Lengths need a layout. Add bundles in Layout.
Not set yet: signal, colour, stripe, ident. Show
W1
OEM-X-54 ECU power (+14V from main relay) → SP-14V-1
0.85 mm² (≈18 AWG)
W2
SP-14V-1 → ME360-C1-15 IGN +12V
0.85 mm² (≈18 AWG)
W3
SP-14V-1 → ME360-C1-64 VBAT
0.85 mm² (≈18 AWG)
W4
OEM-X-15 Ground → SP-GND-1
0.85 mm² (≈18 AWG)
W5
OEM-X-34 Ground (output stages) → SP-GND-1
0.85 mm² (≈18 AWG)
W6
OEM-X-55 Ground (ignition) → SP-GND-1
0.85 mm² (≈18 AWG)
W7
OEM-X-6 Ground (injector output stages) → SP-GND-1
0.85 mm² (≈18 AWG)
W8
SP-GND-1 → ME360-C1-10 GROUND CHASSIS
0.85 mm² (≈18 AWG)
W9
SP-GND-1 → ME360-C1-61 GROUND
0.85 mm² (≈18 AWG)
W10
SP-GND-1 → ME360-C1-89 GROUND
0.85 mm² (≈18 AWG)
W11
SP-GND-1 → ME360-C1-90 GROUND
0.85 mm² (≈18 AWG)
W12
OEM-X-28 Ground (electronics + sensor shielding) → SP-0V-1
0.5 mm² (≈20 AWG)
W13
OEM-X-40 O2 sensor signal ground → SP-0V-1
0.5 mm² (≈20 AWG)
W14
OEM-X-43 Crank position sensor (-) → SP-0V-1
0.5 mm² (≈20 AWG)
W15
OEM-X-44 Sensor ground (IAT/ECT/TPS) → SP-0V-1
0.5 mm² (≈20 AWG)
W16
OEM-X-71 Knock sensor ground/shield → SP-0V-1
0.5 mm² (≈20 AWG)
W17
SP-0V-1 → ME360-C1-52 SENSORS GROUND
0.5 mm² (≈20 AWG)
W18
SP-0V-1 → ME360-C1-84 Sensor Ground
0.5 mm² (≈20 AWG)
W19
OEM-X-59 +5V sensor supply → ME360-C1-45 5V REF
0.5 mm² (≈20 AWG)
W20
OEM-X-16 Crank position sensor (+) → ME360-C1-80 CRANK VR+
0.5 mm² (≈20 AWG)
W21
OEM-X-17 Camshaft position sensor (Hall) → ME360-C1-22 CAM A VR+
0.5 mm² (≈20 AWG)
W22
OEM-X-70 Knock sensor cylinders 1-3 → ME360-C1-53 KNOCK 1 SIGNAL
0.5 mm² (≈20 AWG)
W23
OEM-X-50 Ignition coil cylinder 1 → ME360-C1-32 COIL 1
0.5 mm² (≈20 AWG)
W24
OEM-X-51 Ignition coil cylinder 2 → ME360-C1-31 COIL 2
0.5 mm² (≈20 AWG)
W25
OEM-X-52 Ignition coil cylinder 3 → ME360-C1-2 COIL 3
0.5 mm² (≈20 AWG)
W26
OEM-X-23 Ignition coil cylinder 4 → ME360-C1-1 COIL 4
0.5 mm² (≈20 AWG)
W27
OEM-X-25 Ignition coil cylinder 5 → ME360-C1-59 COIL 5
0.5 mm² (≈20 AWG)
W28
OEM-X-24 Ignition coil cylinder 6 → ME360-C1-60 COIL 6
0.5 mm² (≈20 AWG)
W29
OEM-X-33 Injector cylinder 1 → ME360-C1-63 INJECTOR 1
0.5 mm² (≈20 AWG)
W30
OEM-X-32 Injector cylinder 2 → ME360-C1-4 INJECTOR 2
0.5 mm² (≈20 AWG)
W31
OEM-X-31 Injector cylinder 3 → ME360-C1-33 INJECTOR 3
0.5 mm² (≈20 AWG)
W32
OEM-X-5 Injector cylinder 4 → ME360-C1-3 INJECTOR 4
0.5 mm² (≈20 AWG)
W33
OEM-X-3 Injector cylinder 5 → ME360-C1-28 INJECTOR 5
0.5 mm² (≈20 AWG)
W34
OEM-X-4 Injector cylinder 6 → ME360-C1-58 INJECTOR 6
0.5 mm² (≈20 AWG)
W35
OEM-X-1 Fuel pump relay control → ME360-C1-37 LOW SIDE RELAY 11
0.5 mm² (≈20 AWG)
W36
OEM-X-27 Main relay control → ME360-C1-42 LOW SIDE RELAY 12
0.5 mm² (≈20 AWG)
W37
OEM-X-41 Mass air flow (MAF) signal → ME360-C1-26 ANA VOLT 1
0.5 mm² (≈20 AWG)
W38
OEM-X-73 Throttle position (TPS) → ME360-C1-56 ANA VOLT 2
0.5 mm² (≈20 AWG)
W39
OEM-X-78 Engine coolant temperature (ECT) → ME360-C1-86 ANA TEMP 1
0.5 mm² (≈20 AWG)
W40
OEM-X-38 O2 sensor heater relay control → ME360-C1-16 LSU HEATER -VE
0.5 mm² (≈20 AWG)
W41
OEM-X-2 Idle speed control valve (close winding) → ME360-C1-73 LOW SIDE 1
0.5 mm² (≈20 AWG)
W42
OEM-X-29 Idle speed control valve (open winding) → ME360-C1-12 LOW SIDE 2
0.5 mm² (≈20 AWG)
W43
OEM-X-36 Evap purge solenoid → ME360-C1-74 LOW SIDE 3
0.5 mm² (≈20 AWG)
W44
OEM-X-7 VANOS intake camshaft solenoid → ME360-C1-44 LOW SIDE 4
0.5 mm² (≈20 AWG)
W45
OEM-X-8 Check engine light (MIL) → ME360-C1-69 LOW SIDE 5
0.5 mm² (≈20 AWG)
W46
OEM-X-47 Tachometer output → ME360-C1-79 TACHOMETER
0.5 mm² (≈20 AWG)
W47
OEM-X-13 O2 sensor signal → ME360-C1-17 ANA VOLT 3
0.5 mm² (≈20 AWG)
W48
OEM-X-77 Intake air temperature (IAT) → ME360-C1-57 ANA TEMP 2
0.5 mm² (≈20 AWG)
W49
OEM-X-42 Vehicle speed signal → ME360-C1-6 DIG_IN 1
0.5 mm² (≈20 AWG)