Lengths need a layout. Add bundles in Layout.
Not set yet: signal, colour, stripe, ident. Show
W1
OEM-C86-22 EFI main relay power (+B) → SP-14V-1
0.85 mm² (≈18 AWG)
W2
OEM-C86-23 EFI main relay power (+B1) → SP-14V-1
0.85 mm² (≈18 AWG)
W3
SP-14V-1 → ME442-C1-15 IGN +12V
0.85 mm² (≈18 AWG)
W4
SP-14V-1 → ME442-C1-64 VBAT
0.85 mm² (≈18 AWG)
W5
OEM-C85-16 Power ground (E1) → SP-GND-1
0.85 mm² (≈18 AWG)
W6
OEM-C88-28 Power ground (E11) → SP-GND-1
0.85 mm² (≈18 AWG)
W7
OEM-C88-33 Power ground (E02) → SP-GND-1
0.85 mm² (≈18 AWG)
W8
OEM-C88-34 Power ground (E01) → SP-GND-1
0.85 mm² (≈18 AWG)
W9
SP-GND-1 → ME442-C1-10 GROUND CHASSIS
0.85 mm² (≈18 AWG)
W10
SP-GND-1 → ME442-C1-61 GROUND
0.85 mm² (≈18 AWG)
W11
SP-GND-1 → ME442-C1-89 GROUND
0.85 mm² (≈18 AWG)
W12
SP-GND-1 → ME442-C1-90 GROUND
0.85 mm² (≈18 AWG)
W13
OEM-C84-11 Cam 1 return (G1-) → SP-0V-1
0.5 mm² (≈20 AWG)
W14
OEM-C84-17 Cam 2 return (G2-) → SP-0V-1
0.5 mm² (≈20 AWG)
W15
OEM-C84-22 Sensor ground (E2) → SP-0V-1
0.5 mm² (≈20 AWG)
W16
OEM-C84-6 Crank sensor return (NE-) → SP-0V-1
0.5 mm² (≈20 AWG)
W17
SP-0V-1 → ME442-C1-52 SENSORS GROUND
0.5 mm² (≈20 AWG)
W18
SP-0V-1 → ME442-C1-84 Sensor Ground
0.5 mm² (≈20 AWG)
W19
OEM-C84-1 Sensor supply +5V (VCC) → ME442-C1-45 5V REF
0.5 mm² (≈20 AWG)
W20
OEM-C84-5 Crank position (NE) → ME442-C1-80 CRANK VR+
0.5 mm² (≈20 AWG)
W21
OEM-C84-10 Cam position 1 (G1) → ME442-C1-22 CAM A VR+
0.5 mm² (≈20 AWG)
W22
OEM-C84-16 Cam position 2 (G2) → ME442-C1-23 CAM A VR-
0.5 mm² (≈20 AWG)
W23
OEM-C88-5 Knock sensor 1 (KNK1, front) → ME442-C1-53 KNOCK 1 SIGNAL
0.5 mm² (≈20 AWG)
W24
OEM-C88-4 Knock sensor 2 (KNK2, rear) → ME442-C1-54 KNOCK 2 SIGNAL
0.5 mm² (≈20 AWG)
W25
OEM-C88-24 Ignition 1 (IGT1) → ME442-C1-32 COIL 1
0.5 mm² (≈20 AWG)
W26
OEM-C88-16 Ignition 2 (IGT2) → ME442-C1-31 COIL 2
0.5 mm² (≈20 AWG)
W27
OEM-C88-15 Ignition 3 (IGT3) → ME442-C1-2 COIL 3
0.5 mm² (≈20 AWG)
W28
OEM-C88-26 Ignition 4 (IGT4) → ME442-C1-1 COIL 4
0.5 mm² (≈20 AWG)
W29
OEM-C88-30 Ignition 5 (IGT5) → ME442-C1-59 COIL 5
0.5 mm² (≈20 AWG)
W30
OEM-C88-29 Ignition 6 (IGT6) → ME442-C1-60 COIL 6
0.5 mm² (≈20 AWG)
W31
OEM-C88-10 Injector 1 (#10, cyl 1&4) → ME442-C1-63 INJECTOR 1
0.5 mm² (≈20 AWG)
W32
OEM-C88-9 Injector 2 (#20, cyl 3&5) → ME442-C1-4 INJECTOR 2
0.5 mm² (≈20 AWG)
W33
OEM-C88-8 Injector 3 (#30, cyl 2&6) → ME442-C1-33 INJECTOR 3
0.5 mm² (≈20 AWG)
W34
OEM-C84-8 Manifold pressure (PIM) → ME442-C1-26 ANA VOLT 1
0.5 mm² (≈20 AWG)
W35
