Lengths need a layout. Add bundles in Layout.
Not set yet: signal, colour, stripe, ident. Show
W1
OEM-D-12 EFI main relay power (+B) → SP-14V-1
0.85 mm² (≈18 AWG)
W2
OEM-D-13 EFI main relay power (second feed) (+B1) → SP-14V-1
0.85 mm² (≈18 AWG)
W3
NEW-KEYON-1 → MAIN-R-COIL+ Relay coil positive (ignition-switched +12V)
0.5 mm² (≈20 AWG)
W4
NEW-BATT-1 → MAIN-R-IN Relay contact input (battery + via main fuse)
0.85 mm² (≈18 AWG)
W5
MAIN-R-COIL- Relay coil negative (ECU low-side driver) → SP-GND-1
0.5 mm² (≈20 AWG)
W6
MAIN-R-OUT Relay contact output (switched +12V bus) → NEXUSS3-A-18 +12V switched input
0.85 mm² (≈18 AWG)
W7
MAIN-R-OUT Relay contact output (switched +12V bus) → NEXUSS3-A-25 +12V switched input
0.85 mm² (≈18 AWG)
W8
OEM-A-26 Power ground (E01/E02) → SP-GND-1
0.85 mm² (≈18 AWG)
W9
SP-GND-1 → NEXUSS3-A-10 Battery ground
0.85 mm² (≈18 AWG)
W10
SP-GND-1 → NEXUSS3-A-11 Battery ground
0.85 mm² (≈18 AWG)
W11
OEM-B-9 Sensor ground (E1) → SP-0V-1
0.5 mm² (≈20 AWG)
W12
SP-0V-1 → NEXUSS3-C-26 Signal ground
0.5 mm² (≈20 AWG)
W13
OEM-D-5 Knock sensor 1 (KNK1) → NEXUSS3-C-23 Knock 1
0.5 mm² (≈20 AWG)
W14
OEM-A-12 Injectors 1 & 4 (No.10) → NEXUSS3-A-1 Injector 1
0.5 mm² (≈20 AWG)
W15
OEM-A-11 Injectors 2 & 6 (No.20) → NEXUSS3-A-2 Injector 2
0.5 mm² (≈20 AWG)
W16
OEM-A-25 Injectors 3 & 5 (No.30) → NEXUSS3-A-3 Injector 3
0.5 mm² (≈20 AWG)
W17
OEM-D-4 EFI main relay control (M-REL) → NEXUSS3-A-26 ECR output
0.5 mm² (≈20 AWG)
W18
OEM-B-11 Throttle position sensor (VTA) → NEXUSS3-C-10 AVI 1
0.5 mm² (≈20 AWG)
W19
OEM-B-4 Coolant temp (THW) → NEXUSS3-C-11 AVI 2
0.5 mm² (≈20 AWG)
W20
OEM-D-2 Karman-vortex AFM signal (KS) → NEXUSS3-C-5 SPI 1
0.5 mm² (≈20 AWG)
W21
OEM-B-6 Primary O2 sensor (OX1) → NEXUSS3-C-12 AVI 3
0.5 mm² (≈20 AWG)
W22
OEM-D-3 Intake air temp (THA) → NEXUSS3-C-13 AVI 4
0.5 mm² (≈20 AWG)
W23
OEM-D-9 Vehicle speed sensor (SPD) → NEXUSS3-C-6 SPI 2
0.5 mm² (≈20 AWG)
W24
OEM-D-10 A/C compressor request (A/C) → NEXUSS3-C-7 SPI 3
0.5 mm² (≈20 AWG)
W25
OEM-D-11 Starter signal (STA) → NEXUSS3-C-8 SPI 4
0.5 mm² (≈20 AWG)
W26
OEM-D-22 Neutral start switch (NSW) → NEXUSS3-C-19 SPI 5
0.5 mm² (≈20 AWG)
W27
NEW-KEYON-1 → NEXUSS3-A-13 Ignition switch input
0.5 mm² (≈20 AWG)