys to move the node around. Press delete to remove it and escape to cancel.
Press enter or space to select an edge. You can then press delete to remove it or escape to cancel.