Lengths need a layout. Add bundles in Layout.
Not set yet: signal, colour, stripe, ident. Show
W1
OEM-B-1 Power source 1 (main relay) → SP-14V-1
0.85 mm² (≈18 AWG)
W2
OEM-B-9 Power source 2 (main relay) → SP-14V-1
0.85 mm² (≈18 AWG)
W3
SP-14V-1 → P8-C1-19 12 Volts
0.85 mm² (≈18 AWG)
W4
OEM-B-10 Power ground 2 → SP-GND-1
0.85 mm² (≈18 AWG)
W5
OEM-B-2 Power ground 1 → SP-GND-1
0.85 mm² (≈18 AWG)
W6
OEM-B-20 Ground → SP-GND-1
0.85 mm² (≈18 AWG)
W7
OEM-B-22 Ground → SP-GND-1
0.85 mm² (≈18 AWG)
W8
SP-GND-1 → P8-C1-15 Power Ground
0.85 mm² (≈18 AWG)
W9
SP-GND-1 → P8-C1-34 Power Ground
0.85 mm² (≈18 AWG)
W10
SP-GND-1 → P8-C1-55 Power Ground
0.85 mm² (≈18 AWG)
W11
OEM-C-18 Sensor ground 2 → SP-0V-1
0.5 mm² (≈20 AWG)
W12
OEM-C-30 Cam (TDC2) sensor − → SP-0V-1
0.5 mm² (≈20 AWG)
W13
OEM-C-31 Timing ground → SP-0V-1
0.5 mm² (≈20 AWG)
W14
OEM-C-7 Sensor ground 1 → SP-0V-1
0.5 mm² (≈20 AWG)
W15
SP-0V-1 → P8-C1-46 Signal Ground
0.5 mm² (≈20 AWG)
W16
SP-0V-1 → P8-C1-47 Signal Ground
0.5 mm² (≈20 AWG)
W17
SP-0V-1 → P8-C1-49 Lambda Earth
0.5 mm² (≈20 AWG)
W18
SP-0V-1 → P8-C1-51 Signal Ground
0.5 mm² (≈20 AWG)
W19
OEM-C-19 Sensor 5V supply 1 (MAP) → P8-C1-10 5 Volts
0.5 mm² (≈20 AWG)
W20
OEM-C-28 Sensor 5V supply 2 → P8-C1-28 5 Volts
0.5 mm² (≈20 AWG)
W21
OEM-C-8 Crank sensor + (CKP+) → P8-C1-8 Crank Sensor
0.5 mm² (≈20 AWG)
W22
OEM-C-9 Crank sensor − (CKP−) → SP-0V-1
0.5 mm² (≈20 AWG)
W23
OEM-C-20 Cam (TDC1) sensor + → P8-C1-27 Cam Sensor
0.5 mm² (≈20 AWG)
W24
OEM-C-21 Cam (TDC1) sensor − → SP-0V-1
0.5 mm² (≈20 AWG)
W25
OEM-C-29 Cam (TDC2) sensor + → P8-C1-29 Left Driven Wheel
0.5 mm² (≈20 AWG)
W26
OEM-C-4 Ignition coil 1 → P8-C1-1 Coil 1
0.5 mm² (≈20 AWG)
W27
OEM-C-12 Ignition coil 2 → P8-C1-38 Coil 2
0.5 mm² (≈20 AWG)
W28
OEM-C-13 Ignition coil 3 → P8-C1-20 Coil 3
0.5 mm² (≈20 AWG)
W29
OEM-C-14 Ignition coil 4 → P8-C1-2 Coil 4
0.5 mm² (≈20 AWG)
W30
OEM-B-11 Injector 1 → P8-C1-37 Injector 1
0.5 mm² (≈20 AWG)
W31
OEM-B-3 Injector 2 → P8-C1-18 Injector 2
0.5 mm² (≈20 AWG)
W32
OEM-B-4 Injector 3 → P8-C1-54 Injector 3
0.5 mm² (≈20 AWG)
W33
OEM-B-5 Injector 4 → P8-C1-36 Injector 4
0.5 mm² (≈20 AWG)
W34
OEM-A-15 Fuel pump relay (USDM) → P8-C1-41 Fuel Pump Relay
0.5 mm² (≈20 AWG)
W35
OEM-B-12 VTEC solenoid → RLY1-R-OUT Relay contact output (switched +12 V to load)