OEM-C84-7 Throttle position (VTA1) → ME442-C1-56 ANA VOLT 2
0.5 mm² (≈20 AWG)
W36
OEM-C84-20 Coolant temperature (THW) → ME442-C1-86 ANA TEMP 1
0.5 mm² (≈20 AWG)
W37
OEM-C85-2 EFI main relay control (M-REL) → ME442-C1-73 LOW SIDE 1
0.5 mm² (≈20 AWG)
W38
OEM-C86-5 A/C clutch relay (ACMG) → ME442-C1-12 LOW SIDE 2
0.5 mm² (≈20 AWG)
W39
OEM-C88-3 O2 heater (HT) → ME442-C1-16 LSU HEATER -VE
0.5 mm² (≈20 AWG)
W40
OEM-C88-11 A/T shift solenoid 1 (S1) → ME442-C1-74 LOW SIDE 3
0.5 mm² (≈20 AWG)
W41
OEM-C88-23 ISC stepper coil 1 (ISCV1) → ME442-C1-44 LOW SIDE 4
0.5 mm² (≈20 AWG)
W42
OEM-C88-17 A/T shift solenoid 2 (S2) → ME442-C1-69 LOW SIDE 5
0.5 mm² (≈20 AWG)
W43
OEM-C88-22 ISC stepper coil 2 (ISCV2) → ME442-C1-39 LOW SIDE 6
0.5 mm² (≈20 AWG)
W44
OEM-C88-21 ISC stepper coil 3 (ISCV3) → ME442-C1-37 LOW SIDE RELAY 11
0.5 mm² (≈20 AWG)
W45
OEM-C88-20 ISC stepper coil 4 (ISCV4) → ME442-C1-42 LOW SIDE RELAY 12
0.5 mm² (≈20 AWG)
W46
OEM-C85-3 Check-engine lamp (W) → ME442-C1-72 LOW SIDE RELAY 13
0.5 mm² (≈20 AWG)
W47
OEM-C85-4 Fuel pump control (FPC) → ME442-C1-43 LOW SIDE RELAY 14
0.5 mm² (≈20 AWG)
W48
OEM-C86-8 Cat temp warning light (EGW) → ME442-C1-13 LOW SIDE RELAY 15
0.5 mm² (≈20 AWG)
W49
OEM-C88-27 A/T lock-up solenoid (S3) → ME442-C1-75 LOW SIDE RELAY 16
0.5 mm² (≈20 AWG)
W50
OEM-C88-7 EVAP purge VSV → ME442-C1-40 LOW SIDE RELAY 17
0.5 mm² (≈20 AWG)
W51
OEM-C84-12 TRAC throttle position (VTA2) → ME442-C1-17 ANA VOLT 3
0.5 mm² (≈20 AWG)
W52
OEM-C84-13 O2 sensor (OX1) → ME442-C1-18 ANA VOLT 4
0.5 mm² (≈20 AWG)
W53
OEM-C84-14 Intake air temperature (THA) → ME442-C1-57 ANA TEMP 2
0.5 mm² (≈20 AWG)
W54
OEM-C86-13 Cat temperature sensor (CCO) → ME442-C1-77 ANA TEMP 3
0.5 mm² (≈20 AWG)
W55
OEM-C86-12 No.1 speed sensor (SP1) → ME442-C1-6 DIG_IN 1
0.5 mm² (≈20 AWG)
W56
OEM-C84-4 No.2 speed sensor (SP2-) → ME442-C1-7 DIG_IN 2
0.5 mm² (≈20 AWG)
W57
OEM-C84-9 No.2 speed sensor (SP2+) → ME442-C1-8 DIG_IN 3
0.5 mm² (≈20 AWG)
W58
OEM-C84-15 OD direct-clutch speed sensor (NCO+) → ME442-C1-5 DIG_IN 4
0.5 mm² (≈20 AWG)
W59
OEM-C84-3 OD direct-clutch speed sensor (NCO-) → ME442-C1-62 DIG_IN 5
0.5 mm² (≈20 AWG)
W60
OEM-C85-1 Slave engine speed (NEO) → ME442-C1-34 DIG_IN 6
0.5 mm² (≈20 AWG)
W61
OEM-C85-5 Diagnostic test 1 (TE1) → ME442-C1-87 ANA VOLT 5
0.5 mm² (≈20 AWG)
W62
OEM-C86-7 A/T overdrive disable 1 (OD1) → ME442-C1-78 ANA VOLT 6
0.5 mm² (≈20 AWG)
W63
OEM-C86-10 A/T 2nd-gear indicator (2) → ME442-C1-48 ANA VOLT 7
0.5 mm² (≈20 AWG)