Lengths need a layout. Add bundles in Layout.
Not set yet: signal, colour, stripe, ident. Show
W1
OEM-4-B ECU power +12V (main relay) → SP-14V-1
0.85 mm² (≈18 AWG)
W2
SP-14V-1 → ME442-C1-15 IGN +12V
0.85 mm² (≈18 AWG)
W3
SP-14V-1 → ME442-C1-64 VBAT
0.85 mm² (≈18 AWG)
W4
OEM-4-A Chassis ground → SP-GND-1
0.85 mm² (≈18 AWG)
W5
OEM-4-C Chassis ground → SP-GND-1
0.85 mm² (≈18 AWG)
W6
OEM-4-D Chassis ground → SP-GND-1
0.85 mm² (≈18 AWG)
W7
OEM-4-K Chassis ground → SP-GND-1
0.85 mm² (≈18 AWG)
W8
SP-GND-1 → ME442-C1-10 GROUND CHASSIS
0.85 mm² (≈18 AWG)
W9
SP-GND-1 → ME442-C1-61 GROUND
0.85 mm² (≈18 AWG)
W10
SP-GND-1 → ME442-C1-89 GROUND
0.85 mm² (≈18 AWG)
W11
SP-GND-1 → ME442-C1-90 GROUND
0.85 mm² (≈18 AWG)
W12
OEM-3-O Sensor ground → SP-0V-1
0.5 mm² (≈20 AWG)
W13
OEM-4-H Crank pickup timing ground (CKP gnd) → SP-0V-1
0.5 mm² (≈20 AWG)
W14
SP-0V-1 → ME442-C1-52 SENSORS GROUND
0.5 mm² (≈20 AWG)
W15
SP-0V-1 → ME442-C1-84 Sensor Ground
0.5 mm² (≈20 AWG)
W16
OEM-3-I +5V sensor reference → ME442-C1-45 5V REF
0.5 mm² (≈20 AWG)
W17
OEM-4-E Crank position (CKP) sensor → ME442-C1-80 CRANK VR+
0.5 mm² (≈20 AWG)
W18
OEM-4-G CAS SGC (cam sync) → ME442-C1-22 CAM A VR+
0.5 mm² (≈20 AWG)
W19
OEM-4-F CAS SGT (cam trigger) → ME442-C1-23 CAM A VR-
0.5 mm² (≈20 AWG)
W20
OEM-4-N Ignition coil trigger (cyl 1&4) → ME442-C1-32 COIL 1
0.5 mm² (≈20 AWG)
W21
OEM-4-R Ignition coil trigger (cyl 2&3) → ME442-C1-31 COIL 2
0.5 mm² (≈20 AWG)
W22
OEM-4-U Injector 1 (cyl 1) → ME442-C1-63 INJECTOR 1
0.5 mm² (≈20 AWG)
W23
OEM-4-V Injector 2 (cyl 2) → ME442-C1-4 INJECTOR 2
0.5 mm² (≈20 AWG)
W24
OEM-4-W Injector 3 (cyl 3) → ME442-C1-33 INJECTOR 3
0.5 mm² (≈20 AWG)
W25
OEM-4-X Injector 4 (cyl 4) → ME442-C1-3 INJECTOR 4
0.5 mm² (≈20 AWG)
W26
OEM-3-B MAF sensor input → ME442-C1-26 ANA VOLT 1
0.5 mm² (≈20 AWG)
W27
OEM-3-F Throttle position (TPS) → ME442-C1-56 ANA VOLT 2
0.5 mm² (≈20 AWG)
W28
OEM-3-G Engine coolant temp (CLT) → ME442-C1-86 ANA TEMP 1
0.5 mm² (≈20 AWG)
W29
OEM-1-A Cooling fan relay (low-side) → ME442-C1-73 LOW SIDE 1
0.5 mm² (≈20 AWG)
W30
OEM-1-B A/C condenser fan relay → ME442-C1-12 LOW SIDE 2
0.5 mm² (≈20 AWG)
W31
OEM-1-G A/C clutch relay → ME442-C1-74 LOW SIDE 3
0.5 mm² (≈20 AWG)
W32
OEM-1-U Fuel pump relay (low-side) → ME442-C1-44 LOW SIDE 4
0.5 mm² (≈20 AWG)
W33
OEM-3-M Front O2 heater control → ME442-C1-16 LSU HEATER -VE
0.5 mm² (≈20 AWG)
W34
OEM-1-E Check engine light (MIL) → ME442-C1-69 LOW SIDE 5
0.5 mm² (≈20 AWG)
W35
OEM-4-J PRC solenoid (FPR control) → ME442-C1-39 LOW SIDE 6
0.5 mm² (≈20 AWG)
W36
OEM-4-O EGR vent solenoid → ME442-C1-37 LOW SIDE RELAY 11
0.5 mm² (≈20 AWG)
W37
OEM-4-P EGR vacuum solenoid → ME442-C1-42 LOW SIDE RELAY 12
0.5 mm² (≈20 AWG)
W38
OEM-4-Q Idle air control (IAC) valve → ME442-C1-72 LOW SIDE RELAY 13
0.5 mm² (≈20 AWG)
W39
OEM-4-T EVAP purge solenoid → ME442-C1-43 LOW SIDE RELAY 14
0.5 mm² (≈20 AWG)
W40
OEM-4-L Tachometer output → ME442-C1-79 TACHOMETER
0.5 mm² (≈20 AWG)
W41
OEM-3-H EGR boost sensor → ME442-C1-17 ANA VOLT 3
0.5 mm² (≈20 AWG)
W42
OEM-3-N EGR boost sensor (2nd channel) → ME442-C1-18 ANA VOLT 4
0.5 mm² (≈20 AWG)
W43
OEM-3-C Front O2 sensor input → ME442-C1-87 ANA VOLT 5
0.5 mm² (≈20 AWG)
W44
OEM-3-D Rear O2 sensor input → ME442-C1-78 ANA VOLT 6
0.5 mm² (≈20 AWG)
W45
OEM-3-K Intake air temp (IAT) → ME442-C1-57 ANA TEMP 2
0.5 mm² (≈20 AWG)
W46
OEM-3-J EGR valve position sensor → ME442-C1-48 ANA VOLT 7
0.5 mm² (≈20 AWG)
W47
OEM-1-M Vehicle speed sensor (VSS) → ME442-C1-6 DIG_IN 1
0.5 mm² (≈20 AWG)
W48
OEM-1-C Starter input (12V while cranking) → ME442-C1-7 DIG_IN 2
0.5 mm² (≈20 AWG)
W49
OEM-1-K A/C pressure switch (A/C request) → ME442-C1-8 DIG_IN 3
0.5 mm² (≈20 AWG)
W50
OEM-1-L Clutch switch → ME442-C1-5 DIG_IN 4
0.5 mm² (≈20 AWG)
W51
OEM-1-Q Brake switch → ME442-C1-62 DIG_IN 5
0.5 mm² (≈20 AWG)
W52
OEM-3-L Idle switch (closed throttle) → ME442-C1-34 DIG_IN 6
0.5 mm² (≈20 AWG)