0.5 mm² (≈20 AWG)
W36
SP-14V-1 → RLY1-R-IN Relay contact input (switched +12 V)
0.5 mm² (≈20 AWG)
W37
SP-14V-1 → RLY1-R-COIL+ Relay coil positive (switched +12 V)
0.5 mm² (≈20 AWG)
W38
RLY1-R-COIL- Relay coil negative (ECU low-side driver) → P8-C1-5 Aux Out 2
0.5 mm² (≈20 AWG)
W39
OEM-C-17 MAP sensor → P8-C1-30 Map
0.5 mm² (≈20 AWG)
W40
OEM-C-27 Throttle position sensor → P8-C1-48 Throttle Wiper
0.5 mm² (≈20 AWG)
W41
OEM-C-26 Coolant temp sensor → P8-C1-26 Water Temp
0.5 mm² (≈20 AWG)
W42
OEM-A-16 Fuel pump relay (JDM) → P8-C1-43 Aux Out 3
0.5 mm² (≈20 AWG)
W43
OEM-A-17 A/C clutch relay → P8-C1-42 Cam Phase Valve/Aux Out 4
0.5 mm² (≈20 AWG)
W44
OEM-A-20 Radiator fan relay → P8-C1-21 Turbo Pressure Valve
0.5 mm² (≈20 AWG)
W45
OEM-A-28 Air pump relay → P8-C1-23 Turbo ALS Valve
0.5 mm² (≈20 AWG)
W46
OEM-C-1 Primary O2 heater → P8-C1-4 Idle Valve
0.5 mm² (≈20 AWG)
W47
OEM-C-11 Secondary O2 heater control → P8-C1-6 Shift Light
0.5 mm² (≈20 AWG)
W48
OEM-B-23 Idle air control valve → P8-C1-17 Injector 5
0.5 mm² (≈20 AWG)
W49
OEM-A-1 Coolant temp gauge drive → P8-C1-35 Injector 6
0.5 mm² (≈20 AWG)
W50
OEM-A-12 Immobilizer indicator light → P8-C1-53 Injector 7
0.5 mm² (≈20 AWG)
W51
OEM-A-18 Check engine light (MIL) → P8-C1-16 Injector 8
0.5 mm² (≈20 AWG)
W52
OEM-A-19 Tacho output → P8-C1-24 Tacho
0.5 mm² (≈20 AWG)
W53
OEM-A-23 Secondary O2 sensor → P8-C1-12 Lambda Signal
0.5 mm² (≈20 AWG)
W54
OEM-C-15 Secondary O2 sensor → P8-C1-25 Analogue Input 1
0.5 mm² (≈20 AWG)
W55
OEM-C-16 Primary O2 sensor → P8-C1-7 Analogue Input 2 Or Log Switch
0.5 mm² (≈20 AWG)
W56
OEM-C-25 Intake air temp sensor → P8-C1-45 Air Temp
0.5 mm² (≈20 AWG)
W57
OEM-A-29 Fuel tank pressure sensor → P8-C1-44 Analogue Input 3
0.5 mm² (≈20 AWG)
W58
OEM-A-9 Vehicle speed sensor → P8-C1-11 Undriven Wheel (must)
0.5 mm² (≈20 AWG)
W59
OEM-C-5 Alternator FR signal → P8-C1-50 Undriven Wheel (optional)
0.5 mm² (≈20 AWG)
W60
OEM-A-24 Starter switch signal → P8-C1-13 Map2/ALS/Ana1 On/Off
0.5 mm² (≈20 AWG)
W61
OEM-A-26 Power steering load detect → P8-C1-14 Traction Wet/Dry
0.5 mm² (≈20 AWG)
W62
OEM-A-27 A/C switch (request) → P8-C1-31 Launch Button
0.5 mm² (≈20 AWG)
W63
OEM-A-32 Brake switch → P8-C1-32 Traction On/Off
0.5 mm² (≈20 AWG)
W64
OEM-C-10 VTEC pressure switch → P8-C1-33 Shift Cut
0.5 mm² (≈20 AWG)