Lengths need a layout. Add bundles in Layout.
Not set yet: signal, colour, stripe, ident. Show
W1
OEM-E10-31 EFI main relay power (+B) → SP-14V-1
0.85 mm² (≈18 AWG)
W2
OEM-E10-32 EFI main relay power (+B1) → SP-14V-1
0.85 mm² (≈18 AWG)
W3
SP-14V-1 → ME221-C1-15 IGN +12V
0.85 mm² (≈18 AWG)
W4
SP-14V-1 → ME221-C1-64 VBAT
0.85 mm² (≈18 AWG)
W5
OEM-E9-4 Power ground (E11) → SP-GND-1
0.85 mm² (≈18 AWG)
W6
OEM-E9-69 Power ground (E1) → SP-GND-1
0.85 mm² (≈18 AWG)
W7
OEM-E9-79 Power ground (E02) → SP-GND-1
0.85 mm² (≈18 AWG)
W8
OEM-E9-80 Power ground (E01) → SP-GND-1
0.85 mm² (≈18 AWG)
W9
SP-GND-1 → ME221-C1-10 GROUND CHASSIS
0.85 mm² (≈18 AWG)
W10
SP-GND-1 → ME221-C1-61 GROUND
0.85 mm² (≈18 AWG)
W11
SP-GND-1 → ME221-C1-89 GROUND
0.85 mm² (≈18 AWG)
W12
SP-GND-1 → ME221-C1-90 GROUND
0.85 mm² (≈18 AWG)
W13
OEM-E9-65 Sensor ground (E2) → SP-0V-1
0.5 mm² (≈20 AWG)
W14
OEM-E9-7 Distributor ground (G-) → SP-0V-1
0.5 mm² (≈20 AWG)
W15
SP-0V-1 → ME221-C1-52 SENSORS GROUND
0.5 mm² (≈20 AWG)
W16
SP-0V-1 → ME221-C1-84 Sensor Ground
0.5 mm² (≈20 AWG)
W17
OEM-E9-41 Sensor supply +5V (VCC) → ME221-C1-45 5V REF
0.5 mm² (≈20 AWG)
W18
OEM-E9-27 Crank position (NE) → ME221-C1-80 CRANK VR+
0.5 mm² (≈20 AWG)
W19
OEM-E9-26 Cam position 1 (G1) → ME221-C1-22 CAM A VR+
0.5 mm² (≈20 AWG)
W20
OEM-E9-25 Cam position 2 (G2) → ME221-C1-23 CAM A VR-
0.5 mm² (≈20 AWG)
W21
OEM-E9-50 Knock sensor 1 (KNK1, front) → ME221-C1-53 KNOCK 1 SIGNAL
0.5 mm² (≈20 AWG)
W22
OEM-E9-57 Igniter trigger (IGT) → ME221-C1-32 COIL 1
0.5 mm² (≈20 AWG)
W23
OEM-E9-20 Injector 1 (#10, front) → ME221-C1-63 INJECTOR 1
0.5 mm² (≈20 AWG)
W24
OEM-E9-19 Injector 2 (#20) → ME221-C1-4 INJECTOR 2
0.5 mm² (≈20 AWG)
W25
OEM-E9-18 Injector 3 (#30) → ME221-C1-33 INJECTOR 3
0.5 mm² (≈20 AWG)
W26
OEM-E9-17 Injector 4 (#40) → ME221-C1-3 INJECTOR 4
0.5 mm² (≈20 AWG)
W27
OEM-E9-16 Injector 5 (#50) → ME221-C1-63 INJECTOR 1
0.5 mm² (≈20 AWG)
W28
OEM-E9-15 Injector 6 (#60, rear) → ME221-C1-4 INJECTOR 2
0.5 mm² (≈20 AWG)
W29
OEM-E9-62 Manifold pressure (PIM) → ME221-C1-26 ANA VOLT 1
0.5 mm² (≈20 AWG)
W30
OEM-E9-43 Throttle position (VTA1) → ME221-C1-56 ANA VOLT 2
0.5 mm² (≈20 AWG)
W31
OEM-E9-44 Coolant temperature (THW) → ME221-C1-86 ANA TEMP 1
0.5 mm² (≈20 AWG)
W32
OEM-E10-23 A/C clutch relay (ACMG) → ME221-C1-73 LOW SIDE 1
0.5 mm² (≈20 AWG)
W33
OEM-E10-24 EFI main relay control (M-REL) → ME221-C1-12 LOW SIDE 2
0.5 mm² (≈20 AWG)
W34
OEM-E9-10 A/T shift solenoid 1 (S1) → ME221-C1-74 LOW SIDE 3
0.5 mm² (≈20 AWG)
W35
OEM-E9-35 ISC stepper coil 1 (ISC1) → ME221-C1-44 LOW SIDE 4
0.5 mm² (≈20 AWG)
W36
OEM-E9-34 ISC stepper coil 2 (ISC2) → ME221-C1-69 LOW SIDE 5
0.5 mm² (≈20 AWG)
W37
OEM-E9-9 A/T shift solenoid 2 (S2) → ME221-C1-39 LOW SIDE 6
0.5 mm² (≈20 AWG)
W38
OEM-E9-33 ISC stepper coil 3 (ISC3) → ME221-C1-37 LOW SIDE RELAY 11
0.5 mm² (≈20 AWG)
W39
OEM-E9-32 ISC stepper coil 4 (ISC4) → ME221-C1-42 LOW SIDE RELAY 12
0.5 mm² (≈20 AWG)
W40
OEM-E10-22 Fuel pump control (FPC) → ME221-C1-72 LOW SIDE RELAY 13
0.5 mm² (≈20 AWG)
W41
OEM-E10-5 Cat-temp warning light (EGW) → ME221-C1-43 LOW SIDE RELAY 14
0.5 mm² (≈20 AWG)
W42
OEM-E10-6 Check-engine light (W) → ME221-C1-16 LSU HEATER -VE
0.5 mm² (≈20 AWG)
W43
OEM-E9-47 O2 sensor 2 (OX2, rear bank) → ME221-C1-17 ANA VOLT 3
0.5 mm² (≈20 AWG)
W44
OEM-E9-48 O2 sensor 1 (OX1, front bank) → ME221-C1-18 ANA VOLT 4
0.5 mm² (≈20 AWG)
W45
OEM-E10-29 Cat temperature sensor (CCO) → ME221-C1-57 ANA TEMP 2
0.5 mm² (≈20 AWG)
W46
OEM-E10-2 No.1 speed sensor (SP1) → ME221-C1-6 DIG_IN 1
0.5 mm² (≈20 AWG)
W47
OEM-E9-23 No.2 speed sensor (SP2+) → ME221-C1-7 DIG_IN 2
0.5 mm² (≈20 AWG)